* [PATCH] net: tg3: use new api ethtool_{get|set}_link_ksettings
@ 2016-09-25 21:31 Philippe Reynes
2016-09-26 16:54 ` Michael Chan
2016-09-27 0:17 ` David Miller
0 siblings, 2 replies; 3+ messages in thread
From: Philippe Reynes @ 2016-09-25 21:31 UTC (permalink / raw)
To: siva.kallam, prashant, mchan, f.fainelli, davem
Cc: netdev, linux-kernel, Philippe Reynes
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
---
drivers/net/ethernet/broadcom/tg3.c | 112 +++++++++++++++++++----------------
1 files changed, 62 insertions(+), 50 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index a2551bc..2726f03 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -12079,95 +12079,107 @@ static int tg3_set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom,
return ret;
}
-static int tg3_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+static int tg3_get_link_ksettings(struct net_device *dev,
+ struct ethtool_link_ksettings *cmd)
{
struct tg3 *tp = netdev_priv(dev);
+ u32 supported, advertising;
if (tg3_flag(tp, USE_PHYLIB)) {
struct phy_device *phydev;
if (!(tp->phy_flags & TG3_PHYFLG_IS_CONNECTED))
return -EAGAIN;
phydev = mdiobus_get_phy(tp->mdio_bus, tp->phy_addr);
- return phy_ethtool_gset(phydev, cmd);
+ return phy_ethtool_ksettings_get(phydev, cmd);
}
- cmd->supported = (SUPPORTED_Autoneg);
+ supported = (SUPPORTED_Autoneg);
if (!(tp->phy_flags & TG3_PHYFLG_10_100_ONLY))
- cmd->supported |= (SUPPORTED_1000baseT_Half |
- SUPPORTED_1000baseT_Full);
+ supported |= (SUPPORTED_1000baseT_Half |
+ SUPPORTED_1000baseT_Full);
if (!(tp->phy_flags & TG3_PHYFLG_ANY_SERDES)) {
- cmd->supported |= (SUPPORTED_100baseT_Half |
- SUPPORTED_100baseT_Full |
- SUPPORTED_10baseT_Half |
- SUPPORTED_10baseT_Full |
- SUPPORTED_TP);
- cmd->port = PORT_TP;
+ supported |= (SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_10baseT_Half |
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_TP);
+ cmd->base.port = PORT_TP;
} else {
- cmd->supported |= SUPPORTED_FIBRE;
- cmd->port = PORT_FIBRE;
+ supported |= SUPPORTED_FIBRE;
+ cmd->base.port = PORT_FIBRE;
}
+ ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.supported,
+ supported);
- cmd->advertising = tp->link_config.advertising;
+ advertising = tp->link_config.advertising;
if (tg3_flag(tp, PAUSE_AUTONEG)) {
if (tp->link_config.flowctrl & FLOW_CTRL_RX) {
if (tp->link_config.flowctrl & FLOW_CTRL_TX) {
- cmd->advertising |= ADVERTISED_Pause;
+ advertising |= ADVERTISED_Pause;
} else {
- cmd->advertising |= ADVERTISED_Pause |
- ADVERTISED_Asym_Pause;
+ advertising |= ADVERTISED_Pause |
+ ADVERTISED_Asym_Pause;
}
} else if (tp->link_config.flowctrl & FLOW_CTRL_TX) {
- cmd->advertising |= ADVERTISED_Asym_Pause;
+ advertising |= ADVERTISED_Asym_Pause;
}
}
+ ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.advertising,
+ advertising);
+
if (netif_running(dev) && tp->link_up) {
- ethtool_cmd_speed_set(cmd, tp->link_config.active_speed);
- cmd->duplex = tp->link_config.active_duplex;
- cmd->lp_advertising = tp->link_config.rmt_adv;
+ cmd->base.speed = tp->link_config.active_speed;
+ cmd->base.duplex = tp->link_config.active_duplex;
+ ethtool_convert_legacy_u32_to_link_mode(
+ cmd->link_modes.lp_advertising,
+ tp->link_config.rmt_adv);
+
if (!(tp->phy_flags & TG3_PHYFLG_ANY_SERDES)) {
if (tp->phy_flags & TG3_PHYFLG_MDIX_STATE)
- cmd->eth_tp_mdix = ETH_TP_MDI_X;
+ cmd->base.eth_tp_mdix = ETH_TP_MDI_X;
else
- cmd->eth_tp_mdix = ETH_TP_MDI;
+ cmd->base.eth_tp_mdix = ETH_TP_MDI;
}
} else {
- ethtool_cmd_speed_set(cmd, SPEED_UNKNOWN);
- cmd->duplex = DUPLEX_UNKNOWN;
- cmd->eth_tp_mdix = ETH_TP_MDI_INVALID;
- }
- cmd->phy_address = tp->phy_addr;
- cmd->transceiver = XCVR_INTERNAL;
- cmd->autoneg = tp->link_config.autoneg;
- cmd->maxtxpkt = 0;
- cmd->maxrxpkt = 0;
+ cmd->base.speed = SPEED_UNKNOWN;
+ cmd->base.duplex = DUPLEX_UNKNOWN;
+ cmd->base.eth_tp_mdix = ETH_TP_MDI_INVALID;
+ }
+ cmd->base.phy_address = tp->phy_addr;
+ cmd->base.autoneg = tp->link_config.autoneg;
return 0;
}
-static int tg3_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+static int tg3_set_link_ksettings(struct net_device *dev,
+ const struct ethtool_link_ksettings *cmd)
{
struct tg3 *tp = netdev_priv(dev);
- u32 speed = ethtool_cmd_speed(cmd);
+ u32 speed = cmd->base.speed;
+ u32 advertising;
if (tg3_flag(tp, USE_PHYLIB)) {
struct phy_device *phydev;
if (!(tp->phy_flags & TG3_PHYFLG_IS_CONNECTED))
return -EAGAIN;
phydev = mdiobus_get_phy(tp->mdio_bus, tp->phy_addr);
- return phy_ethtool_sset(phydev, cmd);
+ return phy_ethtool_ksettings_set(phydev, cmd);
}
- if (cmd->autoneg != AUTONEG_ENABLE &&
- cmd->autoneg != AUTONEG_DISABLE)
+ if (cmd->base.autoneg != AUTONEG_ENABLE &&
+ cmd->base.autoneg != AUTONEG_DISABLE)
return -EINVAL;
- if (cmd->autoneg == AUTONEG_DISABLE &&
- cmd->duplex != DUPLEX_FULL &&
- cmd->duplex != DUPLEX_HALF)
+ if (cmd->base.autoneg == AUTONEG_DISABLE &&
+ cmd->base.duplex != DUPLEX_FULL &&
+ cmd->base.duplex != DUPLEX_HALF)
return -EINVAL;
- if (cmd->autoneg == AUTONEG_ENABLE) {
+ ethtool_convert_link_mode_to_legacy_u32(&advertising,
+ cmd->link_modes.advertising);
+
+ if (cmd->base.autoneg == AUTONEG_ENABLE) {
u32 mask = ADVERTISED_Autoneg |
ADVERTISED_Pause |
ADVERTISED_Asym_Pause;
@@ -12185,7 +12197,7 @@ static int tg3_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
else
mask |= ADVERTISED_FIBRE;
- if (cmd->advertising & ~mask)
+ if (advertising & ~mask)
return -EINVAL;
mask &= (ADVERTISED_1000baseT_Half |
@@ -12195,13 +12207,13 @@ static int tg3_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
ADVERTISED_10baseT_Half |
ADVERTISED_10baseT_Full);
- cmd->advertising &= mask;
+ advertising &= mask;
} else {
if (tp->phy_flags & TG3_PHYFLG_ANY_SERDES) {
if (speed != SPEED_1000)
return -EINVAL;
- if (cmd->duplex != DUPLEX_FULL)
+ if (cmd->base.duplex != DUPLEX_FULL)
return -EINVAL;
} else {
if (speed != SPEED_100 &&
@@ -12212,16 +12224,16 @@ static int tg3_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
tg3_full_lock(tp, 0);
- tp->link_config.autoneg = cmd->autoneg;
- if (cmd->autoneg == AUTONEG_ENABLE) {
- tp->link_config.advertising = (cmd->advertising |
+ tp->link_config.autoneg = cmd->base.autoneg;
+ if (cmd->base.autoneg == AUTONEG_ENABLE) {
+ tp->link_config.advertising = (advertising |
ADVERTISED_Autoneg);
tp->link_config.speed = SPEED_UNKNOWN;
tp->link_config.duplex = DUPLEX_UNKNOWN;
} else {
tp->link_config.advertising = 0;
tp->link_config.speed = speed;
- tp->link_config.duplex = cmd->duplex;
+ tp->link_config.duplex = cmd->base.duplex;
}
tp->phy_flags |= TG3_PHYFLG_USER_CONFIGURED;
@@ -14094,8 +14106,6 @@ static int tg3_get_eee(struct net_device *dev, struct ethtool_eee *edata)
}
static const struct ethtool_ops tg3_ethtool_ops = {
- .get_settings = tg3_get_settings,
- .set_settings = tg3_set_settings,
.get_drvinfo = tg3_get_drvinfo,
.get_regs_len = tg3_get_regs_len,
.get_regs = tg3_get_regs,
@@ -14128,6 +14138,8 @@ static const struct ethtool_ops tg3_ethtool_ops = {
.get_ts_info = tg3_get_ts_info,
.get_eee = tg3_get_eee,
.set_eee = tg3_set_eee,
+ .get_link_ksettings = tg3_get_link_ksettings,
+ .set_link_ksettings = tg3_set_link_ksettings,
};
static struct rtnl_link_stats64 *tg3_get_stats64(struct net_device *dev,
--
1.7.4.4
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] net: tg3: use new api ethtool_{get|set}_link_ksettings
2016-09-25 21:31 [PATCH] net: tg3: use new api ethtool_{get|set}_link_ksettings Philippe Reynes
@ 2016-09-26 16:54 ` Michael Chan
2016-09-27 0:17 ` David Miller
1 sibling, 0 replies; 3+ messages in thread
From: Michael Chan @ 2016-09-26 16:54 UTC (permalink / raw)
To: Philippe Reynes
Cc: Siva Reddy Kallam, Prashant Sreedharan, Michael Chan,
Florian Fainelli, David Miller, Netdev, open list
On Sun, Sep 25, 2016 at 2:31 PM, Philippe Reynes <tremyfr@gmail.com> wrote:
> The ethtool api {get|set}_settings is deprecated.
> We move this driver to new api {get|set}_link_ksettings.
>
> Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Looks good to me. Thanks.
Acked-by: Michael Chan <michael.chan@broadcom.com>
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH] net: tg3: use new api ethtool_{get|set}_link_ksettings
2016-09-25 21:31 [PATCH] net: tg3: use new api ethtool_{get|set}_link_ksettings Philippe Reynes
2016-09-26 16:54 ` Michael Chan
@ 2016-09-27 0:17 ` David Miller
1 sibling, 0 replies; 3+ messages in thread
From: David Miller @ 2016-09-27 0:17 UTC (permalink / raw)
To: tremyfr; +Cc: siva.kallam, prashant, mchan, f.fainelli, netdev, linux-kernel
From: Philippe Reynes <tremyfr@gmail.com>
Date: Sun, 25 Sep 2016 23:31:24 +0200
> The ethtool api {get|set}_settings is deprecated.
> We move this driver to new api {get|set}_link_ksettings.
>
> Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Applied, thanks.
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2016-09-27 0:17 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-09-25 21:31 [PATCH] net: tg3: use new api ethtool_{get|set}_link_ksettings Philippe Reynes
2016-09-26 16:54 ` Michael Chan
2016-09-27 0:17 ` David Miller
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).