* Re: Linux v2.6.17-rc4
[not found] <Pine.LNX.4.64.0605111640010.3866@g5.osdl.org>
@ 2006-05-12 10:24 ` Erik Mouw
2006-05-12 10:44 ` Michael Buesch
2006-05-12 21:19 ` Alistair John Strachan
1 sibling, 1 reply; 10+ messages in thread
From: Erik Mouw @ 2006-05-12 10:24 UTC (permalink / raw)
To: Linus Torvalds; +Cc: Linux Kernel Mailing List, netdev
On Thu, May 11, 2006 at 04:44:03PM -0700, Linus Torvalds wrote:
> Ok, I've let the release time between -rc's slide a bit too much again,
> but -rc4 is out there, and this is the time to hunker down for 2.6.17.
>
> If you know of any regressions, please holler now, so that we don't miss
> them.
I got assertion failures in the bcm43xx driver:
bcm43xx: Chip ID 0x4318, rev 0x2
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243, enabled
bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243, disabled
bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243, enabled
bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243, enabled
bcm43xx: PHY connected
bcm43xx: Detected PHY: Version: 3, Type 2, Revision 7
bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev: 8)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
bcm43xx: PHY connected
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: DMA initialized
bcm43xx: 80211 cores initialized
bcm43xx: Keys cleared
ADDRCONF(NETDEV_UP): eth2: link is not ready
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
ieee80211_crypt: registered algorithm 'WEP'
Erik
--
+-- Erik Mouw -- www.harddisk-recovery.com -- +31 70 370 12 90 --
| Lab address: Delftechpark 26, 2628 XH, Delft, The Netherlands
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Linux v2.6.17-rc4
2006-05-12 10:24 ` Linux v2.6.17-rc4 Erik Mouw
@ 2006-05-12 10:44 ` Michael Buesch
2006-05-12 11:23 ` Olaf Hering
2006-05-12 11:47 ` Erik Mouw
0 siblings, 2 replies; 10+ messages in thread
From: Michael Buesch @ 2006-05-12 10:44 UTC (permalink / raw)
To: Erik Mouw; +Cc: Linux Kernel Mailing List, netdev, Linus Torvalds
On Friday 12 May 2006 12:24, you wrote:
> On Thu, May 11, 2006 at 04:44:03PM -0700, Linus Torvalds wrote:
> > Ok, I've let the release time between -rc's slide a bit too much again,
> > but -rc4 is out there, and this is the time to hunker down for 2.6.17.
> >
> > If you know of any regressions, please holler now, so that we don't miss
> > them.
>
> I got assertion failures in the bcm43xx driver:
>
> bcm43xx: Chip ID 0x4318, rev 0x2
That is expected an non-fatal.
It is no regression.
We are working on it, but there won't be any fix for 2.6.17, as
very intrusive changes are needed to fix this.
--
Greetings Michael.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Linux v2.6.17-rc4
2006-05-12 10:44 ` Michael Buesch
@ 2006-05-12 11:23 ` Olaf Hering
2006-05-12 20:54 ` Michael Buesch
2006-05-12 11:47 ` Erik Mouw
1 sibling, 1 reply; 10+ messages in thread
From: Olaf Hering @ 2006-05-12 11:23 UTC (permalink / raw)
To: Michael Buesch; +Cc: Erik Mouw, netdev
On Fri, May 12, Michael Buesch wrote:
> On Friday 12 May 2006 12:24, you wrote:
> > On Thu, May 11, 2006 at 04:44:03PM -0700, Linus Torvalds wrote:
> > > Ok, I've let the release time between -rc's slide a bit too much again,
> > > but -rc4 is out there, and this is the time to hunker down for 2.6.17.
> > >
> > > If you know of any regressions, please holler now, so that we don't miss
> > > them.
> >
> > I got assertion failures in the bcm43xx driver:
> >
> > bcm43xx: Chip ID 0x4318, rev 0x2
>
> That is expected an non-fatal.
Is this one in the same category?
[ 79.087115] bcm43xx: WARNING: Writing invalid LOpair (low: 46, high: 104, index: 123)
[ 0.000000] Using PowerMac machine description
[ 0.000000] Total memory = 768MB; using 2048kB for hash table (at cfe00000)
[ 0.000000] Linux version 2.6.17-rc4-airport (olaf@pomegranate) (gcc version 4.1.0 (SUSE Linux)) #3 Fri May 12 13:12:42 CEST 2006
[ 0.000000] Found initrd at 0xc4100000:0xc445d000
[ 0.000000] Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0xd2
[ 0.000000] Mapped at 0xfdfc0000
[ 0.000000] Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdf40000
[ 0.000000] Processor NAP mode on idle enabled.
[ 0.000000] PowerMac motherboard: iBook G4
[ 0.000000] via-pmu: Server Mode is disabled
[ 0.000000] PMU driver v2 initialized for Core99, firmware: 0c
[ 0.000000] Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0
[ 0.000000] Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0
[ 0.000000] Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0
[ 0.000000] Top of RAM: 0x30000000, Total RAM: 0x30000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] On node 0 totalpages: 196608
[ 0.000000] DMA zone: 196608 pages, LIFO batch:31
[ 0.000000] Built 1 zonelists
[ 0.000000] Kernel command line: root=/dev/hda2 quiet time sysrq=1
[ 0.000000] mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs
[ 0.000000] mpic: ISU size: 64, shift: 6, mask: 3f
[ 0.000000] mpic: Initializing for 64 sources
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] time_init: decrementer frequency = 18.432000 MHz
[ 0.000000] time_init: processor frequency = 1333.333330 MHz
[ 23.809911] Console: colour dummy device 80x25
[ 23.810822] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 23.812165] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 23.854228] Memory: 767232k/786432k available (3160k kernel code, 18664k reserved, 448k data, 2177k bss, 160k init)
[ 23.854480] Calibrating delay loop... 36.76 BogoMIPS (lpj=183808)
[ 24.039729] Mount-cache hash table entries: 512
[ 24.040130] device-tree: Duplicate name in /cpus/PowerPC,G4@0, renamed to "l2-cache#1"
[ 24.043262] checking if image is initramfs... it is
[ 24.734182] Freeing initrd memory: 3444k freed
[ 24.735401] NET: Registered protocol family 16
[ 24.736061] KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000
[ 24.736074] channel 1 bus /uni-n@f8000000/i2c@f8001000/i2c-bus@1
[ 24.736123] KeyWest i2c @0x80018000 irq 26 /pci@f2000000/mac-io@17/i2c@18000
[ 24.736134] channel 0 bus /pci@f2000000/mac-io@17/i2c@18000/i2c-bus@0
[ 24.736161] PMU i2c /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c
[ 24.736169] channel 1 bus <multibus>
[ 24.736176] channel 2 bus <multibus>
[ 24.736706] PCI: Probing PCI hardware
[ 24.739527] PCI: Cannot allocate resource region 0 of device 0001:10:18.0
[ 24.739549] PCI: Cannot allocate resource region 0 of device 0001:10:19.0
[ 24.739583] Apple USB OHCI 0001:10:18.0 disabled by firmware
[ 24.739596] Apple USB OHCI 0001:10:19.0 disabled by firmware
[ 24.740556] usbcore: registered new driver usbfs
[ 24.740655] usbcore: registered new driver hub
[ 24.740917] TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
[ 24.741608] NET: Registered protocol family 2
[ 24.829781] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 24.830282] TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
[ 24.839978] TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
[ 24.846243] TCP: Hash tables configured (established 131072 bind 65536)
[ 24.846253] TCP reno registered
[ 24.846361] Thermal assist unit not available
[ 24.848508] VFS: Disk quotas dquot_6.5.1
[ 24.848561] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 24.848760] Initializing Cryptographic API
[ 24.848777] io scheduler noop registered
[ 24.848792] io scheduler anticipatory registered
[ 24.848806] io scheduler deadline registered
[ 24.848833] io scheduler cfq registered (default)
[ 24.849393] PCI: Enabling device 0000:00:10.0 (0006 -> 0007)
[ 25.045487] radeonfb (0000:00:10.0): Invalid ROM signature 0 should be 0xaa55
[ 25.045502] radeonfb: Retrieved PLL infos from Open Firmware
[ 25.045513] radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=183.00 Mhz, System=210.00 MHz
[ 25.045522] radeonfb: PLL min 12000 max 35000
[ 26.090640] radeonfb: Monitor 1 type LCD found
[ 26.090648] radeonfb: EDID probed
[ 26.090654] radeonfb: Monitor 2 type no found
[ 26.090672] radeonfb: Using Firmware dividers 0x00020074 from PPLL 0
[ 26.090750] radeonfb: Dynamic Clock Power Management enabled
[ 26.143184] Console: switching to colour frame buffer device 128x48
[ 26.143276] Registered "mnca" backlight controller,level: 15/15
[ 26.143283] radeonfb (0000:00:10.0): ATI Radeon NV
[ 26.148372] Generic RTC Driver v1.07
[ 26.150099] RAMDISK driver initialized: 16 RAM disks of 123456K size 1024 blocksize
[ 26.150201] sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
[ 26.230004] PHY ID: 4061e4, addr: 0
[ 26.230765] eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:11:24:e3:f0:1e
[ 26.230785] eth0: Found BCM5221 PHY
[ 26.231143] MacIO PCI driver attached to Intrepid chipset
[ 26.232921] input: Macintosh mouse button emulation as /class/input/input0
[ 26.233164] apm_emu: APM Emulation 0.5 initialized.
[ 26.233299] adt746x: version 1 (supported)
[ 26.233311] adt746x: Thermostat bus: 1, address: 0x2e, limit_adjust: 0, fan_speed: -1
[ 26.233322] sensor 0: PWR/MEMORY BOTTOMSIDE
[ 26.233330] sensor 1: CPU BOTTOMSIDE
[ 26.233336] sensor 2: GPU BOTTOMSIDE
[ 26.233404] adb: starting probe task...
[ 26.234766] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 26.234779] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 26.234975] PCI: Enabling device 0002:20:0d.0 (0000 -> 0002)
[ 26.259143] adb devices: [2]: 2 c4 [7]: 7 1f
[ 26.264488] ADB keyboard at 2, handler 1
[ 26.264503] Detected ADB keyboard, type ISO, swapping keys.
[ 26.264666] input: ADB keyboard as /class/input/input1
[ 26.264820] input: ADB Powerbook buttons as /class/input/input2
[ 26.264833] adb: finished probe task...
[ 27.259660] ide0: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39
[ 27.259682] Probing IDE interface ide0...
[ 27.559841] hda: FUJITSU MHV2060AT, ATA DISK drive
[ 28.279667] hda: Enabling Ultra DMA 5
[ 28.283665] ide0 at 0xf1012000-0xf1012007,0xf1012160 on irq 39
[ 28.629816] eth0: Link is up at 100 Mbps, full-duplex.
[ 29.309658] ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24
[ 29.309676] Probing IDE interface ide1...
[ 29.729843] hdc: MATSHITACD-RW CW-8124, ATAPI CD/DVD-ROM drive
[ 30.089675] hdc: Enabling MultiWord DMA 2
[ 30.090716] ide1 at 0xf1006000-0xf1006007,0xf1006160 on irq 24
[ 30.091002] hda: max request size: 512KiB
[ 30.162948] hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
[ 30.167677] hda: cache flushes supported
[ 30.167772] hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8
[ 30.175449] PCI: Enabling device 0001:10:1b.2 (0004 -> 0006)
[ 30.175471] ehci_hcd 0001:10:1b.2: EHCI Host Controller
[ 30.175627] ehci_hcd 0001:10:1b.2: new USB bus registered, assigned bus number 1
[ 30.199693] ehci_hcd 0001:10:1b.2: irq 63, io mem 0x80080000
[ 30.199707] ehci_hcd 0001:10:1b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 30.199952] usb usb1: configuration #1 chosen from 1 choice
[ 30.200063] hub 1-0:1.0: USB hub found
[ 30.200094] hub 1-0:1.0: 5 ports detected
[ 30.309822] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[ 30.309942] Apple USB OHCI 0001:10:18.0 disabled by firmware
[ 30.309959] Apple USB OHCI 0001:10:19.0 disabled by firmware
[ 30.309976] PCI: Enabling device 0001:10:1a.0 (0000 -> 0002)
[ 30.309997] ohci_hcd 0001:10:1a.0: OHCI Host Controller
[ 30.310125] ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 2
[ 30.310158] ohci_hcd 0001:10:1a.0: irq 29, io mem 0x80083000
[ 30.389370] usb usb2: configuration #1 chosen from 1 choice
[ 30.389471] hub 2-0:1.0: USB hub found
[ 30.389495] hub 2-0:1.0: 2 ports detected
[ 30.489827] PCI: Enabling device 0001:10:1b.0 (0000 -> 0002)
[ 30.489846] ohci_hcd 0001:10:1b.0: OHCI Host Controller
[ 30.489981] ohci_hcd 0001:10:1b.0: new USB bus registered, assigned bus number 3
[ 30.490009] ohci_hcd 0001:10:1b.0: irq 63, io mem 0x80082000
[ 30.569361] usb usb3: configuration #1 chosen from 1 choice
[ 30.569461] hub 3-0:1.0: USB hub found
[ 30.569483] hub 3-0:1.0: 3 ports detected
[ 30.669823] PCI: Enabling device 0001:10:1b.1 (0000 -> 0002)
[ 30.669841] ohci_hcd 0001:10:1b.1: OHCI Host Controller
[ 30.669940] ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 4
[ 30.669966] ohci_hcd 0001:10:1b.1: irq 63, io mem 0x80081000
[ 30.749372] usb usb4: configuration #1 chosen from 1 choice
[ 30.749469] hub 4-0:1.0: USB hub found
[ 30.749492] hub 4-0:1.0: 2 ports detected
[ 30.789662] usb 2-1: new full speed USB device using ohci_hcd and address 2
[ 31.004679] usb 2-1: configuration #1 chosen from 1 choice
[ 31.299660] usb 2-2: new full speed USB device using ohci_hcd and address 3
[ 31.488678] usb 2-2: configuration #1 chosen from 1 choice
[ 31.492824] usbcore: registered new driver hiddev
[ 31.524884] input: HID 05ac:1000 as /class/input/input3
[ 31.524917] input: USB HID v1.11 Keyboard [HID 05ac:1000] on usb-0001:10:1a.0-1
[ 31.565847] input: HID 05ac:1000 as /class/input/input4
[ 31.565861] input: USB HID v1.11 Mouse [HID 05ac:1000] on usb-0001:10:1a.0-1
[ 31.572679] HID device not claimed by input or hiddev
[ 31.572711] usbcore: registered new driver usbhid
[ 31.572720] /home/olaf/kernel/olh/airport/linux-2.6.17-rc4/drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 31.572966] mice: PS/2 mouse device common for all mice
[ 31.573542] PowerMac i2c bus pmu 2 registered
[ 31.573649] PowerMac i2c bus pmu 1 registered
[ 31.573781] PowerMac i2c bus mac-io 0 registered
[ 31.574329] adt746x: ADT7467 initializing
[ 31.576521] adt746x: Lowering max temperatures from 69, 92, 101 to 70, 50, 70
[ 31.577694] PowerMac i2c bus uni-n 1 registered
[ 31.577715] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 31.577723] md: bitmap version 4.39
[ 31.577931] NET: Registered protocol family 1
[ 31.577948] NET: Registered protocol family 17
[ 31.577963] NET: Registered protocol family 15
[ 31.578044] Freeing unused kernel memory: 160k init
[ 35.655774] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 36.937288] ReiserFS: hda2: using ordered data mode
[ 36.937791] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 36.940521] ReiserFS: hda2: checking transaction log (hda2)
[ 37.033930] ReiserFS: hda2: Using r5 hash to sort names
[ 38.939608] Adding 530136k swap on /dev/hda6. Priority:-1 extents:1 across:530136k
[ 42.013907] input: PowerMac Beep as /class/input/input5
[ 43.484073] input: appletouch as /class/input/input6
[ 43.484182] usbcore: registered new driver appletouch
[ 45.043454] Linux agpgart interface v0.101 (c) Dave Jones
[ 45.186632] hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, (U)DMA
[ 45.186659] Uniform CD-ROM driver Revision: 3.20
[ 45.191243] agpgart: Detected Apple UniNorth 2 chipset
[ 45.191366] agpgart: configuring for size idx: 4
[ 45.191431] agpgart: AGP aperture is 16M @ 0x0
[ 45.666918] ieee1394: Initialized config rom entry `ip1394'
[ 45.694136] ieee80211_crypt: registered algorithm 'NULL'
[ 46.148147] PCI: Enabling device 0002:20:0e.0 (0000 -> 0002)
[ 46.219702] ieee80211: 802.11 data/management/control stack, git-1.1.7
[ 46.219716] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 46.241574] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048] IR/IT contexts=[8/8]
[ 47.354898] bcm43xx driver
[ 47.355496] PCI: Enabling device 0001:10:12.0 (0004 -> 0006)
[ 47.361435] bcm43xx: Chip ID 0x4318, rev 0x2
[ 47.361442] bcm43xx: Number of cores: 4
[ 47.361452] bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243, enabled
[ 47.361467] bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243, disabled
[ 47.361482] bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243, enabled
[ 47.361497] bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243, enabled
[ 47.364759] bcm43xx: PHY connected
[ 47.364778] bcm43xx: Detected PHY: Version: 3, Type 2, Revision 7
[ 47.364806] bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev: 8)
[ 47.364835] bcm43xx: Radio turned off
[ 47.364857] bcm43xx: Radio turned off
[ 47.728792] ieee1394: Host added: ID:BUS[0-00:1023] GUID[001124fffee3f01e]
[ 48.944822] device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
[ 50.220481] loop: loaded (max 8 devices)
[ 50.240129] kjournald starting. Commit interval 5 seconds
[ 50.259939] EXT3 FS on hda5, internal journal
[ 50.259957] EXT3-fs: mounted filesystem with ordered data mode.
[ 55.277144] NET: Registered protocol family 10
[ 55.283176] lo: Disabled Privacy Extensions
[ 55.289024] IPv6 over IPv4 tunneling driver
[ 55.543587] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 56.192479] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 56.314463] Netfilter messages via NETLINK v0.30.
[ 56.638288] ip_conntrack version 2.4 (6144 buckets, 49152 max) - 208 bytes per conntrack
[ 71.626052] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 72.532956] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 72.537269] NFSD: starting 90-second grace period
[ 77.766307] bcm43xx: PHY connected
[ 79.071344] bcm43xx: Radio turned on
[ 79.087099] bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: /home/olaf/kernel/olh/airport/linux-2.6.17-rc4/drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
[ 79.087115] bcm43xx: WARNING: Writing invalid LOpair (low: 46, high: 104, index: 123)
[ 79.087123] Call Trace:
[ 79.087129] [EC571960] [C0007D98] show_stack+0x50/0x184 (unreliable)
[ 79.087155] [EC571980] [F24F12B8] bcm43xx_phy_lo_adjust+0x2e8/0x30c [bcm43xx]
[ 79.087231] [EC5719A0] [F24ECFAC] bcm43xx_radio_set_txpower_bg+0x284/0x298 [bcm43xx]
[ 79.087260] [EC5719C0] [F24F0AC0] bcm43xx_phy_initb6+0x758/0x8b4 [bcm43xx]
[ 79.087289] [EC5719E0] [F24F1F28] bcm43xx_phy_initg+0x130/0xe54 [bcm43xx]
[ 79.087317] [EC571A50] [F24F4344] bcm43xx_phy_init+0x6f8/0x730 [bcm43xx]
[ 79.087346] [EC571A70] [F24E3140] bcm43xx_wireless_core_init+0x8a0/0x10b4 [bcm43xx]
[ 79.087375] [EC571B00] [F24E52E0] bcm43xx_init_board+0x2f8/0x624 [bcm43xx]
[ 79.087402] [EC571B30] [C020D9E4] dev_open+0x60/0xc8
[ 79.087423] [EC571B50] [C020B910] dev_change_flags+0x70/0x148
[ 79.087438] [EC571B70] [C0216DD0] do_setlink+0x78/0x390
[ 79.087453] [EC571BB0] [C0216944] rtnetlink_rcv_msg+0x204/0x230
[ 79.087466] [EC571BE0] [C0222C68] netlink_run_queue+0x80/0x188
[ 79.087481] [EC571C20] [C02166B8] rtnetlink_rcv+0x40/0x6c
[ 79.087494] [EC571C50] [C0223284] netlink_data_ready+0x28/0x84
[ 79.087507] [EC571C60] [C0221C2C] netlink_sendskb+0x34/0x70
[ 79.087520] [EC571C80] [C0223240] netlink_sendmsg+0x260/0x27c
[ 79.087533] [EC571CD0] [C0200B00] sock_sendmsg+0xac/0xdc
[ 79.087552] [EC571DC0] [C020182C] sys_sendmsg+0x1c8/0x254
[ 79.087567] [EC571F00] [C02029A4] sys_socketcall+0x1ac/0x1e4
[ 79.087582] [EC571F40] [C000F300] ret_from_syscall+0x0/0x38
[ 79.087598] --- Exception: c01 at 0xff05d48
[ 79.087619] LR = 0xff66798
[ 79.240869] bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: /home/olaf/kernel/olh/airport/linux-2.6.17-rc4/drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
[ 79.240884] bcm43xx: WARNING: Writing invalid LOpair (low: 46, high: 104, index: 123)
[ 79.240892] Call Trace:
[ 79.240898] [EC5719A0] [C0007D98] show_stack+0x50/0x184 (unreliable)
[ 79.240913] [EC5719C0] [F24F12B8] bcm43xx_phy_lo_adjust+0x2e8/0x30c [bcm43xx]
[ 79.240943] [EC5719E0] [F24F2AE8] bcm43xx_phy_initg+0xcf0/0xe54 [bcm43xx]
[ 79.240971] [EC571A50] [F24F4344] bcm43xx_phy_init+0x6f8/0x730 [bcm43xx]
[ 79.240999] [EC571A70] [F24E3140] bcm43xx_wireless_core_init+0x8a0/0x10b4 [bcm43xx]
[ 79.241028] [EC571B00] [F24E52E0] bcm43xx_init_board+0x2f8/0x624 [bcm43xx]
[ 79.241055] [EC571B30] [C020D9E4] dev_open+0x60/0xc8
[ 79.241069] [EC571B50] [C020B910] dev_change_flags+0x70/0x148
[ 79.241083] [EC571B70] [C0216DD0] do_setlink+0x78/0x390
[ 79.241095] [EC571BB0] [C0216944] rtnetlink_rcv_msg+0x204/0x230
[ 79.241108] [EC571BE0] [C0222C68] netlink_run_queue+0x80/0x188
[ 79.241121] [EC571C20] [C02166B8] rtnetlink_rcv+0x40/0x6c
[ 79.241133] [EC571C50] [C0223284] netlink_data_ready+0x28/0x84
[ 79.241146] [EC571C60] [C0221C2C] netlink_sendskb+0x34/0x70
[ 79.241158] [EC571C80] [C0223240] netlink_sendmsg+0x260/0x27c
[ 79.241171] [EC571CD0] [C0200B00] sock_sendmsg+0xac/0xdc
[ 79.241186] [EC571DC0] [C020182C] sys_sendmsg+0x1c8/0x254
[ 79.241199] [EC571F00] [C02029A4] sys_socketcall+0x1ac/0x1e4
[ 79.241214] [EC571F40] [C000F300] ret_from_syscall+0x0/0x38
[ 79.241226] --- Exception: c01 at 0xff05d48
[ 79.241239] LR = 0xff66798
[ 79.242938] bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: /home/olaf/kernel/olh/airport/linux-2.6.17-rc4/drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
[ 79.242953] bcm43xx: WARNING: Writing invalid LOpair (low: 46, high: 104, index: 123)
[ 79.242960] Call Trace:
[ 79.242966] [EC571960] [C0007D98] show_stack+0x50/0x184 (unreliable)
[ 79.242981] [EC571980] [F24F12B8] bcm43xx_phy_lo_adjust+0x2e8/0x30c [bcm43xx]
[ 79.243010] [EC5719A0] [F24ECFAC] bcm43xx_radio_set_txpower_bg+0x284/0x298 [bcm43xx]
[ 79.243039] [EC5719C0] [F24EFC40] bcm43xx_phy_init_pctl+0x284/0x2a0 [bcm43xx]
[ 79.243068] [EC5719E0] [F24F2BD8] bcm43xx_phy_initg+0xde0/0xe54 [bcm43xx]
[ 79.243096] [EC571A50] [F24F4344] bcm43xx_phy_init+0x6f8/0x730 [bcm43xx]
[ 79.243124] [EC571A70] [F24E3140] bcm43xx_wireless_core_init+0x8a0/0x10b4 [bcm43xx]
[ 79.243153] [EC571B00] [F24E52E0] bcm43xx_init_board+0x2f8/0x624 [bcm43xx]
[ 79.243180] [EC571B30] [C020D9E4] dev_open+0x60/0xc8
[ 79.243193] [EC571B50] [C020B910] dev_change_flags+0x70/0x148
[ 79.243207] [EC571B70] [C0216DD0] do_setlink+0x78/0x390
[ 79.243220] [EC571BB0] [C0216944] rtnetlink_rcv_msg+0x204/0x230
[ 79.243232] [EC571BE0] [C0222C68] netlink_run_queue+0x80/0x188
[ 79.243246] [EC571C20] [C02166B8] rtnetlink_rcv+0x40/0x6c
[ 79.243258] [EC571C50] [C0223284] netlink_data_ready+0x28/0x84
[ 79.243271] [EC571C60] [C0221C2C] netlink_sendskb+0x34/0x70
[ 79.243283] [EC571C80] [C0223240] netlink_sendmsg+0x260/0x27c
[ 79.243296] [EC571CD0] [C0200B00] sock_sendmsg+0xac/0xdc
[ 79.243310] [EC571DC0] [C020182C] sys_sendmsg+0x1c8/0x254
[ 79.243324] [EC571F00] [C02029A4] sys_socketcall+0x1ac/0x1e4
[ 79.243338] [EC571F40] [C000F300] ret_from_syscall+0x0/0x38
[ 79.243350] --- Exception: c01 at 0xff05d48
[ 79.243361] LR = 0xff66798
[ 79.243921] bcm43xx: Chip initialized
[ 79.249384] bcm43xx: DMA initialized
[ 79.249408] bcm43xx: 80211 cores initialized
[ 79.249627] bcm43xx: Keys cleared
[ 79.257753] bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: /home/olaf/kernel/olh/airport/linux-2.6.17-rc4/drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
[ 79.257769] bcm43xx: WARNING: Writing invalid LOpair (low: 46, high: 104, index: 123)
[ 79.257778] Call Trace:
[ 79.257784] [EC571810] [C0007D98] show_stack+0x50/0x184 (unreliable)
[ 79.257808] [EC571830] [F24F12B8] bcm43xx_phy_lo_adjust+0x2e8/0x30c [bcm43xx]
[ 79.257875] [EC571850] [F24F1A64] bcm43xx_phy_lo_g_measure+0x788/0xb1c [bcm43xx]
[ 79.257904] [EC5718D0] [F24E2234] bcm43xx_periodic_task_handler+0x104/0x344 [bcm43xx]
[ 79.257932] [EC5718F0] [C0035284] run_timer_softirq+0x144/0x1bc
[ 79.257953] [EC571920] [C0030978] __do_softirq+0x64/0xe4
[ 79.257966] [EC571940] [C0005A94] do_softirq+0x50/0x74
[ 79.257979] [EC571950] [C0030904] irq_exit+0x38/0x48
[ 79.257992] [EC571960] [C000C120] timer_interrupt+0x508/0x51c
[ 79.258007] [EC5719C0] [C000F9A8] ret_from_except+0x0/0x14
[ 79.258022] --- Exception: 901 at mutex_lock+0x2c/0x6c
[ 79.258036] LR = mutex_lock+0x28/0x6c
[ 79.258043] [EC571AA0] [C00B6B08] sysfs_add_file+0x34/0x8c
[ 79.258061] [EC571AC0] [C019C51C] device_create_file+0x34/0x58
[ 79.258081] [EC571AE0] [F24F7D54] bcm43xx_sysfs_register+0x60/0xcc [bcm43xx]
[ 79.258115] [EC571B00] [F24E5578] bcm43xx_init_board+0x590/0x624 [bcm43xx]
[ 79.258143] [EC571B30] [C020D9E4] dev_open+0x60/0xc8
[ 79.258162] [EC571B50] [C020B910] dev_change_flags+0x70/0x148
[ 79.258176] [EC571B70] [C0216DD0] do_setlink+0x78/0x390
[ 79.258189] [EC571BB0] [C0216944] rtnetlink_rcv_msg+0x204/0x230
[ 79.258203] [EC571BE0] [C0222C68] netlink_run_queue+0x80/0x188
[ 79.258218] [EC571C20] [C02166B8] rtnetlink_rcv+0x40/0x6c
[ 79.258230] [EC571C50] [C0223284] netlink_data_ready+0x28/0x84
[ 79.258243] [EC571C60] [C0221C2C] netlink_sendskb+0x34/0x70
[ 79.258256] [EC571C80] [C0223240] netlink_sendmsg+0x260/0x27c
[ 79.258269] [EC571CD0] [C0200B00] sock_sendmsg+0xac/0xdc
[ 79.258288] [EC571DC0] [C020182C] sys_sendmsg+0x1c8/0x254
[ 79.258302] [EC571F00] [C02029A4] sys_socketcall+0x1ac/0x1e4
[ 79.258317] [EC571F40] [C000F300] ret_from_syscall+0x0/0x38
[ 79.258329] --- Exception: c01 at 0xff05d48
[ 79.258349] LR = 0xff66798
[ 79.268404] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 79.525350] SoftMAC: Start scanning with channel: 1
[ 79.525362] SoftMAC: Scanning 14 channels
[ 79.839760] SoftMAC: Scanning finished
[ 82.000532] SoftMAC: Associate: Scanning for networks first.
[ 82.000551] SoftMAC: Start scanning with channel: 1
[ 82.000558] SoftMAC: Scanning 14 channels
[ 82.279679] SoftMAC: Scanning finished
[ 82.279727] SoftMAC: Associate: Scanning for networks first.
[ 82.279740] SoftMAC: Start scanning with channel: 1
[ 82.279747] SoftMAC: Scanning 14 channels
[ 82.559728] SoftMAC: Scanning finished
[ 82.559783] SoftMAC: Associate: Scanning for networks first.
[ 82.559798] SoftMAC: Start scanning with channel: 1
[ 82.559805] SoftMAC: Scanning 14 channels
[ 82.849676] SoftMAC: Scanning finished
[ 82.849730] SoftMAC: Unable to find matching network after scan!
[ 84.009832] bcm43xx: set security called
[ 84.009844] bcm43xx: .level = 0
[ 84.009850] bcm43xx: .enabled = 0
[ 84.009856] bcm43xx: .encrypt = 0
[ 84.045918] eth0: Link is up at 100 Mbps, full-duplex.
[ 84.045931] eth0: Pause is disabled
[ 96.400807] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:13:77:04:15:b7:08:00 SRC=10.10.103.184 DST=224.0.0.251 LEN=72 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=52
[ 96.559913] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.10.100.46 DST=224.0.0.251 LEN=76 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=56
[ 96.652764] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:13:77:04:15:b7:08:00 SRC=10.10.103.184 DST=224.0.0.251 LEN=72 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=52
[ 96.819857] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.10.100.46 DST=224.0.0.251 LEN=76 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=56
[ 96.904775] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:13:77:04:15:b7:08:00 SRC=10.10.103.184 DST=224.0.0.251 LEN=72 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=52
[ 97.069829] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.10.100.46 DST=224.0.0.251 LEN=76 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=56
[ 97.319893] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.10.100.46 DST=224.0.0.251 LEN=109 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=89
[ 98.319959] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.10.100.46 DST=224.0.0.251 LEN=109 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=89
[ 99.909871] SoftMAC: Start scanning with channel: 1
[ 99.909885] SoftMAC: Scanning 14 channels
[ 100.189696] SoftMAC: Scanning finished
[ 105.864700] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:02:3f:14:43:68:08:00 SRC=10.10.1.91 DST=224.0.0.251 LEN=105 TOS=0x00 PREC=0x00 TTL=255 ID=4 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
[ 106.484935] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:13:77:04:15:b7:08:00 SRC=10.10.103.184 DST=224.0.0.251 LEN=72 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=52
[ 106.736931] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:13:77:04:15:b7:08:00 SRC=10.10.103.184 DST=224.0.0.251 LEN=72 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=52
[ 106.988938] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:13:77:04:15:b7:08:00 SRC=10.10.103.184 DST=224.0.0.251 LEN=72 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=52
[ 107.240956] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:13:77:04:15:b7:08:00 SRC=10.10.103.184 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=86
[ 108.230064] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.10.100.46 DST=224.0.0.251 LEN=109 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=89
[ 116.232421] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.10.100.46 DST=224.0.0.251 LEN=109 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=89
[ 120.289923] SoftMAC: Start scanning with channel: 1
[ 120.289939] SoftMAC: Scanning 14 channels
[ 120.569731] SoftMAC: Scanning finished
[ 121.000248] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.10.100.46 DST=224.0.0.251 LEN=76 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=56
[ 121.259856] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.10.100.46 DST=224.0.0.251 LEN=76 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=56
[ 121.519876] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.10.100.46 DST=224.0.0.251 LEN=76 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=56
[ 126.067233] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:02:3f:14:43:68:08:00 SRC=10.10.1.91 DST=224.0.0.251 LEN=105 TOS=0x00 PREC=0x00 TTL=255 ID=4 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
[ 128.780029] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.10.100.46 DST=224.0.0.251 LEN=109 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=89
[ 140.669817] SoftMAC: Start scanning with channel: 1
[ 140.669832] SoftMAC: Scanning 14 channels
[ 140.949681] SoftMAC: Scanning finished
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Linux v2.6.17-rc4
2006-05-12 10:44 ` Michael Buesch
2006-05-12 11:23 ` Olaf Hering
@ 2006-05-12 11:47 ` Erik Mouw
2006-05-12 20:58 ` Michael Buesch
1 sibling, 1 reply; 10+ messages in thread
From: Erik Mouw @ 2006-05-12 11:47 UTC (permalink / raw)
To: Michael Buesch; +Cc: Linux Kernel Mailing List, netdev, Linus Torvalds
On Fri, May 12, 2006 at 12:44:22PM +0200, Michael Buesch wrote:
> On Friday 12 May 2006 12:24, you wrote:
> > On Thu, May 11, 2006 at 04:44:03PM -0700, Linus Torvalds wrote:
> > > Ok, I've let the release time between -rc's slide a bit too much again,
> > > but -rc4 is out there, and this is the time to hunker down for 2.6.17.
> > >
> > > If you know of any regressions, please holler now, so that we don't miss
> > > them.
> >
> > I got assertion failures in the bcm43xx driver:
> >
> > bcm43xx: Chip ID 0x4318, rev 0x2
>
> That is expected an non-fatal.
Assertion failed sounds rather fatal to me.
> It is no regression.
It is, I didn't see it in 2.6.17-rc3.
> We are working on it, but there won't be any fix for 2.6.17, as
> very intrusive changes are needed to fix this.
If it's non-fatal, could you remove the assertion, or make it print
something that sounds less fatal?
Erik
--
+-- Erik Mouw -- www.harddisk-recovery.com -- +31 70 370 12 90 --
| Lab address: Delftechpark 26, 2628 XH, Delft, The Netherlands
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Linux v2.6.17-rc4
2006-05-12 11:23 ` Olaf Hering
@ 2006-05-12 20:54 ` Michael Buesch
0 siblings, 0 replies; 10+ messages in thread
From: Michael Buesch @ 2006-05-12 20:54 UTC (permalink / raw)
To: Olaf Hering; +Cc: Erik Mouw, netdev
On Friday 12 May 2006 13:23, you wrote:
> > > I got assertion failures in the bcm43xx driver:
> > >
> > > bcm43xx: Chip ID 0x4318, rev 0x2
> >
> > That is expected an non-fatal.
>
> Is this one in the same category?
> [ 79.087115] bcm43xx: WARNING: Writing invalid LOpair (low: 46, high: 104, index: 123)
> [ 47.361435] bcm43xx: Chip ID 0x4318, rev 0x2
^^^^^^
Yes, same problem.
--
Greetings Michael.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Linux v2.6.17-rc4
2006-05-12 11:47 ` Erik Mouw
@ 2006-05-12 20:58 ` Michael Buesch
0 siblings, 0 replies; 10+ messages in thread
From: Michael Buesch @ 2006-05-12 20:58 UTC (permalink / raw)
To: Erik Mouw; +Cc: Linux Kernel Mailing List, netdev, Linus Torvalds
On Friday 12 May 2006 13:47, you wrote:
> On Fri, May 12, 2006 at 12:44:22PM +0200, Michael Buesch wrote:
> > On Friday 12 May 2006 12:24, you wrote:
> > > On Thu, May 11, 2006 at 04:44:03PM -0700, Linus Torvalds wrote:
> > > > Ok, I've let the release time between -rc's slide a bit too much again,
> > > > but -rc4 is out there, and this is the time to hunker down for 2.6.17.
> > > >
> > > > If you know of any regressions, please holler now, so that we don't miss
> > > > them.
> > >
> > > I got assertion failures in the bcm43xx driver:
> > >
> > > bcm43xx: Chip ID 0x4318, rev 0x2
> >
> > That is expected an non-fatal.
>
> Assertion failed sounds rather fatal to me.
But it is not fatal. Trust me. I am the author of most of the code.
The worst thing that can happen is that the card does not work.
The best thing that can happen is that it works with some luck.
> > It is no regression.
>
> It is, I didn't see it in 2.6.17-rc3.
You did not look close enough.
> > We are working on it, but there won't be any fix for 2.6.17, as
> > very intrusive changes are needed to fix this.
>
> If it's non-fatal, could you remove the assertion, or make it print
> something that sounds less fatal?
Well, the backtrace could be removed.
But I am for not removing the assertions completely, because
this way people don't see what is going on, if the device does not
work.
It is non-fatal in the sense that it does not crash the machine.
It _may_ be fatal, that the device does not work. The
driver is CONFIG_EXPERIMENTAL for some reason.
To say it again: The 4318 is not completely supported, yet.
It may work with some luck, but it is not guaranteed and only
lower bitrates are supported.
--
Greetings Michael.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Linux v2.6.17-rc4
[not found] <Pine.LNX.4.64.0605111640010.3866@g5.osdl.org>
2006-05-12 10:24 ` Linux v2.6.17-rc4 Erik Mouw
@ 2006-05-12 21:19 ` Alistair John Strachan
2006-05-14 7:57 ` Ayaz Abdulla
1 sibling, 1 reply; 10+ messages in thread
From: Alistair John Strachan @ 2006-05-12 21:19 UTC (permalink / raw)
To: Linus Torvalds; +Cc: Linux Kernel Mailing List, aabdulla, jeff, netdev
On Friday 12 May 2006 00:44, Linus Torvalds wrote:
> Ok, I've let the release time between -rc's slide a bit too much again,
> but -rc4 is out there, and this is the time to hunker down for 2.6.17.
>
> If you know of any regressions, please holler now, so that we don't miss
> them.
>
> -rc4 itself is mainly random driver fixes (sound, infiniband, scsi,
> network drivers), but some splice fixes too and some arch (arm, powerpc,
> mips) updates. Shortlog follows,
Linus,
I've got an oops in the forcedeth driver on shutdown. Sorry for the crappy
camera phone pictures, this board doesn't have RS232 ports:
http://devzero.co.uk/~alistair/oops-20060512/
It was initially difficult to reproduce, but I found I could do so reliably if
I ssh'ed into the box and halted it remotely, then it would always oops on
shutdown. I assume this is because the driver is still active when something
happens to it during halt.
There's been just a single commit since -rc3:
forcedeth: fix multi irq issues
ebf34c9b6fcd22338ef764b039b3ac55ed0e297b
However, it could have just been hidden since before -rc3, so I'll try to work
backwards if nobody has any immediate ideas..
--
Cheers,
Alistair.
Third year Computer Science undergraduate.
1F2 55 South Clerk Street, Edinburgh, UK.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Linux v2.6.17-rc4
2006-05-12 21:19 ` Alistair John Strachan
@ 2006-05-14 7:57 ` Ayaz Abdulla
2006-05-15 5:27 ` Alistair John Strachan
0 siblings, 1 reply; 10+ messages in thread
From: Ayaz Abdulla @ 2006-05-14 7:57 UTC (permalink / raw)
To: Alistair John Strachan
Cc: Linus Torvalds, Linux Kernel Mailing List, jeff, netdev,
Manfred Spraul
Alistair John Strachan wrote:
> On Friday 12 May 2006 00:44, Linus Torvalds wrote:
>
>>Ok, I've let the release time between -rc's slide a bit too much again,
>>but -rc4 is out there, and this is the time to hunker down for 2.6.17.
>>
>>If you know of any regressions, please holler now, so that we don't miss
>>them.
>>
>>-rc4 itself is mainly random driver fixes (sound, infiniband, scsi,
>>network drivers), but some splice fixes too and some arch (arm, powerpc,
>>mips) updates. Shortlog follows,
>
>
> Linus,
>
> I've got an oops in the forcedeth driver on shutdown. Sorry for the crappy
> camera phone pictures, this board doesn't have RS232 ports:
>
> http://devzero.co.uk/~alistair/oops-20060512/
>
> It was initially difficult to reproduce, but I found I could do so reliably if
> I ssh'ed into the box and halted it remotely, then it would always oops on
> shutdown. I assume this is because the driver is still active when something
> happens to it during halt.
>
> There's been just a single commit since -rc3:
>
> forcedeth: fix multi irq issues
> ebf34c9b6fcd22338ef764b039b3ac55ed0e297b
>
> However, it could have just been hidden since before -rc3, so I'll try to work
> backwards if nobody has any immediate ideas..
>
The interrupt handler could be called during the same time (on different
cpu) the dev->stop function is clearing out the rings (nv_txrx_reset).
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Linux v2.6.17-rc4
2006-05-14 7:57 ` Ayaz Abdulla
@ 2006-05-15 5:27 ` Alistair John Strachan
2006-05-20 19:11 ` Alistair John Strachan
0 siblings, 1 reply; 10+ messages in thread
From: Alistair John Strachan @ 2006-05-15 5:27 UTC (permalink / raw)
To: Ayaz Abdulla
Cc: Linus Torvalds, Linux Kernel Mailing List, jeff, netdev,
Manfred Spraul
On Sunday 14 May 2006 08:57, Ayaz Abdulla wrote:
> Alistair John Strachan wrote:
[snip]
> > There's been just a single commit since -rc3:
> >
> > forcedeth: fix multi irq issues
> > ebf34c9b6fcd22338ef764b039b3ac55ed0e297b
> >
> > However, it could have just been hidden since before -rc3, so I'll try to
> > work backwards if nobody has any immediate ideas..
>
> The interrupt handler could be called during the same time (on different
> cpu) the dev->stop function is clearing out the rings (nv_txrx_reset).
FWIW, I can't reproduce the fault with the commitdiff
ebf34c9b6fcd22338ef764b039b3ac55ed0e297b reverted.
--
Cheers,
Alistair.
Third year Computer Science undergraduate.
1F2 55 South Clerk Street, Edinburgh, UK.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Linux v2.6.17-rc4
2006-05-15 5:27 ` Alistair John Strachan
@ 2006-05-20 19:11 ` Alistair John Strachan
0 siblings, 0 replies; 10+ messages in thread
From: Alistair John Strachan @ 2006-05-20 19:11 UTC (permalink / raw)
To: Ayaz Abdulla
Cc: Linus Torvalds, Linux Kernel Mailing List, jeff, netdev,
Manfred Spraul
On Monday 15 May 2006 06:27, Alistair John Strachan wrote:
> On Sunday 14 May 2006 08:57, Ayaz Abdulla wrote:
> > Alistair John Strachan wrote:
>
> [snip]
>
> > > There's been just a single commit since -rc3:
> > >
> > > forcedeth: fix multi irq issues
> > > ebf34c9b6fcd22338ef764b039b3ac55ed0e297b
> > >
> > > However, it could have just been hidden since before -rc3, so I'll try
> > > to work backwards if nobody has any immediate ideas..
> >
> > The interrupt handler could be called during the same time (on different
> > cpu) the dev->stop function is clearing out the rings (nv_txrx_reset).
>
> FWIW, I can't reproduce the fault with the commitdiff
> ebf34c9b6fcd22338ef764b039b3ac55ed0e297b reverted.
Manfred located the fault and Andrew's holding a fix for it in -mm. Hopefully
it'll end up in mainline before 2.6.17.
--
Cheers,
Alistair.
Third year Computer Science undergraduate.
1F2 55 South Clerk Street, Edinburgh, UK.
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2006-05-20 19:11 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <Pine.LNX.4.64.0605111640010.3866@g5.osdl.org>
2006-05-12 10:24 ` Linux v2.6.17-rc4 Erik Mouw
2006-05-12 10:44 ` Michael Buesch
2006-05-12 11:23 ` Olaf Hering
2006-05-12 20:54 ` Michael Buesch
2006-05-12 11:47 ` Erik Mouw
2006-05-12 20:58 ` Michael Buesch
2006-05-12 21:19 ` Alistair John Strachan
2006-05-14 7:57 ` Ayaz Abdulla
2006-05-15 5:27 ` Alistair John Strachan
2006-05-20 19:11 ` Alistair John Strachan
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).