From: Jiri Pirko <jiri@resnulli.us>
To: netdev@vger.kernel.org
Cc: davem@davemloft.net, idosch@mellanox.com, yotamg@mellanox.com,
eladr@mellanox.com, nogahf@mellanox.com, ogerlitz@mellanox.com,
sfeldma@gmail.com, roopa@cumulusnetworks.com, andy@greyhouse.net,
dsa@cumulusnetworks.com, tgraf@suug.ch, jhs@mojatatu.com,
linville@tuxdriver.com, ivecera@redhat.com
Subject: [patch net-next 12/18] mlxsw: spectrum: Add traps needed for router implementation
Date: Sat, 2 Jul 2016 09:26:34 +0200 [thread overview]
Message-ID: <1467444400-9480-13-git-send-email-jiri@resnulli.us> (raw)
In-Reply-To: <1467444400-9480-1-git-send-email-jiri@resnulli.us>
From: Jiri Pirko <jiri@mellanox.com>
ip2me:
To instruct HW to send trapped ip2me traffic to kernel, we have to add
this trap. Selection ip2me traffic is introduced later on in this set.
ARPs:
We are going to stop flooding to CPU port when netdev isn't bridged and
only get packets destined to the netdev's IP address and certain control
packets.
Add traps for ARP request (broadcast) and response (unicast) in order to
get these to the CPU and resolve neighbours.
host miss:
If a packet is routed through a directly connected route and its
destination IP is not in the device's neighbour table, then we need to
trap it to CPU. This will cause the host to resolve the MAC of the
neighbour, which will be eventually programmed to the device's table.
router ingress:
In order to trap packets in router part.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
---
drivers/net/ethernet/mellanox/mlxsw/spectrum.c | 25 +++++++++++++++++++++++++
drivers/net/ethernet/mellanox/mlxsw/trap.h | 5 +++++
2 files changed, 30 insertions(+)
diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
index de30763..f0799898 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
@@ -2255,6 +2255,31 @@ static const struct mlxsw_rx_listener mlxsw_sp_rx_listener[] = {
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_IGMP_V3_REPORT,
},
+ {
+ .func = mlxsw_sp_rx_listener_func,
+ .local_port = MLXSW_PORT_DONT_CARE,
+ .trap_id = MLXSW_TRAP_ID_ARPBC,
+ },
+ {
+ .func = mlxsw_sp_rx_listener_func,
+ .local_port = MLXSW_PORT_DONT_CARE,
+ .trap_id = MLXSW_TRAP_ID_ARPUC,
+ },
+ {
+ .func = mlxsw_sp_rx_listener_func,
+ .local_port = MLXSW_PORT_DONT_CARE,
+ .trap_id = MLXSW_TRAP_ID_IP2ME,
+ },
+ {
+ .func = mlxsw_sp_rx_listener_func,
+ .local_port = MLXSW_PORT_DONT_CARE,
+ .trap_id = MLXSW_TRAP_ID_RTR_INGRESS0,
+ },
+ {
+ .func = mlxsw_sp_rx_listener_func,
+ .local_port = MLXSW_PORT_DONT_CARE,
+ .trap_id = MLXSW_TRAP_ID_HOST_MISS_IPV4,
+ },
};
static int mlxsw_sp_traps_init(struct mlxsw_sp *mlxsw_sp)
diff --git a/drivers/net/ethernet/mellanox/mlxsw/trap.h b/drivers/net/ethernet/mellanox/mlxsw/trap.h
index 53a9550..470d769 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/trap.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/trap.h
@@ -54,6 +54,11 @@ enum {
MLXSW_TRAP_ID_IGMP_V2_REPORT = 0x32,
MLXSW_TRAP_ID_IGMP_V2_LEAVE = 0x33,
MLXSW_TRAP_ID_IGMP_V3_REPORT = 0x34,
+ MLXSW_TRAP_ID_ARPBC = 0x50,
+ MLXSW_TRAP_ID_ARPUC = 0x51,
+ MLXSW_TRAP_ID_IP2ME = 0x5F,
+ MLXSW_TRAP_ID_RTR_INGRESS0 = 0x70,
+ MLXSW_TRAP_ID_HOST_MISS_IPV4 = 0x90,
MLXSW_TRAP_ID_MAX = 0x1FF
};
--
2.5.5
next prev parent reply other threads:[~2016-07-02 7:27 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-07-02 7:26 [patch net-next 00/18] mlxsw: Do preparations before ipv4 router offload introduction Jiri Pirko
2016-07-02 7:26 ` [patch net-next 01/18] mlxsw: spectrum: Send untagged packets through a port netdev Jiri Pirko
2016-07-02 7:26 ` [patch net-next 02/18] mlxsw: spectrum: Remove VLANs configuration via SELF flag Jiri Pirko
2016-07-02 7:26 ` [patch net-next 03/18] mlxsw: spectrum: Sync PVID vPort LAG status Jiri Pirko
2016-07-02 7:26 ` [patch net-next 04/18] mlxsw: spectrum: Remove RIF from PVID vPort when joining / leaving LAG Jiri Pirko
2016-07-02 7:26 ` [patch net-next 05/18] mlxsw: reg: Add Router General Configuration Register Jiri Pirko
2016-07-02 7:26 ` [patch net-next 06/18] mlxsw: spectrum: Initialize ports at the end of init sequence Jiri Pirko
2016-07-02 7:26 ` [patch net-next 07/18] mlxsw: spectrum_router: Add basic ipv4 router initialization Jiri Pirko
2016-07-02 7:26 ` [patch net-next 08/18] mlxsw: spectrum: Add router interface struct Jiri Pirko
2016-07-02 7:26 ` [patch net-next 09/18] mlxsw: reg: Add FDB action to forward to router Jiri Pirko
2016-07-02 7:26 ` [patch net-next 10/18] mlxsw: reg: Add Router Interface Table Register Jiri Pirko
2016-07-02 7:26 ` [patch net-next 11/18] mlxsw: spectrum: Use action 'discard' when removing traps Jiri Pirko
2016-07-02 7:26 ` Jiri Pirko [this message]
2016-07-02 7:26 ` [patch net-next 13/18] mlxsw: spectrum: Add couple of lower device helper functions Jiri Pirko
2016-07-02 7:26 ` [patch net-next 14/18] mlxsw: spectrum: Edit RIF properties based on netdev events Jiri Pirko
2016-07-02 7:26 ` [patch net-next 15/18] mlxsw: spectrum: Introduce support for router interfaces Jiri Pirko
2016-07-02 7:26 ` [patch net-next 16/18] mlxsw: spectrum: Unsplit the vFID range Jiri Pirko
2016-07-02 7:26 ` [patch net-next 17/18] mlxsw: spectrum: Configure FIDs based on bridge events Jiri Pirko
2016-07-02 7:26 ` [patch net-next 18/18] mlxsw: spectrum: Enable L3 interfaces on top of bridge devices Jiri Pirko
2016-07-02 8:37 ` [patch net-next 00/18] mlxsw: Do preparations before ipv4 router offload introduction Jiri Pirko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1467444400-9480-13-git-send-email-jiri@resnulli.us \
--to=jiri@resnulli.us \
--cc=andy@greyhouse.net \
--cc=davem@davemloft.net \
--cc=dsa@cumulusnetworks.com \
--cc=eladr@mellanox.com \
--cc=idosch@mellanox.com \
--cc=ivecera@redhat.com \
--cc=jhs@mojatatu.com \
--cc=linville@tuxdriver.com \
--cc=netdev@vger.kernel.org \
--cc=nogahf@mellanox.com \
--cc=ogerlitz@mellanox.com \
--cc=roopa@cumulusnetworks.com \
--cc=sfeldma@gmail.com \
--cc=tgraf@suug.ch \
--cc=yotamg@mellanox.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).