[PATCH v2.6.26 0/2] Dynamic TBIPA for gianfar

[PATCH v2.6.26 0/2] Dynamic TBIPA for gianfar

[Paul Gortmaker]

These patches allow boards with a PHY at the end of the bus to function,
by having the TBIPA set dynamically.  The 1st patch factors out some of
the PHY probe code so it can be recycled by the TBIPA probe, and the
second patch implements the dynamic probe itself.

Paul.

[PATCH v2.6.26 1/2] phylib: factor out get_phy_id from within get_phy_device

[Paul Gortmaker]

We were already doing what amounts to a get_phy_id from within
get_phy_device, and rather than duplicate this for the TBIPA
probing, we might as well just factor it out and make it available
instead.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andy Fleming <afleming@freescale.com>
---
 drivers/net/phy/phy_device.c |   38 +++++++++++++++++++++++++++++---------
 include/linux/phy.h          |    1 +
 2 files changed, 30 insertions(+), 9 deletions(-)

diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index f4c4fd8..8b1121b 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -86,35 +86,55 @@ struct phy_device* phy_device_create(struct mii_bus *bus, int addr, int phy_id)
 EXPORT_SYMBOL(phy_device_create);
 
 /**
- * get_phy_device - reads the specified PHY device and returns its @phy_device struct
+ * get_phy_id - reads the specified addr for its ID.
  * @bus: the target MII bus
  * @addr: PHY address on the MII bus
+ * @phy_id: where to store the ID retrieved.
  *
  * Description: Reads the ID registers of the PHY at @addr on the
- *   @bus, then allocates and returns the phy_device to represent it.
+ *   @bus, stores it in @phy_id and returns zero on success.
  */
-struct phy_device * get_phy_device(struct mii_bus *bus, int addr)
+int get_phy_id(struct mii_bus *bus, int addr, u32 *phy_id)
 {
 	int phy_reg;
-	u32 phy_id;
-	struct phy_device *dev = NULL;
 
 	/* Grab the bits from PHYIR1, and put them
 	 * in the upper half */
 	phy_reg = bus->read(bus, addr, MII_PHYSID1);
 
 	if (phy_reg < 0)
-		return ERR_PTR(phy_reg);
+		return -EIO;
 
-	phy_id = (phy_reg & 0xffff) << 16;
+	*phy_id = (phy_reg & 0xffff) << 16;
 
 	/* Grab the bits from PHYIR2, and put them in the lower half */
 	phy_reg = bus->read(bus, addr, MII_PHYSID2);
 
 	if (phy_reg < 0)
-		return ERR_PTR(phy_reg);
+		return -EIO;
+
+	*phy_id |= (phy_reg & 0xffff);
+
+	return 0;
+}
+
+/**
+ * get_phy_device - reads the specified PHY device and returns its @phy_device struct
+ * @bus: the target MII bus
+ * @addr: PHY address on the MII bus
+ *
+ * Description: Reads the ID registers of the PHY at @addr on the
+ *   @bus, then allocates and returns the phy_device to represent it.
+ */
+struct phy_device * get_phy_device(struct mii_bus *bus, int addr)
+{
+	struct phy_device *dev = NULL;
+	u32 phy_id;
+	int r;
 
-	phy_id |= (phy_reg & 0xffff);
+	r = get_phy_id(bus, addr, &phy_id);
+	if (r)
+		return ERR_PTR(r);
 
 	/* If the phy_id is all Fs, there is no device there */
 	if (0xffffffff == phy_id)
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 5e43ae7..e794c4d 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -361,6 +361,7 @@ struct phy_driver {
 
 int phy_read(struct phy_device *phydev, u16 regnum);
 int phy_write(struct phy_device *phydev, u16 regnum, u16 val);
+int get_phy_id(struct mii_bus *bus, int addr, u32 *phy_id);
 struct phy_device* get_phy_device(struct mii_bus *bus, int addr);
 int phy_clear_interrupt(struct phy_device *phydev);
 int phy_config_interrupt(struct phy_device *phydev, u32 interrupts);
-- 
1.5.4.3

[PATCH v2.6.26 2/2] gianfar: Determine TBIPA value dynamically

[Paul Gortmaker]

TBIPA needs to be set to a value (on connected MDIO buses) that doesn't
conflict with PHYs on the bus.  By hardcoding it to 0x1f, we were preventing
boards with PHYs at 0x1f from working properly.  Instead, scan the bus when
it comes up, and find an address that doesn't have a PHY on it.  The TBI PHY
configuration code then trusts that the value in TBIPA is either safe, or
doesn't matter (ie - it's not an active bus with other PHYs).

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
 drivers/net/gianfar.c     |   27 ++++++++++++++-------------
 drivers/net/gianfar.h     |    1 -
 drivers/net/gianfar_mii.c |   38 +++++++++++++++++++++++++++++++++-----
 drivers/net/gianfar_mii.h |    3 +++
 4 files changed, 50 insertions(+), 19 deletions(-)

diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c
index 718cf77..b30809b 100644
--- a/drivers/net/gianfar.c
+++ b/drivers/net/gianfar.c
@@ -130,8 +130,6 @@ static void free_skb_resources(struct gfar_private *priv);
 static void gfar_set_multi(struct net_device *dev);
 static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr);
 static void gfar_configure_serdes(struct net_device *dev);
-extern int gfar_local_mdio_write(struct gfar_mii __iomem *regs, int mii_id, int regnum, u16 value);
-extern int gfar_local_mdio_read(struct gfar_mii __iomem *regs, int mii_id, int regnum);
 #ifdef CONFIG_GFAR_NAPI
 static int gfar_poll(struct napi_struct *napi, int budget);
 #endif
@@ -476,24 +474,30 @@ static int init_phy(struct net_device *dev)
 	return 0;
 }
 
+/*
+ * Initialize TBI PHY interface for communicating with the
+ * SERDES lynx PHY on the chip.  We communicate with this PHY
+ * through the MDIO bus on each controller, treating it as a
+ * "normal" PHY at the address found in the TBIPA register.  We assume
+ * that the TBIPA register is valid.  Either the MDIO bus code will set
+ * it to a value that doesn't conflict with other PHYs on the bus, or the
+ * value doesn't matter, as there are no other PHYs on the bus.
+ */
 static void gfar_configure_serdes(struct net_device *dev)
 {
 	struct gfar_private *priv = netdev_priv(dev);
 	struct gfar_mii __iomem *regs =
 			(void __iomem *)&priv->regs->gfar_mii_regs;
+	int tbipa = gfar_read(&priv->regs->tbipa);
 
-	/* Initialise TBI i/f to communicate with serdes (lynx phy) */
+	/* Single clk mode, mii mode off(for serdes communication) */
+	gfar_local_mdio_write(regs, tbipa, MII_TBICON, TBICON_CLK_SELECT);
 
-	/* Single clk mode, mii mode off(for aerdes communication) */
-	gfar_local_mdio_write(regs, TBIPA_VALUE, MII_TBICON, TBICON_CLK_SELECT);
-
-	/* Supported pause and full-duplex, no half-duplex */
-	gfar_local_mdio_write(regs, TBIPA_VALUE, MII_ADVERTISE,
+	gfar_local_mdio_write(regs, tbipa, MII_ADVERTISE,
 			ADVERTISE_1000XFULL | ADVERTISE_1000XPAUSE |
 			ADVERTISE_1000XPSE_ASYM);
 
-	/* ANEG enable, restart ANEG, full duplex mode, speed[1] set */
-	gfar_local_mdio_write(regs, TBIPA_VALUE, MII_BMCR, BMCR_ANENABLE |
+	gfar_local_mdio_write(regs, tbipa, MII_BMCR, BMCR_ANENABLE |
 			BMCR_ANRESTART | BMCR_FULLDPLX | BMCR_SPEED1000);
 }
 
@@ -540,9 +544,6 @@ static void init_registers(struct net_device *dev)
 
 	/* Initialize the Minimum Frame Length Register */
 	gfar_write(&priv->regs->minflr, MINFLR_INIT_SETTINGS);
-
-	/* Assign the TBI an address which won't conflict with the PHYs */
-	gfar_write(&priv->regs->tbipa, TBIPA_VALUE);
 }
 
 
diff --git a/drivers/net/gianfar.h b/drivers/net/gianfar.h
index 46cd773..771aa5e 100644
--- a/drivers/net/gianfar.h
+++ b/drivers/net/gianfar.h
@@ -130,7 +130,6 @@ extern const char gfar_driver_version[];
 #define DEFAULT_RXCOUNT	16
 #define DEFAULT_RXTIME	4
 
-#define TBIPA_VALUE		0x1f
 #define MIIMCFG_INIT_VALUE	0x00000007
 #define MIIMCFG_RESET           0x80000000
 #define MIIMIND_BUSY            0x00000001
diff --git a/drivers/net/gianfar_mii.c b/drivers/net/gianfar_mii.c
index 2432762..4f23e60 100644
--- a/drivers/net/gianfar_mii.c
+++ b/drivers/net/gianfar_mii.c
@@ -78,7 +78,6 @@ int gfar_local_mdio_write(struct gfar_mii __iomem *regs, int mii_id,
  * same as system mdio bus, used for controlling the external PHYs, for eg.
  */
 int gfar_local_mdio_read(struct gfar_mii __iomem *regs, int mii_id, int regnum)
-
 {
 	u16 value;
 
@@ -122,7 +121,7 @@ int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
 }
 
 /* Reset the MIIM registers, and wait for the bus to free */
-int gfar_mdio_reset(struct mii_bus *bus)
+static int gfar_mdio_reset(struct mii_bus *bus)
 {
 	struct gfar_mii __iomem *regs = (void __iomem *)bus->priv;
 	unsigned int timeout = PHY_INIT_TIMEOUT;
@@ -152,14 +151,15 @@ int gfar_mdio_reset(struct mii_bus *bus)
 }
 
 
-int gfar_mdio_probe(struct device *dev)
+static int gfar_mdio_probe(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct gianfar_mdio_data *pdata;
 	struct gfar_mii __iomem *regs;
+	struct gfar __iomem *enet_regs;
 	struct mii_bus *new_bus;
 	struct resource *r;
-	int err = 0;
+	int i, err = 0;
 
 	if (NULL == dev)
 		return -EINVAL;
@@ -199,6 +199,34 @@ int gfar_mdio_probe(struct device *dev)
 	new_bus->dev = dev;
 	dev_set_drvdata(dev, new_bus);
 
+	/*
+	 * This is mildly evil, but so is our hardware for doing this.
+	 * Also, we have to cast back to struct gfar_mii because of
+	 * definition weirdness done in gianfar.h.
+	 */
+	enet_regs = (struct gfar __iomem *)
+		((char *)regs - offsetof(struct gfar, gfar_mii_regs));
+
+	/* Scan the bus, looking for an empty spot for TBIPA */
+	gfar_write(&enet_regs->tbipa, 0);
+	for (i = PHY_MAX_ADDR; i > 0; i--) {
+		u32 phy_id;
+		int r;
+
+		r = get_phy_id(new_bus, i, &phy_id);
+		if (r)
+			return r;
+
+		if (phy_id == 0xffffffff)
+			break;
+	}
+
+	/* The bus is full.  We don't support using 31 PHYs, sorry */
+	if (i == 0)
+		return -EBUSY;
+
+	gfar_write(&enet_regs->tbipa, i);
+
 	err = mdiobus_register(new_bus);
 
 	if (0 != err) {
@@ -218,7 +246,7 @@ reg_map_fail:
 }
 
 
-int gfar_mdio_remove(struct device *dev)
+static int gfar_mdio_remove(struct device *dev)
 {
 	struct mii_bus *bus = dev_get_drvdata(dev);
 
diff --git a/drivers/net/gianfar_mii.h b/drivers/net/gianfar_mii.h
index b373091..2af28b1 100644
--- a/drivers/net/gianfar_mii.h
+++ b/drivers/net/gianfar_mii.h
@@ -41,6 +41,9 @@ struct gfar_mii {
 
 int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum);
 int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value);
+int gfar_local_mdio_write(struct gfar_mii __iomem *regs, int mii_id,
+			  int regnum, u16 value);
+int gfar_local_mdio_read(struct gfar_mii __iomem *regs, int mii_id, int regnum);
 int __init gfar_mdio_init(void);
 void gfar_mdio_exit(void);
 #endif /* GIANFAR_PHY_H */
-- 
1.5.4.3

Re: [PATCH v2.6.26 2/2] gianfar: Determine TBIPA value dynamically

[Jeff Garzik]

Paul Gortmaker wrote:
> TBIPA needs to be set to a value (on connected MDIO buses) that doesn't
> conflict with PHYs on the bus.  By hardcoding it to 0x1f, we were preventing
> boards with PHYs at 0x1f from working properly.  Instead, scan the bus when
> it comes up, and find an address that doesn't have a PHY on it.  The TBI PHY
> configuration code then trusts that the value in TBIPA is either safe, or
> doesn't matter (ie - it's not an active bus with other PHYs).
> 
> Signed-off-by: Andy Fleming <afleming@freescale.com>
> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
> ---
>  drivers/net/gianfar.c     |   27 ++++++++++++++-------------
>  drivers/net/gianfar.h     |    1 -
>  drivers/net/gianfar_mii.c |   38 +++++++++++++++++++++++++++++++++-----
>  drivers/net/gianfar_mii.h |    3 +++
>  4 files changed, 50 insertions(+), 19 deletions(-)

ACK, but failed to apply

please rediff against jgarzik/netdev-2.6.git#upstream or its parent, 
davem/net-2.6.26.git

Re: [PATCH v2.6.26 2/2] gianfar: Determine TBIPA value dynamically

[Paul Gortmaker]

In message: Re: [PATCH v2.6.26 2/2] gianfar: Determine TBIPA value dynamically
on 16/04/2008 Jeff Garzik wrote:

>
> ACK, but failed to apply
>
> please rediff against jgarzik/netdev-2.6.git#upstream or its parent,  
> davem/net-2.6.26.git

Re-diffed against davem/net-2.6.26.git -- this minor change in the context:

-#define DEFAULT_RXTIME 4
+#define DEFAULT_RXTIME 21

overlapped with this patch and caused git to get upset about fuzz.
Other than this context change, the patch is identical to what you've
already reviewed.

Thanks,
Paul.
---

 From 1f78c8a708b5424fdba33320591258a033f079cd Mon Sep 17 00:00:00 2001
From: Paul Gortmaker <paul.gortmaker@windriver.com>
Date: Tue, 15 Apr 2008 12:23:21 -0400
Subject: [PATCH] gianfar: Determine TBIPA value dynamically

TBIPA needs to be set to a value (on connected MDIO buses) that doesn't
conflict with PHYs on the bus.  By hardcoding it to 0x1f, we were preventing
boards with PHYs at 0x1f from working properly.  Instead, scan the bus when
it comes up, and find an address that doesn't have a PHY on it.  The TBI PHY
configuration code then trusts that the value in TBIPA is either safe, or
doesn't matter (ie - it's not an active bus with other PHYs).

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
 drivers/net/gianfar.c     |   27 ++++++++++++++-------------
 drivers/net/gianfar.h     |    1 -
 drivers/net/gianfar_mii.c |   38 +++++++++++++++++++++++++++++++++-----
 drivers/net/gianfar_mii.h |    3 +++
 4 files changed, 50 insertions(+), 19 deletions(-)

diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c
index 601f93e..727e687 100644
--- a/drivers/net/gianfar.c
+++ b/drivers/net/gianfar.c
@@ -130,8 +130,6 @@ static void free_skb_resources(struct gfar_private *priv);
 static void gfar_set_multi(struct net_device *dev);
 static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr);
 static void gfar_configure_serdes(struct net_device *dev);
-extern int gfar_local_mdio_write(struct gfar_mii __iomem *regs, int mii_id, int regnum, u16 value);
-extern int gfar_local_mdio_read(struct gfar_mii __iomem *regs, int mii_id, int regnum);
 #ifdef CONFIG_GFAR_NAPI
 static int gfar_poll(struct napi_struct *napi, int budget);
 #endif
@@ -476,24 +474,30 @@ static int init_phy(struct net_device *dev)
 	return 0;
 }
 
+/*
+ * Initialize TBI PHY interface for communicating with the
+ * SERDES lynx PHY on the chip.  We communicate with this PHY
+ * through the MDIO bus on each controller, treating it as a
+ * "normal" PHY at the address found in the TBIPA register.  We assume
+ * that the TBIPA register is valid.  Either the MDIO bus code will set
+ * it to a value that doesn't conflict with other PHYs on the bus, or the
+ * value doesn't matter, as there are no other PHYs on the bus.
+ */
 static void gfar_configure_serdes(struct net_device *dev)
 {
 	struct gfar_private *priv = netdev_priv(dev);
 	struct gfar_mii __iomem *regs =
 			(void __iomem *)&priv->regs->gfar_mii_regs;
+	int tbipa = gfar_read(&priv->regs->tbipa);
 
-	/* Initialise TBI i/f to communicate with serdes (lynx phy) */
+	/* Single clk mode, mii mode off(for serdes communication) */
+	gfar_local_mdio_write(regs, tbipa, MII_TBICON, TBICON_CLK_SELECT);
 
-	/* Single clk mode, mii mode off(for aerdes communication) */
-	gfar_local_mdio_write(regs, TBIPA_VALUE, MII_TBICON, TBICON_CLK_SELECT);
-
-	/* Supported pause and full-duplex, no half-duplex */
-	gfar_local_mdio_write(regs, TBIPA_VALUE, MII_ADVERTISE,
+	gfar_local_mdio_write(regs, tbipa, MII_ADVERTISE,
 			ADVERTISE_1000XFULL | ADVERTISE_1000XPAUSE |
 			ADVERTISE_1000XPSE_ASYM);
 
-	/* ANEG enable, restart ANEG, full duplex mode, speed[1] set */
-	gfar_local_mdio_write(regs, TBIPA_VALUE, MII_BMCR, BMCR_ANENABLE |
+	gfar_local_mdio_write(regs, tbipa, MII_BMCR, BMCR_ANENABLE |
 			BMCR_ANRESTART | BMCR_FULLDPLX | BMCR_SPEED1000);
 }
 
@@ -540,9 +544,6 @@ static void init_registers(struct net_device *dev)
 
 	/* Initialize the Minimum Frame Length Register */
 	gfar_write(&priv->regs->minflr, MINFLR_INIT_SETTINGS);
-
-	/* Assign the TBI an address which won't conflict with the PHYs */
-	gfar_write(&priv->regs->tbipa, TBIPA_VALUE);
 }
 
 
diff --git a/drivers/net/gianfar.h b/drivers/net/gianfar.h
index ea8671f..4f92eb7 100644
--- a/drivers/net/gianfar.h
+++ b/drivers/net/gianfar.h
@@ -130,7 +130,6 @@ extern const char gfar_driver_version[];
 #define DEFAULT_RXCOUNT	16
 #define DEFAULT_RXTIME	21
 
-#define TBIPA_VALUE		0x1f
 #define MIIMCFG_INIT_VALUE	0x00000007
 #define MIIMCFG_RESET           0x80000000
 #define MIIMIND_BUSY            0x00000001
diff --git a/drivers/net/gianfar_mii.c b/drivers/net/gianfar_mii.c
index 2432762..4f23e60 100644
--- a/drivers/net/gianfar_mii.c
+++ b/drivers/net/gianfar_mii.c
@@ -78,7 +78,6 @@ int gfar_local_mdio_write(struct gfar_mii __iomem *regs, int mii_id,
  * same as system mdio bus, used for controlling the external PHYs, for eg.
  */
 int gfar_local_mdio_read(struct gfar_mii __iomem *regs, int mii_id, int regnum)
-
 {
 	u16 value;
 
@@ -122,7 +121,7 @@ int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
 }
 
 /* Reset the MIIM registers, and wait for the bus to free */
-int gfar_mdio_reset(struct mii_bus *bus)
+static int gfar_mdio_reset(struct mii_bus *bus)
 {
 	struct gfar_mii __iomem *regs = (void __iomem *)bus->priv;
 	unsigned int timeout = PHY_INIT_TIMEOUT;
@@ -152,14 +151,15 @@ int gfar_mdio_reset(struct mii_bus *bus)
 }
 
 
-int gfar_mdio_probe(struct device *dev)
+static int gfar_mdio_probe(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct gianfar_mdio_data *pdata;
 	struct gfar_mii __iomem *regs;
+	struct gfar __iomem *enet_regs;
 	struct mii_bus *new_bus;
 	struct resource *r;
-	int err = 0;
+	int i, err = 0;
 
 	if (NULL == dev)
 		return -EINVAL;
@@ -199,6 +199,34 @@ int gfar_mdio_probe(struct device *dev)
 	new_bus->dev = dev;
 	dev_set_drvdata(dev, new_bus);
 
+	/*
+	 * This is mildly evil, but so is our hardware for doing this.
+	 * Also, we have to cast back to struct gfar_mii because of
+	 * definition weirdness done in gianfar.h.
+	 */
+	enet_regs = (struct gfar __iomem *)
+		((char *)regs - offsetof(struct gfar, gfar_mii_regs));
+
+	/* Scan the bus, looking for an empty spot for TBIPA */
+	gfar_write(&enet_regs->tbipa, 0);
+	for (i = PHY_MAX_ADDR; i > 0; i--) {
+		u32 phy_id;
+		int r;
+
+		r = get_phy_id(new_bus, i, &phy_id);
+		if (r)
+			return r;
+
+		if (phy_id == 0xffffffff)
+			break;
+	}
+
+	/* The bus is full.  We don't support using 31 PHYs, sorry */
+	if (i == 0)
+		return -EBUSY;
+
+	gfar_write(&enet_regs->tbipa, i);
+
 	err = mdiobus_register(new_bus);
 
 	if (0 != err) {
@@ -218,7 +246,7 @@ reg_map_fail:
 }
 
 
-int gfar_mdio_remove(struct device *dev)
+static int gfar_mdio_remove(struct device *dev)
 {
 	struct mii_bus *bus = dev_get_drvdata(dev);
 
diff --git a/drivers/net/gianfar_mii.h b/drivers/net/gianfar_mii.h
index b373091..2af28b1 100644
--- a/drivers/net/gianfar_mii.h
+++ b/drivers/net/gianfar_mii.h
@@ -41,6 +41,9 @@ struct gfar_mii {
 
 int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum);
 int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value);
+int gfar_local_mdio_write(struct gfar_mii __iomem *regs, int mii_id,
+			  int regnum, u16 value);
+int gfar_local_mdio_read(struct gfar_mii __iomem *regs, int mii_id, int regnum);
 int __init gfar_mdio_init(void);
 void gfar_mdio_exit(void);
 #endif /* GIANFAR_PHY_H */
-- 
1.5.4.3



>
>

Re: [PATCH v2.6.26 2/2] gianfar: Determine TBIPA value dynamically

[Jeff Garzik]

Paul Gortmaker wrote:
> In message: Re: [PATCH v2.6.26 2/2] gianfar: Determine TBIPA value dynamically
> on 16/04/2008 Jeff Garzik wrote:
> 
>> ACK, but failed to apply
>>
>> please rediff against jgarzik/netdev-2.6.git#upstream or its parent,  
>> davem/net-2.6.26.git
> 
> Re-diffed against davem/net-2.6.26.git -- this minor change in the context:
> 
> -#define DEFAULT_RXTIME 4
> +#define DEFAULT_RXTIME 21
> 
> overlapped with this patch and caused git to get upset about fuzz.
> Other than this context change, the patch is identical to what you've
> already reviewed.
> 
> Thanks,
> Paul.
> ---
> 
>  From 1f78c8a708b5424fdba33320591258a033f079cd Mon Sep 17 00:00:00 2001
> From: Paul Gortmaker <paul.gortmaker@windriver.com>
> Date: Tue, 15 Apr 2008 12:23:21 -0400
> Subject: [PATCH] gianfar: Determine TBIPA value dynamically
> 
> TBIPA needs to be set to a value (on connected MDIO buses) that doesn't
> conflict with PHYs on the bus.  By hardcoding it to 0x1f, we were preventing
> boards with PHYs at 0x1f from working properly.  Instead, scan the bus when
> it comes up, and find an address that doesn't have a PHY on it.  The TBI PHY
> configuration code then trusts that the value in TBIPA is either safe, or
> doesn't matter (ie - it's not an active bus with other PHYs).
> 
> Signed-off-by: Andy Fleming <afleming@freescale.com>
> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

applied

Re: [PATCH v2.6.26 1/2] phylib: factor out get_phy_id from within get_phy_device

[Jeff Garzik]

Paul Gortmaker wrote:
> We were already doing what amounts to a get_phy_id from within
> get_phy_device, and rather than duplicate this for the TBIPA
> probing, we might as well just factor it out and make it available
> instead.
> 
> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
> Acked-by: Andy Fleming <afleming@freescale.com>
> ---
>  drivers/net/phy/phy_device.c |   38 +++++++++++++++++++++++++++++---------
>  include/linux/phy.h          |    1 +
>  2 files changed, 30 insertions(+), 9 deletions(-)

applied.

a well-split-up patch series, good show :)