From: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
To: <michal.simek@xilinx.com>, <soren.brinkmann@xilinx.com>,
<appanad@xilinx.com>, <f.fainelli@gmail.com>, <andrew@lunn.ch>
Cc: <linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <netdev@vger.kernel.org>
Subject: [PATCH 2/2] net: phy: Fix race conditions in the driver
Date: Fri, 19 Aug 2016 18:18:11 +0530 [thread overview]
Message-ID: <1471610891-13353-2-git-send-email-appanad@xilinx.com> (raw)
In-Reply-To: <1471610891-13353-1-git-send-email-appanad@xilinx.com>
This patch fixes the below race conditions in the driver.
---> Fix Opps after unload the driver as a module
---> Use spin locks where relevant.
---> Take reference on the external phy to prevent issues
when phy driver is unloaded.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
---
drivers/net/phy/xilinx_gmii2rgmii.c | 32 +++++++++++++++++++++++++++++++-
1 file changed, 31 insertions(+), 1 deletion(-)
diff --git a/drivers/net/phy/xilinx_gmii2rgmii.c b/drivers/net/phy/xilinx_gmii2rgmii.c
index 7336fd0..cdd9d95 100644
--- a/drivers/net/phy/xilinx_gmii2rgmii.c
+++ b/drivers/net/phy/xilinx_gmii2rgmii.c
@@ -34,6 +34,7 @@ struct gmii2rgmii {
struct phy_driver *phy_drv;
struct phy_driver conv_phy_drv;
int addr;
+ spinlock_t phy_lock;
};
static int xgmiitorgmii_read_status(struct phy_device *phydev)
@@ -55,7 +56,7 @@ static int xgmiitorgmii_read_status(struct phy_device *phydev)
val |= BMCR_SPEED1000;
else if (phydev->speed == SPEED_100)
val |= BMCR_SPEED100;
- else
+ else if (phydev->speed == SPEED_10)
val |= BMCR_SPEED10;
err = mdiobus_write(phydev->mdio.bus, priv->addr, XILINX_GMII2RGMII_REG,
@@ -71,6 +72,8 @@ int xgmiitorgmii_probe(struct mdio_device *mdiodev)
struct device *dev = &mdiodev->dev;
struct device_node *np = dev->of_node, *phy_node;
struct gmii2rgmii *priv;
+ struct mii_bus *bus;
+ unsigned long flags;
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
@@ -88,17 +91,43 @@ int xgmiitorgmii_probe(struct mdio_device *mdiodev)
return -EPROBE_DEFER;
}
+ spin_lock_init(&priv->phy_lock);
+
+ bus = priv->phy_dev->mdio.bus;
+ if (!try_module_get(bus->owner)) {
+ dev_err(dev, "failed to get the bus module\n");
+ return -EIO;
+ }
+
+ get_device(&priv->phy_dev->mdio.dev);
+
priv->addr = mdiodev->addr;
priv->phy_drv = priv->phy_dev->drv;
memcpy(&priv->conv_phy_drv, priv->phy_dev->drv,
sizeof(struct phy_driver));
priv->conv_phy_drv.read_status = xgmiitorgmii_read_status;
priv->phy_dev->priv = priv;
+ spin_lock_irqsave(&priv->phy_lock, flags);
priv->phy_dev->drv = &priv->conv_phy_drv;
+ spin_unlock_irqrestore(&priv->phy_lock, flags);
+
+ dev_set_drvdata(dev, priv);
return 0;
}
+static void xgmiitorgmii_remove(struct mdio_device *mdiodev)
+{
+ struct gmii2rgmii *priv = dev_get_drvdata(&mdiodev->dev);
+ struct mii_bus *bus;
+
+ bus = priv->phy_dev->mdio.bus;
+
+ put_device(&priv->phy_dev->mdio.dev);
+ module_put(bus->owner);
+ phy_disconnect(priv->phy_dev);
+}
+
static const struct of_device_id xgmiitorgmii_of_match[] = {
{ .compatible = "xlnx,gmii-to-rgmii-1.0" },
{},
@@ -107,6 +136,7 @@ MODULE_DEVICE_TABLE(of, xgmiitorgmii_of_match);
static struct mdio_driver xgmiitorgmii_driver = {
.probe = xgmiitorgmii_probe,
+ .remove = xgmiitorgmii_remove,
.mdiodrv.driver = {
.name = "xgmiitorgmii",
.of_match_table = xgmiitorgmii_of_match,
--
2.1.2
next prev parent reply other threads:[~2016-08-19 12:49 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-08-19 12:48 [PATCH 1/2] net: phy: Add error checks in the driver Kedareswara rao Appana
2016-08-19 12:48 ` Kedareswara rao Appana [this message]
2016-08-19 13:24 ` [PATCH 2/2] net: phy: Fix race conditions " Andrew Lunn
2016-08-19 13:15 ` [PATCH 1/2] net: phy: Add error checks " Andrew Lunn
2016-08-19 13:18 ` Appana Durga Kedareswara Rao
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1471610891-13353-2-git-send-email-appanad@xilinx.com \
--to=appana.durga.rao@xilinx.com \
--cc=andrew@lunn.ch \
--cc=appanad@xilinx.com \
--cc=f.fainelli@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=michal.simek@xilinx.com \
--cc=netdev@vger.kernel.org \
--cc=soren.brinkmann@xilinx.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).