via-rhine: Transmit timed out problem

via-rhine: Transmit timed out problem

[Kirill Kuvaldin]

Hi,

I'm experiencing a strange problem with a via rhine network card on Ubuntu 
7.04 (2.6.20-16-generic #2 SMP). The hardware seemed to come into an
inconsistent state, since rmmod'ing and modprobe'ing the via-rhine driver 
back didn't help. 

After the problem had appeared, I could see the following in dmesg:

[ 8601.971189] irq 21: nobody cared (try booting with the "irqpoll"
option)
[ 8601.971214]  [<c01543a4>] __report_bad_irq+0x24/0x80
[ 8601.971229]  [<c015465e>] note_interrupt+0x25e/0x290
[ 8601.971238]  [<c01538d0>] handle_IRQ_event+0x30/0x60
[ 8601.971245]  [<c0154f91>] handle_fasteoi_irq+0xc1/0xf0
[ 8601.971252]  [<c0105b70>] do_IRQ+0x40/0x80
[ 8601.971259]  [<c0104233>] common_interrupt+0x23/0x30
[ 8601.971269]  [<c01012b6>] mwait_idle_with_hints+0x46/0x60
[ 8601.971276]  [<c0101409>] cpu_idle+0x49/0xd0
[ 8601.971289]  =======================
[ 8601.971291] handlers:
[ 8601.971293] [<f887ff10>] (usb_hcd_irq+0x0/0x60 [usbcore])
[ 8601.971311] [<f88a7dd0>] (rhine_interrupt+0x0/0xb80 [via_rhine])
[ 8601.971324] Disabling IRQ #21
[ 8637.970985] NETDEV WATCHDOG: eth0: transmit timed out
[ 8637.971135] eth0: Transmit timed out, status 1003, PHY status 786d,
resetting
[ 8637.971163] via-rhine: Reset not complete yet. Trying harder.
[ 8637.971754] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 8640.749432] via-rhine: Reset not complete yet. Trying harder.
[ 8640.750018] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 8644.746689] NETDEV WATCHDOG: eth0: transmit timed out
[ 8644.746838] eth0: Transmit timed out, status 0003, PHY status 786d,
resetting
[ 8644.747446] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 8648.743327] NETDEV WATCHDOG: eth0: transmit timed out
[ 8648.743476] eth0: Transmit timed out, status 0003, PHY status 786d,
resetting
[ 8648.744083] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 8651.070635] eth0: no IPv6 routers present
[ 8670.723818] NETDEV WATCHDOG: eth0: transmit timed out
[ 8670.723968] eth0: Transmit timed out, status 0003, PHY status 786d,
resetting
[ 8670.723995] via-rhine: Reset not complete yet. Trying harder.
[ 8670.724578] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 8726.668036] NETDEV WATCHDOG: eth0: transmit timed out


The interrupt seemed to be unhandled and got disabled by the kernel
then. The transmission seemed to time out for some reason (probably, the
hardware got into an inconsistent state?).


Some related information:

kuvkir@coreduo:~% lspci |grep -i rhine
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II]
(rev 7c)
kuvkir@coreduo:~% uname -a
Linux coreduo 2.6.20-16-generic #2 SMP Thu Jun 7 20:19:32 UTC 2007 i686
GNU/Linux
kuvkir@coreduo:~% dmesg|grep rhine
[    2.982700] via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald
Becker

Is that information sufficient for debug? Let me know if you need
any additional data.


  Kirill

Re: via-rhine: Transmit timed out problem

[Jarek Poplawski]

On 22-06-2007 14:18, Kirill Kuvaldin wrote:
> Hi,
> 
> I'm experiencing a strange problem with a via rhine network card on Ubuntu 
> 7.04 (2.6.20-16-generic #2 SMP). The hardware seemed to come into an
> inconsistent state, since rmmod'ing and modprobe'ing the via-rhine driver 
> back didn't help. 
> 
> After the problem had appeared, I could see the following in dmesg:
> 
> [ 8601.971189] irq 21: nobody cared (try booting with the "irqpoll"
> option)
> [ 8601.971214]  [<c01543a4>] __report_bad_irq+0x24/0x80
...
> [ 8601.971291] handlers:
> [ 8601.971293] [<f887ff10>] (usb_hcd_irq+0x0/0x60 [usbcore])
> [ 8601.971311] [<f88a7dd0>] (rhine_interrupt+0x0/0xb80 [via_rhine])
> [ 8601.971324] Disabling IRQ #21
...
> The interrupt seemed to be unhandled and got disabled by the kernel
> then. The transmission seemed to time out for some reason (probably, the
> hardware got into an inconsistent state?).
...
> Is that information sufficient for debug? Let me know if you need
> any additional data.

Your diagnose seems right but there are at least 2 suspects.
I doubt I can debug this, but maybe trying this "irqpoll" could
really tell more to somebody.

You could probably try to check this without USB (e.g. with kernel
parameter "nousb"), too.

Regards,
Jarek P.