From mboxrd@z Thu Jan 1 00:00:00 1970 From: "Denys Fedoryshchenko" Subject: netconsole on bnx2 not working? Date: Sun, 20 Jan 2008 17:54:31 +0200 Message-ID: <20080120154119.M46441@visp.net.lb> Mime-Version: 1.0 Content-Type: text/plain; charset=koi8-r To: netdev@vger.kernel.org Return-path: Received: from usermail.globalproof.net ([194.146.153.18]:49062 "EHLO usermail.globalproof.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1753662AbYATPyv (ORCPT ); Sun, 20 Jan 2008 10:54:51 -0500 Received: from visp.net.lb (localhost [127.0.0.1]) by usermail.globalproof.net (Postfix) with ESMTP id 23F82BC821 for ; Sun, 20 Jan 2008 17:54:31 +0200 (EET) Sender: netdev-owner@vger.kernel.org List-ID: Hi I am trying to run netconsole on Dell PowerEdge 1950, equipped with two Broadcom NIC, without any success. Tried to load netconsole on eth1 and eth0 (interface was renamed by udev), and after that i am loading ppp_generic (which generate some data in kernel log). Watching by tcpdump on remote, and local host - nothing is shown there. The same time i am testing on RTL8139, same commands(just ip/mac different, and sure machine is different) work fine. Is any specific reason for that here? How i can debug this issue? Do i need to enable netpoll for that? I tried to create target over configfs, without any luck. Still no data is sent. visp-1 test # pwd /config/netconsole/test visp-1 test # ls dev_name enabled local_ip local_mac local_port remote_ip remote_mac remote_port visp-1 test # grep "" * dev_name:eth0 enabled:1 local_ip:217.151.X.Y local_mac:00:13:72:f8:73:ac local_port:6665 remote_ip:217.151.X.X remote_mac:00:30:48:90:09:06 remote_port:514 dmesg [537625.200501] Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.6.9 (December 8, 2007) [537625.200888] ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [537625.531219] eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B1) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 16, node addr 00:13:72:f8:73:ae [537625.531268] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [537625.532352] udev: renamed network interface eth0 to eth1 [537625.888397] eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B1) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 16, node addr 00:13:72:f8:73:ac dmesg on loading netconsole on eth0 and eth1 [538036.561776] netconsole: local port 111 [538036.561785] netconsole: local IP 217.151.X.X [538036.561789] netconsole: interface eth1 [538036.561793] netconsole: remote port 514 [538036.561802] netconsole: remote IP 217.151.X.X [538036.561808] netconsole: remote ethernet address 00:30:48:90:09:06 [538036.565989] console [netcon0] enabled [538036.565998] netconsole: network logging started [537899.157053] netconsole: couldn't parse config at 217.151.224.117! [537899.157064] netconsole: cleaning up [537942.772496] netconsole: local port 111 [537942.772505] netconsole: local IP 217.151.X.X [537942.772510] netconsole: interface eth0 [537942.772514] netconsole: remote port 514 [537942.772518] netconsole: remote IP 217.151.X.X [537942.772549] netconsole: remote ethernet address 00:30:48:90:09:06 [537942.780203] console [netcon0] enabled [537942.780213] netconsole: network logging started -- Denys Fedoryshchenko Technical Manager Virtual ISP S.A.L.