[PATCH 0/2] Blackfin EMAC driver updates

[PATCH 0/2] Blackfin EMAC driver updates

[Bryan Wu]

Hi Jeff,

Please take a look at these 2 patches for Blackfin EMAC driver

Thanks
-Bryan

[PATCH 1/2] netdev: bfin_mac: enable bfin_mac net dev driver for BF51x

[Bryan Wu]

From: Sonic Zhang <sonic.zhang@analog.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
---
 drivers/net/Kconfig |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 9a18270..6b1eb43 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -830,7 +830,7 @@ config ULTRA32
 
 config BFIN_MAC
 	tristate "Blackfin on-chip MAC support"
-	depends on NET_ETHERNET && (BF526 || BF527 || BF536 || BF537)
+	depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
 	select CRC32
 	select MII
 	select PHYLIB
-- 
1.5.6

Re: [PATCH 1/2] netdev: bfin_mac: enable bfin_mac net dev driver for BF51x

[David Miller]

From: Bryan Wu <cooloney@kernel.org>
Date: Thu,  8 Jan 2009 00:14:38 +0800

> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
> Signed-off-by: Bryan Wu <cooloney@kernel.org>

Applied.

[PATCH 2/2] netdev: bfin_mac: enable VLAN support in Blackfin MAC driver

[Bryan Wu]

From: Graf Yang <graf.yang@analog.com>

Fill EMAC_VLAN1 with 0x8100 to admit 1522 long bytes frames. EMAC_VLAN2
seems need not use for now.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
---
 drivers/net/bfin_mac.c |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)

diff --git a/drivers/net/bfin_mac.c b/drivers/net/bfin_mac.c
index 78e31aa..15d7e62 100644
--- a/drivers/net/bfin_mac.c
+++ b/drivers/net/bfin_mac.c
@@ -517,6 +517,14 @@ void setup_system_regs(struct net_device *dev)
 
 	bfin_write_EMAC_MMC_CTL(RSTC | CROLL);
 
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+#define VLAN_ETHER_TYPE 0x8100
+	/* The legal length of the frame is increased to 1522 bytes */
+	bfin_write_EMAC_VLAN1(VLAN_ETHER_TYPE);
+	/* The legal length of the frame is increased to 1538 bytes */
+	/*bfin_write_EMAC_VLAN2(VLAN_ETHER_TYPE);*/
+#endif
+
 	/* Initialize the TX DMA channel registers */
 	bfin_write_DMA2_X_COUNT(0);
 	bfin_write_DMA2_X_MODIFY(4);
-- 
1.5.6

Re: [PATCH 2/2] netdev: bfin_mac: enable VLAN support in Blackfin MAC driver

[David Miller]

From: Bryan Wu <cooloney@kernel.org>
Date: Thu,  8 Jan 2009 00:14:39 +0800

> +#define VLAN_ETHER_TYPE 0x8100

Please use ETH_P_8021Q from linux/if_ether.h instead of inventing
your own definition.

> +	/* The legal length of the frame is increased to 1538 bytes */
> +	/*bfin_write_EMAC_VLAN2(VLAN_ETHER_TYPE);*/

Please do not add code that is just going to be commented
out and not used.

Also, I disagree with the:

+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)

conditional.  Probably this part of the chip should be programmed
unconditionally.

We can get VLAN packets received and sent, using AF_PACKET
sockets, for example.  The chip should still respect those
even if VLAN proper is not being utilized.

Re: [PATCH 2/2] netdev: bfin_mac: enable VLAN support in Blackfin MAC driver

[Mike Frysinger]

On Thu, Jan 8, 2009 at 13:55, David Miller <davem@davemloft.net> wrote:
> From: Bryan Wu <cooloney@kernel.org>
>> +#define VLAN_ETHER_TYPE 0x8100
>
> Please use ETH_P_8021Q from linux/if_ether.h instead of inventing
> your own definition.

was a copy & paste due to not finding a better definition (3c59x.c)

>> +     /* The legal length of the frame is increased to 1538 bytes */
>> +     /*bfin_write_EMAC_VLAN2(VLAN_ETHER_TYPE);*/
>
> Please do not add code that is just going to be commented
> out and not used.
>
> Also, I disagree with the:
>
> +#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
>
> conditional.  Probably this part of the chip should be programmed
> unconditionally.

again, more of a copy & paste ... this is how a bunch of drivers are
doing it now ...

> We can get VLAN packets received and sent, using AF_PACKET
> sockets, for example.  The chip should still respect those
> even if VLAN proper is not being utilized.

any tips on doing that ?

thanks for reviewing!
-mike

Re: [PATCH 2/2] netdev: bfin_mac: enable VLAN support in Blackfin MAC driver

[Mike Frysinger]

On Thu, Jan 8, 2009 at 14:01, Mike Frysinger wrote:
> On Thu, Jan 8, 2009 at 13:55, David Miller wrote:
>> We can get VLAN packets received and sent, using AF_PACKET
>> sockets, for example.  The chip should still respect those
>> even if VLAN proper is not being utilized.
>
> any tips on doing that ?

or rather, is there a driver or you two you can point out that is
doing this correctly ?  the ones i looked at seemed to be doing it
like the patch we posted ...
-mike

Re: [PATCH 2/2] netdev: bfin_mac: enable VLAN support in Blackfin MAC driver

[David Miller]

From: "Mike Frysinger" <vapier.adi@gmail.com>
Date: Thu, 8 Jan 2009 14:05:33 -0500

> On Thu, Jan 8, 2009 at 14:01, Mike Frysinger wrote:
> > On Thu, Jan 8, 2009 at 13:55, David Miller wrote:
> >> We can get VLAN packets received and sent, using AF_PACKET
> >> sockets, for example.  The chip should still respect those
> >> even if VLAN proper is not being utilized.
> >
> > any tips on doing that ?
> 
> or rather, is there a driver or you two you can point out that is
> doing this correctly ?  the ones i looked at seemed to be doing it
> like the patch we posted ...

And I disagree with how those drivers are doing it :-)

At least the programming of the chip to accept all packet
types properly, VLAN or not, regardless of kernel config,
is definitely IMHO the way to go.

Re: [PATCH 2/2] netdev: bfin_mac: enable VLAN support in Blackfin MAC driver

[Mike Frysinger]

On Thu, Jan 8, 2009 at 14:30, David Miller wrote:
> From: "Mike Frysinger" <vapier
>> On Thu, Jan 8, 2009 at 14:01, Mike Frysinger wrote:
>> > On Thu, Jan 8, 2009 at 13:55, David Miller wrote:
>> >> We can get VLAN packets received and sent, using AF_PACKET
>> >> sockets, for example.  The chip should still respect those
>> >> even if VLAN proper is not being utilized.
>> >
>> > any tips on doing that ?
>>
>> or rather, is there a driver or you two you can point out that is
>> doing this correctly ?  the ones i looked at seemed to be doing it
>> like the patch we posted ...
>
> And I disagree with how those drivers are doing it :-)
>
> At least the programming of the chip to accept all packet
> types properly, VLAN or not, regardless of kernel config,
> is definitely IMHO the way to go.

i know on our side we all agree with you, we just didnt (dont) know
any better ;)
-mike

Re: [PATCH 2/2] netdev: bfin_mac: enable VLAN support in Blackfin MAC driver

[David Miller]

From: "Mike Frysinger" <vapier.adi@gmail.com>
Date: Thu, 8 Jan 2009 14:01:49 -0500

> > We can get VLAN packets received and sent, using AF_PACKET
> > sockets, for example.  The chip should still respect those
> > even if VLAN proper is not being utilized.
> 
> any tips on doing that ?

No, sorry.