[PATCH v2 0/3] net: Convert Gianfar (Triple Speed Ethernet Controller) bindings to YAML

[PATCH v2 0/3] net: Convert Gianfar (Triple Speed Ethernet Controller) bindings to YAML

[J. Neuschäfer via B4 Relay]

The aim of this series is to modernize the device tree bindings for the
Freescale "Gianfar" ethernet controller (a.k.a. TSEC, Triple Speed
Ethernet Controller) by converting them to YAML.

Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
---
Changes in v2:
- various cleanups suggested by reviewers
- use a 'select:' schema to disambiguate compatible = "gianfar" between
  network controller and MDIO nodes
- Link to v1: https://lore.kernel.org/r/20250220-gianfar-yaml-v1-0-0ba97fd1ef92@posteo.net

---
J. Neuschäfer (3):
      dt-bindings: net: Convert fsl,gianfar-{mdio,tbi} to YAML
      dt-bindings: net: fsl,gianfar-mdio: Update information about TBI
      dt-bindings: net: Convert fsl,gianfar to YAML

 .../devicetree/bindings/net/fsl,gianfar-mdio.yaml  | 112 ++++++++++
 .../devicetree/bindings/net/fsl,gianfar.yaml       | 248 +++++++++++++++++++++
 .../devicetree/bindings/net/fsl-tsec-phy.txt       |  80 +------
 3 files changed, 363 insertions(+), 77 deletions(-)
---
base-commit: 2014c95afecee3e76ca4a56956a936e23283f05b
change-id: 20250209-gianfar-yaml-a654263b7534

Best regards,
-- 
J. Neuschäfer <j.ne@posteo.net>

[PATCH v2 1/3] dt-bindings: net: Convert fsl,gianfar-{mdio,tbi} to YAML

[J. Neuschäfer via B4 Relay]

From: "J. Neuschäfer" <j.ne@posteo.net>

Move the information related to the Freescale Gianfar (TSEC) MDIO bus
and the Ten-Bit Interface (TBI) from fsl-tsec-phy.txt to a new binding
file in YAML format, fsl,gianfar-mdio.yaml.

Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
---

V2:
- remove definitions of #address/size-cells (already in mdio.yaml)
- disambiguate compatible = "gianfar" schemas by using a "select:" schema
---
 .../devicetree/bindings/net/fsl,gianfar-mdio.yaml  | 113 +++++++++++++++++++++
 .../devicetree/bindings/net/fsl-tsec-phy.txt       |  41 +-------
 2 files changed, 115 insertions(+), 39 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/fsl,gianfar-mdio.yaml b/Documentation/devicetree/bindings/net/fsl,gianfar-mdio.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..22369771c13614875845b6d6e6d6031b933cb152
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/fsl,gianfar-mdio.yaml
@@ -0,0 +1,113 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/fsl,gianfar-mdio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale Gianfar (TSEC) MDIO Device
+
+description:
+  This binding describes the MDIO is a bus to which the PHY devices are
+  connected. For each device that exists on this bus, a child node should be
+  created.
+
+  As of this writing, every TSEC is associated with an internal Ten-Bit
+  Interface (TBI) PHY. This PHY is accessed through the local MDIO bus. These
+  buses are defined similarly to the mdio buses, except they are compatible
+  with "fsl,gianfar-tbi". The TBI PHYs underneath them are similar to normal
+  PHYs, but the reg property is considered instructive, rather than
+  descriptive. The reg property should be chosen so it doesn't interfere with
+  other PHYs on the bus.
+
+maintainers:
+  - J. Neuschäfer <j.ne@posteo.net>
+
+# This is needed to distinguish gianfar.yaml and gianfar-mdio.yaml, because
+# both use compatible = "gianfar" (with different device_type values)
+select:
+  oneOf:
+    - properties:
+        compatible:
+          contains:
+            const: gianfar
+        device_type:
+          const: mdio
+      required:
+        - device_type
+
+    - properties:
+        compatible:
+          contains:
+            enum:
+              - fsl,gianfar-tbi
+              - fsl,gianfar-mdio
+              - fsl,etsec2-tbi
+              - fsl,etsec2-mdio
+              - fsl,ucc-mdio
+              - ucc_geth_phy
+
+  required:
+    - compatible
+
+properties:
+  compatible:
+    enum:
+      - fsl,gianfar-tbi
+      - fsl,gianfar-mdio
+      - fsl,etsec2-tbi
+      - fsl,etsec2-mdio
+      - fsl,ucc-mdio
+      - gianfar
+      - ucc_geth_phy
+
+  reg:
+    minItems: 1
+    items:
+      - description:
+          Offset and length of the register set for the device
+
+      - description:
+          Optionally, the offset and length of the TBIPA register (TBI PHY
+          address register). If TBIPA register is not specified, the driver
+          will attempt to infer it from the register set specified (your
+          mileage may vary).
+
+  device_type:
+    const: mdio
+
+required:
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+
+allOf:
+  - $ref: mdio.yaml#
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: ucc_geth_phy
+    then:
+      required:
+        - device_type
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    soc {
+        #address-cells = <1>;
+        #size-cells = <1>;
+
+        mdio@24520 {
+            reg = <0x24520 0x20>;
+            compatible = "fsl,gianfar-mdio";
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            ethernet-phy@0 {
+                reg = <0>;
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
index 9c9668c1b6a24edff7b7cf625b9f14c3cbc2e0c8..0e55e0af7d6f59cfb571dd3fcff704b7f4c140d2 100644
--- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
+++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
@@ -1,47 +1,10 @@
 * MDIO IO device
 
-The MDIO is a bus to which the PHY devices are connected.  For each
-device that exists on this bus, a child node should be created.  See
-the definition of the PHY node in booting-without-of.txt for an example
-of how to define a PHY.
-
-Required properties:
-  - reg : Offset and length of the register set for the device, and optionally
-          the offset and length of the TBIPA register (TBI PHY address
-	  register).  If TBIPA register is not specified, the driver will
-	  attempt to infer it from the register set specified (your mileage may
-	  vary).
-  - compatible : Should define the compatible device type for the
-    mdio. Currently supported strings/devices are:
-	- "fsl,gianfar-tbi"
-	- "fsl,gianfar-mdio"
-	- "fsl,etsec2-tbi"
-	- "fsl,etsec2-mdio"
-	- "fsl,ucc-mdio"
-	- "fsl,fman-mdio"
-    When device_type is "mdio", the following strings are also considered:
-	- "gianfar"
-	- "ucc_geth_phy"
-
-Example:
-
-	mdio@24520 {
-		reg = <24520 20>;
-		compatible = "fsl,gianfar-mdio";
-
-		ethernet-phy@0 {
-			......
-		};
-	};
+Refer to Documentation/devicetree/bindings/net/fsl,gianfar-mdio.yaml
 
 * TBI Internal MDIO bus
 
-As of this writing, every tsec is associated with an internal TBI PHY.
-This PHY is accessed through the local MDIO bus.  These buses are defined
-similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi".
-The TBI PHYs underneath them are similar to normal PHYs, but the reg property
-is considered instructive, rather than descriptive.  The reg property should
-be chosen so it doesn't interfere with other PHYs on the bus.
+Refer to Documentation/devicetree/bindings/net/fsl,gianfar-mdio.yaml
 
 * Gianfar-compatible ethernet nodes
 

-- 
2.48.0.rc1.219.gb6b6757d772

[PATCH v2 2/3] dt-bindings: net: fsl,gianfar-mdio: Update information about TBI

[J. Neuschäfer via B4 Relay]

From: "J. Neuschäfer" <j.ne@posteo.net>

When this binding was originally written, all known TSEC Ethernet
controllers had a Ten-Bit Interface (TBI). However, some datasheets such
as for the MPC8315E suggest that this is not universally true:

  The eTSECs do not support TBI, GMII, and FIFO operating modes, so all
  references to these interfaces and features should be ignored for this
  device.

Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
---

V2:
- Add Rob's Acked-by tag
---
 Documentation/devicetree/bindings/net/fsl,gianfar-mdio.yaml | 13 ++++++-------
 1 file changed, 6 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/fsl,gianfar-mdio.yaml b/Documentation/devicetree/bindings/net/fsl,gianfar-mdio.yaml
index 22369771c13614875845b6d6e6d6031b933cb152..03c819bc701be4e6bcae37891baccd4b01ec53c4 100644
--- a/Documentation/devicetree/bindings/net/fsl,gianfar-mdio.yaml
+++ b/Documentation/devicetree/bindings/net/fsl,gianfar-mdio.yaml
@@ -11,13 +11,12 @@ description:
   connected. For each device that exists on this bus, a child node should be
   created.
 
-  As of this writing, every TSEC is associated with an internal Ten-Bit
-  Interface (TBI) PHY. This PHY is accessed through the local MDIO bus. These
-  buses are defined similarly to the mdio buses, except they are compatible
-  with "fsl,gianfar-tbi". The TBI PHYs underneath them are similar to normal
-  PHYs, but the reg property is considered instructive, rather than
-  descriptive. The reg property should be chosen so it doesn't interfere with
-  other PHYs on the bus.
+  Some TSECs are associated with an internal Ten-Bit Interface (TBI) PHY. This
+  PHY is accessed through the local MDIO bus. These buses are defined similarly
+  to the mdio buses, except they are compatible with "fsl,gianfar-tbi". The TBI
+  PHYs underneath them are similar to normal PHYs, but the reg property is
+  considered instructive, rather than descriptive. The reg property should be
+  chosen so it doesn't interfere with other PHYs on the bus.
 
 maintainers:
   - J. Neuschäfer <j.ne@posteo.net>

-- 
2.48.0.rc1.219.gb6b6757d772

[PATCH v2 3/3] dt-bindings: net: Convert fsl,gianfar to YAML

[J. Neuschäfer via B4 Relay]

From: "J. Neuschäfer" <j.ne@posteo.net>

Add a binding for the "Gianfar" ethernet controller, also known as
TSEC/eTSEC.

Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
---

V2:
- change MAC address in example to 00:00:00:00:00:00 instead of a real
  Motorola MAC address (suggested by Andrew Lunn)
- add constraints to #address/size-cells, fsl,num_tr/rx_queues
- remove unnecessary type from dma-coherent
- add minItems to interrupts
- remove unnecessary #address/size-cells from queue-group@.*
- describe interrupts of queue-group@.*
- remove unnecessary bus in example
- consistently use "type: boolean" for fsl,magic-packet,
  instead of "$ref: /schemas/types.yaml#/definitions/flag"
- fix name of rx-stash-idx property
- fix type of rx-stash-len/idx properties
- actually reference fsl,gianfar-mdio schema for mdio@.* subnodes
- disambiguate compatible = "gianfar" schemas by using a "select:" schema
---
 .../devicetree/bindings/net/fsl,gianfar.yaml       | 248 +++++++++++++++++++++
 .../devicetree/bindings/net/fsl-tsec-phy.txt       |  39 +---
 2 files changed, 249 insertions(+), 38 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/fsl,gianfar.yaml b/Documentation/devicetree/bindings/net/fsl,gianfar.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..f92f284aa05b0ee34e331661308b7258cbda43c0
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/fsl,gianfar.yaml
@@ -0,0 +1,248 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/fsl,gianfar.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale Three-Speed Ethernet Controller (TSEC), "Gianfar"
+
+maintainers:
+  - J. Neuschäfer <j.ne@posteo.net>
+
+# This is needed to distinguish gianfar.yaml and gianfar-mdio.yaml, because
+# both use compatible = "gianfar" (with different device_type values)
+select:
+  oneOf:
+    - properties:
+        compatible:
+          contains:
+            const: gianfar
+        device_type:
+          const: network
+      required:
+        - device_type
+
+    - properties:
+        compatible:
+          const: fsl,etsec2
+
+  required:
+    - compatible
+
+properties:
+  compatible:
+    enum:
+      - gianfar
+      - fsl,etsec2
+
+  device_type:
+    const: network
+
+  model:
+    enum:
+      - FEC
+      - TSEC
+      - eTSEC
+
+  reg:
+    maxItems: 1
+
+  ranges: true
+
+  "#address-cells":
+    enum: [ 1, 2 ]
+
+  "#size-cells":
+    enum: [ 1, 2 ]
+
+  cell-index:
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  interrupts:
+    minItems: 1
+    items:
+      - description: Transmit interrupt or single combined interrupt
+      - description: Receive interrupt
+      - description: Error interrupt
+
+  dma-coherent: true
+
+  fsl,magic-packet:
+    type: boolean
+    description:
+      If present, indicates that the hardware supports waking up via magic packet.
+
+  fsl,wake-on-filer:
+    type: boolean
+    description:
+      If present, indicates that the hardware supports waking up by Filer
+      General Purpose Interrupt (FGPI) asserted on the Rx int line. This is
+      an advanced power management capability allowing certain packet types
+      (user) defined by filer rules to wake up the system.
+
+  bd-stash:
+    type: boolean
+    description:
+      If present, indicates that the hardware supports stashing buffer
+      descriptors in the L2.
+
+  rx-stash-len:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Denotes the number of bytes of a received buffer to stash in the L2.
+
+  rx-stash-idx:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Denotes the index of the first byte from the received buffer to stash in
+      the L2.
+
+  fsl,num_rx_queues:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Number of receive queues
+    const: 8
+
+  fsl,num_tx_queues:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Number of transmit queues
+    const: 8
+
+  tbi-handle:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: Reference (phandle) to the TBI node
+
+required:
+  - compatible
+  - model
+
+patternProperties:
+  "^mdio@[0-9a-f]+$":
+    $ref: /schemas/net/fsl,gianfar-mdio.yaml#
+
+allOf:
+  - $ref: ethernet-controller.yaml#
+
+  # eTSEC2 controller nodes have "queue group" subnodes and don't need a "reg"
+  # property.
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: fsl,etsec2
+    then:
+      patternProperties:
+        "^queue-group@[0-9a-f]+$":
+          type: object
+
+          properties:
+            reg:
+              maxItems: 1
+
+            interrupts:
+              items:
+                - description: Transmit interrupt
+                - description: Receive interrupt
+                - description: Error interrupt
+
+          required:
+            - reg
+            - interrupts
+
+          additionalProperties: false
+    else:
+      required:
+        - reg
+
+  # TSEC and eTSEC devices require three interrupts
+  - if:
+      properties:
+        model:
+          contains:
+            enum: [ TSEC, eTSEC ]
+    then:
+      properties:
+        interrupts:
+          items:
+            - description: Transmit interrupt
+            - description: Receive interrupt
+            - description: Error interrupt
+
+
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    ethernet@24000 {
+        device_type = "network";
+        model = "TSEC";
+        compatible = "gianfar";
+        reg = <0x24000 0x1000>;
+        local-mac-address = [ 00 00 00 00 00 00 ];
+        interrupts = <29 2>, <30 2>, <34 2>;
+        interrupt-parent = <&mpic>;
+        phy-handle = <&phy0>;
+    };
+
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    ethernet@24000 {
+        compatible = "gianfar";
+        reg = <0x24000 0x1000>;
+        ranges = <0x0 0x24000 0x1000>;
+        #address-cells = <1>;
+        #size-cells = <1>;
+        cell-index = <0>;
+        device_type = "network";
+        model = "eTSEC";
+        local-mac-address = [ 00 00 00 00 00 00 ];
+        interrupts = <32 IRQ_TYPE_LEVEL_LOW>,
+                     <33 IRQ_TYPE_LEVEL_LOW>,
+                     <34 IRQ_TYPE_LEVEL_LOW>;
+        interrupt-parent = <&ipic>;
+
+        mdio@520 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            compatible = "fsl,gianfar-mdio";
+            reg = <0x520 0x20>;
+        };
+    };
+
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    bus {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        ethernet {
+            compatible = "fsl,etsec2";
+            ranges;
+            device_type = "network";
+            #address-cells = <2>;
+            #size-cells = <2>;
+            interrupt-parent = <&gic>;
+            model = "eTSEC";
+            fsl,magic-packet;
+            dma-coherent;
+
+            queue-group@2d10000 {
+                reg = <0x0 0x2d10000 0x0 0x1000>;
+                interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+                             <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+                             <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+            };
+
+            queue-group@2d14000  {
+                reg = <0x0 0x2d14000 0x0 0x1000>;
+                interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+                             <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+                             <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
index 0e55e0af7d6f59cfb571dd3fcff704b7f4c140d2..b18bb4c997ea3a221e599f694d9a28692cbcaa7c 100644
--- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
+++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
@@ -8,44 +8,7 @@ Refer to Documentation/devicetree/bindings/net/fsl,gianfar-mdio.yaml
 
 * Gianfar-compatible ethernet nodes
 
-Properties:
-
-  - device_type : Should be "network"
-  - model : Model of the device.  Can be "TSEC", "eTSEC", or "FEC"
-  - compatible : Should be "gianfar"
-  - reg : Offset and length of the register set for the device
-  - interrupts : For FEC devices, the first interrupt is the device's
-    interrupt.  For TSEC and eTSEC devices, the first interrupt is
-    transmit, the second is receive, and the third is error.
-  - phy-handle : See ethernet.txt file in the same directory.
-  - fixed-link : See fixed-link.txt in the same directory.
-  - phy-connection-type : See ethernet.txt file in the same directory.
-    This property is only really needed if the connection is of type
-    "rgmii-id", as all other connection types are detected by hardware.
-  - fsl,magic-packet : If present, indicates that the hardware supports
-    waking up via magic packet.
-  - fsl,wake-on-filer : If present, indicates that the hardware supports
-    waking up by Filer General Purpose Interrupt (FGPI) asserted on the
-    Rx int line.  This is an advanced power management capability allowing
-    certain packet types (user) defined by filer rules to wake up the system.
-  - bd-stash : If present, indicates that the hardware supports stashing
-    buffer descriptors in the L2.
-  - rx-stash-len : Denotes the number of bytes of a received buffer to stash
-    in the L2.
-  - rx-stash-idx : Denotes the index of the first byte from the received
-    buffer to stash in the L2.
-
-Example:
-	ethernet@24000 {
-		device_type = "network";
-		model = "TSEC";
-		compatible = "gianfar";
-		reg = <0x24000 0x1000>;
-		local-mac-address = [ 00 E0 0C 00 73 00 ];
-		interrupts = <29 2 30 2 34 2>;
-		interrupt-parent = <&mpic>;
-		phy-handle = <&phy0>
-	};
+Refer to Documentation/devicetree/bindings/net/fsl,gianfar.yaml
 
 * Gianfar PTP clock nodes
 

-- 
2.48.0.rc1.219.gb6b6757d772

Re: [PATCH v2 1/3] dt-bindings: net: Convert fsl,gianfar-{mdio,tbi} to YAML

[Rob Herring (Arm)]

On Fri, 28 Feb 2025 18:32:50 +0100, J. Neuschäfer wrote:
> Move the information related to the Freescale Gianfar (TSEC) MDIO bus
> and the Ten-Bit Interface (TBI) from fsl-tsec-phy.txt to a new binding
> file in YAML format, fsl,gianfar-mdio.yaml.
> 
> Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
> ---
> 
> V2:
> - remove definitions of #address/size-cells (already in mdio.yaml)
> - disambiguate compatible = "gianfar" schemas by using a "select:" schema
> ---
>  .../devicetree/bindings/net/fsl,gianfar-mdio.yaml  | 113 +++++++++++++++++++++
>  .../devicetree/bindings/net/fsl-tsec-phy.txt       |  41 +-------
>  2 files changed, 115 insertions(+), 39 deletions(-)
> 

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

Re: [PATCH v2 3/3] dt-bindings: net: Convert fsl,gianfar to YAML

[Rob Herring (Arm)]

On Fri, 28 Feb 2025 18:32:52 +0100, J. Neuschäfer wrote:
> Add a binding for the "Gianfar" ethernet controller, also known as
> TSEC/eTSEC.
> 
> Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
> ---
> 
> V2:
> - change MAC address in example to 00:00:00:00:00:00 instead of a real
>   Motorola MAC address (suggested by Andrew Lunn)
> - add constraints to #address/size-cells, fsl,num_tr/rx_queues
> - remove unnecessary type from dma-coherent
> - add minItems to interrupts
> - remove unnecessary #address/size-cells from queue-group@.*
> - describe interrupts of queue-group@.*
> - remove unnecessary bus in example
> - consistently use "type: boolean" for fsl,magic-packet,
>   instead of "$ref: /schemas/types.yaml#/definitions/flag"
> - fix name of rx-stash-idx property
> - fix type of rx-stash-len/idx properties
> - actually reference fsl,gianfar-mdio schema for mdio@.* subnodes
> - disambiguate compatible = "gianfar" schemas by using a "select:" schema
> ---
>  .../devicetree/bindings/net/fsl,gianfar.yaml       | 248 +++++++++++++++++++++
>  .../devicetree/bindings/net/fsl-tsec-phy.txt       |  39 +---
>  2 files changed, 249 insertions(+), 38 deletions(-)
> 

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

Re: [PATCH v2 0/3] net: Convert Gianfar (Triple Speed Ethernet Controller) bindings to YAML

[patchwork-bot+netdevbpf]

Hello:

This series was applied to netdev/net-next.git (main)
by Jakub Kicinski <kuba@kernel.org>:

On Fri, 28 Feb 2025 18:32:49 +0100 you wrote:
> The aim of this series is to modernize the device tree bindings for the
> Freescale "Gianfar" ethernet controller (a.k.a. TSEC, Triple Speed
> Ethernet Controller) by converting them to YAML.
> 
> Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
> ---
> Changes in v2:
> - various cleanups suggested by reviewers
> - use a 'select:' schema to disambiguate compatible = "gianfar" between
>   network controller and MDIO nodes
> - Link to v1: https://lore.kernel.org/r/20250220-gianfar-yaml-v1-0-0ba97fd1ef92@posteo.net
> 
> [...]

Here is the summary with links:
  - [v2,1/3] dt-bindings: net: Convert fsl,gianfar-{mdio,tbi} to YAML
    https://git.kernel.org/netdev/net-next/c/e4c4522390c9
  - [v2,2/3] dt-bindings: net: fsl,gianfar-mdio: Update information about TBI
    https://git.kernel.org/netdev/net-next/c/0386e29e60bd
  - [v2,3/3] dt-bindings: net: Convert fsl,gianfar to YAML
    https://git.kernel.org/netdev/net-next/c/a70fdd936818

You are awesome, thank you!
-- 
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html