netdev.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Stephen Hemminger <shemminger@vyatta.com>
To: Herbert Xu <herbert@gondor.apana.org.au>,
	David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Subject: [PATCH 2/2] sky2: add GRO support
Date: Wed, 1 Apr 2009 14:39:46 -0700	[thread overview]
Message-ID: <20090401143946.64449a05@nehalam> (raw)
In-Reply-To: <20090401142020.395f51bb@nehalam>

Add support for generic receive offload. Also cleanup counters so
that only updated once per interrupt.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
----
Note: this is experimental at this point (so please hold for 2.6.31)


--- a/drivers/net/sky2.c	2009-04-01 11:51:55.822315655 -0700
+++ b/drivers/net/sky2.c	2009-04-01 13:13:40.275066435 -0700
@@ -2344,11 +2344,46 @@ static inline void sky2_tx_done(struct n
 	}
 }
 
+static inline void sky2_skb_rx(const struct sky2_port *sky2,
+			       u32 status, struct sk_buff *skb)
+{
+#ifdef SKY2_VLAN_TAG_USED
+	u16 vlan_tag = be16_to_cpu(sky2->rx_tag);
+	if (sky2->vlgrp && (status & GMR_FS_VLAN)) {
+		if (skb->ip_summed == CHECKSUM_NONE)
+			vlan_hwaccel_receive_skb(skb, sky2->vlgrp, vlan_tag);
+		else
+			vlan_gro_receive(&sky2->hw->napi, sky2->vlgrp,
+					 vlan_tag, skb);
+		return;
+	}
+#endif
+	if (skb->ip_summed == CHECKSUM_NONE)
+		netif_receive_skb(skb);
+	else
+		napi_gro_receive(&sky2->hw->napi, skb);
+}
+
+static void sky2_rx_done(struct sky2_hw *hw, unsigned port,
+			       unsigned packets, unsigned bytes)
+{
+	struct net_device *dev = hw->dev[port];
+
+	if (dev) {
+		dev->stats.rx_packets += packets;
+		dev->stats.rx_bytes += bytes;
+		dev->last_rx = jiffies;
+		sky2_rx_update(netdev_priv(dev), rxqaddr[port]);
+	}
+}
+
+
 /* Process status response ring */
 static int sky2_status_intr(struct sky2_hw *hw, int to_do, u16 idx)
 {
 	int work_done = 0;
-	unsigned rx[2] = { 0, 0 };
+	unsigned int total_bytes[2] = { 0 };
+	unsigned int total_packets[2] = { 0 };
 
 	rmb();
 	do {
@@ -2375,7 +2410,8 @@ static int sky2_status_intr(struct sky2_
 		le->opcode = 0;
 		switch (opcode & ~HW_OWNER) {
 		case OP_RXSTAT:
-			++rx[port];
+			total_packets[port]++;
+			total_bytes[port] += length;
 			skb = sky2_receive(dev, length, status);
 			if (unlikely(!skb)) {
 				dev->stats.rx_dropped++;
@@ -2393,18 +2429,8 @@ static int sky2_status_intr(struct sky2_
 			}
 
 			skb->protocol = eth_type_trans(skb, dev);
-			dev->stats.rx_packets++;
-			dev->stats.rx_bytes += skb->len;
-			dev->last_rx = jiffies;
 
-#ifdef SKY2_VLAN_TAG_USED
-			if (sky2->vlgrp && (status & GMR_FS_VLAN)) {
-				vlan_hwaccel_receive_skb(skb,
-							 sky2->vlgrp,
-							 be16_to_cpu(sky2->rx_tag));
-			} else
-#endif
-				netif_receive_skb(skb);
+			sky2_skb_rx(sky2, status, skb);
 
 			/* Stop after net poll weight */
 			if (++work_done >= to_do)
@@ -2474,11 +2500,9 @@ static int sky2_status_intr(struct sky2_
 	sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
 
 exit_loop:
-	if (rx[0])
-		sky2_rx_update(netdev_priv(hw->dev[0]), Q_R1);
 
-	if (rx[1])
-		sky2_rx_update(netdev_priv(hw->dev[1]), Q_R2);
+	sky2_rx_done(hw, 0, total_packets[0], total_bytes[0]);
+	sky2_rx_done(hw, 1, total_packets[1], total_bytes[1]);
 
 	return work_done;
 }
@@ -4245,6 +4269,7 @@ static __devinit struct net_device *sky2
 	sky2->port = port;
 
 	dev->features |= NETIF_F_TSO | NETIF_F_IP_CSUM | NETIF_F_SG;
+	dev->features |= NETIF_F_GRO;
 	if (highmem)
 		dev->features |= NETIF_F_HIGHDMA;
 

  reply	other threads:[~2009-04-01 21:40 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2009-04-01 21:20 [PATCH 1/2] net: allow multiple dev per napi with GRO Stephen Hemminger
2009-04-01 21:39 ` Stephen Hemminger [this message]
2009-04-02  8:08   ` [PATCH 2/2] sky2: add GRO support David Miller
2009-04-02  8:08 ` [PATCH 1/2] net: allow multiple dev per napi with GRO David Miller
2009-04-02  8:28   ` Herbert Xu

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20090401143946.64449a05@nehalam \
    --to=shemminger@vyatta.com \
    --cc=davem@davemloft.net \
    --cc=herbert@gondor.apana.org.au \
    --cc=netdev@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).