Re: [RFC][PATCH] Add suspend and resume support to uli526x

["Rafael J. Wysocki" <rjw@sisk.pl>]

Hi,

On Monday, 4 June 2007 13:11, Pavel Machek wrote:
> Hi!
> 
> > From: Rafael J. Wysocki <rjw@sisk.pl>
> > 
> > Add suspend/resume support to the uli526x network driver (tested on x86_64,
> > with 'Ethernet controller: ALi Corporation M5263 Ethernet Controller, rev 40').
> > 
> > Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
> 
> Looks ok to me.
> 
> > +#ifdef CONFIG_PM
> > +
> > +/*
> > + *	Suspend the interface.
> > + */
> > +
> > +static int uli526x_suspend(struct pci_dev *pdev, pm_message_t state)
> > +{
> > +	struct net_device *dev = pci_get_drvdata(pdev);
> > +
> > +	ULI526X_DBUG(0, "uli526x_suspend", 0);
> > +
> > +	if (dev && netdev_priv(dev)) {
> > +		if (netif_running(dev)) {
> > +			netif_device_detach(dev);
> > +			uli526x_down(dev);
> > +		}
> > +		pci_save_state(pdev);
> > +		pci_enable_wake(pdev, pci_choose_state(pdev, state), 0);
> > +		pci_disable_device(pdev);
> > +		pci_set_power_state(pdev, pci_choose_state(pdev, state));
> > +	}
> > +	return 0;
> > +}
> > +
> > +/*
> > + *	Resume the interface.
> > + */
> > +
> > +static int uli526x_resume(struct pci_dev *pdev)
> > +{
> > +	struct net_device *dev = pci_get_drvdata(pdev);
> > +	struct uli526x_board_info *db = netdev_priv(dev);
> > +	int err;
> > +
> > +	ULI526X_DBUG(0, "uli526x_resume", 0);
> > +
> > +	if (dev && db) {
> > +		pci_set_power_state(pdev, PCI_D0);
> > +		err = pci_enable_device(pdev);
> > +		if (err) {
> > +			printk(KERN_WARNING "%s: Could not enable device \n",
> > +				dev->name);
> > +			return err;
> > +		}
> > +		pci_restore_state(pdev);
> > +		pci_set_master(pdev);
> > +		if (netif_running(dev)) {
> > +			uli526x_up(dev);
> > +			netif_device_attach(dev);
> > +		}
> > +	}
> > +	return 0;
> > +}
> > +
> #else 
> #define *_resume NULL
> #define *_suspend NULL

> > +#endif /* CONFIG_PM */
> 
> > @@ -1689,6 +1775,10 @@ static struct pci_driver uli526x_driver 
> >  	.id_table	= uli526x_pci_tbl,
> >  	.probe		= uli526x_init_one,
> >  	.remove		= __devexit_p(uli526x_remove_one),
> > +#ifdef CONFIG_PM
> > +	.suspend	= uli526x_suspend,
> > +	.resume		= uli526x_resume,
> > +#endif
> 
> ...so that this ifdef is not needed?

OK, why not.

Greetings,
Rafael


-- 
"Premature optimization is the root of all evil." - Donald Knuth