Re: [RFT net-next v3 0/5] dwmac-meson8b: RGMII clock fixes for Meson8b

[Jerome Brunet <jbrunet@baylibre.com>]

On Fri, 2017-12-29 at 02:31 +0100, Emiliano Ingrassia wrote:
> Hi Martin, Hi Dave,
> 
> On Thu, Dec 28, 2017 at 11:21:23PM +0100, Martin Blumenstingl wrote:
> > Hi Dave,
> > 
> > please do not apply this series until it got a Tested-by from Emiliano.
> > 
> > 
> > Hi Emiliano,
> > 
> > you reported [0] that you couldn't get dwmac-meson8b to work on your
> > Odroid-C1. With your findings (register dumps, clk_summary output, etc.)
> > I think I was able to find a fix: it consists of two patches (which you
> > find in this series)
> > 
> > Unfortunately I don't have any Meson8b boards with RGMII PHY so I could
> > only partially test this (I could only check if the clocks were
> > calculated correctly when using a dummy 500002394Hz input clock instead
> > of MPLL2).
> > 
> > Could you please give this series a try and let me know about the
> > results?
> > You obviously still need your two "ARM: dts: meson8b" patches which
> > - add the amlogic,meson8b-dwmac" compatible to meson8b.dtsi
> > - enable Ethernet on the Odroid-C1
> > 
> > When testing on Meson8b this also needs a fix for the MPLL clock driver:
> > "clk: meson: mpll: use 64-bit maths in params_from_rate", see:
> > https://patchwork.kernel.org/patch/10131677/
> > 
> > 
> > I have tested this myself on a Khadas VIM (GXL SoC, internal RMII PHY)
> > and a Khadas VIM2 (GXM SoC, external RGMII PHY). Both are still working
> > fine (so let's hope that this also fixes your Meson8b issue :)).
> > 
> > 
> > changes since v1 at [1]:
> > - changed the subject of the cover-letter to indicate that this is all
> >   about the RGMII clock
> > - added PATCH #1 which ensures that we don't unnecessarily change the
> >   parent clocks in RMII mode (and also makes the code easier to
> >   understand)
> > - changed subject of PATCH #2 (formerly PATCH #1) to state that this
> >   is about the RGMII clock
> > - added Jerome's Reviewed-by to PATCH #2 (formerly PATCH #1)
> > - replaced PATCH #3 (formerly PATCH #2) with one that sets
> >   CLK_SET_RATE_PARENT on the mux and thus re-configures the MPLL2 clock
> >   on Meson8b correctly
> > 
> > changes since v2 at [2]:
> > - added PATCH #2 to make the following patch easier
> > - Emiliano reported that there's currently another bug in the
> >   dwmac-meson8b driver which prevents it from working with RGMII PHYs on
> >   Meson8b: bit 10 of the PRG_ETH0 register is configures a clock gate
> >   (instead of a divide by 5 or divide by 10 clock divider). This has not
> >   been visible on GXBB and later due to the input clock which always led
> >   to a selection of "divide by 10" (which is done internally in the IP
> >   block, but the bit actually means "enable RGMII clock output").
> >   PATCH #3 was added to address this issue.
> > - the commit message of PATCH #4 and #5 (formerly PATCH #2 and #3) were
> >   updated and the patch itself rebased because the m25_div clock was
> >   removed with the new PATCH #3 (so some of the statements were not
> >   valid anymore)
> > 
> 
> Here is the clk_summary relative to ethernet on Odroid-C1+
> with this new series applied:
> 
> xtal				    1            1    24000000          0 0
>  sys_pll			    0            0  1200000000          0 0
>   cpu_clk			    0            0  1200000000          0 0
>  vid_pll			    0            0   732000000          0 0
>  fixed_pll			    2            2  2550000000          0 0
>   mpll2				    1            1   249999701          0 0
>    c9410000.ethernet#m250_sel       1            1   249999701          0 0
>     c9410000.ethernet#m250_div	    1            1   249999701          0 0
>      c9410000.ethernet#fixed_div10  1            1    24999970          0 0
>       c9410000.ethernet#m25_en	    1            1    24999970          0 0
> 
> The ethernet prg0 register is set to 0x74A1 which should be correct with
> respect to the information contained in the S805 SoC manual.
> Actually, the ethernet is not yet fully functional.
> Trying to ping the board, I can see ARP request from host to board using
> tcpdump. However, the host can't see any response.

If the rx path is ok-ish, I suppose the clock setting applied is good.
Maybe you could try to play with the tx delay (BIT 5-6 of the register) ?

> 
> Following the U-Boot value for prg0 register, which is 0x7d21, I also
> tried to set bit 11. As expected, this did not have any influence.
> Another thing that we should check is the "Ethernet Memory PD" (see S805
> manual - sec. 5.4) register which bits 3-2 enable/disable ethernet
> normal operation. However, those bits are already cleared by U-Boot.
> 
> Thank you for the support.
> 
> Best regards,
> 
> Emiliano
> 
> > 
> > [0] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005596.html
> > [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005848.html
> > [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005861.html
> > 
> > 
> > Martin Blumenstingl (5):
> >   net: stmmac: dwmac-meson8b: only configure the clocks in RGMII mode
> >   net: stmmac: dwmac-meson8b: simplify generating the clock names
> >   net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration
> >   net: stmmac: dwmac-meson8b: fix setting the RGMII clock on Meson8b
> >   net: stmmac: dwmac-meson8b: propagate rate changes to the parent clock
> > 
> >  .../net/ethernet/stmicro/stmmac/dwmac-meson8b.c    | 119 +++++++++++----------
> >  1 file changed, 63 insertions(+), 56 deletions(-)
> > 
> > -- 
> > 2.15.1
> >