[PATCH 0/6] sky2: driver update

[PATCH 0/6] sky2: driver update

[Stephen Hemminger]

This patch set adds support for Yukon Optima (88E8059) based
on the vendor driver.  Hopefully, it can go in 2.6.32.

-- 

[PATCH 1/6] sky2: add SK-9E21M device id

[Stephen Hemminger]

[-- Attachment #1: sky2-sk-9e21m.patch --]
[-- Type: text/plain, Size: 749 bytes --]

This is a new ID that just showed up in latest vendor driver.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>

--- a/drivers/net/sky2.c	2009-10-28 11:01:10.454251343 -0700
+++ b/drivers/net/sky2.c	2009-10-28 11:01:44.867001737 -0700
@@ -102,6 +102,7 @@ MODULE_PARM_DESC(disable_msi, "Disable M
 static DEFINE_PCI_DEVICE_TABLE(sky2_id_table) = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) }, /* SK-9Sxx */
 	{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, /* SK-9Exx */
+	{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E01) }, /* SK-9E21M */
 	{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b00) },	/* DGE-560T */
 	{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4001) }, 	/* DGE-550SX */
 	{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4B02) },	/* DGE-560SX */

-- 

[PATCH 2/6] sky2: add register definitions for new chips

[Stephen Hemminger]

[-- Attachment #1: sky2-reg-update.patch --]
[-- Type: text/plain, Size: 11754 bytes --]

This adds infrastructure for the newer chip versions and workarounds.
Extracted from the vendor (GPL) driver.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>

--- a/drivers/net/sky2.h	2009-10-29 08:34:51.778438561 -0700
+++ b/drivers/net/sky2.h	2009-10-29 08:35:53.313438448 -0700
@@ -16,6 +16,13 @@ enum {
 	PCI_DEV_REG5    = 0x88,
 	PCI_CFG_REG_0	= 0x90,
 	PCI_CFG_REG_1	= 0x94,
+
+	PSM_CONFIG_REG0  = 0x98,
+	PSM_CONFIG_REG1	 = 0x9C,
+	PSM_CONFIG_REG2  = 0x160,
+	PSM_CONFIG_REG3  = 0x164,
+	PSM_CONFIG_REG4  = 0x168,
+
 };
 
 /* Yukon-2 */
@@ -48,6 +55,37 @@ enum pci_dev_reg_2 {
 	PCI_USEDATA64	= 1<<0,		/* Use 64Bit Data bus ext */
 };
 
+/*	PCI_OUR_REG_3		32 bit	Our Register 3 (Yukon-ECU only) */
+enum pci_dev_reg_3 {
+	P_CLK_ASF_REGS_DIS	= 1<<18,/* Disable Clock ASF (Yukon-Ext.) */
+	P_CLK_COR_REGS_D0_DIS	= 1<<17,/* Disable Clock Core Regs D0 */
+	P_CLK_MACSEC_DIS	= 1<<17,/* Disable Clock MACSec (Yukon-Ext.) */
+	P_CLK_PCI_REGS_D0_DIS	= 1<<16,/* Disable Clock PCI  Regs D0 */
+	P_CLK_COR_YTB_ARB_DIS	= 1<<15,/* Disable Clock YTB  Arbiter */
+	P_CLK_MAC_LNK1_D3_DIS	= 1<<14,/* Disable Clock MAC  Link1 D3 */
+	P_CLK_COR_LNK1_D0_DIS	= 1<<13,/* Disable Clock Core Link1 D0 */
+	P_CLK_MAC_LNK1_D0_DIS	= 1<<12,/* Disable Clock MAC  Link1 D0 */
+	P_CLK_COR_LNK1_D3_DIS	= 1<<11,/* Disable Clock Core Link1 D3 */
+	P_CLK_PCI_MST_ARB_DIS	= 1<<10,/* Disable Clock PCI  Master Arb. */
+	P_CLK_COR_REGS_D3_DIS	= 1<<9,	/* Disable Clock Core Regs D3 */
+	P_CLK_PCI_REGS_D3_DIS	= 1<<8,	/* Disable Clock PCI  Regs D3 */
+	P_CLK_REF_LNK1_GM_DIS	= 1<<7,	/* Disable Clock Ref. Link1 GMAC */
+	P_CLK_COR_LNK1_GM_DIS	= 1<<6,	/* Disable Clock Core Link1 GMAC */
+	P_CLK_PCI_COMMON_DIS	= 1<<5,	/* Disable Clock PCI  Common */
+	P_CLK_COR_COMMON_DIS	= 1<<4,	/* Disable Clock Core Common */
+	P_CLK_PCI_LNK1_BMU_DIS	= 1<<3,	/* Disable Clock PCI  Link1 BMU */
+	P_CLK_COR_LNK1_BMU_DIS	= 1<<2,	/* Disable Clock Core Link1 BMU */
+	P_CLK_PCI_LNK1_BIU_DIS	= 1<<1,	/* Disable Clock PCI  Link1 BIU */
+	P_CLK_COR_LNK1_BIU_DIS	= 1<<0,	/* Disable Clock Core Link1 BIU */
+	PCIE_OUR3_WOL_D3_COLD_SET = P_CLK_ASF_REGS_DIS |
+				    P_CLK_COR_REGS_D0_DIS |
+				    P_CLK_COR_LNK1_D0_DIS |
+				    P_CLK_MAC_LNK1_D0_DIS |
+				    P_CLK_PCI_MST_ARB_DIS |
+				    P_CLK_COR_COMMON_DIS |
+				    P_CLK_COR_LNK1_BMU_DIS,
+};
+
 /*	PCI_OUR_REG_4		32 bit	Our Register 4 (Yukon-ECU only) */
 enum pci_dev_reg_4 {
 				/* (Link Training & Status State Machine) */
@@ -114,7 +152,7 @@ enum pci_dev_reg_5 {
 				     P_GAT_PCIE_RX_EL_IDLE,
 };
 
-#/*	PCI_CFG_REG_1			32 bit	Config Register 1 (Yukon-Ext only) */
+/*	PCI_CFG_REG_1			32 bit	Config Register 1 (Yukon-Ext only) */
 enum pci_cfg_reg1 {
 	P_CF1_DIS_REL_EVT_RST	= 1<<24, /* Dis. Rel. Event during PCIE reset */
 										/* Bit 23..21: Release Clock on Event */
@@ -145,6 +183,72 @@ enum pci_cfg_reg1 {
 					P_CF1_ENA_TXBMU_WR_IDLE,
 };
 
+/* Yukon-Optima */
+enum {
+	PSM_CONFIG_REG1_AC_PRESENT_STATUS = 1<<31,   /* AC Present Status */
+
+	PSM_CONFIG_REG1_PTP_CLK_SEL	  = 1<<29,   /* PTP Clock Select */
+	PSM_CONFIG_REG1_PTP_MODE	  = 1<<28,   /* PTP Mode */
+
+	PSM_CONFIG_REG1_MUX_PHY_LINK	  = 1<<27,   /* PHY Energy Detect Event */
+
+	PSM_CONFIG_REG1_EN_PIN63_AC_PRESENT = 1<<26,  /* Enable LED_DUPLEX for ac_present */
+	PSM_CONFIG_REG1_EN_PCIE_TIMER	  = 1<<25,    /* Enable PCIe Timer */
+	PSM_CONFIG_REG1_EN_SPU_TIMER	  = 1<<24,    /* Enable SPU Timer */
+	PSM_CONFIG_REG1_POLARITY_AC_PRESENT = 1<<23,  /* AC Present Polarity */
+
+	PSM_CONFIG_REG1_EN_AC_PRESENT	  = 1<<21,    /* Enable AC Present */
+
+	PSM_CONFIG_REG1_EN_GPHY_INT_PSM	= 1<<20,      /* Enable GPHY INT for PSM */
+	PSM_CONFIG_REG1_DIS_PSM_TIMER	= 1<<19,      /* Disable PSM Timer */
+};
+
+/* Yukon-Supreme */
+enum {
+	PSM_CONFIG_REG1_GPHY_ENERGY_STS	= 1<<31, /* GPHY Energy Detect Status */
+
+	PSM_CONFIG_REG1_UART_MODE_MSK	= 3<<29, /* UART_Mode */
+	PSM_CONFIG_REG1_CLK_RUN_ASF	= 1<<28, /* Enable Clock Free Running for ASF Subsystem */
+	PSM_CONFIG_REG1_UART_CLK_DISABLE= 1<<27, /* Disable UART clock */
+	PSM_CONFIG_REG1_VAUX_ONE	= 1<<26, /* Tie internal Vaux to 1'b1 */
+	PSM_CONFIG_REG1_UART_FC_RI_VAL	= 1<<25, /* Default value for UART_RI_n */
+	PSM_CONFIG_REG1_UART_FC_DCD_VAL	= 1<<24, /* Default value for UART_DCD_n */
+	PSM_CONFIG_REG1_UART_FC_DSR_VAL	= 1<<23, /* Default value for UART_DSR_n */
+	PSM_CONFIG_REG1_UART_FC_CTS_VAL	= 1<<22, /* Default value for UART_CTS_n */
+	PSM_CONFIG_REG1_LATCH_VAUX	= 1<<21, /* Enable Latch current Vaux_avlbl */
+	PSM_CONFIG_REG1_FORCE_TESTMODE_INPUT= 1<<20, /* Force Testmode pin as input PAD */
+	PSM_CONFIG_REG1_UART_RST	= 1<<19, /* UART_RST */
+	PSM_CONFIG_REG1_PSM_PCIE_L1_POL	= 1<<18, /* PCIE L1 Event Polarity for PSM */
+	PSM_CONFIG_REG1_TIMER_STAT	= 1<<17, /* PSM Timer Status */
+	PSM_CONFIG_REG1_GPHY_INT	= 1<<16, /* GPHY INT Status */
+	PSM_CONFIG_REG1_FORCE_TESTMODE_ZERO= 1<<15, /* Force internal Testmode as 1'b0 */
+	PSM_CONFIG_REG1_EN_INT_ASPM_CLKREQ = 1<<14, /* ENABLE INT for CLKRUN on ASPM and CLKREQ */
+	PSM_CONFIG_REG1_EN_SND_TASK_ASPM_CLKREQ	= 1<<13, /* ENABLE Snd_task for CLKRUN on ASPM and CLKREQ */
+	PSM_CONFIG_REG1_DIS_CLK_GATE_SND_TASK	= 1<<12, /* Disable CLK_GATE control snd_task */
+	PSM_CONFIG_REG1_DIS_FF_CHIAN_SND_INTA	= 1<<11, /* Disable flip-flop chain for sndmsg_inta */
+
+	PSM_CONFIG_REG1_DIS_LOADER	= 1<<9, /* Disable Loader SM after PSM Goes back to IDLE */
+	PSM_CONFIG_REG1_DO_PWDN		= 1<<8, /* Do Power Down, Start PSM Scheme */
+	PSM_CONFIG_REG1_DIS_PIG		= 1<<7, /* Disable Plug-in-Go SM after PSM Goes back to IDLE */
+	PSM_CONFIG_REG1_DIS_PERST	= 1<<6, /* Disable Internal PCIe Reset after PSM Goes back to IDLE */
+	PSM_CONFIG_REG1_EN_REG18_PD	= 1<<5, /* Enable REG18 Power Down for PSM */
+	PSM_CONFIG_REG1_EN_PSM_LOAD	= 1<<4, /* Disable EEPROM Loader after PSM Goes back to IDLE */
+	PSM_CONFIG_REG1_EN_PSM_HOT_RST	= 1<<3, /* Enable PCIe Hot Reset for PSM */
+	PSM_CONFIG_REG1_EN_PSM_PERST	= 1<<2, /* Enable PCIe Reset Event for PSM */
+	PSM_CONFIG_REG1_EN_PSM_PCIE_L1	= 1<<1, /* Enable PCIe L1 Event for PSM */
+	PSM_CONFIG_REG1_EN_PSM		= 1<<0, /* Enable PSM Scheme */
+};
+
+/*	PSM_CONFIG_REG4				0x0168	PSM Config Register 4 */
+enum {
+						/* PHY Link Detect Timer */
+	PSM_CONFIG_REG4_TIMER_PHY_LINK_DETECT_MSK = 0xf<<4,
+	PSM_CONFIG_REG4_TIMER_PHY_LINK_DETECT_BASE = 4,
+
+	PSM_CONFIG_REG4_DEBUG_TIMER	    = 1<<1, /* Debug Timer */
+	PSM_CONFIG_REG4_RST_PHY_LINK_DETECT = 1<<0, /* Reset GPHY Link Detect */
+};
+
 
 #define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
 			       PCI_STATUS_SIG_SYSTEM_ERROR | \
@@ -197,6 +301,9 @@ enum csr_regs {
 	B2_I2C_IRQ	= 0x0168,
 	B2_I2C_SW	= 0x016c,
 
+	Y2_PEX_PHY_DATA = 0x0170,
+	Y2_PEX_PHY_ADDR = 0x0172,
+
 	B3_RAM_ADDR	= 0x0180,
 	B3_RAM_DATA_LO	= 0x0184,
 	B3_RAM_DATA_HI	= 0x0188,
@@ -317,6 +424,10 @@ enum {
 	Y2_IS_CHK_TXS2	= 1<<9,		/* Descriptor error TXS 2 */
 	Y2_IS_CHK_TXA2	= 1<<8,		/* Descriptor error TXA 2 */
 
+	Y2_IS_PSM_ACK	= 1<<7,		/* PSM Acknowledge (Yukon-Optima only) */
+	Y2_IS_PTP_TIST	= 1<<6,		/* PTP Time Stamp (Yukon-Optima only) */
+	Y2_IS_PHY_QLNK	= 1<<5,		/* PHY Quick Link (Yukon-Optima only) */
+
 	Y2_IS_IRQ_PHY1	= 1<<4,		/* Interrupt from PHY 1 */
 	Y2_IS_IRQ_MAC1	= 1<<3,		/* Interrupt from MAC 1 */
 	Y2_IS_CHK_RX1	= 1<<2,		/* Descriptor error Rx 1 */
@@ -435,6 +546,7 @@ enum {
  	CHIP_ID_YUKON_FE_P = 0xb8, /* YUKON-2 FE+ */
 	CHIP_ID_YUKON_SUPR = 0xb9, /* YUKON-2 Supreme */
 	CHIP_ID_YUKON_UL_2 = 0xba, /* YUKON-2 Ultra 2 */
+	CHIP_ID_YUKON_OPT  = 0xbc, /* YUKON-2 Optima */
 };
 enum yukon_ec_rev {
 	CHIP_REV_YU_EC_A1    = 0,  /* Chip Rev. for Yukon-EC A1/A0 */
@@ -459,6 +571,8 @@ enum yukon_ex_rev {
 };
 enum yukon_supr_rev {
 	CHIP_REV_YU_SU_A0    = 0,
+	CHIP_REV_YU_SU_B0    = 1,
+	CHIP_REV_YU_SU_B1    = 3,
 };
 
 
@@ -513,6 +627,12 @@ enum {
 	TIM_T_STEP	= 1<<0,	/* Test step */
 };
 
+/*	Y2_PEX_PHY_ADDR/DATA		PEX PHY address and data reg  (Yukon-2 only) */
+enum {
+	PEX_RD_ACCESS	= 1<<31, /* Access Mode Read = 1, Write = 0 */
+	PEX_DB_ACCESS	= 1<<30, /* Access to debug register */
+};
+
 /*	B3_RAM_ADDR		32 bit	RAM Address, to read or write */
 					/* Bit 31..19:	reserved */
 #define RAM_ADR_RAN	0x0007ffffL	/* Bit 18.. 0:	RAM Address Range */
@@ -754,6 +874,42 @@ enum {
 	BMU_TX_CLR_IRQ_TCP	= 1<<11, /* Clear IRQ on TCP segment length mismatch */
 };
 
+/*	TBMU_TEST			0x06B8	Transmit BMU Test Register */
+enum {
+	TBMU_TEST_BMU_TX_CHK_AUTO_OFF		= 1<<31, /* BMU Tx Checksum Auto Calculation Disable */
+	TBMU_TEST_BMU_TX_CHK_AUTO_ON		= 1<<30, /* BMU Tx Checksum Auto Calculation Enable */
+	TBMU_TEST_HOME_ADD_PAD_FIX1_EN		= 1<<29, /* Home Address Paddiing FIX1 Enable */
+	TBMU_TEST_HOME_ADD_PAD_FIX1_DIS		= 1<<28, /* Home Address Paddiing FIX1 Disable */
+	TBMU_TEST_ROUTING_ADD_FIX_EN		= 1<<27, /* Routing Address Fix Enable */
+	TBMU_TEST_ROUTING_ADD_FIX_DIS		= 1<<26, /* Routing Address Fix Disable */
+	TBMU_TEST_HOME_ADD_FIX_EN		= 1<<25, /* Home address checksum fix enable */
+	TBMU_TEST_HOME_ADD_FIX_DIS		= 1<<24, /* Home address checksum fix disable */
+
+	TBMU_TEST_TEST_RSPTR_ON			= 1<<22, /* Testmode Shadow Read Ptr On */
+	TBMU_TEST_TEST_RSPTR_OFF		= 1<<21, /* Testmode Shadow Read Ptr Off */
+	TBMU_TEST_TESTSTEP_RSPTR		= 1<<20, /* Teststep Shadow Read Ptr */
+
+	TBMU_TEST_TEST_RPTR_ON			= 1<<18, /* Testmode Read Ptr On */
+	TBMU_TEST_TEST_RPTR_OFF			= 1<<17, /* Testmode Read Ptr Off */
+	TBMU_TEST_TESTSTEP_RPTR			= 1<<16, /* Teststep Read Ptr */
+
+	TBMU_TEST_TEST_WSPTR_ON			= 1<<14, /* Testmode Shadow Write Ptr On */
+	TBMU_TEST_TEST_WSPTR_OFF		= 1<<13, /* Testmode Shadow Write Ptr Off */
+	TBMU_TEST_TESTSTEP_WSPTR		= 1<<12, /* Teststep Shadow Write Ptr */
+
+	TBMU_TEST_TEST_WPTR_ON			= 1<<10, /* Testmode Write Ptr On */
+	TBMU_TEST_TEST_WPTR_OFF			= 1<<9, /* Testmode Write Ptr Off */
+	TBMU_TEST_TESTSTEP_WPTR			= 1<<8,			/* Teststep Write Ptr */
+
+	TBMU_TEST_TEST_REQ_NB_ON		= 1<<6, /* Testmode Req Nbytes/Addr On */
+	TBMU_TEST_TEST_REQ_NB_OFF		= 1<<5, /* Testmode Req Nbytes/Addr Off */
+	TBMU_TEST_TESTSTEP_REQ_NB		= 1<<4, /* Teststep Req Nbytes/Addr */
+
+	TBMU_TEST_TEST_DONE_IDX_ON		= 1<<2, /* Testmode Done Index On */
+	TBMU_TEST_TEST_DONE_IDX_OFF		= 1<<1, /* Testmode Done Index Off */
+	TBMU_TEST_TESTSTEP_DONE_IDX		= 1<<0,	/* Teststep Done Index */
+};
+
 /* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
 /* PREF_UNIT_CTRL	32 bit	Prefetch Control register */
 enum {
@@ -1674,6 +1830,12 @@ enum {
 
 /*	RX_GMF_CTRL_T	32 bit	Rx GMAC FIFO Control/Test */
 enum {
+	RX_GCLKMAC_ENA	= 1<<31,	/* RX MAC Clock Gating Enable */
+	RX_GCLKMAC_OFF	= 1<<30,
+
+	RX_STFW_DIS	= 1<<29,	/* RX Store and Forward Enable */
+	RX_STFW_ENA	= 1<<28,
+
 	RX_TRUNC_ON	= 1<<27,  	/* enable  packet truncation */
 	RX_TRUNC_OFF	= 1<<26, 	/* disable packet truncation */
 	RX_VLAN_STRIP_ON = 1<<25,	/* enable  VLAN stripping */
@@ -1711,6 +1873,20 @@ enum {
 	GMF_RX_CTRL_DEF	= GMF_OPER_ON | GMF_RX_F_FL_ON,
 };
 
+/*	RX_GMF_FL_CTRL	16 bit	Rx GMAC FIFO Flush Control (Yukon-Supreme) */
+enum {
+	RX_IPV6_SA_MOB_ENA	= 1<<9,	/* IPv6 SA Mobility Support Enable */
+	RX_IPV6_SA_MOB_DIS	= 1<<8,	/* IPv6 SA Mobility Support Disable */
+	RX_IPV6_DA_MOB_ENA	= 1<<7,	/* IPv6 DA Mobility Support Enable */
+	RX_IPV6_DA_MOB_DIS	= 1<<6,	/* IPv6 DA Mobility Support Disable */
+	RX_PTR_SYNCDLY_ENA	= 1<<5,	/* Pointers Delay Synch Enable */
+	RX_PTR_SYNCDLY_DIS	= 1<<4,	/* Pointers Delay Synch Disable */
+	RX_ASF_NEWFLAG_ENA	= 1<<3,	/* RX ASF Flag New Logic Enable */
+	RX_ASF_NEWFLAG_DIS	= 1<<2,	/* RX ASF Flag New Logic Disable */
+	RX_FLSH_MISSPKT_ENA	= 1<<1,	/* RX Flush Miss-Packet Enable */
+	RX_FLSH_MISSPKT_DIS	= 1<<0,	/* RX Flush Miss-Packet Disable */
+};
+
 /*	TX_GMF_EA		32 bit	Tx GMAC FIFO End Address */
 enum {
 	TX_DYN_WM_ENA	= 3,	/* Yukon-FE+ specific */

-- 

[PATCH 3/6] sky2: fix receive pause thresholds

[Stephen Hemminger]

[-- Attachment #1: sky2-rxthresh.patch --]
[-- Type: text/plain, Size: 1964 bytes --]

Program the receive pause thresholds differently depending on
chip version. This cloned from from the vendor (GPL) driver.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>


--- a/drivers/net/sky2.h	2009-10-29 08:35:53.313438448 -0700
+++ b/drivers/net/sky2.h	2009-10-29 08:37:04.959438572 -0700
@@ -808,10 +808,11 @@ enum {
 	RX_GMF_AF_THR	= 0x0c44,/* 32 bit	Rx GMAC FIFO Almost Full Thresh. */
 	RX_GMF_CTRL_T	= 0x0c48,/* 32 bit	Rx GMAC FIFO Control/Test */
 	RX_GMF_FL_MSK	= 0x0c4c,/* 32 bit	Rx GMAC FIFO Flush Mask */
-	RX_GMF_FL_THR	= 0x0c50,/* 32 bit	Rx GMAC FIFO Flush Threshold */
+	RX_GMF_FL_THR	= 0x0c50,/* 16 bit	Rx GMAC FIFO Flush Threshold */
+	RX_GMF_FL_CTRL	= 0x0c52,/* 16 bit	Rx GMAC FIFO Flush Control */
 	RX_GMF_TR_THR	= 0x0c54,/* 32 bit	Rx Truncation Threshold (Yukon-2) */
-	RX_GMF_UP_THR	= 0x0c58,/*  8 bit	Rx Upper Pause Thr (Yukon-EC_U) */
-	RX_GMF_LP_THR	= 0x0c5a,/*  8 bit	Rx Lower Pause Thr (Yukon-EC_U) */
+	RX_GMF_UP_THR	= 0x0c58,/* 16 bit	Rx Upper Pause Thr (Yukon-EC_U) */
+	RX_GMF_LP_THR	= 0x0c5a,/* 16 bit	Rx Lower Pause Thr (Yukon-EC_U) */
 	RX_GMF_VLAN	= 0x0c5c,/* 32 bit	Rx VLAN Type Register (Yukon-2) */
 	RX_GMF_WP	= 0x0c60,/* 32 bit	Rx GMAC FIFO Write Pointer */
 
--- a/drivers/net/sky2.c	2009-10-29 08:34:04.765191254 -0700
+++ b/drivers/net/sky2.c	2009-10-29 08:52:37.995315808 -0700
@@ -926,8 +926,14 @@ static void sky2_mac_init(struct sky2_hw
 
 	/* On chips without ram buffer, pause is controled by MAC level */
 	if (!(hw->flags & SKY2_HW_RAM_BUFFER)) {
-		sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8);
-		sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8);
+		/* Pause threshold is scaled by 8 in bytes */
+		if (hw->chip_id == CHIP_ID_YUKON_FE_P
+			&& hw->chip_rev == CHIP_REV_YU_FE2_A0)
+			reg = 1568 / 8;
+		else
+			reg = 1024 / 8;
+		sky2_write16(hw, SK_REG(port, RX_GMF_UP_THR), reg);
+		sky2_write16(hw, SK_REG(port, RX_GMF_LP_THR), 768 / 8);
 
 		sky2_set_tx_stfwd(hw, port);
 	}

-- 

[PATCH 4/6] sky2: workarounds for Yukon-2 supreme

[Stephen Hemminger]

[-- Attachment #1: sky2-supr2.patch --]
[-- Type: text/plain, Size: 2178 bytes --]

Changes related to support of Yukon supreme chip.
Don't have this chip version to test on,
these are reverse engineered from the vendor (GPL) driver.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>


--- a/drivers/net/sky2.c	2009-10-29 08:52:37.995315808 -0700
+++ b/drivers/net/sky2.c	2009-10-29 08:55:47.116003224 -0700
@@ -787,8 +787,7 @@ static void sky2_set_tx_stfwd(struct sky
 
 	if ( (hw->chip_id == CHIP_ID_YUKON_EX &&
 	      hw->chip_rev != CHIP_REV_YU_EX_A0) ||
-	     hw->chip_id == CHIP_ID_YUKON_FE_P ||
-	     hw->chip_id == CHIP_ID_YUKON_SUPR) {
+	     hw->chip_id >= CHIP_ID_YUKON_FE_P) {
 		/* Yukon-Extreme B0 and further Extreme devices */
 		/* enable Store & Forward mode for TX */
 
@@ -1404,6 +1403,31 @@ static int sky2_rx_start(struct sky2_por
 
 	/* Tell chip about available buffers */
 	sky2_rx_update(sky2, rxq);
+
+	if (hw->chip_id == CHIP_ID_YUKON_EX ||
+	    hw->chip_id == CHIP_ID_YUKON_SUPR) {
+		/*
+		 * Disable flushing of non ASF packets;
+		 * must be done after initializing the BMUs;
+		 * drivers without ASF support should do this too, otherwise
+		 * it may happen that they cannot run on ASF devices;
+		 * remember that the MAC FIFO isn't reset during initialization.
+		 */
+		sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_MACSEC_FLUSH_OFF);
+	}
+
+	if (hw->chip_id >= CHIP_ID_YUKON_SUPR) {
+		/* Enable RX Home Address & Routing Header checksum fix */
+		sky2_write16(hw, SK_REG(sky2->port, RX_GMF_FL_CTRL),
+			     RX_IPV6_SA_MOB_ENA | RX_IPV6_DA_MOB_ENA);
+
+		/* Enable TX Home Address & Routing Header checksum fix */
+		sky2_write32(hw, Q_ADDR(txqaddr[sky2->port], Q_TEST),
+			     TBMU_TEST_HOME_ADD_FIX_EN | TBMU_TEST_ROUTING_ADD_FIX_EN);
+	}
+
+
+
 	return 0;
 nomem:
 	sky2_rx_clean(sky2);
@@ -2993,6 +3017,12 @@ static void sky2_reset(struct sky2_hw *h
 			sky2_write16(hw, SK_REG(i, GMAC_CTRL),
 				     GMC_BYP_MACSECRX_ON | GMC_BYP_MACSECTX_ON
 				     | GMC_BYP_RETR_ON);
+
+	}
+
+	if (hw->chip_id == CHIP_ID_YUKON_SUPR && hw->chip_rev > CHIP_REV_YU_SU_B0) {
+		/* enable MACSec clock gating */
+		sky2_pci_write32(hw, PCI_DEV_REG3, P_CLK_MACSEC_DIS);
 	}
 
 	/* Clear I2C IRQ noise */

-- 

[PATCH 5/6] sky2: 88E8059 support

[Stephen Hemminger]

[-- Attachment #1: sky2-yukon-ul_2.patch --]
[-- Type: text/plain, Size: 4547 bytes --]

Tentative support for newer Marvell hardware including
the Yukon-2 Optima chip. Do not have hatdware to test this yet,
code is based on vendor driver.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>

--- a/drivers/net/sky2.c	2009-10-28 11:02:38.031251525 -0700
+++ b/drivers/net/sky2.c	2009-10-28 11:02:44.719000693 -0700
@@ -140,6 +140,7 @@ static DEFINE_PCI_DEVICE_TABLE(sky2_id_t
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436D) }, /* 88E8055 */
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4370) }, /* 88E8075 */
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4380) }, /* 88E8057 */
+	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4381) }, /* 88E8059 */
 	{ 0 }
 };
 
@@ -603,6 +604,16 @@ static void sky2_phy_init(struct sky2_hw
 		/* apply workaround for integrated resistors calibration */
 		gm_phy_write(hw, port, PHY_MARV_PAGE_ADDR, 17);
 		gm_phy_write(hw, port, PHY_MARV_PAGE_DATA, 0x3f60);
+	} else if (hw->chip_id == CHIP_ID_YUKON_OPT && hw->chip_rev == 0) {
+		/* apply fixes in PHY AFE */
+		gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0x00ff);
+
+		/* apply RDAC termination workaround */
+		gm_phy_write(hw, port, 24, 0x2800);
+		gm_phy_write(hw, port, 23, 0x2001);
+
+		/* set page register back to 0 */
+		gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0);
 	} else if (hw->chip_id != CHIP_ID_YUKON_EX &&
 		   hw->chip_id < CHIP_ID_YUKON_SUPR) {
 		/* no effect on Yukon-XL */
@@ -2133,6 +2144,25 @@ out:
 	spin_unlock(&sky2->phy_lock);
 }
 
+/* Special quick link interrupt (Yukon-2 Optima only) */
+static void sky2_qlink_intr(struct sky2_hw *hw)
+{
+	struct sky2_port *sky2 = netdev_priv(hw->dev[0]);
+	u32 imask;
+	u16 phy;
+
+	/* disable irq */
+	imask = sky2_read32(hw, B0_IMSK);
+	imask &= ~Y2_IS_PHY_QLNK;
+	sky2_write32(hw, B0_IMSK, imask);
+
+	/* reset PHY Link Detect */
+	phy = sky2_pci_read16(hw, PSM_CONFIG_REG4);
+	sky2_pci_write16(hw, PSM_CONFIG_REG4, phy | 1);
+
+	sky2_link_up(sky2);
+}
+
 /* Transmit timeout is only called if we are running, carrier is up
  * and tx queue is full (stopped).
  */
@@ -2803,6 +2833,9 @@ static int sky2_poll(struct napi_struct 
 	if (status & Y2_IS_IRQ_PHY2)
 		sky2_phy_intr(hw, 1);
 
+	if (status & Y2_IS_PHY_QLNK)
+		sky2_qlink_intr(hw);
+
 	while ((idx = sky2_read16(hw, STAT_PUT_IDX)) != hw->st_idx) {
 		work_done += sky2_status_intr(hw, work_limit - work_done, idx);
 
@@ -2852,6 +2885,7 @@ static u32 sky2_mhz(const struct sky2_hw
 	case CHIP_ID_YUKON_EX:
 	case CHIP_ID_YUKON_SUPR:
 	case CHIP_ID_YUKON_UL_2:
+	case CHIP_ID_YUKON_OPT:
 		return 125;
 
 	case CHIP_ID_YUKON_FE:
@@ -2941,6 +2975,7 @@ static int __devinit sky2_init(struct sk
 		break;
 
 	case CHIP_ID_YUKON_UL_2:
+	case CHIP_ID_YUKON_OPT:
 		hw->flags = SKY2_HW_GIGABIT
 			| SKY2_HW_ADV_POWER_CTL;
 		break;
@@ -3031,6 +3066,46 @@ static void sky2_reset(struct sky2_hw *h
 		sky2_pci_write32(hw, PCI_DEV_REG3, P_CLK_MACSEC_DIS);
 	}
 
+	if (hw->chip_id == CHIP_ID_YUKON_OPT) {
+		u16 reg;
+		u32 msk;
+
+		if (hw->chip_rev == 0) {
+			/* disable PCI-E PHY power down (set PHY reg 0x80, bit 7 */
+			sky2_write32(hw, Y2_PEX_PHY_DATA, (0x80UL << 16) | (1 << 7));
+
+			/* set PHY Link Detect Timer to 1.1 second (11x 100ms) */
+			reg = 10;
+		} else {
+			/* set PHY Link Detect Timer to 0.4 second (4x 100ms) */
+			reg = 3;
+		}
+
+		reg <<= PSM_CONFIG_REG4_TIMER_PHY_LINK_DETECT_BASE;
+
+		/* reset PHY Link Detect */
+		sky2_pci_write16(hw, PSM_CONFIG_REG4,
+				 reg | PSM_CONFIG_REG4_RST_PHY_LINK_DETECT);
+		sky2_pci_write16(hw, PSM_CONFIG_REG4, reg);
+
+
+		/* enable PHY Quick Link */
+		msk = sky2_read32(hw, B0_IMSK);
+		msk |= Y2_IS_PHY_QLNK;
+		sky2_write32(hw, B0_IMSK, msk);
+
+		/* check if PSMv2 was running before */
+		reg = sky2_pci_read16(hw, PSM_CONFIG_REG3);
+		if (reg & PCI_EXP_LNKCTL_ASPMC) {
+			int cap = pci_find_capability(pdev, PCI_CAP_ID_EXP);
+			/* restore the PCIe Link Control register */
+			sky2_pci_write16(hw, cap + PCI_EXP_LNKCTL, reg);
+		}
+
+		/* re-enable PEX PM in PEX PHY debug reg. 8 (clear bit 12) */
+		sky2_write32(hw, Y2_PEX_PHY_DATA, PEX_DB_ACCESS | (0x08UL << 16));
+	}
+
 	/* Clear I2C IRQ noise */
 	sky2_write32(hw, B2_I2C_IRQ, 1);
 
@@ -4451,9 +4526,11 @@ static const char *sky2_name(u8 chipid, 
 		"FE+",		/* 0xb8 */
 		"Supreme",	/* 0xb9 */
 		"UL 2",		/* 0xba */
+		"Unknown",	/* 0xbb */
+		"Optima",	/* 0xbc */
 	};
 
-	if (chipid >= CHIP_ID_YUKON_XL && chipid < CHIP_ID_YUKON_UL_2)
+	if (chipid >= CHIP_ID_YUKON_XL && chipid < CHIP_ID_YUKON_OPT)
 		strncpy(buf, name[chipid - CHIP_ID_YUKON_XL], sz);
 	else
 		snprintf(buf, sz, "(chip %#x)", chipid);

-- 

[PATCH 6/6] sky2: version 1.26

[Stephen Hemminger]

[-- Attachment #1: sky2-1.26.patch --]
[-- Type: text/plain, Size: 343 bytes --]

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>

--- a/drivers/net/sky2.c	2009-10-29 08:57:43.512001253 -0700
+++ b/drivers/net/sky2.c	2009-10-29 08:59:34.782375629 -0700
@@ -50,7 +50,7 @@
 #include "sky2.h"
 
 #define DRV_NAME		"sky2"
-#define DRV_VERSION		"1.25"
+#define DRV_VERSION		"1.26"
 #define PFX			DRV_NAME " "
 
 /*

-- 

Re: [PATCH 0/6] sky2: driver update

[David Miller]

From: Stephen Hemminger <shemminger@vyatta.com>
Date: Thu, 29 Oct 2009 09:37:04 -0700

> This patch set adds support for Yukon Optima (88E8059) based
> on the vendor driver.  Hopefully, it can go in 2.6.32.

Sorry, this is too much too late.  You don't even have the hardware
to test the changes you are making to the driver which makes this
even more questionable for net-2.6

I'll toss this into net-next-2.6 and let's let it cook there for
a while at least.

If you want to pick out a small bug fix or two from this series
for net-2.6, please feel free to resubmit them specifically for
net-2.6 inclusion.

Thanks.