From: David Miller <davem@davemloft.net>
To: mh+linux-kernel@zugschlus.de
Cc: netdev@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: 2.6.26/tg3 ping roundtrip times > 2000 ms on local network
Date: Tue, 19 Aug 2008 13:20:40 -0700 (PDT) [thread overview]
Message-ID: <20080819.132040.188336475.davem@davemloft.net> (raw)
In-Reply-To: <20080819172019.GA5823@torres.zugschlus.de>
From: Marc Haber <mh+linux-kernel@zugschlus.de>
Date: Tue, 19 Aug 2008 19:20:19 +0200
[ netdev added to CC: ]
> I have one HP DL 140 G1 running with Debian stable and a
> locally-built, vanilla kernel. With 2.6.25.11, everything is fine.
>
> But, after updating to 2.6.26.2, I noticed that pinging the host on
> the local ethernet sometimes (e.g. several times a minute, but not
> always) results in a round-trip time of larger than two seconds. The
> packets are not lost though, they're only severly delayed. For an ssh
> session to the host, this feels like somebody rocking a bad network
> connector. The same behavior is visible with 2.6.26 and 2.6.26.1.
>
> Going back to 2.6.25.11 immediately fixes the issue for me.
>
> Syslog doesn't say anything conspicious, unfortunately. As I don't
> have local access to the box, I cannot say whether it's only the
> network that freezes or whether it's the entire box.
>
> Does it make sense to test any later 2.6.25.x kernel, or is there any
> post-2.6.26 patch available that may fix the issue for me?
>
> Strangely, another DL 140 from the same charge runs just fine with
> 2.6.26.2.
>
> Here is the output of lspci -vvv for the network interface:
>
> 02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 02)
> Subsystem: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (16000ns min), Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 19
> Region 0: Memory at febc0000 (64-bit, non-prefetchable) [size=64K]
> Region 2: Memory at febb0000 (64-bit, non-prefetchable) [size=64K]
> Expansion ROM at <ignored> [disabled]
> Capabilities: [40] PCI-X non-bridge device
> Command: DPERE- ERO- RBC=2048 OST=1
> Status: Dev=02:00.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
> Capabilities: [48] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
> Capabilities: [50] Vital Product Data
> Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable-
> Address: 1502da2a94a95200 Data: 3ca4
>
> If there is any information that can help, please say so.
>
> Greetings
> Marc
>
> --
> -----------------------------------------------------------------------------
> Marc Haber | "I don't trust Computers. They | Mailadresse im Header
> Mannheim, Germany | lose things." Winona Ryder | Fon: *49 621 72739834
> Nordisch by Nature | How to make an American Quilt | Fax: *49 3221 2323190
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
next parent reply other threads:[~2008-08-19 20:20 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20080819172019.GA5823@torres.zugschlus.de>
2008-08-19 20:20 ` David Miller [this message]
2008-08-19 17:29 ` 2.6.26/tg3 ping roundtrip times > 2000 ms on local network Michael Chan
2008-08-19 22:14 ` Marc Haber
2008-08-19 22:30 ` Matt Carlson
2008-08-20 17:47 ` Marc Haber
2008-08-20 14:11 ` Michael Chan
2008-08-21 16:09 ` Marc Haber
2008-08-21 16:21 ` Michael Chan
2008-08-22 11:33 ` Marc Haber
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20080819.132040.188336475.davem@davemloft.net \
--to=davem@davemloft.net \
--cc=linux-kernel@vger.kernel.org \
--cc=mh+linux-kernel@zugschlus.de \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).