From: Timur Tabi <timur@codeaurora.org>
To: David Miller <davem@davemloft.net>, netdev@vger.kernel.org
Subject: [PATCH 1/5] [net-next] net: qcom/emac: display the phy driver info after we connect
Date: Fri, 27 Jan 2017 16:43:43 -0600 [thread overview]
Message-ID: <1485557028-32510-2-git-send-email-timur@codeaurora.org> (raw)
In-Reply-To: <1485557028-32510-1-git-send-email-timur@codeaurora.org>
The PHY driver is attached only when the driver calls
phy_connect_direct(). Calling phy_attached_print() to display
information about the PHY driver prior to that point is meaningless.
The interface can be brought down, a new PHY driver can be loaded,
and the interface then brought back up. This is the correct time
to display information about the attached driver.
Since phy_attached_print() also prints information about the
interrupt, that needs to be set as well.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
---
drivers/net/ethernet/qualcomm/emac/emac-mac.c | 4 +++-
drivers/net/ethernet/qualcomm/emac/emac-phy.c | 3 ---
2 files changed, 3 insertions(+), 4 deletions(-)
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-mac.c b/drivers/net/ethernet/qualcomm/emac/emac-mac.c
index e4793d7..155e273 100644
--- a/drivers/net/ethernet/qualcomm/emac/emac-mac.c
+++ b/drivers/net/ethernet/qualcomm/emac/emac-mac.c
@@ -981,6 +981,7 @@ int emac_mac_up(struct emac_adapter *adpt)
emac_mac_config(adpt);
emac_mac_rx_descs_refill(adpt, &adpt->rx_q);
+ adpt->phydev->irq = PHY_IGNORE_INTERRUPT;
ret = phy_connect_direct(netdev, adpt->phydev, emac_adjust_link,
PHY_INTERFACE_MODE_SGMII);
if (ret) {
@@ -988,11 +989,12 @@ int emac_mac_up(struct emac_adapter *adpt)
return ret;
}
+ phy_attached_print(adpt->phydev, NULL);
+
/* enable mac irq */
writel((u32)~DIS_INT, adpt->base + EMAC_INT_STATUS);
writel(adpt->irq.mask, adpt->base + EMAC_INT_MASK);
- adpt->phydev->irq = PHY_IGNORE_INTERRUPT;
phy_start(adpt->phydev);
napi_enable(&adpt->rx_q.napi);
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-phy.c b/drivers/net/ethernet/qualcomm/emac/emac-phy.c
index 1d7852f..441c1936 100644
--- a/drivers/net/ethernet/qualcomm/emac/emac-phy.c
+++ b/drivers/net/ethernet/qualcomm/emac/emac-phy.c
@@ -226,8 +226,5 @@ int emac_phy_config(struct platform_device *pdev, struct emac_adapter *adpt)
return -ENODEV;
}
- if (adpt->phydev->drv)
- phy_attached_print(adpt->phydev, NULL);
-
return 0;
}
--
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc. Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
next prev parent reply other threads:[~2017-01-27 22:55 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-27 22:43 [PATCH 0/5] [net-next] net: qcom/emac: Timur Tabi
2017-01-27 22:43 ` Timur Tabi [this message]
2017-01-27 22:43 ` [PATCH 2/5] [net-next] net: qcom/emac: always use autonegotiation to configure the SGMII link Timur Tabi
2017-01-27 22:43 ` [PATCH 3/5] [net-next] net: qcom/emac: do not call emac_mac_start twice Timur Tabi
2017-01-27 22:43 ` [PATCH 4/4] [net-next] net: qcom/emac: add an error interrupt handler for the sgmii Timur Tabi
2017-01-27 23:21 ` Timur Tabi
2017-01-27 22:43 ` [PATCH 4/5] [net-next] net: qcom/emac: remove extraneous wake-on-lan code Timur Tabi
2017-01-27 22:43 ` [PATCH 5/5] [net-next] net: qcom/emac: add an error interrupt handler for the sgmii Timur Tabi
2017-01-30 0:07 ` [PATCH 0/5] [net-next] net: qcom/emac: David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1485557028-32510-2-git-send-email-timur@codeaurora.org \
--to=timur@codeaurora.org \
--cc=davem@davemloft.net \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).