* [1/9][PATCH 2.6] Restructure reset code
2004-06-15 17:47 [0/9] via-rhine: Major surgery Roger Luethi
@ 2004-06-15 17:48 ` Roger Luethi
2004-06-15 17:48 ` [2/9][PATCH 2.6] fix mc_filter on big-endian arch Roger Luethi
` (8 subsequent siblings)
9 siblings, 0 replies; 16+ messages in thread
From: Roger Luethi @ 2004-06-15 17:48 UTC (permalink / raw)
To: Jeff Garzik, Andrew Morton; +Cc: netdev
Restructure code to make it easier to maintain.
rhine_hw_init: resets chip, reloads eeprom
rhine_chip_reset: chip reset + what used to be wait_for_reset
rhine_reload_eeprom: reload eeprom, re-enable MMIO, disable EEPROM-controlled
WOL
Note: Chip reset clears a bunch of registers that should be reloaded
from EEPROM (which turns off MMIO). Deal with that later.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
--- orig/drivers/net/via-rhine.c
+++ mod/drivers/net/via-rhine.c
@@ -579,56 +579,76 @@
}
}
-static void wait_for_reset(struct net_device *dev, u32 quirks, char *name)
+static void rhine_chip_reset(struct net_device *dev)
{
long ioaddr = dev->base_addr;
+ struct rhine_private *rp = netdev_priv(dev);
int boguscnt = 20;
+ writew(CmdReset, ioaddr + ChipCmd);
IOSYNC;
if (readw(ioaddr + ChipCmd) & CmdReset) {
printk(KERN_INFO "%s: Reset not complete yet. "
- "Trying harder.\n", name);
+ "Trying harder.\n", DRV_NAME);
- /* Rhine-II needs to be forced sometimes */
- if (quirks & rqForceReset)
+ /* Force reset */
+ if (rp->quirks & rqForceReset)
writeb(0x40, ioaddr + MiscCmd);
- /* VT86C100A may need long delay after reset (dlink) */
- /* Seen on Rhine-II as well (rl) */
+ /* Reset can take somewhat longer (rare) */
while ((readw(ioaddr + ChipCmd) & CmdReset) && --boguscnt)
udelay(5);
-
}
if (debug > 1)
- printk(KERN_INFO "%s: Reset %s.\n", name,
+ printk(KERN_INFO "%s: Reset %s.\n", pci_name(rp->pdev),
boguscnt ? "succeeded" : "failed");
}
#ifdef USE_MMIO
-static void __devinit enable_mmio(long ioaddr, u32 quirks)
+static void __devinit enable_mmio(long pioaddr, u32 quirks)
{
int n;
if (quirks & rqRhineI) {
/* More recent docs say that this bit is reserved ... */
- n = inb(ioaddr + ConfigA) | 0x20;
- outb(n, ioaddr + ConfigA);
+ n = inb(pioaddr + ConfigA) | 0x20;
+ outb(n, pioaddr + ConfigA);
} else {
- n = inb(ioaddr + ConfigD) | 0x80;
- outb(n, ioaddr + ConfigD);
+ n = inb(pioaddr + ConfigD) | 0x80;
+ outb(n, pioaddr + ConfigD);
}
}
#endif
-static void __devinit reload_eeprom(long ioaddr)
+/*
+ * Loads bytes 0x00-0x05, 0x6E-0x6F, 0x78-0x7B from EEPROM
+ */
+static void __devinit rhine_reload_eeprom(long pioaddr, struct net_device *dev)
{
+ long ioaddr = dev->base_addr;
+ struct rhine_private *rp = netdev_priv(dev);
int i;
- outb(0x20, ioaddr + MACRegEEcsr);
+
+ outb(0x20, pioaddr + MACRegEEcsr);
/* Typically 2 cycles to reload. */
for (i = 0; i < 150; i++)
- if (! (inb(ioaddr + MACRegEEcsr) & 0x20))
+ if (! (inb(pioaddr + MACRegEEcsr) & 0x20))
break;
+
+#ifdef USE_MMIO
+ /*
+ * Reloading from EEPROM overwrites ConfigA-D, so we must re-enable
+ * MMIO. If reloading EEPROM was done first this could be avoided, but
+ * it is not known if that still works with the "win98-reboot" problem.
+ */
+ enable_mmio(pioaddr, rp->quirks);
+#endif
+
+ /* Turn off EEPROM-controlled wake-up (magic packet) */
+ if (rp->quirks & rqWOL)
+ writeb(readb(ioaddr + ConfigA) & 0xFE, ioaddr + ConfigA);
+
}
#ifdef CONFIG_NET_POLL_CONTROLLER
@@ -640,6 +660,15 @@
}
#endif
+static void rhine_hw_init(struct net_device *dev, long pioaddr)
+{
+ /* Reset the chip to erase previous misconfiguration. */
+ rhine_chip_reset(dev);
+
+ /* Reload EEPROM controlled bytes cleared by soft reset */
+ rhine_reload_eeprom(pioaddr, dev);
+}
+
static int __devinit rhine_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
@@ -649,13 +678,11 @@
u8 pci_rev;
u32 quirks;
static int card_idx = -1;
- long ioaddr;
+ long pioaddr;
long memaddr;
+ long ioaddr;
int io_size;
int phy, phy_idx = 0;
-#ifdef USE_MMIO
- long ioaddr0;
-#endif
const char *name;
/* when built into the kernel, we only print version if device is found */
@@ -708,7 +735,7 @@
goto err_out;
}
- ioaddr = pci_resource_start(pdev, 0);
+ pioaddr = pci_resource_start(pdev, 0);
memaddr = pci_resource_start(pdev, 1);
pci_set_master(pdev);
@@ -728,8 +755,7 @@
goto err_out_free_netdev;
#ifdef USE_MMIO
- ioaddr0 = ioaddr;
- enable_mmio(ioaddr0, quirks);
+ enable_mmio(pioaddr, quirks);
ioaddr = (long) ioremap(memaddr, io_size);
if (!ioaddr) {
@@ -743,7 +769,7 @@
i = 0;
while (mmio_verify_registers[i]) {
int reg = mmio_verify_registers[i++];
- unsigned char a = inb(ioaddr0+reg);
+ unsigned char a = inb(pioaddr+reg);
unsigned char b = readb(ioaddr+reg);
if (a != b) {
rc = -EIO;
@@ -752,26 +778,18 @@
goto err_out_unmap;
}
}
+#else
+ ioaddr = pioaddr;
#endif /* USE_MMIO */
+
dev->base_addr = ioaddr;
+ rp = netdev_priv(dev);
+ rp->quirks = quirks;
rhine_power_init(dev);
/* Reset the chip to erase previous misconfiguration. */
- writew(CmdReset, ioaddr + ChipCmd);
-
- wait_for_reset(dev, quirks, shortname);
-
- /* Reload the station address from the EEPROM. */
-#ifdef USE_MMIO
- reload_eeprom(ioaddr0);
- /* Reloading from eeprom overwrites cfgA-D, so we must re-enable MMIO.
- If reload_eeprom() was done first this could be avoided, but it is
- not known if that still works with the "win98-reboot" problem. */
- enable_mmio(ioaddr0, quirks);
-#else
- reload_eeprom(ioaddr);
-#endif
+ rhine_hw_init(dev, pioaddr);
for (i = 0; i < 6; i++)
dev->dev_addr[i] = readb(ioaddr + StationAddr + i);
@@ -782,15 +800,6 @@
goto err_out_unmap;
}
- if (quirks & rqWOL) {
- /*
- * for 3065D, EEPROM reloaded will cause bit 0 in MAC_REG_CFGA
- * turned on. it makes MAC receive magic packet
- * automatically. So, we turn it off. (D-Link)
- */
- writeb(readb(ioaddr + ConfigA) & 0xFE, ioaddr + ConfigA);
- }
-
/* Select backoff algorithm */
if (backoff)
writeb(readb(ioaddr + ConfigD) & (0xF0 | backoff),
@@ -798,10 +807,8 @@
dev->irq = pdev->irq;
- rp = netdev_priv(dev);
spin_lock_init(&rp->lock);
rp->pdev = pdev;
- rp->quirks = quirks;
rp->mii_if.dev = dev;
rp->mii_if.mdio_read = mdio_read;
rp->mii_if.mdio_write = mdio_write;
@@ -1170,9 +1177,6 @@
long ioaddr = dev->base_addr;
int i;
- /* Reset the chip. */
- writew(CmdReset, ioaddr + ChipCmd);
-
i = request_irq(rp->pdev->irq, &rhine_interrupt, SA_SHIRQ, dev->name,
dev);
if (i)
@@ -1187,7 +1191,7 @@
return i;
alloc_rbufs(dev);
alloc_tbufs(dev);
- wait_for_reset(dev, rp->quirks, dev->name);
+ rhine_chip_reset(dev);
init_registers(dev);
if (debug > 2)
printk(KERN_DEBUG "%s: Done rhine_open(), status %4.4x "
@@ -1283,9 +1287,6 @@
spin_lock(&rp->lock);
- /* Reset the chip. */
- writew(CmdReset, ioaddr + ChipCmd);
-
/* clear all descriptors */
free_tbufs(dev);
free_rbufs(dev);
@@ -1293,7 +1294,7 @@
alloc_rbufs(dev);
/* Reinitialize the hardware. */
- wait_for_reset(dev, rp->quirks, dev->name);
+ rhine_chip_reset(dev);
init_registers(dev);
spin_unlock(&rp->lock);
^ permalink raw reply [flat|nested] 16+ messages in thread* [2/9][PATCH 2.6] fix mc_filter on big-endian arch
2004-06-15 17:47 [0/9] via-rhine: Major surgery Roger Luethi
2004-06-15 17:48 ` [1/9][PATCH 2.6] Restructure reset code Roger Luethi
@ 2004-06-15 17:48 ` Roger Luethi
2004-06-15 17:48 ` [3/9][PATCH 2.6] Remove lingering PHY special casing Roger Luethi
` (7 subsequent siblings)
9 siblings, 0 replies; 16+ messages in thread
From: Roger Luethi @ 2004-06-15 17:48 UTC (permalink / raw)
To: Jeff Garzik, Andrew Morton; +Cc: netdev
A.J. from VIA Networking Technologies noticed that via-rhine is using
cpu_to_le32() when preparing mc_filter hashes. This breaks Rhine hardware
multicast filters on big-endian architectures.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
--- 2.6-bk/drivers/net/via-rhine.c.orig 2004-06-06 18:03:21.323194221 +0200
+++ 2.6-bk/drivers/net/via-rhine.c 2004-06-06 18:05:22.137319854 +0200
@@ -1782,7 +1782,7 @@
i++, mclist = mclist->next) {
int bit_nr = ether_crc(ETH_ALEN, mclist->dmi_addr) >> 26;
- mc_filter[bit_nr >> 5] |= cpu_to_le32(1 << (bit_nr & 31));
+ mc_filter[bit_nr >> 5] |= 1 << (bit_nr & 31);
}
writel(mc_filter[0], ioaddr + MulticastFilter0);
writel(mc_filter[1], ioaddr + MulticastFilter1);
^ permalink raw reply [flat|nested] 16+ messages in thread* [3/9][PATCH 2.6] Remove lingering PHY special casing
2004-06-15 17:47 [0/9] via-rhine: Major surgery Roger Luethi
2004-06-15 17:48 ` [1/9][PATCH 2.6] Restructure reset code Roger Luethi
2004-06-15 17:48 ` [2/9][PATCH 2.6] fix mc_filter on big-endian arch Roger Luethi
@ 2004-06-15 17:48 ` Roger Luethi
2004-06-15 17:49 ` [4/9][PATCH 2.6] Rewrite PHY detection Roger Luethi
` (6 subsequent siblings)
9 siblings, 0 replies; 16+ messages in thread
From: Roger Luethi @ 2004-06-15 17:48 UTC (permalink / raw)
To: Jeff Garzik, Andrew Morton; +Cc: netdev
All this code is broken (e.g. unconditionally programs all PHYs as if
they were the same model) and/or unused (IntrLinkChange never occurs
with driver as is).
Signed-off-by: Roger Luethi <rl@hellgate.ch>
--- orig/drivers/net/via-rhine.c
+++ mod/drivers/net/via-rhine.c
@@ -373,7 +373,6 @@
enum rhine_quirks {
rqWOL = 0x0001, /* Wake-On-LAN support */
rqForceReset = 0x0002,
- rqDavicomPhy = 0x0020,
rq6patterns = 0x0040, /* 6 instead of 4 patterns for WOL */
rqStatusWBRace = 0x0080, /* Tx Status Writeback Error possible */
rqRhineI = 0x0100, /* See comment below */
@@ -698,7 +697,7 @@
io_size = 256;
if (pci_rev < VT6102) {
- quirks = rqRhineI | rqDavicomPhy;
+ quirks = rqRhineI;
io_size = 128;
name = "VT86C100A Rhine";
}
@@ -1113,11 +1112,6 @@
writew(rp->chip_cmd, ioaddr + ChipCmd);
rhine_check_duplex(dev);
-
- /* The LED outputs of various MII xcvrs should be configured. */
- /* For NS or Mison phys, turn on bit 1 in register 0x17 */
- mdio_write(dev, rp->phys[0], 0x17, mdio_read(dev, rp->phys[0], 0x17) |
- 0x0001);
}
/* Read and write over the MII Management Data I/O (MDIO) interface. */
@@ -1692,12 +1686,7 @@
spin_lock(&rp->lock);
if (intr_status & (IntrLinkChange)) {
- if (readb(ioaddr + MIIStatus) & 0x02) {
- /* Link failed, restart autonegotiation. */
- if (rp->quirks & rqRhineI)
- mdio_write(dev, rp->phys[0], MII_BMCR, 0x3300);
- } else
- rhine_check_duplex(dev);
+ rhine_check_duplex(dev);
if (debug)
printk(KERN_ERR "%s: MII status changed: "
"Autonegotiation advertising %4.4x partner "
^ permalink raw reply [flat|nested] 16+ messages in thread* [4/9][PATCH 2.6] Rewrite PHY detection
2004-06-15 17:47 [0/9] via-rhine: Major surgery Roger Luethi
` (2 preceding siblings ...)
2004-06-15 17:48 ` [3/9][PATCH 2.6] Remove lingering PHY special casing Roger Luethi
@ 2004-06-15 17:49 ` Roger Luethi
2004-06-15 17:49 ` [5/9][PATCH 2.6] Remove options, full_duplex parameters Roger Luethi
` (5 subsequent siblings)
9 siblings, 0 replies; 16+ messages in thread
From: Roger Luethi @ 2004-06-15 17:49 UTC (permalink / raw)
To: Jeff Garzik, Andrew Morton; +Cc: netdev
Instead of probing, set phy_id to 1 for Rhine III and read phy_id from
EEPROM-controlled register for Rhine I/II.
Remove code for handling anything other than 1 MII PHY. If it wasn't
unnecessary code to begin with, it would need to be fixed because it
wouldn't work.
Use mii_if_info.phy_id as the only container of phy_id. Not particulary
happy about those names (phy_id vs. MII_PHYSIDx), but being consequent
about it mitigates confusion.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
--- orig/drivers/net/via-rhine.c
+++ mod/drivers/net/via-rhine.c
@@ -475,7 +475,6 @@
CmdNoTxPoll=0x0800, CmdReset=0x8000,
};
-#define MAX_MII_CNT 4
struct rhine_private {
/* Descriptor rings */
struct rx_desc *rx_ring;
@@ -513,8 +512,6 @@
u8 tx_thresh, rx_thresh;
/* MII transceiver section. */
- unsigned char phys[MAX_MII_CNT]; /* MII device addresses. */
- unsigned int mii_cnt; /* number of MIIs found, but only the first one is used */
u16 mii_status; /* last read MII status */
struct mii_if_info mii_if;
};
@@ -622,6 +619,7 @@
/*
* Loads bytes 0x00-0x05, 0x6E-0x6F, 0x78-0x7B from EEPROM
+ * (plus 0x6C for Rhine I/II)
*/
static void __devinit rhine_reload_eeprom(long pioaddr, struct net_device *dev)
{
@@ -680,8 +678,7 @@
long pioaddr;
long memaddr;
long ioaddr;
- int io_size;
- int phy, phy_idx = 0;
+ int io_size, phy_id;
const char *name;
/* when built into the kernel, we only print version if device is found */
@@ -696,6 +693,7 @@
pci_read_config_byte(pdev, PCI_REVISION_ID, &pci_rev);
io_size = 256;
+ phy_id = 0;
if (pci_rev < VT6102) {
quirks = rqRhineI;
io_size = 128;
@@ -709,6 +707,7 @@
}
else {
name = "Rhine III";
+ phy_id = 1; /* Integrated PHY, phy_id fixed to 1 */
if (pci_rev >= VT6105_B0)
quirks |= rq6patterns;
}
@@ -804,6 +803,10 @@
writeb(readb(ioaddr + ConfigD) & (0xF0 | backoff),
ioaddr + ConfigD);
+ /* For Rhine I/II, phy_id is loaded from EEPROM */
+ if (!phy_id)
+ phy_id = readb(ioaddr + 0x6C);
+
dev->irq = pdev->irq;
spin_lock_init(&rp->lock);
@@ -867,17 +870,15 @@
pci_set_drvdata(pdev, dev);
- rp->phys[0] = 1; /* Standard for this chip. */
- for (phy = 1; phy < 32 && phy_idx < MAX_MII_CNT; phy++) {
- int mii_status = mdio_read(dev, phy, 1);
+ {
+ int mii_status = mdio_read(dev, phy_id, 1);
if (mii_status != 0xffff && mii_status != 0x0000) {
- rp->phys[phy_idx++] = phy;
- rp->mii_if.advertising = mdio_read(dev, phy, 4);
+ rp->mii_if.advertising = mdio_read(dev, phy_id, 4);
printk(KERN_INFO "%s: MII PHY found at address "
"%d, status 0x%4.4x advertising %4.4x "
- "Link %4.4x.\n", dev->name, phy,
+ "Link %4.4x.\n", dev->name, phy_id,
mii_status, rp->mii_if.advertising,
- mdio_read(dev, phy, 5));
+ mdio_read(dev, phy_id, 5));
/* set IFF_RUNNING */
if (mii_status & BMSR_LSTATUS)
@@ -885,11 +886,9 @@
else
netif_carrier_off(dev);
- break;
}
}
- rp->mii_cnt = phy_idx;
- rp->mii_if.phy_id = rp->phys[0];
+ rp->mii_if.phy_id = phy_id;
/* Allow forcing the media type. */
if (option > 0) {
@@ -900,10 +899,9 @@
"operation.\n",
(option & 0x300 ? 100 : 10),
(option & 0x220 ? "full" : "half"));
- if (rp->mii_cnt)
- mdio_write(dev, rp->phys[0], MII_BMCR,
- ((option & 0x300) ? 0x2000 : 0) | /* 100mbps? */
- ((option & 0x220) ? 0x0100 : 0)); /* Full duplex? */
+ mdio_write(dev, phy_id, MII_BMCR,
+ ((option & 0x300) ? 0x2000 : 0) | /* 100mbps? */
+ ((option & 0x220) ? 0x0100 : 0)); /* Full duplex? */
}
}
@@ -1140,7 +1138,7 @@
long ioaddr = dev->base_addr;
int boguscnt = 1024;
- if (phy_id == rp->phys[0]) {
+ if (phy_id == rp->mii_if.phy_id) {
switch (regnum) {
case MII_BMCR: /* Is user forcing speed/duplex? */
if (value & 0x9000) /* Autonegotiation. */
@@ -1191,7 +1189,7 @@
printk(KERN_DEBUG "%s: Done rhine_open(), status %4.4x "
"MII status: %4.4x.\n",
dev->name, readw(ioaddr + ChipCmd),
- mdio_read(dev, rp->phys[0], MII_BMSR));
+ mdio_read(dev, rp->mii_if.phy_id, MII_BMSR));
netif_start_queue(dev);
@@ -1209,7 +1207,7 @@
{
struct rhine_private *rp = netdev_priv(dev);
long ioaddr = dev->base_addr;
- int mii_lpa = mdio_read(dev, rp->phys[0], MII_LPA);
+ int mii_lpa = mdio_read(dev, rp->mii_if.phy_id, MII_LPA);
int negotiated = mii_lpa & rp->mii_if.advertising;
int duplex;
@@ -1222,7 +1220,7 @@
printk(KERN_INFO "%s: Setting %s-duplex based on "
"MII #%d link partner capability of %4.4x.\n",
dev->name, duplex ? "full" : "half",
- rp->phys[0], mii_lpa);
+ rp->mii_if.phy_id, mii_lpa);
if (duplex)
rp->chip_cmd |= CmdFDuplex;
else
@@ -1250,7 +1248,7 @@
rhine_check_duplex(dev);
/* make IFF_RUNNING follow the MII status bit "Link established" */
- mii_status = mdio_read(dev, rp->phys[0], MII_BMSR);
+ mii_status = mdio_read(dev, rp->mii_if.phy_id, MII_BMSR);
if ((mii_status & BMSR_LSTATUS) != (rp->mii_status & BMSR_LSTATUS)) {
if (mii_status & BMSR_LSTATUS)
netif_carrier_on(dev);
@@ -1274,7 +1272,7 @@
printk(KERN_WARNING "%s: Transmit timed out, status %4.4x, PHY status "
"%4.4x, resetting...\n",
dev->name, readw(ioaddr + IntrStatus),
- mdio_read(dev, rp->phys[0], MII_BMSR));
+ mdio_read(dev, rp->mii_if.phy_id, MII_BMSR));
/* protect against concurrent rx interrupts */
disable_irq(rp->pdev->irq);
@@ -1691,8 +1689,8 @@
printk(KERN_ERR "%s: MII status changed: "
"Autonegotiation advertising %4.4x partner "
"%4.4x.\n", dev->name,
- mdio_read(dev, rp->phys[0], MII_ADVERTISE),
- mdio_read(dev, rp->phys[0], MII_LPA));
+ mdio_read(dev, rp->mii_if.phy_id, MII_ADVERTISE),
+ mdio_read(dev, rp->mii_if.phy_id, MII_LPA));
}
if (intr_status & IntrStatsMax) {
rp->stats.rx_crc_errors += readw(ioaddr + RxCRCErrs);
^ permalink raw reply [flat|nested] 16+ messages in thread* [5/9][PATCH 2.6] Remove options, full_duplex parameters
2004-06-15 17:47 [0/9] via-rhine: Major surgery Roger Luethi
` (3 preceding siblings ...)
2004-06-15 17:49 ` [4/9][PATCH 2.6] Rewrite PHY detection Roger Luethi
@ 2004-06-15 17:49 ` Roger Luethi
2004-06-15 17:49 ` [7/9][PATCH 2.6] Media mode rewrite Roger Luethi
` (4 subsequent siblings)
9 siblings, 0 replies; 16+ messages in thread
From: Roger Luethi @ 2004-06-15 17:49 UTC (permalink / raw)
To: Jeff Garzik, Andrew Morton; +Cc: netdev
Nobody complained although media locking parameters were broken
forever. They were sort of fixed recently, but the code is still in a
bad shape.
More seriously, the options/full_duplex stuff has fundamental design
problems that have been discussed in-depth on the list (e.g. effect of
hotplugging, nameif, suspend/resume).
For those needing media locking with Linux 2.6+ via-rhine, ethtool(8)
is the replacement.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
--- orig/drivers/net/via-rhine.c
+++ mod/drivers/net/via-rhine.c
@@ -145,19 +145,10 @@
/* Select a backoff algorithm (Ethernet capture effect) */
static int backoff;
-/* Used to pass the media type, etc.
- Both 'options[]' and 'full_duplex[]' should exist for driver
- interoperability.
- The media type is usually passed in 'options[]'.
- The default is autonegotiation for speed and duplex.
- This should rarely be overridden.
- Use option values 0x10/0x20 for 10Mbps, 0x100,0x200 for 100Mbps.
- Use option values 0x10 and 0x100 for forcing half duplex fixed speed.
- Use option values 0x20 and 0x200 for forcing full duplex operation.
-*/
-#define MAX_UNITS 8 /* More are supported, limit only on options */
-static int options[MAX_UNITS] = {-1, -1, -1, -1, -1, -1, -1, -1};
-static int full_duplex[MAX_UNITS] = {-1, -1, -1, -1, -1, -1, -1, -1};
+/*
+ * In case you are looking for 'options[]' or 'full_duplex[]', they
+ * are gone. Use ethtool(8) instead.
+ */
/* Maximum number of multicast addresses to filter (vs. rx-all-multicast).
The Rhine has a 64 element 8390-like hash table. */
@@ -246,14 +237,10 @@
MODULE_PARM(debug, "i");
MODULE_PARM(rx_copybreak, "i");
MODULE_PARM(backoff, "i");
-MODULE_PARM(options, "1-" __MODULE_STRING(MAX_UNITS) "i");
-MODULE_PARM(full_duplex, "1-" __MODULE_STRING(MAX_UNITS) "i");
MODULE_PARM_DESC(max_interrupt_work, "VIA Rhine maximum events handled per interrupt");
MODULE_PARM_DESC(debug, "VIA Rhine debug level (0-7)");
MODULE_PARM_DESC(rx_copybreak, "VIA Rhine copy breakpoint for copy-only-tiny-frames");
MODULE_PARM_DESC(backoff, "VIA Rhine: Bits 0-3: backoff algorithm");
-MODULE_PARM_DESC(options, "VIA Rhine: Bits 0-3: media type, bit 17: full duplex");
-MODULE_PARM_DESC(full_duplex, "VIA Rhine full duplex setting(s) (1)");
/*
Theory of Operation
@@ -671,7 +658,7 @@
{
struct net_device *dev;
struct rhine_private *rp;
- int i, option, rc;
+ int i, rc;
u8 pci_rev;
u32 quirks;
static int card_idx = -1;
@@ -688,8 +675,6 @@
printk(version);
#endif
- card_idx++;
- option = card_idx < MAX_UNITS ? options[card_idx] : 0;
pci_read_config_byte(pdev, PCI_REVISION_ID, &pci_rev);
io_size = 256;
@@ -817,9 +802,6 @@
rp->mii_if.phy_id_mask = 0x1f;
rp->mii_if.reg_num_mask = 0x1f;
- if (dev->mem_start)
- option = dev->mem_start;
-
/* The chip-specific entries in the device structure. */
dev->open = rhine_open;
dev->hard_start_xmit = rhine_start_tx;
@@ -841,20 +823,6 @@
if (rc)
goto err_out_unmap;
- /* The lower four bits are the media type. */
- if (option > 0) {
- if (option & 0x220)
- rp->mii_if.full_duplex = 1;
- }
- if (card_idx < MAX_UNITS && full_duplex[card_idx] > 0)
- rp->mii_if.full_duplex = 1;
-
- if (rp->mii_if.full_duplex) {
- printk(KERN_INFO "%s: Set to forced full duplex, "
- "autonegotiation disabled.\n", dev->name);
- rp->mii_if.force_media = 1;
- }
-
printk(KERN_INFO "%s: VIA %s at 0x%lx, ",
dev->name, name,
#ifdef USE_MMIO
@@ -890,21 +858,6 @@
}
rp->mii_if.phy_id = phy_id;
- /* Allow forcing the media type. */
- if (option > 0) {
- if (option & 0x220)
- rp->mii_if.full_duplex = 1;
- if (option & 0x330) {
- printk(KERN_INFO " Forcing %dMbs %s-duplex "
- "operation.\n",
- (option & 0x300 ? 100 : 10),
- (option & 0x220 ? "full" : "half"));
- mdio_write(dev, phy_id, MII_BMCR,
- ((option & 0x300) ? 0x2000 : 0) | /* 100mbps? */
- ((option & 0x220) ? 0x0100 : 0)); /* Full duplex? */
- }
- }
-
return 0;
err_out_unmap:
^ permalink raw reply [flat|nested] 16+ messages in thread* [7/9][PATCH 2.6] Media mode rewrite
2004-06-15 17:47 [0/9] via-rhine: Major surgery Roger Luethi
` (4 preceding siblings ...)
2004-06-15 17:49 ` [5/9][PATCH 2.6] Remove options, full_duplex parameters Roger Luethi
@ 2004-06-15 17:49 ` Roger Luethi
2004-06-19 21:24 ` Jeff Garzik
2004-06-15 17:49 ` [8/9][PATCH 2.6] Small fixes and clean-up Roger Luethi
` (3 subsequent siblings)
9 siblings, 1 reply; 16+ messages in thread
From: Roger Luethi @ 2004-06-15 17:49 UTC (permalink / raw)
To: Jeff Garzik, Andrew Morton; +Cc: netdev
Remove rhine_check_duplex, rhine_timer and related data structures
Add rhine_check_media: wrapper for generic mii_check_media, sets duplex
bit in MAC
Add rhine_enable_linkmon, rhine_disable_linkmon to enable hardware link
status monitoring
Update mdio_read, mdio_write accordingly
Remove get_intr_status check in rhine_start_tx because we are not racing
anymore
Signed-off-by: Roger Luethi <rl@hellgate.ch>
--- orig/drivers/net/via-rhine.c
+++ mod/drivers/net/via-rhine.c
@@ -485,7 +485,6 @@
struct pci_dev *pdev;
struct net_device_stats stats;
- struct timer_list timer; /* Media monitoring timer. */
spinlock_t lock;
/* Frequently used values: keep some adjacent for cache effect. */
@@ -498,16 +497,12 @@
/* These values are keep track of the transceiver/media in use. */
u8 tx_thresh, rx_thresh;
- /* MII transceiver section. */
- u16 mii_status; /* last read MII status */
struct mii_if_info mii_if;
};
static int mdio_read(struct net_device *dev, int phy_id, int location);
static void mdio_write(struct net_device *dev, int phy_id, int location, int value);
static int rhine_open(struct net_device *dev);
-static void rhine_check_duplex(struct net_device *dev);
-static void rhine_timer(unsigned long data);
static void rhine_tx_timeout(struct net_device *dev);
static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev);
static irqreturn_t rhine_interrupt(int irq, void *dev_instance, struct pt_regs *regs);
@@ -1032,6 +1027,21 @@
}
}
+static void rhine_check_media(struct net_device *dev, unsigned int init_media)
+{
+ struct rhine_private *rp = netdev_priv(dev);
+ long ioaddr = dev->base_addr;
+
+ mii_check_media(&rp->mii_if, debug, init_media);
+
+ if (rp->mii_if.full_duplex)
+ writeb(readb(ioaddr + ChipCmd1) | Cmd1FDuplex,
+ ioaddr + ChipCmd1);
+ else
+ writeb(readb(ioaddr + ChipCmd1) & ~Cmd1FDuplex,
+ ioaddr + ChipCmd1);
+}
+
static void init_registers(struct net_device *dev)
{
struct rhine_private *rp = netdev_priv(dev);
@@ -1047,7 +1057,6 @@
writeb(0x20, ioaddr + TxConfig);
rp->tx_thresh = 0x20;
rp->rx_thresh = 0x60; /* Written in rhine_set_rx_mode(). */
- rp->mii_if.full_duplex = 0;
writel(rp->rx_ring_dma, ioaddr + RxRingPtr);
writel(rp->tx_ring_dma, ioaddr + TxRingPtr);
@@ -1063,14 +1072,42 @@
writew(CmdStart|CmdTxOn|CmdRxOn|(Cmd1NoTxPoll << 8),
ioaddr + ChipCmd);
- if (rp->mii_if.force_media)
- writeb(readb(ioaddr + ChipCmd1) | Cmd1FDuplex,
- ioaddr + ChipCmd1);
- else
- writeb(readb(ioaddr + ChipCmd1) & ~Cmd1FDuplex,
- ioaddr + ChipCmd1);
+ rhine_check_media(dev, 1);
+}
+
+/* Enable MII link status auto-polling (required for IntrLinkChange) */
+static void rhine_enable_linkmon(long ioaddr)
+{
+ writeb(0, ioaddr + MIICmd);
+ writeb(MII_BMSR, ioaddr + MIIRegAddr);
+ writeb(0x80, ioaddr + MIICmd);
- rhine_check_duplex(dev);
+ RHINE_WAIT_FOR((readb(ioaddr + MIIRegAddr) & 0x20));
+
+ writeb(MII_BMSR | 0x40, ioaddr + MIIRegAddr);
+}
+
+/* Disable MII link status auto-polling (required for MDIO access) */
+static void rhine_disable_linkmon(long ioaddr, u32 quirks)
+{
+ writeb(0, ioaddr + MIICmd);
+
+ if (quirks & rqRhineI) {
+ writeb(0x01, ioaddr + MIIRegAddr); // MII_BMSR
+
+ /* Can be called from ISR. Evil. */
+ mdelay(1);
+
+ /* 0x80 must be set immediately before turning it off */
+ writeb(0x80, ioaddr + MIICmd);
+
+ RHINE_WAIT_FOR(readb(ioaddr + MIIRegAddr) & 0x20);
+
+ /* Heh. Now clear 0x80 again. */
+ writeb(0, ioaddr + MIICmd);
+ }
+ else
+ RHINE_WAIT_FOR(readb(ioaddr + MIIRegAddr) & 0x80);
}
/* Read and write over the MII Management Data I/O (MDIO) interface. */
@@ -1078,15 +1115,20 @@
static int mdio_read(struct net_device *dev, int phy_id, int regnum)
{
long ioaddr = dev->base_addr;
+ struct rhine_private *rp = netdev_priv(dev);
+ int result;
- /* Wait for a previous command to complete. */
- RHINE_WAIT_FOR(!(readb(ioaddr + MIICmd) & 0x60));
- writeb(0x00, ioaddr + MIICmd);
+ rhine_disable_linkmon(ioaddr, rp->quirks);
+
+ writeb(0, ioaddr + MIICmd);
writeb(phy_id, ioaddr + MIIPhyAddr);
writeb(regnum, ioaddr + MIIRegAddr);
writeb(0x40, ioaddr + MIICmd); /* Trigger read */
RHINE_WAIT_FOR(!(readb(ioaddr + MIICmd) & 0x40));
- return readw(ioaddr + MIIData);
+ result = readw(ioaddr + MIIData);
+
+ rhine_enable_linkmon(ioaddr);
+ return result;
}
static void mdio_write(struct net_device *dev, int phy_id, int regnum, int value)
@@ -1094,29 +1136,17 @@
struct rhine_private *rp = netdev_priv(dev);
long ioaddr = dev->base_addr;
- if (phy_id == rp->mii_if.phy_id) {
- switch (regnum) {
- case MII_BMCR: /* Is user forcing speed/duplex? */
- if (value & 0x9000) /* Autonegotiation. */
- rp->mii_if.force_media = 0;
- else
- rp->mii_if.full_duplex = (value & 0x0100) ? 1 : 0;
- break;
- case MII_ADVERTISE:
- rp->mii_if.advertising = value;
- break;
- }
- }
+ rhine_disable_linkmon(ioaddr, rp->quirks);
- /* Wait for a previous command to complete. */
- RHINE_WAIT_FOR(!(readb(ioaddr + MIICmd) & 0x60));
- writeb(0x00, ioaddr + MIICmd);
+ writeb(0, ioaddr + MIICmd);
writeb(phy_id, ioaddr + MIIPhyAddr);
writeb(regnum, ioaddr + MIIRegAddr);
writew(value, ioaddr + MIIData);
writeb(0x20, ioaddr + MIICmd); /* Trigger write. */
-}
+ RHINE_WAIT_FOR(!(readb(ioaddr + MIICmd) & 0x20));
+ rhine_enable_linkmon(ioaddr);
+}
static int rhine_open(struct net_device *dev)
{
@@ -1148,78 +1178,9 @@
netif_start_queue(dev);
- /* Set the timer to check for link beat. */
- init_timer(&rp->timer);
- rp->timer.expires = jiffies + 2 * HZ/100;
- rp->timer.data = (unsigned long)dev;
- rp->timer.function = &rhine_timer; /* timer handler */
- add_timer(&rp->timer);
-
return 0;
}
-static void rhine_check_duplex(struct net_device *dev)
-{
- struct rhine_private *rp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
- int mii_lpa = mdio_read(dev, rp->mii_if.phy_id, MII_LPA);
- int negotiated = mii_lpa & rp->mii_if.advertising;
- int duplex;
-
- if (rp->mii_if.force_media || mii_lpa == 0xffff)
- return;
- duplex = (negotiated & 0x0100) || (negotiated & 0x01C0) == 0x0040;
- if (rp->mii_if.full_duplex != duplex) {
- rp->mii_if.full_duplex = duplex;
- if (debug)
- printk(KERN_INFO "%s: Setting %s-duplex based on "
- "MII #%d link partner capability of %4.4x.\n",
- dev->name, duplex ? "full" : "half",
- rp->mii_if.phy_id, mii_lpa);
- if (duplex)
- writeb(readb(ioaddr + ChipCmd1) | Cmd1FDuplex,
- ioaddr + ChipCmd1);
- else
- writeb(readb(ioaddr + ChipCmd1) & ~Cmd1FDuplex,
- ioaddr + ChipCmd1);
- }
-}
-
-
-static void rhine_timer(unsigned long data)
-{
- struct net_device *dev = (struct net_device *)data;
- struct rhine_private *rp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
- int next_tick = 10*HZ;
- int mii_status;
-
- if (debug > 3) {
- printk(KERN_DEBUG "%s: VIA Rhine monitor tick, status %4.4x.\n",
- dev->name, readw(ioaddr + IntrStatus));
- }
-
- spin_lock_irq (&rp->lock);
-
- rhine_check_duplex(dev);
-
- /* make IFF_RUNNING follow the MII status bit "Link established" */
- mii_status = mdio_read(dev, rp->mii_if.phy_id, MII_BMSR);
- if ((mii_status & BMSR_LSTATUS) != (rp->mii_status & BMSR_LSTATUS)) {
- if (mii_status & BMSR_LSTATUS)
- netif_carrier_on(dev);
- else
- netif_carrier_off(dev);
- }
- rp->mii_status = mii_status;
-
- spin_unlock_irq(&rp->lock);
-
- rp->timer.expires = jiffies + next_tick;
- add_timer(&rp->timer);
-}
-
-
static void rhine_tx_timeout(struct net_device *dev)
{
struct rhine_private *rp = netdev_priv(dev);
@@ -1256,8 +1217,8 @@
static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev)
{
struct rhine_private *rp = netdev_priv(dev);
+ long ioaddr = dev->base_addr;
unsigned entry;
- u32 intr_status;
/* Caution: the write order is important here, set the field
with the "ownership" bits last. */
@@ -1308,15 +1269,9 @@
/* Non-x86 Todo: explicitly flush cache lines here. */
- /*
- * Wake the potentially-idle transmit channel unless errors are
- * pending (the ISR must sort them out first).
- */
- intr_status = get_intr_status(dev);
- if ((intr_status & IntrTxErrSummary) == 0) {
- writeb(readb(dev->base_addr + ChipCmd1) | Cmd1TxDemand,
- dev->base_addr + ChipCmd1);
- }
+ /* Wake the potentially-idle transmit channel */
+ writeb(readb(ioaddr + ChipCmd1) | Cmd1TxDemand,
+ ioaddr + ChipCmd1);
IOSYNC;
if (rp->cur_tx == rp->dirty_tx + TX_QUEUE_LEN)
@@ -1639,15 +1594,8 @@
spin_lock(&rp->lock);
- if (intr_status & (IntrLinkChange)) {
- rhine_check_duplex(dev);
- if (debug)
- printk(KERN_ERR "%s: MII status changed: "
- "Autonegotiation advertising %4.4x partner "
- "%4.4x.\n", dev->name,
- mdio_read(dev, rp->mii_if.phy_id, MII_ADVERTISE),
- mdio_read(dev, rp->mii_if.phy_id, MII_LPA));
- }
+ if (intr_status & IntrLinkChange)
+ rhine_check_media(dev, 0);
if (intr_status & IntrStatsMax) {
rp->stats.rx_crc_errors += readw(ioaddr + RxCRCErrs);
rp->stats.rx_missed_errors += readw(ioaddr + RxMissed);
@@ -1839,8 +1786,6 @@
long ioaddr = dev->base_addr;
struct rhine_private *rp = netdev_priv(dev);
- del_timer_sync(&rp->timer);
-
spin_lock_irq(&rp->lock);
netif_stop_queue(dev);
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [7/9][PATCH 2.6] Media mode rewrite
2004-06-15 17:49 ` [7/9][PATCH 2.6] Media mode rewrite Roger Luethi
@ 2004-06-19 21:24 ` Jeff Garzik
2004-06-19 22:20 ` Roger Luethi
0 siblings, 1 reply; 16+ messages in thread
From: Jeff Garzik @ 2004-06-19 21:24 UTC (permalink / raw)
To: Roger Luethi; +Cc: Andrew Morton, netdev
Roger Luethi wrote:
> Remove rhine_check_duplex, rhine_timer and related data structures
>
> Add rhine_check_media: wrapper for generic mii_check_media, sets duplex
> bit in MAC
>
> Add rhine_enable_linkmon, rhine_disable_linkmon to enable hardware link
> status monitoring
>
> Update mdio_read, mdio_write accordingly
>
> Remove get_intr_status check in rhine_start_tx because we are not racing
> anymore
>
> Signed-off-by: Roger Luethi <rl@hellgate.ch>
>
> --- orig/drivers/net/via-rhine.c
> +++ mod/drivers/net/via-rhine.c
> @@ -485,7 +485,6 @@
>
> struct pci_dev *pdev;
> struct net_device_stats stats;
> - struct timer_list timer; /* Media monitoring timer. */
> spinlock_t lock;
>
> /* Frequently used values: keep some adjacent for cache effect. */
> @@ -498,16 +497,12 @@
> /* These values are keep track of the transceiver/media in use. */
> u8 tx_thresh, rx_thresh;
>
> - /* MII transceiver section. */
> - u16 mii_status; /* last read MII status */
> struct mii_if_info mii_if;
> };
>
> static int mdio_read(struct net_device *dev, int phy_id, int location);
> static void mdio_write(struct net_device *dev, int phy_id, int location, int value);
> static int rhine_open(struct net_device *dev);
> -static void rhine_check_duplex(struct net_device *dev);
> -static void rhine_timer(unsigned long data);
> static void rhine_tx_timeout(struct net_device *dev);
> static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev);
> static irqreturn_t rhine_interrupt(int irq, void *dev_instance, struct pt_regs *regs);
> @@ -1032,6 +1027,21 @@
> }
> }
>
> +static void rhine_check_media(struct net_device *dev, unsigned int init_media)
> +{
> + struct rhine_private *rp = netdev_priv(dev);
> + long ioaddr = dev->base_addr;
> +
> + mii_check_media(&rp->mii_if, debug, init_media);
> +
> + if (rp->mii_if.full_duplex)
> + writeb(readb(ioaddr + ChipCmd1) | Cmd1FDuplex,
> + ioaddr + ChipCmd1);
> + else
> + writeb(readb(ioaddr + ChipCmd1) & ~Cmd1FDuplex,
> + ioaddr + ChipCmd1);
> +}
> +
> static void init_registers(struct net_device *dev)
> {
> struct rhine_private *rp = netdev_priv(dev);
> @@ -1047,7 +1057,6 @@
> writeb(0x20, ioaddr + TxConfig);
> rp->tx_thresh = 0x20;
> rp->rx_thresh = 0x60; /* Written in rhine_set_rx_mode(). */
> - rp->mii_if.full_duplex = 0;
>
> writel(rp->rx_ring_dma, ioaddr + RxRingPtr);
> writel(rp->tx_ring_dma, ioaddr + TxRingPtr);
> @@ -1063,14 +1072,42 @@
>
> writew(CmdStart|CmdTxOn|CmdRxOn|(Cmd1NoTxPoll << 8),
> ioaddr + ChipCmd);
> - if (rp->mii_if.force_media)
> - writeb(readb(ioaddr + ChipCmd1) | Cmd1FDuplex,
> - ioaddr + ChipCmd1);
> - else
> - writeb(readb(ioaddr + ChipCmd1) & ~Cmd1FDuplex,
> - ioaddr + ChipCmd1);
> + rhine_check_media(dev, 1);
> +}
> +
> +/* Enable MII link status auto-polling (required for IntrLinkChange) */
> +static void rhine_enable_linkmon(long ioaddr)
> +{
> + writeb(0, ioaddr + MIICmd);
> + writeb(MII_BMSR, ioaddr + MIIRegAddr);
> + writeb(0x80, ioaddr + MIICmd);
>
> - rhine_check_duplex(dev);
> + RHINE_WAIT_FOR((readb(ioaddr + MIIRegAddr) & 0x20));
> +
> + writeb(MII_BMSR | 0x40, ioaddr + MIIRegAddr);
> +}
> +
> +/* Disable MII link status auto-polling (required for MDIO access) */
> +static void rhine_disable_linkmon(long ioaddr, u32 quirks)
> +{
> + writeb(0, ioaddr + MIICmd);
> +
> + if (quirks & rqRhineI) {
> + writeb(0x01, ioaddr + MIIRegAddr); // MII_BMSR
> +
> + /* Can be called from ISR. Evil. */
> + mdelay(1);
Net drivers are slowly moving towards schedule_work()/queue_work() for
doing "slow path" stuff like chip reset or MII phy stuff.
Jeff
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [7/9][PATCH 2.6] Media mode rewrite
2004-06-19 21:24 ` Jeff Garzik
@ 2004-06-19 22:20 ` Roger Luethi
0 siblings, 0 replies; 16+ messages in thread
From: Roger Luethi @ 2004-06-19 22:20 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, netdev
On Sat, 19 Jun 2004 17:24:32 -0400, Jeff Garzik wrote:
> >+ /* Can be called from ISR. Evil. */
> >+ mdelay(1);
>
>
> Net drivers are slowly moving towards schedule_work()/queue_work() for
> doing "slow path" stuff like chip reset or MII phy stuff.
I already have an item on my todo list to look at work queues. Glad to
hear that's where everyone's moving.
Roger
^ permalink raw reply [flat|nested] 16+ messages in thread
* [8/9][PATCH 2.6] Small fixes and clean-up
2004-06-15 17:47 [0/9] via-rhine: Major surgery Roger Luethi
` (5 preceding siblings ...)
2004-06-15 17:49 ` [7/9][PATCH 2.6] Media mode rewrite Roger Luethi
@ 2004-06-15 17:49 ` Roger Luethi
[not found] ` <40D4AFE1.6020508@pobox.com>
2004-06-15 17:50 ` [9/9][PATCH 2.6] Add WOL support Roger Luethi
` (2 subsequent siblings)
9 siblings, 1 reply; 16+ messages in thread
From: Roger Luethi @ 2004-06-15 17:49 UTC (permalink / raw)
To: Jeff Garzik, Andrew Morton; +Cc: netdev
Bump driver version to mark recent major changes in driver code.
Remove backoff parameter. The reason it was once introduced is gone.
Continue to go with EEPROM default for now, will hard-wire IEEE backoff
algorithm instead (later).
Rhine-I needs extra time to recuperate from chip reset before EEPROM
reload.
Add Rhine model identification.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
--- orig/drivers/net/via-rhine.c
+++ mod/drivers/net/via-rhine.c
@@ -125,11 +125,16 @@
LK1.1.19 (Roger Luethi)
- Increase Tx threshold for unspecified errors
+ LK1.2.0-2.6 (Roger Luethi)
+ - Massive clean-up
+ - Rewrite PHY, media handling (remove options, full_duplex, backoff)
+ - Fix Tx engine race for good
+
*/
#define DRV_NAME "via-rhine"
-#define DRV_VERSION "1.1.20-2.6"
-#define DRV_RELDATE "May-23-2004"
+#define DRV_VERSION "1.2.0-2.6"
+#define DRV_RELDATE "June-10-2004"
/* A few user-configurable values.
@@ -142,9 +147,6 @@
Setting to > 1518 effectively disables this feature. */
static int rx_copybreak;
-/* Select a backoff algorithm (Ethernet capture effect) */
-static int backoff;
-
/*
* In case you are looking for 'options[]' or 'full_duplex[]', they
* are gone. Use ethtool(8) instead.
@@ -207,9 +209,6 @@
static char version[] __devinitdata =
KERN_INFO DRV_NAME ".c:v1.10-LK" DRV_VERSION " " DRV_RELDATE " Written by Donald Becker\n";
-static char shortname[] = DRV_NAME;
-
-
/* This driver was written to use PCI memory space. Some early versions
of the Rhine may only work correctly with I/O space accesses. */
#ifdef CONFIG_VIA_RHINE_MMIO
@@ -236,11 +235,9 @@
MODULE_PARM(max_interrupt_work, "i");
MODULE_PARM(debug, "i");
MODULE_PARM(rx_copybreak, "i");
-MODULE_PARM(backoff, "i");
MODULE_PARM_DESC(max_interrupt_work, "VIA Rhine maximum events handled per interrupt");
MODULE_PARM_DESC(debug, "VIA Rhine debug level (0-7)");
MODULE_PARM_DESC(rx_copybreak, "VIA Rhine copy breakpoint for copy-only-tiny-frames");
-MODULE_PARM_DESC(backoff, "VIA Rhine: Bits 0-3: backoff algorithm");
/*
Theory of Operation
@@ -343,17 +340,18 @@
enum rhine_revs {
VT86C100A = 0x00,
+ VTunknown0 = 0x20,
VT6102 = 0x40,
VT8231 = 0x50, /* Integrated MAC */
VT8233 = 0x60, /* Integrated MAC */
VT8235 = 0x74, /* Integrated MAC */
VT8237 = 0x78, /* Integrated MAC */
- VTunknown0 = 0x7C,
+ VTunknown1 = 0x7C,
VT6105 = 0x80,
VT6105_B0 = 0x83,
VT6105L = 0x8A,
VT6107 = 0x8C,
- VTunknown1 = 0x8E,
+ VTunknown2 = 0x8E,
VT6105M = 0x90,
};
@@ -609,7 +607,7 @@
/*
* Loads bytes 0x00-0x05, 0x6E-0x6F, 0x78-0x7B from EEPROM
- * (plus 0x6C for Rhine I/II)
+ * (plus 0x6C for Rhine-I/II)
*/
static void __devinit rhine_reload_eeprom(long pioaddr, struct net_device *dev)
{
@@ -645,9 +643,15 @@
static void rhine_hw_init(struct net_device *dev, long pioaddr)
{
+ struct rhine_private *rp = netdev_priv(dev);
+
/* Reset the chip to erase previous misconfiguration. */
rhine_chip_reset(dev);
+ /* Rhine-I needs extra time to recuperate before EEPROM reload */
+ if (rp->quirks & rqRhineI)
+ msleep(5);
+
/* Reload EEPROM controlled bytes cleared by soft reset */
rhine_reload_eeprom(pioaddr, dev);
}
@@ -660,12 +664,11 @@
int i, rc;
u8 pci_rev;
u32 quirks;
- static int card_idx = -1;
long pioaddr;
long memaddr;
long ioaddr;
int io_size, phy_id;
- const char *name;
+ const char *name, *mname;
/* when built into the kernel, we only print version if device is found */
#ifndef MODULE
@@ -678,22 +681,43 @@
io_size = 256;
phy_id = 0;
- if (pci_rev < VT6102) {
+ quirks = 0;
+ name = "Rhine";
+ mname = "unknown";
+ if (pci_rev < VTunknown0) {
quirks = rqRhineI;
io_size = 128;
- name = "VT86C100A Rhine";
+ mname = "VT86C100A";
}
- else {
+ else if (pci_rev >= VT6102) {
quirks = rqWOL | rqForceReset;
if (pci_rev < VT6105) {
name = "Rhine II";
quirks |= rqStatusWBRace; /* Rhine-II exclusive */
+ if (pci_rev < VT8231)
+ mname = "VT6102";
+ else if (pci_rev < VT8233)
+ mname = "VT8231";
+ else if (pci_rev < VT8235)
+ mname = "VT8233";
+ else if (pci_rev < VT8237)
+ mname = "VT8235";
+ else if (pci_rev < VTunknown1)
+ mname = "VT8237";
}
else {
name = "Rhine III";
phy_id = 1; /* Integrated PHY, phy_id fixed to 1 */
if (pci_rev >= VT6105_B0)
quirks |= rq6patterns;
+ if (pci_rev < VT6105L)
+ mname = "VT6105";
+ else if (pci_rev < VT6107)
+ mname = "VT6105L";
+ else if (pci_rev < VT6105M)
+ mname = "VT6107";
+ else if (pci_rev >= VT6105M)
+ mname = "Management Adapter VT6105M";
}
}
@@ -722,17 +746,16 @@
pci_set_master(pdev);
- dev = alloc_etherdev(sizeof(*rp));
- if (dev == NULL) {
+ dev = alloc_etherdev(sizeof(struct rhine_private));
+ if (!dev) {
rc = -ENOMEM;
- printk(KERN_ERR "init_ethernet failed for card #%d\n",
- card_idx);
+ printk(KERN_ERR "alloc_etherdev failed\n");
goto err_out;
}
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &pdev->dev);
- rc = pci_request_regions(pdev, shortname);
+ rc = pci_request_regions(pdev, DRV_NAME);
if (rc)
goto err_out_free_netdev;
@@ -768,9 +791,8 @@
rp = netdev_priv(dev);
rp->quirks = quirks;
+ /* Get chip registers into a sane state */
rhine_power_init(dev);
-
- /* Reset the chip to erase previous misconfiguration. */
rhine_hw_init(dev, pioaddr);
for (i = 0; i < 6; i++)
@@ -778,16 +800,11 @@
if (!is_valid_ether_addr(dev->dev_addr)) {
rc = -EIO;
- printk(KERN_ERR "Invalid MAC address for card #%d\n", card_idx);
+ printk(KERN_ERR "Invalid MAC address\n");
goto err_out_unmap;
}
- /* Select backoff algorithm */
- if (backoff)
- writeb(readb(ioaddr + ConfigD) & (0xF0 | backoff),
- ioaddr + ConfigD);
-
- /* For Rhine I/II, phy_id is loaded from EEPROM */
+ /* For Rhine-I/II, phy_id is loaded from EEPROM */
if (!phy_id)
phy_id = readb(ioaddr + 0x6C);
@@ -822,8 +839,8 @@
if (rc)
goto err_out_unmap;
- printk(KERN_INFO "%s: VIA %s at 0x%lx, ",
- dev->name, name,
+ printk(KERN_INFO "%s: VIA %s (%s) at 0x%lx, ",
+ dev->name, name, mname,
#ifdef USE_MMIO
memaddr
#else
@@ -1070,7 +1087,7 @@
IntrPCIErr | IntrStatsMax | IntrLinkChange,
ioaddr + IntrEnable);
- writew(CmdStart|CmdTxOn|CmdRxOn|(Cmd1NoTxPoll << 8),
+ writew(CmdStart | CmdTxOn | CmdRxOn | (Cmd1NoTxPoll << 8),
ioaddr + ChipCmd);
rhine_check_media(dev, 1);
}
@@ -1142,7 +1159,7 @@
writeb(phy_id, ioaddr + MIIPhyAddr);
writeb(regnum, ioaddr + MIIRegAddr);
writew(value, ioaddr + MIIData);
- writeb(0x20, ioaddr + MIICmd); /* Trigger write. */
+ writeb(0x20, ioaddr + MIICmd); /* Trigger write */
RHINE_WAIT_FOR(!(readb(ioaddr + MIICmd) & 0x20));
rhine_enable_linkmon(ioaddr);
@@ -1152,20 +1169,20 @@
{
struct rhine_private *rp = netdev_priv(dev);
long ioaddr = dev->base_addr;
- int i;
+ int rc;
- i = request_irq(rp->pdev->irq, &rhine_interrupt, SA_SHIRQ, dev->name,
+ rc = request_irq(rp->pdev->irq, &rhine_interrupt, SA_SHIRQ, dev->name,
dev);
- if (i)
- return i;
+ if (rc)
+ return rc;
if (debug > 1)
printk(KERN_DEBUG "%s: rhine_open() irq %d.\n",
dev->name, rp->pdev->irq);
- i = alloc_ring(dev);
- if (i)
- return i;
+ rc = alloc_ring(dev);
+ if (rc)
+ return rc;
alloc_rbufs(dev);
alloc_tbufs(dev);
rhine_chip_reset(dev);
@@ -1482,10 +1499,6 @@
rp->rx_buf_sz,
PCI_DMA_FROMDEVICE);
- /* *_IP_COPYSUM isn't defined anywhere and
- eth_copy_and_sum is memcpy for all archs so
- this is kind of pointless right now
- ... or? */
eth_copy_and_sum(skb,
rp->rx_skbuff[entry]->tail,
pkt_len, 0);
@@ -1574,7 +1587,6 @@
ioaddr + ChipCmd);
writeb(readb(ioaddr + ChipCmd1) | Cmd1TxDemand,
ioaddr + ChipCmd1);
-
IOSYNC;
}
else {
@@ -1834,7 +1846,7 @@
static struct pci_driver rhine_driver = {
- .name = "via-rhine",
+ .name = DRV_NAME,
.id_table = rhine_pci_tbl,
.probe = rhine_init_one,
.remove = __devexit_p(rhine_remove_one),
^ permalink raw reply [flat|nested] 16+ messages in thread* [9/9][PATCH 2.6] Add WOL support
2004-06-15 17:47 [0/9] via-rhine: Major surgery Roger Luethi
` (6 preceding siblings ...)
2004-06-15 17:49 ` [8/9][PATCH 2.6] Small fixes and clean-up Roger Luethi
@ 2004-06-15 17:50 ` Roger Luethi
2004-06-19 21:29 ` Jeff Garzik
2004-06-16 15:03 ` [0/9] via-rhine: Major surgery Jeff Garzik
2004-06-19 21:20 ` Jeff Garzik
9 siblings, 1 reply; 16+ messages in thread
From: Roger Luethi @ 2004-06-15 17:50 UTC (permalink / raw)
To: Jeff Garzik, Andrew Morton; +Cc: netdev
Add rhine_shutdown callback to prepare Rhine power registers for
shutdown.
Add rhine_get_wol/rhine_set_wol for ethtool ioctl.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
--- 2.6-mm/drivers/net/via-rhine.c.orig 2004-06-15 18:34:21.000000000 +0200
+++ 2.6-mm/drivers/net/via-rhine.c 2004-06-15 18:36:12.000000000 +0200
@@ -394,8 +394,8 @@
ConfigA=0x78, ConfigB=0x79, ConfigC=0x7A, ConfigD=0x7B,
RxMissed=0x7C, RxCRCErrs=0x7E, MiscCmd=0x81,
StickyHW=0x83, IntrStatus2=0x84,
- WOLcrSet=0xA0, WOLcrClr=0xA4, WOLcrClr1=0xA6,
- WOLcgClr=0xA7,
+ WOLcrSet=0xA0, PwcfgSet=0xA1, WOLcgSet=0xA3, WOLcrClr=0xA4,
+ WOLcrClr1=0xA6, WOLcgClr=0xA7,
PwrcsrSet=0xA8, PwrcsrSet1=0xA9, PwrcsrClr=0xAC, PwrcsrClr1=0xAD,
};
@@ -427,6 +427,15 @@
IntrTxErrSummary=0x082218,
};
+/* Bits in WOLcrSet/WOLcrClr and PwrcsrSet/PwrcsrClr */
+enum wol_bits {
+ WOLucast = 0x10,
+ WOLmagic = 0x20,
+ WOLbmcast = 0x30,
+ WOLlnkon = 0x40,
+ WOLlnkoff = 0x80,
+};
+
/* The Rx and Tx buffer descriptors. */
struct rx_desc {
s32 rx_status;
@@ -491,8 +500,8 @@
unsigned int cur_rx, dirty_rx; /* Producer/consumer ring indices */
unsigned int cur_tx, dirty_tx;
unsigned int rx_buf_sz; /* Based on MTU+slack. */
+ u8 wolopts;
- /* These values are keep track of the transceiver/media in use. */
u8 tx_thresh, rx_thresh;
struct mii_if_info mii_if;
@@ -512,6 +521,7 @@
static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
static struct ethtool_ops netdev_ethtool_ops;
static int rhine_close(struct net_device *dev);
+static void rhine_shutdown (struct device *gdev);
#define RHINE_WAIT_FOR(condition) do { \
int i=1024; \
@@ -537,12 +547,13 @@
/*
* Get power related registers into sane state.
- * Returns content of power-event (WOL) registers.
+ * Notify user about past WOL event.
*/
static void rhine_power_init(struct net_device *dev)
{
long ioaddr = dev->base_addr;
struct rhine_private *rp = netdev_priv(dev);
+ u16 wolstat;
if (rp->quirks & rqWOL) {
/* Make sure chip is in power state D0 */
@@ -557,10 +568,40 @@
if (rp->quirks & rq6patterns)
writeb(0x03, ioaddr + WOLcrClr1);
+ /* Save power-event status bits */
+ wolstat = readb(ioaddr + PwrcsrSet);
+ if (rp->quirks & rq6patterns)
+ wolstat |= (readb(ioaddr + PwrcsrSet1) & 0x03) << 8;
+
/* Clear power-event status bits */
writeb(0xFF, ioaddr + PwrcsrClr);
if (rp->quirks & rq6patterns)
writeb(0x03, ioaddr + PwrcsrClr1);
+
+ if (wolstat) {
+ char *reason;
+ switch (wolstat) {
+ case WOLmagic:
+ reason = "Magic packet";
+ break;
+ case WOLlnkon:
+ reason = "Link went up";
+ break;
+ case WOLlnkoff:
+ reason = "Link went down";
+ break;
+ case WOLucast:
+ reason = "Unicast packet";
+ break;
+ case WOLbmcast:
+ reason = "Multicast/broadcast packet";
+ break;
+ default:
+ reason = "Unknown";
+ }
+ printk("%s: Woke system up. Reason: %s.\n",
+ DRV_NAME, reason);
+ }
}
}
@@ -1766,6 +1807,39 @@
debug = value;
}
+static void rhine_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+ struct rhine_private *rp = netdev_priv(dev);
+
+ if (!(rp->quirks & rqWOL))
+ return;
+
+ spin_lock_irq(&rp->lock);
+ wol->supported = WAKE_PHY | WAKE_MAGIC |
+ WAKE_UCAST | WAKE_MCAST | WAKE_BCAST; /* Untested */
+ wol->wolopts = rp->wolopts;
+ spin_unlock_irq(&rp->lock);
+}
+
+static int rhine_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+ struct rhine_private *rp = netdev_priv(dev);
+ u32 support = WAKE_PHY | WAKE_MAGIC |
+ WAKE_UCAST | WAKE_MCAST | WAKE_BCAST; /* Untested */
+
+ if (!(rp->quirks & rqWOL))
+ return -EINVAL;
+
+ if (wol->wolopts & ~support)
+ return -EINVAL;
+
+ spin_lock_irq(&rp->lock);
+ rp->wolopts = wol->wolopts;
+ spin_unlock_irq(&rp->lock);
+
+ return 0;
+}
+
static struct ethtool_ops netdev_ethtool_ops = {
.get_drvinfo = netdev_get_drvinfo,
.get_settings = netdev_get_settings,
@@ -1774,6 +1848,8 @@
.get_link = netdev_get_link,
.get_msglevel = netdev_get_msglevel,
.set_msglevel = netdev_set_msglevel,
+ .get_wol = rhine_get_wol,
+ .set_wol = rhine_set_wol,
.get_sg = ethtool_op_get_sg,
.get_tx_csum = ethtool_op_get_tx_csum,
};
@@ -1844,12 +1920,51 @@
pci_set_drvdata(pdev, NULL);
}
+static void rhine_shutdown (struct device *gendev)
+{
+ struct pci_dev *pdev = to_pci_dev(gendev);
+ struct net_device *dev = pci_get_drvdata(pdev);
+ struct rhine_private *rp = netdev_priv(dev);
+
+ long ioaddr = dev->base_addr;
+
+ rhine_power_init(dev);
+
+ /* Make sure we use pattern 0, 1 and not 4, 5 */
+ if (rp->quirks & rq6patterns)
+ writeb(0x04, ioaddr + 0xA7);
+
+ if (rp->wolopts & WAKE_MAGIC)
+ writeb(WOLmagic, ioaddr + WOLcrSet);
+
+ if (rp->wolopts & (WAKE_BCAST|WAKE_MCAST))
+ writeb(WOLbmcast, ioaddr + WOLcgSet);
+
+ if (rp->wolopts & WAKE_PHY)
+ writeb(WOLlnkon | WOLlnkoff, ioaddr + WOLcrSet);
+
+ if (rp->wolopts & WAKE_UCAST)
+ writeb(WOLucast, ioaddr + WOLcrSet);
+
+ /* Enable legacy WOL (for old motherboards) */
+ writeb(0x01, ioaddr + PwcfgSet);
+ writeb(readb(ioaddr + StickyHW) | 0x04, ioaddr + StickyHW);
+
+ /* Hit power state D3 (sleep) */
+ writeb(readb(ioaddr + StickyHW) | 0x03, ioaddr + StickyHW);
+
+ /* TODO: Check use of pci_enable_wake() */
+
+}
static struct pci_driver rhine_driver = {
.name = DRV_NAME,
.id_table = rhine_pci_tbl,
.probe = rhine_init_one,
.remove = __devexit_p(rhine_remove_one),
+ .driver = {
+ .shutdown = rhine_shutdown,
+ }
};
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [9/9][PATCH 2.6] Add WOL support
2004-06-15 17:50 ` [9/9][PATCH 2.6] Add WOL support Roger Luethi
@ 2004-06-19 21:29 ` Jeff Garzik
2004-06-19 22:15 ` Roger Luethi
0 siblings, 1 reply; 16+ messages in thread
From: Jeff Garzik @ 2004-06-19 21:29 UTC (permalink / raw)
To: Roger Luethi; +Cc: Andrew Morton, netdev
Roger Luethi wrote:
> Add rhine_shutdown callback to prepare Rhine power registers for
> shutdown.
>
> Add rhine_get_wol/rhine_set_wol for ethtool ioctl.
>
> Signed-off-by: Roger Luethi <rl@hellgate.ch>
>
> --- 2.6-mm/drivers/net/via-rhine.c.orig 2004-06-15 18:34:21.000000000 +0200
> +++ 2.6-mm/drivers/net/via-rhine.c 2004-06-15 18:36:12.000000000 +0200
> @@ -394,8 +394,8 @@
> ConfigA=0x78, ConfigB=0x79, ConfigC=0x7A, ConfigD=0x7B,
> RxMissed=0x7C, RxCRCErrs=0x7E, MiscCmd=0x81,
> StickyHW=0x83, IntrStatus2=0x84,
> - WOLcrSet=0xA0, WOLcrClr=0xA4, WOLcrClr1=0xA6,
> - WOLcgClr=0xA7,
> + WOLcrSet=0xA0, PwcfgSet=0xA1, WOLcgSet=0xA3, WOLcrClr=0xA4,
> + WOLcrClr1=0xA6, WOLcgClr=0xA7,
> PwrcsrSet=0xA8, PwrcsrSet1=0xA9, PwrcsrClr=0xAC, PwrcsrClr1=0xAD,
> };
>
> @@ -427,6 +427,15 @@
> IntrTxErrSummary=0x082218,
> };
>
> +/* Bits in WOLcrSet/WOLcrClr and PwrcsrSet/PwrcsrClr */
> +enum wol_bits {
> + WOLucast = 0x10,
> + WOLmagic = 0x20,
> + WOLbmcast = 0x30,
> + WOLlnkon = 0x40,
> + WOLlnkoff = 0x80,
> +};
> +
> /* The Rx and Tx buffer descriptors. */
> struct rx_desc {
> s32 rx_status;
> @@ -491,8 +500,8 @@
> unsigned int cur_rx, dirty_rx; /* Producer/consumer ring indices */
> unsigned int cur_tx, dirty_tx;
> unsigned int rx_buf_sz; /* Based on MTU+slack. */
> + u8 wolopts;
>
> - /* These values are keep track of the transceiver/media in use. */
> u8 tx_thresh, rx_thresh;
>
> struct mii_if_info mii_if;
> @@ -512,6 +521,7 @@
> static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
> static struct ethtool_ops netdev_ethtool_ops;
> static int rhine_close(struct net_device *dev);
> +static void rhine_shutdown (struct device *gdev);
>
> #define RHINE_WAIT_FOR(condition) do { \
> int i=1024; \
> @@ -537,12 +547,13 @@
>
> /*
> * Get power related registers into sane state.
> - * Returns content of power-event (WOL) registers.
> + * Notify user about past WOL event.
> */
> static void rhine_power_init(struct net_device *dev)
> {
> long ioaddr = dev->base_addr;
> struct rhine_private *rp = netdev_priv(dev);
> + u16 wolstat;
>
> if (rp->quirks & rqWOL) {
> /* Make sure chip is in power state D0 */
> @@ -557,10 +568,40 @@
> if (rp->quirks & rq6patterns)
> writeb(0x03, ioaddr + WOLcrClr1);
>
> + /* Save power-event status bits */
> + wolstat = readb(ioaddr + PwrcsrSet);
> + if (rp->quirks & rq6patterns)
> + wolstat |= (readb(ioaddr + PwrcsrSet1) & 0x03) << 8;
> +
> /* Clear power-event status bits */
> writeb(0xFF, ioaddr + PwrcsrClr);
> if (rp->quirks & rq6patterns)
> writeb(0x03, ioaddr + PwrcsrClr1);
> +
> + if (wolstat) {
> + char *reason;
> + switch (wolstat) {
> + case WOLmagic:
> + reason = "Magic packet";
> + break;
> + case WOLlnkon:
> + reason = "Link went up";
> + break;
> + case WOLlnkoff:
> + reason = "Link went down";
> + break;
> + case WOLucast:
> + reason = "Unicast packet";
> + break;
> + case WOLbmcast:
> + reason = "Multicast/broadcast packet";
> + break;
> + default:
> + reason = "Unknown";
> + }
> + printk("%s: Woke system up. Reason: %s.\n",
> + DRV_NAME, reason);
printk needs KERN_xxx prefix
also, use dev->name rather than DRV_NAME, since we are past the probe phase.
> + }
> }
> }
>
> @@ -1766,6 +1807,39 @@
> debug = value;
> }
>
> +static void rhine_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
> +{
> + struct rhine_private *rp = netdev_priv(dev);
> +
> + if (!(rp->quirks & rqWOL))
> + return;
is WOL really considered a quirk? ;-)
> + spin_lock_irq(&rp->lock);
> + wol->supported = WAKE_PHY | WAKE_MAGIC |
> + WAKE_UCAST | WAKE_MCAST | WAKE_BCAST; /* Untested */
> + wol->wolopts = rp->wolopts;
> + spin_unlock_irq(&rp->lock);
> +}
> +
> +static int rhine_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
> +{
> + struct rhine_private *rp = netdev_priv(dev);
> + u32 support = WAKE_PHY | WAKE_MAGIC |
> + WAKE_UCAST | WAKE_MCAST | WAKE_BCAST; /* Untested */
> +
> + if (!(rp->quirks & rqWOL))
> + return -EINVAL;
> +
> + if (wol->wolopts & ~support)
> + return -EINVAL;
> +
> + spin_lock_irq(&rp->lock);
> + rp->wolopts = wol->wolopts;
> + spin_unlock_irq(&rp->lock);
> +
> + return 0;
> +}
> +
> static struct ethtool_ops netdev_ethtool_ops = {
> .get_drvinfo = netdev_get_drvinfo,
> .get_settings = netdev_get_settings,
> @@ -1774,6 +1848,8 @@
> .get_link = netdev_get_link,
> .get_msglevel = netdev_get_msglevel,
> .set_msglevel = netdev_set_msglevel,
> + .get_wol = rhine_get_wol,
> + .set_wol = rhine_set_wol,
> .get_sg = ethtool_op_get_sg,
> .get_tx_csum = ethtool_op_get_tx_csum,
> };
> @@ -1844,12 +1920,51 @@
> pci_set_drvdata(pdev, NULL);
> }
>
> +static void rhine_shutdown (struct device *gendev)
> +{
> + struct pci_dev *pdev = to_pci_dev(gendev);
> + struct net_device *dev = pci_get_drvdata(pdev);
> + struct rhine_private *rp = netdev_priv(dev);
> +
> + long ioaddr = dev->base_addr;
> +
> + rhine_power_init(dev);
> +
> + /* Make sure we use pattern 0, 1 and not 4, 5 */
> + if (rp->quirks & rq6patterns)
> + writeb(0x04, ioaddr + 0xA7);
> +
> + if (rp->wolopts & WAKE_MAGIC)
> + writeb(WOLmagic, ioaddr + WOLcrSet);
> +
> + if (rp->wolopts & (WAKE_BCAST|WAKE_MCAST))
> + writeb(WOLbmcast, ioaddr + WOLcgSet);
> +
> + if (rp->wolopts & WAKE_PHY)
> + writeb(WOLlnkon | WOLlnkoff, ioaddr + WOLcrSet);
> +
> + if (rp->wolopts & WAKE_UCAST)
> + writeb(WOLucast, ioaddr + WOLcrSet);
> +
> + /* Enable legacy WOL (for old motherboards) */
> + writeb(0x01, ioaddr + PwcfgSet);
> + writeb(readb(ioaddr + StickyHW) | 0x04, ioaddr + StickyHW);
> +
> + /* Hit power state D3 (sleep) */
> + writeb(readb(ioaddr + StickyHW) | 0x03, ioaddr + StickyHW);
would be nice to eliminate these magic numbers (0x04, 0x04), ...
> + /* TODO: Check use of pci_enable_wake() */
> +
> +}
>
> static struct pci_driver rhine_driver = {
> .name = DRV_NAME,
> .id_table = rhine_pci_tbl,
> .probe = rhine_init_one,
> .remove = __devexit_p(rhine_remove_one),
> + .driver = {
> + .shutdown = rhine_shutdown,
> + }
> };
>
>
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [9/9][PATCH 2.6] Add WOL support
2004-06-19 21:29 ` Jeff Garzik
@ 2004-06-19 22:15 ` Roger Luethi
0 siblings, 0 replies; 16+ messages in thread
From: Roger Luethi @ 2004-06-19 22:15 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, netdev
On Sat, 19 Jun 2004 17:29:45 -0400, Jeff Garzik wrote:
> >+ reason = "Unicast packet";
> >+ break;
> >+ case WOLbmcast:
> >+ reason = "Multicast/broadcast packet";
> >+ break;
> >+ default:
> >+ reason = "Unknown";
> >+ }
> >+ printk("%s: Woke system up. Reason: %s.\n",
> >+ DRV_NAME, reason);
>
> printk needs KERN_xxx prefix
Oops. Fixed.
> also, use dev->name rather than DRV_NAME, since we are past the probe phase.
Can you define probe phase? ... In the code as is, we haven't called
register_netdev when we execute that part. Getting the probe stuff into
a sane order is on my todo list as well, but ISTR that calling
register_netdev way early is frowned upon. No?
> >+ /* Enable legacy WOL (for old motherboards) */
> >+ writeb(0x01, ioaddr + PwcfgSet);
> >+ writeb(readb(ioaddr + StickyHW) | 0x04, ioaddr + StickyHW);
> >+
> >+ /* Hit power state D3 (sleep) */
> >+ writeb(readb(ioaddr + StickyHW) | 0x03, ioaddr + StickyHW);
>
> would be nice to eliminate these magic numbers (0x04, 0x04), ...
Mostly agreed. I want to change a bunch of symbol names anyway. However,
I found it easier to document magic numbers that are used only _once_
where they occur instead of giving them a name I have to look up later.
I don't feel strongly about it, though, so feel free to bug me again if
you do :-).
Roger
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [0/9] via-rhine: Major surgery
2004-06-15 17:47 [0/9] via-rhine: Major surgery Roger Luethi
` (7 preceding siblings ...)
2004-06-15 17:50 ` [9/9][PATCH 2.6] Add WOL support Roger Luethi
@ 2004-06-16 15:03 ` Jeff Garzik
2004-06-19 21:20 ` Jeff Garzik
9 siblings, 0 replies; 16+ messages in thread
From: Jeff Garzik @ 2004-06-16 15:03 UTC (permalink / raw)
To: Roger Luethi; +Cc: Andrew Morton, netdev
Roger Luethi wrote:
> This set of patches obsoletes all via-rhine patches for 2.6 that didn't
> make it into 2.6.7-rc3-mm2. Most notable changes: I rewrote the media,
> PHY, and link state handling and added WOL support for Rhine chips.
>
> Patches [1/9] and [2/9] are resends so you won't have to go hunt them
> down before trying the rest.
>
> These patches need review and testing, especially from people with
> WOL-capable hardware.
Cool. I'll review and get into netdev-2.6 (and thus -mm) in the next
24-48 hrs...
Jeff
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [0/9] via-rhine: Major surgery
2004-06-15 17:47 [0/9] via-rhine: Major surgery Roger Luethi
` (8 preceding siblings ...)
2004-06-16 15:03 ` [0/9] via-rhine: Major surgery Jeff Garzik
@ 2004-06-19 21:20 ` Jeff Garzik
9 siblings, 0 replies; 16+ messages in thread
From: Jeff Garzik @ 2004-06-19 21:20 UTC (permalink / raw)
To: Roger Luethi; +Cc: Andrew Morton, netdev
all 9 patches applied to netdev-2.6 (and auto-propagated to Andrew's -mm
tree).
Will push to Linus after comments are resolved.
^ permalink raw reply [flat|nested] 16+ messages in thread