From: Ben Hutchings <bhutchings@solarflare.com>
To: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org, linux-net-drivers@solarflare.com
Subject: [PATCH 18/33] sfc: Clean up MDIO flag setting
Date: Fri, 12 Dec 2008 12:54:34 +0000 [thread overview]
Message-ID: <20081212125433.GR10372@solarflare.com> (raw)
In-Reply-To: <20081212124622.GK32518@solarflare.com>
We often want to set or clear a flag in an MDIO register, but avoid
writing if no change is required since this can have side-effects.
Encapsulate this in a function, mdio_clause45_set_flag().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
---
drivers/net/sfc/mdio_10g.c | 87 ++++++++++++++------------------------------
drivers/net/sfc/mdio_10g.h | 4 ++
2 files changed, 32 insertions(+), 59 deletions(-)
diff --git a/drivers/net/sfc/mdio_10g.c b/drivers/net/sfc/mdio_10g.c
index 1eed484..8d91131 100644
--- a/drivers/net/sfc/mdio_10g.c
+++ b/drivers/net/sfc/mdio_10g.c
@@ -205,61 +205,24 @@ bool mdio_clause45_links_ok(struct efx_nic *efx, unsigned int mmd_mask)
void mdio_clause45_transmit_disable(struct efx_nic *efx)
{
- int phy_id = efx->mii.phy_id;
- int ctrl1, ctrl2;
-
- ctrl1 = ctrl2 = mdio_clause45_read(efx, phy_id, MDIO_MMD_PMAPMD,
- MDIO_MMDREG_TXDIS);
- if (efx->phy_mode & PHY_MODE_TX_DISABLED)
- ctrl2 |= (1 << MDIO_MMDREG_TXDIS_GLOBAL_LBN);
- else
- ctrl1 &= ~(1 << MDIO_MMDREG_TXDIS_GLOBAL_LBN);
- if (ctrl1 != ctrl2)
- mdio_clause45_write(efx, phy_id, MDIO_MMD_PMAPMD,
- MDIO_MMDREG_TXDIS, ctrl2);
+ mdio_clause45_set_flag(efx, efx->mii.phy_id, MDIO_MMD_PMAPMD,
+ MDIO_MMDREG_TXDIS, MDIO_MMDREG_TXDIS_GLOBAL_LBN,
+ efx->phy_mode & PHY_MODE_TX_DISABLED);
}
void mdio_clause45_phy_reconfigure(struct efx_nic *efx)
{
int phy_id = efx->mii.phy_id;
- int ctrl1, ctrl2;
-
- /* Handle (with debouncing) PMA/PMD loopback */
- ctrl1 = ctrl2 = mdio_clause45_read(efx, phy_id, MDIO_MMD_PMAPMD,
- MDIO_MMDREG_CTRL1);
-
- if (efx->loopback_mode == LOOPBACK_PMAPMD)
- ctrl2 |= (1 << MDIO_PMAPMD_CTRL1_LBACK_LBN);
- else
- ctrl2 &= ~(1 << MDIO_PMAPMD_CTRL1_LBACK_LBN);
-
- if (ctrl1 != ctrl2)
- mdio_clause45_write(efx, phy_id, MDIO_MMD_PMAPMD,
- MDIO_MMDREG_CTRL1, ctrl2);
-
- /* Handle (with debouncing) PCS loopback */
- ctrl1 = ctrl2 = mdio_clause45_read(efx, phy_id, MDIO_MMD_PCS,
- MDIO_MMDREG_CTRL1);
- if (efx->loopback_mode == LOOPBACK_PCS)
- ctrl2 |= (1 << MDIO_MMDREG_CTRL1_LBACK_LBN);
- else
- ctrl2 &= ~(1 << MDIO_MMDREG_CTRL1_LBACK_LBN);
- if (ctrl1 != ctrl2)
- mdio_clause45_write(efx, phy_id, MDIO_MMD_PCS,
- MDIO_MMDREG_CTRL1, ctrl2);
-
- /* Handle (with debouncing) PHYXS network loopback */
- ctrl1 = ctrl2 = mdio_clause45_read(efx, phy_id, MDIO_MMD_PHYXS,
- MDIO_MMDREG_CTRL1);
- if (efx->loopback_mode == LOOPBACK_NETWORK)
- ctrl2 |= (1 << MDIO_MMDREG_CTRL1_LBACK_LBN);
- else
- ctrl2 &= ~(1 << MDIO_MMDREG_CTRL1_LBACK_LBN);
-
- if (ctrl1 != ctrl2)
- mdio_clause45_write(efx, phy_id, MDIO_MMD_PHYXS,
- MDIO_MMDREG_CTRL1, ctrl2);
+ mdio_clause45_set_flag(efx, phy_id, MDIO_MMD_PMAPMD,
+ MDIO_MMDREG_CTRL1, MDIO_PMAPMD_CTRL1_LBACK_LBN,
+ efx->loopback_mode == LOOPBACK_PMAPMD);
+ mdio_clause45_set_flag(efx, phy_id, MDIO_MMD_PCS,
+ MDIO_MMDREG_CTRL1, MDIO_MMDREG_CTRL1_LBACK_LBN,
+ efx->loopback_mode == LOOPBACK_PCS);
+ mdio_clause45_set_flag(efx, phy_id, MDIO_MMD_PHYXS,
+ MDIO_MMDREG_CTRL1, MDIO_MMDREG_CTRL1_LBACK_LBN,
+ efx->loopback_mode == LOOPBACK_NETWORK);
}
static void mdio_clause45_set_mmd_lpower(struct efx_nic *efx,
@@ -267,21 +230,13 @@ static void mdio_clause45_set_mmd_lpower(struct efx_nic *efx,
{
int phy = efx->mii.phy_id;
int stat = mdio_clause45_read(efx, phy, mmd, MDIO_MMDREG_STAT1);
- int ctrl1, ctrl2;
EFX_TRACE(efx, "Setting low power mode for MMD %d to %d\n",
mmd, lpower);
if (stat & (1 << MDIO_MMDREG_STAT1_LPABLE_LBN)) {
- ctrl1 = ctrl2 = mdio_clause45_read(efx, phy,
- mmd, MDIO_MMDREG_CTRL1);
- if (lpower)
- ctrl2 |= (1 << MDIO_MMDREG_CTRL1_LPOWER_LBN);
- else
- ctrl2 &= ~(1 << MDIO_MMDREG_CTRL1_LPOWER_LBN);
- if (ctrl1 != ctrl2)
- mdio_clause45_write(efx, phy, mmd,
- MDIO_MMDREG_CTRL1, ctrl2);
+ mdio_clause45_set_flag(efx, phy, mmd, MDIO_MMDREG_CTRL1,
+ MDIO_MMDREG_CTRL1_LPOWER_LBN, lpower);
}
}
@@ -395,3 +350,17 @@ int mdio_clause45_set_settings(struct efx_nic *efx,
return 0;
return -EOPNOTSUPP;
}
+
+void mdio_clause45_set_flag(struct efx_nic *efx, u8 prt, u8 dev,
+ u16 addr, int bit, bool sense)
+{
+ int old_val = mdio_clause45_read(efx, prt, dev, addr);
+ int new_val;
+
+ if (sense)
+ new_val = old_val | (1 << bit);
+ else
+ new_val = old_val & ~(1 << bit);
+ if (old_val != new_val)
+ mdio_clause45_write(efx, prt, dev, addr, new_val);
+}
diff --git a/drivers/net/sfc/mdio_10g.h b/drivers/net/sfc/mdio_10g.h
index 4516383..4830e0c 100644
--- a/drivers/net/sfc/mdio_10g.h
+++ b/drivers/net/sfc/mdio_10g.h
@@ -259,4 +259,8 @@ extern int mdio_clause45_set_settings(struct efx_nic *efx,
extern int mdio_clause45_wait_reset_mmds(struct efx_nic *efx,
unsigned int mmd_mask);
+/* Set or clear flag, debouncing */
+extern void mdio_clause45_set_flag(struct efx_nic *efx, u8 prt, u8 dev,
+ u16 addr, int bit, bool sense);
+
#endif /* EFX_MDIO_10G_H */
--
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
next prev parent reply other threads:[~2008-12-12 12:54 UTC|newest]
Thread overview: 74+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <cover.1229085672.git.bhutchings@solarflare.com>
2008-12-12 12:46 ` [PATCH 00/33] sfc version 2.3 Ben Hutchings
2008-12-12 12:48 ` [PATCH 01/33] sfc: Board support fixes Ben Hutchings
2008-12-13 5:29 ` David Miller
2008-12-12 12:48 ` [PATCH 02/33] sfc: Change SPI lengths to type size_t Ben Hutchings
2008-12-13 5:30 ` David Miller
2008-12-13 5:53 ` David Miller
2008-12-13 6:30 ` Ben Hutchings
2008-12-12 12:49 ` [PATCH 03/33] sfc: Do not use pci_disable_device() to disable bus mastering Ben Hutchings
2008-12-13 5:31 ` David Miller
2008-12-13 6:27 ` Ben Hutchings
2008-12-12 12:49 ` [PATCH 04/33] sfc: Remove unneeded register write Ben Hutchings
2008-12-13 5:31 ` David Miller
2008-12-12 12:49 ` [PATCH 05/33] sfc: Correct interpretation of second param to ethtool phys_id() Ben Hutchings
2008-12-13 5:32 ` David Miller
2008-12-12 12:50 ` [PATCH 06/33] sfc: Make reset_workqueue driver-global rather than per-NIC Ben Hutchings
2008-12-13 5:33 ` David Miller
2008-12-12 12:51 ` [PATCH 07/33] sfc: Clean up waits for flash/EEPROM operations Ben Hutchings
2008-12-13 5:33 ` David Miller
2008-12-12 12:51 ` [PATCH 08/33] sfc: Work around unreliable strap pins Ben Hutchings
2008-12-13 5:34 ` David Miller
2008-12-12 12:51 ` [PATCH 09/33] sfc: Restore phy_flash_cfg module parameter Ben Hutchings
2008-12-13 5:35 ` David Miller
2008-12-12 12:53 ` [PATCH 13/33] sfc: Don't count RX checksum errors during loopback self-test Ben Hutchings
2008-12-13 5:42 ` David Miller
2008-12-12 12:53 ` [PATCH 14/33] sfc: Remove MII extension cruft Ben Hutchings
2008-12-13 5:43 ` David Miller
2008-12-12 12:53 ` [PATCH 15/33] sfc: Add support for MMDs numbered >15 Ben Hutchings
2008-12-13 5:44 ` David Miller
2008-12-12 12:54 ` [PATCH 16/33] sfc: Add phy_type device attribute Ben Hutchings
2008-12-13 5:47 ` David Miller
2008-12-12 12:54 ` [PATCH 17/33] sfc: Clean up board identification Ben Hutchings
2008-12-13 5:48 ` David Miller
2008-12-12 12:54 ` Ben Hutchings [this message]
2008-12-13 5:49 ` [PATCH 18/33] sfc: Clean up MDIO flag setting David Miller
2008-12-12 12:54 ` [PATCH 19/33] sfc: Add support for sub-10G speeds Ben Hutchings
2008-12-13 5:50 ` David Miller
2008-12-12 12:55 ` [PATCH 20/33] sfc: Implement auto-negotiation Ben Hutchings
2008-12-13 5:50 ` David Miller
2008-12-12 12:55 ` [PATCH 21/33] sfc: Rework MAC, PHY and board event handling Ben Hutchings
2008-12-13 5:59 ` David Miller
2008-12-12 12:56 ` [PATCH 22/33] sfc: Add support for Solarflare 10Xpress SFT9001 Ben Hutchings
2008-12-13 6:00 ` David Miller
2008-12-12 12:56 ` [PATCH 23/33] sfc: Add support for SFN4111T Ben Hutchings
2008-12-13 6:01 ` David Miller
2008-12-12 12:56 ` [PATCH 25/33] sfc: Generate unique names for per-NIC workqueues Ben Hutchings
2008-12-13 6:04 ` David Miller
2008-12-13 6:23 ` Ben Hutchings
2008-12-13 6:29 ` David Miller
2008-12-13 14:01 ` Ben Hutchings
2008-12-12 12:57 ` [PATCH 26/33] sfc: Remove leading spaces Ben Hutchings
2008-12-13 6:05 ` David Miller
2008-12-12 12:57 ` [PATCH 27/33] sfc: Specify a meaningful component for loopback RX-side and PHY tests Ben Hutchings
2008-12-13 6:05 ` David Miller
2008-12-12 12:59 ` [PATCH 28/33] sfc: Use mutex_lock_interruptible() for ethtool EEPROM access Ben Hutchings
2008-12-13 6:06 ` David Miller
2008-12-12 12:59 ` [PATCH 29/33] sfc: Use model numbers for PHY type names Ben Hutchings
2008-12-13 6:07 ` David Miller
2008-12-12 13:00 ` [PATCH 30/33] sfc: Treat probe as unsuccessful if it scheduled a reset Ben Hutchings
2008-12-13 6:08 ` David Miller
2008-12-12 13:00 ` [PATCH 31/33] sfc: Use kzalloc() to ensure struct efx_spi_device is fully initialised Ben Hutchings
2008-12-13 6:09 ` David Miller
2008-12-12 12:52 ` [PATCH 10/33] sfc: Add option to use a separate channel for TX completions Ben Hutchings
2008-12-13 5:36 ` David Miller
2008-12-12 12:52 ` [PATCH 11/33] sfc: Provide hints to irqbalance daemon Ben Hutchings
2008-12-13 5:37 ` David Miller
2008-12-12 12:52 ` [PATCH 12/33] sfc: Abbreviate self-test names so they are not truncated Ben Hutchings
2008-12-13 5:42 ` David Miller
2008-12-12 12:56 ` [PATCH 24/33] sfc: Fix format arguments for warning about MSI-X allocation Ben Hutchings
2008-12-12 20:34 ` Ben Hutchings
2008-12-13 5:25 ` David Miller
2008-12-12 13:00 ` [PATCH 32/33] sfc: Fix synchronisation of efx_mtd_{probe,rename,remove} Ben Hutchings
2008-12-13 6:09 ` David Miller
2008-12-12 13:01 ` [PATCH 33/33] sfc: Version 2.3 Ben Hutchings
2008-12-13 6:10 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20081212125433.GR10372@solarflare.com \
--to=bhutchings@solarflare.com \
--cc=davem@davemloft.net \
--cc=linux-net-drivers@solarflare.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).