[PATCH net V5 0/3] net: lan743x: Fixes for multiple WOL related issues

[PATCH net V5 0/3] net: lan743x: Fixes for multiple WOL related issues

[Raju Lakkaraju]

This patch series implement the following fixes:
1. Disable WOL upon resume in order to restore full data path operation
2. Support WOL at both the PHY and MAC appropriately 
3. Remove interrupt mask clearing from config_init 

Patch-3 was sent seperately earlier. Review comments in link: 
https://lore.kernel.org/lkml/4a565d54-f468-4e32-8a2c-102c1203f72c@lunn.ch/T/

Raju Lakkaraju (3):
  net: lan743x: disable WOL upon resume to restore full data path
    operation
  net: lan743x: Support WOL at both the PHY and MAC appropriately
  net: phy: mxl-gpy: Remove interrupt mask clearing from config_init

 .../net/ethernet/microchip/lan743x_ethtool.c  | 44 ++++++++++++--
 drivers/net/ethernet/microchip/lan743x_main.c | 48 ++++++++++++---
 drivers/net/ethernet/microchip/lan743x_main.h | 28 +++++++++
 drivers/net/phy/mxl-gpy.c                     | 58 ++++++++++++-------
 4 files changed, 146 insertions(+), 32 deletions(-)

-- 
2.34.1

[PATCH net V5 1/3] net: lan743x: disable WOL upon resume to restore full data path operation

[Raju Lakkaraju]

When Wake-on-LAN (WoL) is active and the system is in suspend mode, triggering
a system event can wake the system from sleep, which may block the data path.
To restore normal data path functionality after waking, disable all wake-up
events. Furthermore, clear all Write 1 to Clear (W1C) status bits by writing
1's to them.

Fixes: 4d94282afd95 ("lan743x: Add power management support")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
---
Change List:
------------
V4 -> V5:
  - Change Wakeup source message from info to debug
V3 -> V4:
  - No change
V2 -> V3:
  - No change
V1 -> V2:
  - Repost - No change
V0 -> V1:
  - Variable "data" change from "int" to "unsigned int"
 drivers/net/ethernet/microchip/lan743x_main.c | 30 ++++++++++++++++---
 drivers/net/ethernet/microchip/lan743x_main.h | 24 +++++++++++++++
 2 files changed, 50 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/microchip/lan743x_main.c b/drivers/net/ethernet/microchip/lan743x_main.c
index 6be8a43c908a..48835bdc2e63 100644
--- a/drivers/net/ethernet/microchip/lan743x_main.c
+++ b/drivers/net/ethernet/microchip/lan743x_main.c
@@ -3575,7 +3575,7 @@ static void lan743x_pm_set_wol(struct lan743x_adapter *adapter)
 
 	/* clear wake settings */
 	pmtctl = lan743x_csr_read(adapter, PMT_CTL);
-	pmtctl |= PMT_CTL_WUPS_MASK_;
+	pmtctl |= PMT_CTL_WUPS_MASK_ | PMT_CTL_RES_CLR_WKP_MASK_;
 	pmtctl &= ~(PMT_CTL_GPIO_WAKEUP_EN_ | PMT_CTL_EEE_WAKEUP_EN_ |
 		PMT_CTL_WOL_EN_ | PMT_CTL_MAC_D3_RX_CLK_OVR_ |
 		PMT_CTL_RX_FCT_RFE_D3_CLK_OVR_ | PMT_CTL_ETH_PHY_WAKE_EN_);
@@ -3710,6 +3710,7 @@ static int lan743x_pm_resume(struct device *dev)
 	struct pci_dev *pdev = to_pci_dev(dev);
 	struct net_device *netdev = pci_get_drvdata(pdev);
 	struct lan743x_adapter *adapter = netdev_priv(netdev);
+	u32 data;
 	int ret;
 
 	pci_set_power_state(pdev, PCI_D0);
@@ -3728,6 +3729,30 @@ static int lan743x_pm_resume(struct device *dev)
 		return ret;
 	}
 
+	ret = lan743x_csr_read(adapter, MAC_WK_SRC);
+	netif_dbg(adapter, drv, adapter->netdev,
+		  "Wakeup source : 0x%08X\n", ret);
+
+	/* Clear the wol configuration and status bits. Note that
+	 * the status bits are "Write One to Clear (W1C)"
+	 */
+	data = MAC_WUCSR_EEE_TX_WAKE_ | MAC_WUCSR_EEE_RX_WAKE_ |
+	       MAC_WUCSR_RFE_WAKE_FR_ | MAC_WUCSR_PFDA_FR_ | MAC_WUCSR_WUFR_ |
+	       MAC_WUCSR_MPR_ | MAC_WUCSR_BCAST_FR_;
+	lan743x_csr_write(adapter, MAC_WUCSR, data);
+
+	data = MAC_WUCSR2_NS_RCD_ | MAC_WUCSR2_ARP_RCD_ |
+	       MAC_WUCSR2_IPV6_TCPSYN_RCD_ | MAC_WUCSR2_IPV4_TCPSYN_RCD_;
+	lan743x_csr_write(adapter, MAC_WUCSR2, data);
+
+	data = MAC_WK_SRC_ETH_PHY_WK_ | MAC_WK_SRC_IPV6_TCPSYN_RCD_WK_ |
+	       MAC_WK_SRC_IPV4_TCPSYN_RCD_WK_ | MAC_WK_SRC_EEE_TX_WK_ |
+	       MAC_WK_SRC_EEE_RX_WK_ | MAC_WK_SRC_RFE_FR_WK_ |
+	       MAC_WK_SRC_PFDA_FR_WK_ | MAC_WK_SRC_MP_FR_WK_ |
+	       MAC_WK_SRC_BCAST_FR_WK_ | MAC_WK_SRC_WU_FR_WK_ |
+	       MAC_WK_SRC_WK_FR_SAVED_;
+	lan743x_csr_write(adapter, MAC_WK_SRC, data);
+
 	/* open netdev when netdev is at running state while resume.
 	 * For instance, it is true when system wakesup after pm-suspend
 	 * However, it is false when system wakes up after suspend GUI menu
@@ -3736,9 +3761,6 @@ static int lan743x_pm_resume(struct device *dev)
 		lan743x_netdev_open(netdev);
 
 	netif_device_attach(netdev);
-	ret = lan743x_csr_read(adapter, MAC_WK_SRC);
-	netif_info(adapter, drv, adapter->netdev,
-		   "Wakeup source : 0x%08X\n", ret);
 
 	return 0;
 }
diff --git a/drivers/net/ethernet/microchip/lan743x_main.h b/drivers/net/ethernet/microchip/lan743x_main.h
index 645bc048e52e..fac0f33d10b2 100644
--- a/drivers/net/ethernet/microchip/lan743x_main.h
+++ b/drivers/net/ethernet/microchip/lan743x_main.h
@@ -61,6 +61,7 @@
 #define PMT_CTL_RX_FCT_RFE_D3_CLK_OVR_		BIT(18)
 #define PMT_CTL_GPIO_WAKEUP_EN_			BIT(15)
 #define PMT_CTL_EEE_WAKEUP_EN_			BIT(13)
+#define PMT_CTL_RES_CLR_WKP_MASK_		GENMASK(9, 8)
 #define PMT_CTL_READY_				BIT(7)
 #define PMT_CTL_ETH_PHY_RST_			BIT(4)
 #define PMT_CTL_WOL_EN_				BIT(3)
@@ -227,12 +228,31 @@
 #define MAC_WUCSR				(0x140)
 #define MAC_MP_SO_EN_				BIT(21)
 #define MAC_WUCSR_RFE_WAKE_EN_			BIT(14)
+#define MAC_WUCSR_EEE_TX_WAKE_			BIT(13)
+#define MAC_WUCSR_EEE_RX_WAKE_			BIT(11)
+#define MAC_WUCSR_RFE_WAKE_FR_			BIT(9)
+#define MAC_WUCSR_PFDA_FR_			BIT(7)
+#define MAC_WUCSR_WUFR_				BIT(6)
+#define MAC_WUCSR_MPR_				BIT(5)
+#define MAC_WUCSR_BCAST_FR_			BIT(4)
 #define MAC_WUCSR_PFDA_EN_			BIT(3)
 #define MAC_WUCSR_WAKE_EN_			BIT(2)
 #define MAC_WUCSR_MPEN_				BIT(1)
 #define MAC_WUCSR_BCST_EN_			BIT(0)
 
 #define MAC_WK_SRC				(0x144)
+#define MAC_WK_SRC_ETH_PHY_WK_			BIT(17)
+#define MAC_WK_SRC_IPV6_TCPSYN_RCD_WK_		BIT(16)
+#define MAC_WK_SRC_IPV4_TCPSYN_RCD_WK_		BIT(15)
+#define MAC_WK_SRC_EEE_TX_WK_			BIT(14)
+#define MAC_WK_SRC_EEE_RX_WK_			BIT(13)
+#define MAC_WK_SRC_RFE_FR_WK_			BIT(12)
+#define MAC_WK_SRC_PFDA_FR_WK_			BIT(11)
+#define MAC_WK_SRC_MP_FR_WK_			BIT(10)
+#define MAC_WK_SRC_BCAST_FR_WK_			BIT(9)
+#define MAC_WK_SRC_WU_FR_WK_			BIT(8)
+#define MAC_WK_SRC_WK_FR_SAVED_			BIT(7)
+
 #define MAC_MP_SO_HI				(0x148)
 #define MAC_MP_SO_LO				(0x14C)
 
@@ -295,6 +315,10 @@
 #define RFE_INDX(index)			(0x580 + (index << 2))
 
 #define MAC_WUCSR2			(0x600)
+#define MAC_WUCSR2_NS_RCD_		BIT(7)
+#define MAC_WUCSR2_ARP_RCD_		BIT(6)
+#define MAC_WUCSR2_IPV6_TCPSYN_RCD_	BIT(5)
+#define MAC_WUCSR2_IPV4_TCPSYN_RCD_	BIT(4)
 
 #define SGMII_ACC			(0x720)
 #define SGMII_ACC_SGMII_BZY_		BIT(31)
-- 
2.34.1

[PATCH net V5 2/3] net: lan743x: Support WOL at both the PHY and MAC appropriately

[Raju Lakkaraju]

Prevent options not supported by the PHY from being requested to it by the MAC
Whenever a WOL option is supported by both, the PHY is given priority
since that usually leads to better power savings.

Fixes: e9e13b6adc33 ("lan743x: fix for potential NULL pointer dereference with bare card")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
---
Change List:
------------
V4 -> V5:
  - Change Fixes's SHA from 13 chars to 12 chars
  - Remove the "Reported-by" and "Closes" tags
V3 -> V4:
  - Fix the support for "CONFIG_PM=N" 
V2 -> V3:
  - Remove the "phy does not support WOL" debug message which is not required
  - Remove WAKE_PHY support option from Ethernet MAC (LAN743x/PCI11x1x) driver
  - Add "phy_wol_supported" and "phy_wolopts" variables to hold PHY's WOL config
V1 -> V2:
  - Repost - No change
V0 -> V1:
  - Change the "phy does not support WOL" print from netif_info() to
    netif_dbg()

 .../net/ethernet/microchip/lan743x_ethtool.c  | 44 +++++++++++++++++--
 drivers/net/ethernet/microchip/lan743x_main.c | 18 ++++++--
 drivers/net/ethernet/microchip/lan743x_main.h |  4 ++
 3 files changed, 58 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/microchip/lan743x_ethtool.c b/drivers/net/ethernet/microchip/lan743x_ethtool.c
index d0f4ff4ee075..0d1740d64676 100644
--- a/drivers/net/ethernet/microchip/lan743x_ethtool.c
+++ b/drivers/net/ethernet/microchip/lan743x_ethtool.c
@@ -1127,8 +1127,12 @@ static void lan743x_ethtool_get_wol(struct net_device *netdev,
 	if (netdev->phydev)
 		phy_ethtool_get_wol(netdev->phydev, wol);
 
-	wol->supported |= WAKE_BCAST | WAKE_UCAST | WAKE_MCAST |
-		WAKE_MAGIC | WAKE_PHY | WAKE_ARP;
+	if (wol->supported != adapter->phy_wol_supported)
+		netif_warn(adapter, drv, adapter->netdev,
+			   "PHY changed its supported WOL! old=%x, new=%x\n",
+			   adapter->phy_wol_supported, wol->supported);
+
+	wol->supported |= MAC_SUPPORTED_WAKES;
 
 	if (adapter->is_pci11x1x)
 		wol->supported |= WAKE_MAGICSECURE;
@@ -1143,7 +1147,39 @@ static int lan743x_ethtool_set_wol(struct net_device *netdev,
 {
 	struct lan743x_adapter *adapter = netdev_priv(netdev);
 
+	/* WAKE_MAGICSEGURE is a modifier of and only valid together with
+	 * WAKE_MAGIC
+	 */
+	if ((wol->wolopts & WAKE_MAGICSECURE) && !(wol->wolopts & WAKE_MAGIC))
+		return -EINVAL;
+
+	if (netdev->phydev) {
+		struct ethtool_wolinfo phy_wol;
+		int ret;
+
+		phy_wol.wolopts = wol->wolopts & adapter->phy_wol_supported;
+
+		/* If WAKE_MAGICSECURE was requested, filter out WAKE_MAGIC
+		 * for PHYs that do not support WAKE_MAGICSECURE
+		 */
+		if (wol->wolopts & WAKE_MAGICSECURE &&
+		    !(adapter->phy_wol_supported & WAKE_MAGICSECURE))
+			phy_wol.wolopts &= ~WAKE_MAGIC;
+
+		ret = phy_ethtool_set_wol(netdev->phydev, &phy_wol);
+		if (ret && (ret != -EOPNOTSUPP))
+			return ret;
+
+		if (ret == -EOPNOTSUPP)
+			adapter->phy_wolopts = 0;
+		else
+			adapter->phy_wolopts = phy_wol.wolopts;
+	} else {
+		adapter->phy_wolopts = 0;
+	}
+
 	adapter->wolopts = 0;
+	wol->wolopts &= ~adapter->phy_wolopts;
 	if (wol->wolopts & WAKE_UCAST)
 		adapter->wolopts |= WAKE_UCAST;
 	if (wol->wolopts & WAKE_MCAST)
@@ -1164,10 +1200,10 @@ static int lan743x_ethtool_set_wol(struct net_device *netdev,
 		memset(adapter->sopass, 0, sizeof(u8) * SOPASS_MAX);
 	}
 
+	wol->wolopts = adapter->wolopts | adapter->phy_wolopts;
 	device_set_wakeup_enable(&adapter->pdev->dev, (bool)wol->wolopts);
 
-	return netdev->phydev ? phy_ethtool_set_wol(netdev->phydev, wol)
-			: -ENETDOWN;
+	return 0;
 }
 #endif /* CONFIG_PM */
 
diff --git a/drivers/net/ethernet/microchip/lan743x_main.c b/drivers/net/ethernet/microchip/lan743x_main.c
index 48835bdc2e63..e418539565b1 100644
--- a/drivers/net/ethernet/microchip/lan743x_main.c
+++ b/drivers/net/ethernet/microchip/lan743x_main.c
@@ -3118,6 +3118,17 @@ static int lan743x_netdev_open(struct net_device *netdev)
 		if (ret)
 			goto close_tx;
 	}
+
+#ifdef CONFIG_PM
+	if (adapter->netdev->phydev) {
+		struct ethtool_wolinfo wol = { .cmd = ETHTOOL_GWOL };
+
+		phy_ethtool_get_wol(netdev->phydev, &wol);
+		adapter->phy_wol_supported = wol.supported;
+		adapter->phy_wolopts = wol.wolopts;
+	}
+#endif
+
 	return 0;
 
 close_tx:
@@ -3587,10 +3598,9 @@ static void lan743x_pm_set_wol(struct lan743x_adapter *adapter)
 
 	pmtctl |= PMT_CTL_ETH_PHY_D3_COLD_OVR_ | PMT_CTL_ETH_PHY_D3_OVR_;
 
-	if (adapter->wolopts & WAKE_PHY) {
-		pmtctl |= PMT_CTL_ETH_PHY_EDPD_PLL_CTL_;
+	if (adapter->phy_wolopts)
 		pmtctl |= PMT_CTL_ETH_PHY_WAKE_EN_;
-	}
+
 	if (adapter->wolopts & WAKE_MAGIC) {
 		wucsr |= MAC_WUCSR_MPEN_;
 		macrx |= MAC_RX_RXEN_;
@@ -3686,7 +3696,7 @@ static int lan743x_pm_suspend(struct device *dev)
 	lan743x_csr_write(adapter, MAC_WUCSR2, 0);
 	lan743x_csr_write(adapter, MAC_WK_SRC, 0xFFFFFFFF);
 
-	if (adapter->wolopts)
+	if (adapter->wolopts || adapter->phy_wolopts)
 		lan743x_pm_set_wol(adapter);
 
 	if (adapter->is_pci11x1x) {
diff --git a/drivers/net/ethernet/microchip/lan743x_main.h b/drivers/net/ethernet/microchip/lan743x_main.h
index fac0f33d10b2..3b2585a384e2 100644
--- a/drivers/net/ethernet/microchip/lan743x_main.h
+++ b/drivers/net/ethernet/microchip/lan743x_main.h
@@ -1042,6 +1042,8 @@ enum lan743x_sgmii_lsd {
 	LINK_2500_SLAVE
 };
 
+#define MAC_SUPPORTED_WAKES  (WAKE_BCAST | WAKE_UCAST | WAKE_MCAST | \
+			      WAKE_MAGIC | WAKE_ARP)
 struct lan743x_adapter {
 	struct net_device       *netdev;
 	struct mii_bus		*mdiobus;
@@ -1049,6 +1051,8 @@ struct lan743x_adapter {
 #ifdef CONFIG_PM
 	u32			wolopts;
 	u8			sopass[SOPASS_MAX];
+	u32			phy_wolopts;
+	u32			phy_wol_supported;
 #endif
 	struct pci_dev		*pdev;
 	struct lan743x_csr      csr;
-- 
2.34.1

[PATCH net V5 3/3] net: phy: mxl-gpy: Remove interrupt mask clearing from config_init

[Raju Lakkaraju]

When the system resumes from sleep, the phy_init_hw() function invokes
config_init(), which clears all interrupt masks and causes wake events to be
lost in subsequent wake sequences. Remove interrupt mask clearing from
config_init() and preserve relevant masks in config_intr().

Fixes: 7d901a1e878a ("net: phy: add Maxlinear GPY115/21x/24x driver")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
---
Change List:
------------
V4 -> V5:
  - No change
V3 -> V4:
  - No change
V0 -> V3:
  - Address the https://lore.kernel.org/lkml/4a565d54-f468-4e32-8a2c-102c1203f72c@lunn.ch/T/
    review comments

 drivers/net/phy/mxl-gpy.c | 58 +++++++++++++++++++++++++--------------
 1 file changed, 38 insertions(+), 20 deletions(-)

diff --git a/drivers/net/phy/mxl-gpy.c b/drivers/net/phy/mxl-gpy.c
index b2d36a3a96f1..e5f8ac4b4604 100644
--- a/drivers/net/phy/mxl-gpy.c
+++ b/drivers/net/phy/mxl-gpy.c
@@ -107,6 +107,7 @@ struct gpy_priv {
 
 	u8 fw_major;
 	u8 fw_minor;
+	u32 wolopts;
 
 	/* It takes 3 seconds to fully switch out of loopback mode before
 	 * it can safely re-enter loopback mode. Record the time when
@@ -221,6 +222,15 @@ static int gpy_hwmon_register(struct phy_device *phydev)
 }
 #endif
 
+static int gpy_ack_interrupt(struct phy_device *phydev)
+{
+	int ret;
+
+	/* Clear all pending interrupts */
+	ret = phy_read(phydev, PHY_ISTAT);
+	return ret < 0 ? ret : 0;
+}
+
 static int gpy_mbox_read(struct phy_device *phydev, u32 addr)
 {
 	struct gpy_priv *priv = phydev->priv;
@@ -262,16 +272,8 @@ static int gpy_mbox_read(struct phy_device *phydev, u32 addr)
 
 static int gpy_config_init(struct phy_device *phydev)
 {
-	int ret;
-
-	/* Mask all interrupts */
-	ret = phy_write(phydev, PHY_IMASK, 0);
-	if (ret)
-		return ret;
-
-	/* Clear all pending interrupts */
-	ret = phy_read(phydev, PHY_ISTAT);
-	return ret < 0 ? ret : 0;
+	/* Nothing to configure. Configuration Requirement Placeholder */
+	return 0;
 }
 
 static int gpy21x_config_init(struct phy_device *phydev)
@@ -627,11 +629,23 @@ static int gpy_read_status(struct phy_device *phydev)
 
 static int gpy_config_intr(struct phy_device *phydev)
 {
+	struct gpy_priv *priv = phydev->priv;
 	u16 mask = 0;
+	int ret;
+
+	ret = gpy_ack_interrupt(phydev);
+	if (ret)
+		return ret;
 
 	if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
 		mask = PHY_IMASK_MASK;
 
+	if (priv->wolopts & WAKE_MAGIC)
+		mask |= PHY_IMASK_WOL;
+
+	if (priv->wolopts & WAKE_PHY)
+		mask |= PHY_IMASK_LSTC;
+
 	return phy_write(phydev, PHY_IMASK, mask);
 }
 
@@ -678,6 +692,7 @@ static int gpy_set_wol(struct phy_device *phydev,
 		       struct ethtool_wolinfo *wol)
 {
 	struct net_device *attach_dev = phydev->attached_dev;
+	struct gpy_priv *priv = phydev->priv;
 	int ret;
 
 	if (wol->wolopts & WAKE_MAGIC) {
@@ -725,6 +740,8 @@ static int gpy_set_wol(struct phy_device *phydev,
 		ret = phy_read(phydev, PHY_ISTAT);
 		if (ret < 0)
 			return ret;
+
+		priv->wolopts |= WAKE_MAGIC;
 	} else {
 		/* Disable magic packet matching */
 		ret = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2,
@@ -732,6 +749,13 @@ static int gpy_set_wol(struct phy_device *phydev,
 					 WOL_EN);
 		if (ret < 0)
 			return ret;
+
+		/* Disable the WOL interrupt */
+		ret = phy_clear_bits(phydev, PHY_IMASK, PHY_IMASK_WOL);
+		if (ret < 0)
+			return ret;
+
+		priv->wolopts &= ~WAKE_MAGIC;
 	}
 
 	if (wol->wolopts & WAKE_PHY) {
@@ -748,9 +772,11 @@ static int gpy_set_wol(struct phy_device *phydev,
 		if (ret & (PHY_IMASK_MASK & ~PHY_IMASK_LSTC))
 			phy_trigger_machine(phydev);
 
+		priv->wolopts |= WAKE_PHY;
 		return 0;
 	}
 
+	priv->wolopts &= ~WAKE_PHY;
 	/* Disable the link state change interrupt */
 	return phy_clear_bits(phydev, PHY_IMASK, PHY_IMASK_LSTC);
 }
@@ -758,18 +784,10 @@ static int gpy_set_wol(struct phy_device *phydev,
 static void gpy_get_wol(struct phy_device *phydev,
 			struct ethtool_wolinfo *wol)
 {
-	int ret;
+	struct gpy_priv *priv = phydev->priv;
 
 	wol->supported = WAKE_MAGIC | WAKE_PHY;
-	wol->wolopts = 0;
-
-	ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, VPSPEC2_WOL_CTL);
-	if (ret & WOL_EN)
-		wol->wolopts |= WAKE_MAGIC;
-
-	ret = phy_read(phydev, PHY_IMASK);
-	if (ret & PHY_IMASK_LSTC)
-		wol->wolopts |= WAKE_PHY;
+	wol->wolopts = priv->wolopts;
 }
 
 static int gpy_loopback(struct phy_device *phydev, bool enable)
-- 
2.34.1

Re: [PATCH net V5 0/3] net: lan743x: Fixes for multiple WOL related issues

[patchwork-bot+netdevbpf]

Hello:

This series was applied to netdev/net.git (main)
by Paolo Abeni <pabeni@redhat.com>:

On Fri, 14 Jun 2024 22:41:54 +0530 you wrote:
> This patch series implement the following fixes:
> 1. Disable WOL upon resume in order to restore full data path operation
> 2. Support WOL at both the PHY and MAC appropriately
> 3. Remove interrupt mask clearing from config_init
> 
> Patch-3 was sent seperately earlier. Review comments in link:
> https://lore.kernel.org/lkml/4a565d54-f468-4e32-8a2c-102c1203f72c@lunn.ch/T/
> 
> [...]

Here is the summary with links:
  - [net,V5,1/3] net: lan743x: disable WOL upon resume to restore full data path operation
    https://git.kernel.org/netdev/net/c/7725363936a8
  - [net,V5,2/3] net: lan743x: Support WOL at both the PHY and MAC appropriately
    https://git.kernel.org/netdev/net/c/8c248cd83601
  - [net,V5,3/3] net: phy: mxl-gpy: Remove interrupt mask clearing from config_init
    https://git.kernel.org/netdev/net/c/c44d3ffd85db

You are awesome, thank you!
-- 
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html