[PATCH net-next 0/4] net: dsa: mv88e6xxx: Support more SERDES interfacxes

[PATCH net-next 0/4] net: dsa: mv88e6xxx: Support more SERDES interfacxes

[Andrew Lunn]

Currently the SERDES interfaces for ports 9 and 10 on the mv88e6390x
are supported, allowing upto 10G. However, when unused, these SERDES
interfaces can be used by some of the lower ports for 1000Base-X.

The tricky bit here is ordering. The SERDES have to become free from
ports 9 or 10 before they can be used with lower ports. Normally, this
would happen only when these ports would be configured up, which is
too late. So at probe time, defaulting ports 9 and 10 to 1000BaseX
frees them for use with lower ports. If they are actually needed, they
will be taken back when port 9 and 10 goes up.

Andrew Lunn (4):
  net: dsa: mv88e6xxx: Group cmode ops together
  net: dsa: mv88e6xxx: Differentiate between 6390 and 6390X cmodes
  net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX
  net: dsa: mv88e6xxx: Add support for SERDES on ports 2-8 for 6390X

 drivers/net/dsa/mv88e6xxx/chip.c   | 17 ++++++++++-------
 drivers/net/dsa/mv88e6xxx/port.c   | 24 +++++++++++++++++++++---
 drivers/net/dsa/mv88e6xxx/port.h   |  2 ++
 drivers/net/dsa/mv88e6xxx/serdes.c | 26 +++++++++++++++++++-------
 drivers/net/dsa/mv88e6xxx/serdes.h |  2 ++
 5 files changed, 54 insertions(+), 17 deletions(-)

-- 
2.19.1

[PATCH net-next 1/4] net: dsa: mv88e6xxx: Group cmode ops together

[Andrew Lunn]

Move .port_set_cmode next to .port_get_cmode.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/dsa/mv88e6xxx/chip.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index e05d4eddc935..13c6d76d9150 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -3405,11 +3405,11 @@ static const struct mv88e6xxx_ops mv88e6290_ops = {
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
 	.port_set_ether_type = mv88e6351_port_set_ether_type,
 	.port_pause_limit = mv88e6390_port_pause_limit,
-	.port_set_cmode = mv88e6390x_port_set_cmode,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
 	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
+	.port_set_cmode = mv88e6390x_port_set_cmode,
 	.stats_snapshot = mv88e6390_g1_stats_snapshot,
 	.stats_set_histogram = mv88e6390_g1_stats_set_histogram,
 	.stats_get_sset_count = mv88e6320_stats_get_sset_count,
@@ -3710,11 +3710,11 @@ static const struct mv88e6xxx_ops mv88e6390_ops = {
 	.port_set_jumbo_size = mv88e6165_port_set_jumbo_size,
 	.port_egress_rate_limiting = mv88e6097_port_egress_rate_limiting,
 	.port_pause_limit = mv88e6390_port_pause_limit,
-	.port_set_cmode = mv88e6390x_port_set_cmode,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
 	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
+	.port_set_cmode = mv88e6390x_port_set_cmode,
 	.stats_snapshot = mv88e6390_g1_stats_snapshot,
 	.stats_set_histogram = mv88e6390_g1_stats_set_histogram,
 	.stats_get_sset_count = mv88e6320_stats_get_sset_count,
@@ -3757,11 +3757,11 @@ static const struct mv88e6xxx_ops mv88e6390x_ops = {
 	.port_set_jumbo_size = mv88e6165_port_set_jumbo_size,
 	.port_egress_rate_limiting = mv88e6097_port_egress_rate_limiting,
 	.port_pause_limit = mv88e6390_port_pause_limit,
-	.port_set_cmode = mv88e6390x_port_set_cmode,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
 	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
+	.port_set_cmode = mv88e6390x_port_set_cmode,
 	.stats_snapshot = mv88e6390_g1_stats_snapshot,
 	.stats_set_histogram = mv88e6390_g1_stats_set_histogram,
 	.stats_get_sset_count = mv88e6320_stats_get_sset_count,
-- 
2.19.1

[PATCH net-next 2/4] net: dsa: mv88e6xxx: Differentiate between 6390 and 6390X cmodes

[Andrew Lunn]

The X family variants support additional ports modes, for 10G
operation, which the non-X variants don't have. Add a port_set_cmode()
for non-X variants to enforce this.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/dsa/mv88e6xxx/chip.c |  7 +++++--
 drivers/net/dsa/mv88e6xxx/port.c | 15 +++++++++++++++
 drivers/net/dsa/mv88e6xxx/port.h |  2 ++
 3 files changed, 22 insertions(+), 2 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index 13c6d76d9150..733bb137efbf 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -3234,6 +3234,7 @@ static const struct mv88e6xxx_ops mv88e6190_ops = {
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
 	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
+	.port_set_cmode = mv88e6390_port_set_cmode,
 	.stats_snapshot = mv88e6390_g1_stats_snapshot,
 	.stats_set_histogram = mv88e6390_g1_stats_set_histogram,
 	.stats_get_sset_count = mv88e6320_stats_get_sset_count,
@@ -3276,6 +3277,7 @@ static const struct mv88e6xxx_ops mv88e6190x_ops = {
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
 	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
+	.port_set_cmode = mv88e6390x_port_set_cmode,
 	.stats_snapshot = mv88e6390_g1_stats_snapshot,
 	.stats_set_histogram = mv88e6390_g1_stats_set_histogram,
 	.stats_get_sset_count = mv88e6320_stats_get_sset_count,
@@ -3318,6 +3320,7 @@ static const struct mv88e6xxx_ops mv88e6191_ops = {
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
 	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
+	.port_set_cmode = mv88e6390_port_set_cmode,
 	.stats_snapshot = mv88e6390_g1_stats_snapshot,
 	.stats_set_histogram = mv88e6390_g1_stats_set_histogram,
 	.stats_get_sset_count = mv88e6320_stats_get_sset_count,
@@ -3409,7 +3412,7 @@ static const struct mv88e6xxx_ops mv88e6290_ops = {
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
 	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
-	.port_set_cmode = mv88e6390x_port_set_cmode,
+	.port_set_cmode = mv88e6390_port_set_cmode,
 	.stats_snapshot = mv88e6390_g1_stats_snapshot,
 	.stats_set_histogram = mv88e6390_g1_stats_set_histogram,
 	.stats_get_sset_count = mv88e6320_stats_get_sset_count,
@@ -3714,7 +3717,7 @@ static const struct mv88e6xxx_ops mv88e6390_ops = {
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
 	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
-	.port_set_cmode = mv88e6390x_port_set_cmode,
+	.port_set_cmode = mv88e6390_port_set_cmode,
 	.stats_snapshot = mv88e6390_g1_stats_snapshot,
 	.stats_set_histogram = mv88e6390_g1_stats_set_histogram,
 	.stats_get_sset_count = mv88e6320_stats_get_sset_count,
diff --git a/drivers/net/dsa/mv88e6xxx/port.c b/drivers/net/dsa/mv88e6xxx/port.c
index cd7db60a508b..e718404a5e03 100644
--- a/drivers/net/dsa/mv88e6xxx/port.c
+++ b/drivers/net/dsa/mv88e6xxx/port.c
@@ -437,6 +437,21 @@ int mv88e6390x_port_set_cmode(struct mv88e6xxx_chip *chip, int port,
 	return 0;
 }
 
+int mv88e6390_port_set_cmode(struct mv88e6xxx_chip *chip, int port,
+			     phy_interface_t mode)
+{
+	switch (mode) {
+	case PHY_INTERFACE_MODE_XGMII:
+	case PHY_INTERFACE_MODE_XAUI:
+	case PHY_INTERFACE_MODE_RXAUI:
+		return -EINVAL;
+	default:
+		break;
+	}
+
+	return mv88e6390x_port_set_cmode(chip, port, mode);
+}
+
 int mv88e6185_port_get_cmode(struct mv88e6xxx_chip *chip, int port, u8 *cmode)
 {
 	int err;
diff --git a/drivers/net/dsa/mv88e6xxx/port.h b/drivers/net/dsa/mv88e6xxx/port.h
index 36904c9bf955..0d81866d0e4a 100644
--- a/drivers/net/dsa/mv88e6xxx/port.h
+++ b/drivers/net/dsa/mv88e6xxx/port.h
@@ -310,6 +310,8 @@ int mv88e6097_port_pause_limit(struct mv88e6xxx_chip *chip, int port, u8 in,
 			       u8 out);
 int mv88e6390_port_pause_limit(struct mv88e6xxx_chip *chip, int port, u8 in,
 			       u8 out);
+int mv88e6390_port_set_cmode(struct mv88e6xxx_chip *chip, int port,
+			     phy_interface_t mode);
 int mv88e6390x_port_set_cmode(struct mv88e6xxx_chip *chip, int port,
 			      phy_interface_t mode);
 int mv88e6185_port_get_cmode(struct mv88e6xxx_chip *chip, int port, u8 *cmode);
-- 
2.19.1

[PATCH net-next 3/4] net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX

[Andrew Lunn]

The 6390X family has 8 SERDES interfaces. This allows ports 9 and 10
to support up to 10Gbps using 4 SERDES interfaces. However, when lower
speeds are used, which need fewer SERDES interfaces, the unused SERDES
interfaces can be used by ports 2-8.

The hardware defaults to ports 9 and 10 having all 4 SERDES interfaces
assigned to them. This only gets changed when the interface is
configured after what the SFP supports has been determined, or the 10G
PHY completes auto-neg.

For hardware designs which limit ports 9 and 10 to one or two SERDES
interfaces, and place SFPs on the lower interfaces, this is too
late. Those ports with SFP should not wait until ports 9/10 are up in
order to get access to the SERDES interface. So change the default
configuration when the driver is initialised. Configure ports 9 and 10
to 1000BaseX, so they use a single SERDES interface, freeing up the
others. They can steal them back if they need them.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/dsa/mv88e6xxx/port.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/port.c b/drivers/net/dsa/mv88e6xxx/port.c
index e718404a5e03..ebd26b6a93e6 100644
--- a/drivers/net/dsa/mv88e6xxx/port.c
+++ b/drivers/net/dsa/mv88e6xxx/port.c
@@ -368,12 +368,15 @@ int mv88e6390x_port_set_cmode(struct mv88e6xxx_chip *chip, int port,
 	u16 reg;
 	int err;
 
-	if (mode == PHY_INTERFACE_MODE_NA)
-		return 0;
-
 	if (port != 9 && port != 10)
 		return -EOPNOTSUPP;
 
+	/* Default to a slow mode, so freeing up SERDES interfaces for
+	 * other ports which might use them for SFPs.
+	 */
+	if (mode == PHY_INTERFACE_MODE_NA)
+		mode = PHY_INTERFACE_MODE_1000BASEX;
+
 	switch (mode) {
 	case PHY_INTERFACE_MODE_1000BASEX:
 		cmode = MV88E6XXX_PORT_STS_CMODE_1000BASE_X;
-- 
2.19.1

[PATCH net-next 4/4] net: dsa: mv88e6xxx: Add support for SERDES on ports 2-8 for 6390X

[Andrew Lunn]

The 6390X family has 8 SERDES interfaces. When ports 9 and 10 are not
using all their SERDES interfaces, the unused ones can be assigned to
ports 2-8. Add support for interrupts from SERDES interfaces connected
to these lower ports.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/dsa/mv88e6xxx/chip.c   |  8 ++++----
 drivers/net/dsa/mv88e6xxx/serdes.c | 26 +++++++++++++++++++-------
 drivers/net/dsa/mv88e6xxx/serdes.h |  2 ++
 3 files changed, 25 insertions(+), 11 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index 733bb137efbf..fc0f508879d4 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -3293,8 +3293,8 @@ static const struct mv88e6xxx_ops mv88e6190x_ops = {
 	.vtu_getnext = mv88e6390_g1_vtu_getnext,
 	.vtu_loadpurge = mv88e6390_g1_vtu_loadpurge,
 	.serdes_power = mv88e6390x_serdes_power,
-	.serdes_irq_setup = mv88e6390_serdes_irq_setup,
-	.serdes_irq_free = mv88e6390_serdes_irq_free,
+	.serdes_irq_setup = mv88e6390x_serdes_irq_setup,
+	.serdes_irq_free = mv88e6390x_serdes_irq_free,
 	.gpio_ops = &mv88e6352_gpio_ops,
 	.phylink_validate = mv88e6390x_phylink_validate,
 };
@@ -3780,8 +3780,8 @@ static const struct mv88e6xxx_ops mv88e6390x_ops = {
 	.vtu_getnext = mv88e6390_g1_vtu_getnext,
 	.vtu_loadpurge = mv88e6390_g1_vtu_loadpurge,
 	.serdes_power = mv88e6390x_serdes_power,
-	.serdes_irq_setup = mv88e6390_serdes_irq_setup,
-	.serdes_irq_free = mv88e6390_serdes_irq_free,
+	.serdes_irq_setup = mv88e6390x_serdes_irq_setup,
+	.serdes_irq_free = mv88e6390x_serdes_irq_free,
 	.gpio_ops = &mv88e6352_gpio_ops,
 	.avb_ops = &mv88e6390_avb_ops,
 	.ptp_ops = &mv88e6352_ptp_ops,
diff --git a/drivers/net/dsa/mv88e6xxx/serdes.c b/drivers/net/dsa/mv88e6xxx/serdes.c
index bb69650ff772..2caa8c8b4b55 100644
--- a/drivers/net/dsa/mv88e6xxx/serdes.c
+++ b/drivers/net/dsa/mv88e6xxx/serdes.c
@@ -619,15 +619,11 @@ static irqreturn_t mv88e6390_serdes_thread_fn(int irq, void *dev_id)
 	return ret;
 }
 
-int mv88e6390_serdes_irq_setup(struct mv88e6xxx_chip *chip, int port)
+int mv88e6390x_serdes_irq_setup(struct mv88e6xxx_chip *chip, int port)
 {
 	int lane;
 	int err;
 
-	/* Only support ports 9 and 10 at the moment */
-	if (port < 9)
-		return 0;
-
 	lane = mv88e6390x_serdes_get_lane(chip, port);
 
 	if (lane == -ENODEV)
@@ -663,11 +659,19 @@ int mv88e6390_serdes_irq_setup(struct mv88e6xxx_chip *chip, int port)
 	return mv88e6390_serdes_irq_enable(chip, port, lane);
 }
 
-void mv88e6390_serdes_irq_free(struct mv88e6xxx_chip *chip, int port)
+int mv88e6390_serdes_irq_setup(struct mv88e6xxx_chip *chip, int port)
+{
+	if (port < 9)
+		return 0;
+
+	return mv88e6390_serdes_irq_setup(chip, port);
+}
+
+void mv88e6390x_serdes_irq_free(struct mv88e6xxx_chip *chip, int port)
 {
 	int lane = mv88e6390x_serdes_get_lane(chip, port);
 
-	if (port < 9)
+	if (lane == -ENODEV)
 		return;
 
 	if (lane < 0)
@@ -685,6 +689,14 @@ void mv88e6390_serdes_irq_free(struct mv88e6xxx_chip *chip, int port)
 	chip->ports[port].serdes_irq = 0;
 }
 
+void mv88e6390_serdes_irq_free(struct mv88e6xxx_chip *chip, int port)
+{
+	if (port < 9)
+		return;
+
+	mv88e6390x_serdes_irq_free(chip, port);
+}
+
 int mv88e6341_serdes_power(struct mv88e6xxx_chip *chip, int port, bool on)
 {
 	u8 cmode = chip->ports[port].cmode;
diff --git a/drivers/net/dsa/mv88e6xxx/serdes.h b/drivers/net/dsa/mv88e6xxx/serdes.h
index 7870c5a9ef12..573dce8b1eb4 100644
--- a/drivers/net/dsa/mv88e6xxx/serdes.h
+++ b/drivers/net/dsa/mv88e6xxx/serdes.h
@@ -77,6 +77,8 @@ int mv88e6390_serdes_power(struct mv88e6xxx_chip *chip, int port, bool on);
 int mv88e6390x_serdes_power(struct mv88e6xxx_chip *chip, int port, bool on);
 int mv88e6390_serdes_irq_setup(struct mv88e6xxx_chip *chip, int port);
 void mv88e6390_serdes_irq_free(struct mv88e6xxx_chip *chip, int port);
+int mv88e6390x_serdes_irq_setup(struct mv88e6xxx_chip *chip, int port);
+void mv88e6390x_serdes_irq_free(struct mv88e6xxx_chip *chip, int port);
 int mv88e6352_serdes_get_sset_count(struct mv88e6xxx_chip *chip, int port);
 int mv88e6352_serdes_get_strings(struct mv88e6xxx_chip *chip,
 				 int port, uint8_t *data);
-- 
2.19.1

Re: [PATCH net-next 0/4] net: dsa: mv88e6xxx: Support more SERDES interfacxes

[David Miller]

From: Andrew Lunn <andrew@lunn.ch>
Date: Sun, 11 Nov 2018 00:32:13 +0100

> Currently the SERDES interfaces for ports 9 and 10 on the mv88e6390x
> are supported, allowing upto 10G. However, when unused, these SERDES
> interfaces can be used by some of the lower ports for 1000Base-X.
> 
> The tricky bit here is ordering. The SERDES have to become free from
> ports 9 or 10 before they can be used with lower ports. Normally, this
> would happen only when these ports would be configured up, which is
> too late. So at probe time, defaulting ports 9 and 10 to 1000BaseX
> frees them for use with lower ports. If they are actually needed, they
> will be taken back when port 9 and 10 goes up.

Series applied, thanks Andrew.