* [RFC: 2.6 patch] remove drivers/net/hydra.h
[not found] <200604041528.00142.ciaranfarrell@babelworx.net>
@ 2006-04-04 16:29 ` Adrian Bunk
2006-04-04 16:49 ` Geert Uytterhoeven
0 siblings, 1 reply; 2+ messages in thread
From: Adrian Bunk @ 2006-04-04 16:29 UTC (permalink / raw)
To: Ciaran Farrell; +Cc: linux-kernel, netdev, jgarzik, linux-m68k
On Tue, Apr 04, 2006 at 03:27:59PM +0200, Ciaran Farrell wrote:
> We were discussing this topic again and thought it should be reported here. As
> you are probably aware, the file
>
> linux-2.6.16.tar.bz2/linux-2.6.16/drivers/net/hydra.h
>
> contains a BSD 4 license.
>...
The interesting point is that the file seems to be complete unused.
Are there any objections against the patch below to simply remove it?
> cheers
>
> CFarrell
cu
Adrian
<-- snip -->
This patch removes drivers/net/hydra.h that is both unused and covered
by a 4 clause BSD licence (not by the UCB).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
---
drivers/net/hydra.h | 177 --------------------------------------------
1 file changed, 177 deletions(-)
--- linux-2.6.17-rc1-mm1-full/drivers/net/hydra.h 2006-03-20 06:53:29.000000000 +0100
+++ /dev/null 2006-02-12 01:05:26.000000000 +0100
@@ -1,177 +0,0 @@
-/* $Linux: hydra.h,v 1.0 1994/10/26 02:03:47 cgd Exp $ */
-
-/*
- * Copyright (c) 1994 Timo Rossi
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * 3. All advertising materials mentioning features or use of this software
- * must display the following acknowledgement:
- * This product includes software developed by Timo Rossi
- * 4. The name of the author may not be used to endorse or promote products
- * derived from this software without specific prior written permission
- *
- * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
- * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
- * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-/*
- * The Hydra Systems card uses the National Semiconductor
- * 8390 NIC (Network Interface Controller) chip, located
- * at card base address + 0xffe1. NIC registers are accessible
- * only at odd byte addresses, so the register offsets must
- * be multiplied by two.
- *
- * Card address PROM is located at card base + 0xffc0 (even byte addresses)
- *
- * RAM starts at the card base address, and is 16K or 64K.
- * The current Amiga NetBSD hydra driver is hardwired for 16K.
- * It seems that the RAM should be accessed as words or longwords only.
- *
- */
-
-/* adapted for Linux by Topi Kanerva 03/29/95
- with original author's permission */
-
-#define HYDRA_NIC_BASE 0xffe1
-
-/* Page0 registers */
-
-#define NIC_CR 0 /* Command register */
-#define NIC_PSTART (1*2) /* Page start (write) */
-#define NIC_PSTOP (2*2) /* Page stop (write) */
-#define NIC_BNDRY (3*2) /* Boundary pointer */
-#define NIC_TSR (4*2) /* Transmit status (read) */
-#define NIC_TPSR (4*2) /* Transmit page start (write) */
-#define NIC_NCR (5*2) /* Number of collisions, read */
-#define NIC_TBCR0 (5*2) /* Transmit byte count low (write) */
-#define NIC_FIFO (6*2) /* FIFO reg. (read) */
-#define NIC_TBCR1 (6*2) /* Transmit byte count high (write) */
-#define NIC_ISR (7*2) /* Interrupt status register */
-#define NIC_RBCR0 (0xa*2) /* Remote byte count low (write) */
-#define NIC_RBCR1 (0xb*2) /* Remote byte count high (write) */
-#define NIC_RSR (0xc*2) /* Receive status (read) */
-#define NIC_RCR (0xc*2) /* Receive config (write) */
-#define NIC_CNTR0 (0xd*2) /* Frame alignment error count (read) */
-#define NIC_TCR (0xd*2) /* Transmit config (write) */
-#define NIC_CNTR1 (0xe*2) /* CRC error counter (read) */
-#define NIC_DCR (0xe*2) /* Data config (write) */
-#define NIC_CNTR2 (0xf*2) /* missed packet counter (read) */
-#define NIC_IMR (0xf*2) /* Interrupt mask reg. (write) */
-
-/* Page1 registers */
-
-#define NIC_PAR0 (1*2) /* Physical address */
-#define NIC_PAR1 (2*2)
-#define NIC_PAR2 (3*2)
-#define NIC_PAR3 (4*2)
-#define NIC_PAR4 (5*2)
-#define NIC_PAR5 (6*2)
-#define NIC_CURR (7*2) /* Current RX ring-buffer page */
-#define NIC_MAR0 (8*2) /* Multicast address */
-#define NIC_MAR1 (9*2)
-#define NIC_MAR2 (0xa*2)
-#define NIC_MAR3 (0xb*2)
-#define NIC_MAR4 (0xc*2)
-#define NIC_MAR5 (0xd*2)
-#define NIC_MAR6 (0xe*2)
-#define NIC_MAR7 (0xf*2)
-
-/* Command register definitions */
-
-#define CR_STOP 0x01 /* Stop -- software reset command */
-#define CR_START 0x02 /* Start */
-#define CR_TXP 0x04 /* Transmit packet */
-
-#define CR_RD0 0x08 /* Remote DMA cmd */
-#define CR_RD1 0x10
-#define CR_RD2 0x20
-
-#define CR_NODMA CR_RD2
-
-#define CR_PS0 0x40 /* Page select */
-#define CR_PS1 0x80
-
-#define CR_PAGE0 0
-#define CR_PAGE1 CR_PS0
-#define CR_PAGE2 CR_PS1
-
-/* Interrupt status reg. definitions */
-
-#define ISR_PRX 0x01 /* Packet received without errors */
-#define ISR_PTX 0x02 /* Packet transmitted without errors */
-#define ISR_RXE 0x04 /* Receive error */
-#define ISR_TXE 0x08 /* Transmit error */
-#define ISR_OVW 0x10 /* Ring buffer overrun */
-#define ISR_CNT 0x20 /* Counter overflow */
-#define ISR_RDC 0x40 /* Remote DMA compile */
-#define ISR_RST 0x80 /* Reset status */
-
-/* Data config reg. definitions */
-
-#define DCR_WTS 0x01 /* Word transfer select */
-#define DCR_BOS 0x02 /* Byte order select */
-#define DCR_LAS 0x04 /* Long address select */
-#define DCR_LS 0x08 /* Loopback select */
-#define DCR_AR 0x10 /* Auto-init remote */
-#define DCR_FT0 0x20 /* FIFO threshold select */
-#define DCR_FT1 0x40
-
-/* Transmit config reg. definitions */
-
-#define TCR_CRC 0x01 /* Inhibit CRC */
-#define TCR_LB0 0x02 /* Loopback control */
-#define TCR_LB1 0x04
-#define TCR_ATD 0x08 /* Auto transmit disable */
-#define TCR_OFST 0x10 /* Collision offset enable */
-
-/* Transmit status reg. definitions */
-
-#define TSR_PTX 0x01 /* Packet transmitted */
-#define TSR_COL 0x04 /* Transmit collided */
-#define TSR_ABT 0x08 /* Transmit aborted */
-#define TSR_CRS 0x10 /* Carrier sense lost */
-#define TSR_FU 0x20 /* FIFO underrun */
-#define TSR_CDH 0x40 /* CD Heartbeat */
-#define TSR_OWC 0x80 /* Out of Window Collision */
-
-/* Receiver config register definitions */
-
-#define RCR_SEP 0x01 /* Save errored packets */
-#define RCR_AR 0x02 /* Accept runt packets */
-#define RCR_AB 0x04 /* Accept broadcast */
-#define RCR_AM 0x08 /* Accept multicast */
-#define RCR_PRO 0x10 /* Promiscuous mode */
-#define RCR_MON 0x20 /* Monitor mode */
-
-/* Receiver status register definitions */
-
-#define RSR_PRX 0x01 /* Packet received without error */
-#define RSR_CRC 0x02 /* CRC error */
-#define RSR_FAE 0x04 /* Frame alignment error */
-#define RSR_FO 0x08 /* FIFO overrun */
-#define RSR_MPA 0x10 /* Missed packet */
-#define RSR_PHY 0x20 /* Physical address */
-#define RSR_DIS 0x40 /* Received disabled */
-#define RSR_DFR 0x80 /* Deferring (jabber) */
-
-/* Hydra System card address PROM offset */
-
-#define HYDRA_ADDRPROM 0xffc0
-
-
^ permalink raw reply [flat|nested] 2+ messages in thread