From: domen@coderock.org
To: jgarzik@pobox.com
Cc: netdev@oss.sgi.com, domen@coderock.org, nacc@us.ibm.com,
janitor@sternwelten.at
Subject: [patch 06/19] net/xirc2ps_cs: replace Wait() with msleep()
Date: Wed, 12 Jan 2005 00:10:24 +0100 [thread overview]
Message-ID: <20050111231024.CEF821F228@trashy.coderock.org> (raw)
Any comments would be appreciated.
Description: Use msleep() instead of Wait() to guarantee the task delays
as expected. Remove definition of Wait().
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
---
kj-domen/drivers/net/pcmcia/xirc2ps_cs.c | 23 +++++++++--------------
1 files changed, 9 insertions(+), 14 deletions(-)
diff -puN drivers/net/pcmcia/xirc2ps_cs.c~msleep-drivers_net_irda_pcmcia_xirc2ps_cs drivers/net/pcmcia/xirc2ps_cs.c
--- kj/drivers/net/pcmcia/xirc2ps_cs.c~msleep-drivers_net_irda_pcmcia_xirc2ps_cs 2005-01-10 18:00:00.000000000 +0100
+++ kj-domen/drivers/net/pcmcia/xirc2ps_cs.c 2005-01-10 18:00:00.000000000 +0100
@@ -418,11 +418,6 @@ next_tuple(client_handle_t handle, tuple
#define PutByte(reg,value) outb((value), ioaddr+(reg))
#define PutWord(reg,value) outw((value), ioaddr+(reg))
-#define Wait(n) do { \
- set_current_state(TASK_UNINTERRUPTIBLE); \
- schedule_timeout(n); \
-} while (0)
-
/*====== Functions used for debugging =================================*/
#if defined(PCMCIA_DEBUG) && 0 /* reading regs may change system status */
static void
@@ -1716,12 +1711,12 @@ hardreset(struct net_device *dev)
SelectPage(4);
udelay(1);
PutByte(XIRCREG4_GPR1, 0); /* clear bit 0: power down */
- Wait(HZ/25); /* wait 40 msec */
+ msleep(40); /* wait 40 msec */
if (local->mohawk)
PutByte(XIRCREG4_GPR1, 1); /* set bit 0: power up */
else
PutByte(XIRCREG4_GPR1, 1 | 4); /* set bit 0: power up, bit 2: AIC */
- Wait(HZ/50); /* wait 20 msec */
+ msleep(20); /* wait 20 msec */
}
static void
@@ -1735,9 +1730,9 @@ do_reset(struct net_device *dev, int ful
hardreset(dev);
PutByte(XIRCREG_CR, SoftReset); /* set */
- Wait(HZ/50); /* wait 20 msec */
+ msleep(20); /* wait 20 msec */
PutByte(XIRCREG_CR, 0); /* clear */
- Wait(HZ/25); /* wait 40 msec */
+ msleep(40); /* wait 40 msec */
if (local->mohawk) {
SelectPage(4);
/* set pin GP1 and GP2 to output (0x0c)
@@ -1748,7 +1743,7 @@ do_reset(struct net_device *dev, int ful
}
/* give the circuits some time to power up */
- Wait(HZ/2); /* about 500ms */
+ msleep(500); /* about 500ms */
local->last_ptr_value = 0;
local->silicon = local->mohawk ? (GetByte(XIRCREG4_BOV) & 0x70) >> 4
@@ -1767,7 +1762,7 @@ do_reset(struct net_device *dev, int ful
SelectPage(0x42);
PutByte(XIRCREG42_SWC1, 0x80);
}
- Wait(HZ/25); /* wait 40 msec to let it complete */
+ msleep(40); /* wait 40 msec to let it complete */
#ifdef PCMCIA_DEBUG
if (pc_debug) {
@@ -1826,7 +1821,7 @@ do_reset(struct net_device *dev, int ful
printk(KERN_INFO "%s: MII selected\n", dev->name);
SelectPage(2);
PutByte(XIRCREG2_MSR, GetByte(XIRCREG2_MSR) | 0x08);
- Wait(HZ/50);
+ msleep(20);
} else {
printk(KERN_INFO "%s: MII detected; using 10mbs\n",
dev->name);
@@ -1835,7 +1830,7 @@ do_reset(struct net_device *dev, int ful
PutByte(XIRCREG42_SWC1, 0xC0);
else /* enable 10BaseT */
PutByte(XIRCREG42_SWC1, 0x80);
- Wait(HZ/25); /* wait 40 msec to let it complete */
+ msleep(40); /* wait 40 msec to let it complete */
}
if (full_duplex)
PutByte(XIRCREG1_ECR, GetByte(XIRCREG1_ECR | FullDuplex));
@@ -1928,7 +1923,7 @@ init_mii(struct net_device *dev)
* Fixme: Better to use a timer here!
*/
for (i=0; i < 35; i++) {
- Wait(HZ/10); /* wait 100 msec */
+ msleep(100); /* wait 100 msec */
status = mii_rd(ioaddr, 0, 1);
if ((status & 0x0020) && (status & 0x0004))
break;
_
reply other threads:[~2005-01-11 23:10 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20050111231024.CEF821F228@trashy.coderock.org \
--to=domen@coderock.org \
--cc=janitor@sternwelten.at \
--cc=jgarzik@pobox.com \
--cc=nacc@us.ibm.com \
--cc=netdev@oss.sgi.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).