From: thor.thayer@linux.intel.com
To: peppe.cavallaro@st.com, alexandre.torgue@st.com
Cc: netdev@vger.kernel.org, thor.thayer@linux.intel.com
Subject: [PATCH] net: stmmac: Adjust dump offset of DMA registers for ethtool
Date: Fri, 21 Jul 2017 16:35:09 -0500 [thread overview]
Message-ID: <1500672909-24408-1-git-send-email-thor.thayer@linux.intel.com> (raw)
From: Thor Thayer <thor.thayer@linux.intel.com>
The commit fbf68229ffe7 ("net: stmmac: unify registers dumps methods")
in the Linux kernel modified the register dump to store the DMA registers
at the DMA register offset (0x1000) but ethtool (stmmac.c) looks for the
DMA registers after the MAC registers which is offset 55.
This patch copies the DMA registers from the higher offset to the offset
where ethtool expects them.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
---
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 2 +-
drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c | 2 +-
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h | 3 +++
drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c | 5 +++++
4 files changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
index cc4ea13..ec539f7 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
@@ -205,7 +205,7 @@ static void dwmac1000_dump_dma_regs(void __iomem *ioaddr, u32 *reg_space)
{
int i;
- for (i = 0; i < 23; i++)
+ for (i = 0; i < NUM_DWMAC1000_DMA_REGS; i++)
if ((i < 12) || (i > 17))
reg_space[DMA_BUS_MODE / 4 + i] =
readl(ioaddr + DMA_BUS_MODE + i * 4);
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c
index eef2f22..6502b9a 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c
@@ -70,7 +70,7 @@ static void dwmac100_dump_dma_regs(void __iomem *ioaddr, u32 *reg_space)
{
int i;
- for (i = 0; i < 9; i++)
+ for (i = 0; i < NUM_DWMAC100_DMA_REGS; i++)
reg_space[DMA_BUS_MODE / 4 + i] =
readl(ioaddr + DMA_BUS_MODE + i * 4);
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h b/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h
index 56e485f..3107d19 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h
@@ -136,6 +136,9 @@
#define DMA_STATUS_TI 0x00000001 /* Transmit Interrupt */
#define DMA_CONTROL_FTF 0x00100000 /* Flush transmit FIFO */
+#define NUM_DWMAC100_DMA_REGS 9
+#define NUM_DWMAC1000_DMA_REGS 23
+
void dwmac_enable_dma_transmission(void __iomem *ioaddr);
void dwmac_enable_dma_irq(void __iomem *ioaddr);
void dwmac_disable_dma_irq(void __iomem *ioaddr);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
index 690b7c1..2ffb5b1 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
@@ -33,6 +33,8 @@
#define MAC100_ETHTOOL_NAME "st_mac100"
#define GMAC_ETHTOOL_NAME "st_gmac"
+#define ETHTOOL_DMA_OFFSET 55
+
struct stmmac_stats {
char stat_string[ETH_GSTRING_LEN];
int sizeof_stat;
@@ -443,6 +445,9 @@ static void stmmac_ethtool_gregs(struct net_device *dev,
priv->hw->mac->dump_regs(priv->hw, reg_space);
priv->hw->dma->dump_regs(priv->ioaddr, reg_space);
+ /* Copy DMA registers to where ethtool expects them */
+ memcpy(®_space[ETHTOOL_DMA_OFFSET], ®_space[DMA_BUS_MODE / 4],
+ NUM_DWMAC1000_DMA_REGS * 4);
}
static void
--
2.7.4
next reply other threads:[~2017-07-21 21:32 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-07-21 21:35 thor.thayer [this message]
2017-07-24 23:20 ` [PATCH] net: stmmac: Adjust dump offset of DMA registers for ethtool David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1500672909-24408-1-git-send-email-thor.thayer@linux.intel.com \
--to=thor.thayer@linux.intel.com \
--cc=alexandre.torgue@st.com \
--cc=netdev@vger.kernel.org \
--cc=peppe.cavallaro@st.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).