* [net-next-2.6 PATCH 1/3] igb: add support for the 82580 phy
@ 2009-11-19 22:41 Jeff Kirsher
2009-11-19 22:42 ` [net-next-2.6 PATCH 2/3] igb: add support for 82580 MAC Jeff Kirsher
` (2 more replies)
0 siblings, 3 replies; 5+ messages in thread
From: Jeff Kirsher @ 2009-11-19 22:41 UTC (permalink / raw)
To: davem; +Cc: netdev, gospo, Alexander Duyck, Jeff Kirsher
From: Alexander Duyck <alexander.h.duyck@intel.com>
This patch adds support for the phy included in the 82580 silicon family.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/igb/e1000_hw.h | 1
drivers/net/igb/e1000_phy.c | 242 +++++++++++++++++++++++++++++++++++++++++++
drivers/net/igb/e1000_phy.h | 32 ++++++
3 files changed, 275 insertions(+), 0 deletions(-)
diff --git a/drivers/net/igb/e1000_hw.h b/drivers/net/igb/e1000_hw.h
index 2dc9294..5deda3e 100644
--- a/drivers/net/igb/e1000_hw.h
+++ b/drivers/net/igb/e1000_hw.h
@@ -93,6 +93,7 @@ enum e1000_phy_type {
e1000_phy_gg82563,
e1000_phy_igp_3,
e1000_phy_ife,
+ e1000_phy_82580,
};
enum e1000_bus_type {
diff --git a/drivers/net/igb/e1000_phy.c b/drivers/net/igb/e1000_phy.c
index 83b706c..b8fbc85 100644
--- a/drivers/net/igb/e1000_phy.c
+++ b/drivers/net/igb/e1000_phy.c
@@ -421,6 +421,57 @@ out:
}
/**
+ * igb_copper_link_setup_82580 - Setup 82580 PHY for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Sets up Carrier-sense on Transmit and downshift values.
+ **/
+s32 igb_copper_link_setup_82580(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+
+
+ if (phy->reset_disable) {
+ ret_val = 0;
+ goto out;
+ }
+
+ if (phy->type == e1000_phy_82580) {
+ ret_val = hw->phy.ops.reset(hw);
+ if (ret_val) {
+ hw_dbg("Error resetting the PHY.\n");
+ goto out;
+ }
+ }
+
+ /* Enable CRS on TX. This must be set for half-duplex operation. */
+ ret_val = phy->ops.read_reg(hw, I82580_CFG_REG, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data |= I82580_CFG_ASSERT_CRS_ON_TX;
+
+ /* Enable downshift */
+ phy_data |= I82580_CFG_ENABLE_DOWNSHIFT;
+
+ ret_val = phy->ops.write_reg(hw, I82580_CFG_REG, phy_data);
+ if (ret_val)
+ goto out;
+
+ /* Set number of link attempts before downshift */
+ ret_val = phy->ops.read_reg(hw, I82580_CTRL_REG, &phy_data);
+ if (ret_val)
+ goto out;
+ phy_data &= ~I82580_CTRL_DOWNSHIFT_MASK;
+ ret_val = phy->ops.write_reg(hw, I82580_CTRL_REG, phy_data);
+
+out:
+ return ret_val;
+}
+
+/**
* igb_copper_link_setup_m88 - Setup m88 PHY's for copper link
* @hw: pointer to the HW structure
*
@@ -1888,3 +1939,194 @@ s32 igb_phy_init_script_igp3(struct e1000_hw *hw)
return 0;
}
+/**
+ * igb_check_polarity_82580 - Checks the polarity.
+ * @hw: pointer to the HW structure
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ *
+ * Polarity is determined based on the PHY specific status register.
+ **/
+s32 igb_check_polarity_82580(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+
+
+ ret_val = phy->ops.read_reg(hw, I82580_PHY_STATUS_2, &data);
+
+ if (!ret_val)
+ phy->cable_polarity = (data & I82580_PHY_STATUS2_REV_POLARITY)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+
+ return ret_val;
+}
+
+/**
+ * igb_phy_force_speed_duplex_82580 - Force speed/duplex for I82580 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Calls the PHY setup function to force speed and duplex. Clears the
+ * auto-crossover to force MDI manually. Waits for link and returns
+ * successful if link up is successful, else -E1000_ERR_PHY (-2).
+ **/
+s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+
+ ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ igb_phy_force_speed_duplex_setup(hw, &phy_data);
+
+ ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_data);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Clear Auto-Crossover to force MDI manually. 82580 requires MDI
+ * forced whenever speed and duplex are forced.
+ */
+ ret_val = phy->ops.read_reg(hw, I82580_PHY_CTRL_2, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data &= ~I82580_PHY_CTRL2_AUTO_MDIX;
+ phy_data &= ~I82580_PHY_CTRL2_FORCE_MDI_MDIX;
+
+ ret_val = phy->ops.write_reg(hw, I82580_PHY_CTRL_2, phy_data);
+ if (ret_val)
+ goto out;
+
+ hw_dbg("I82580_PHY_CTRL_2: %X\n", phy_data);
+
+ udelay(1);
+
+ if (phy->autoneg_wait_to_complete) {
+ hw_dbg("Waiting for forced speed/duplex link on 82580 phy\n");
+
+ ret_val = igb_phy_has_link(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+
+ if (!link)
+ hw_dbg("Link taking longer than expected.\n");
+
+ /* Try once more */
+ ret_val = igb_phy_has_link(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_get_phy_info_82580 - Retrieve I82580 PHY information
+ * @hw: pointer to the HW structure
+ *
+ * Read PHY status to determine if link is up. If link is up, then
+ * set/determine 10base-T extended distance and polarity correction. Read
+ * PHY port status to determine MDI/MDIx and speed. Based on the speed,
+ * determine on the cable length, local and remote receiver.
+ **/
+s32 igb_get_phy_info_82580(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+
+ ret_val = igb_phy_has_link(hw, 1, 0, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link) {
+ hw_dbg("Phy info is only valid if link is up\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ phy->polarity_correction = true;
+
+ ret_val = igb_check_polarity_82580(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_reg(hw, I82580_PHY_STATUS_2, &data);
+ if (ret_val)
+ goto out;
+
+ phy->is_mdix = (data & I82580_PHY_STATUS2_MDIX) ? true : false;
+
+ if ((data & I82580_PHY_STATUS2_SPEED_MASK) ==
+ I82580_PHY_STATUS2_SPEED_1000MBPS) {
+ ret_val = hw->phy.ops.get_cable_length(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_reg(hw, PHY_1000T_STATUS, &data);
+ if (ret_val)
+ goto out;
+
+ phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+
+ phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+ } else {
+ phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+ phy->local_rx = e1000_1000t_rx_status_undefined;
+ phy->remote_rx = e1000_1000t_rx_status_undefined;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_get_cable_length_82580 - Determine cable length for 82580 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Reads the diagnostic status register and verifies result is valid before
+ * placing it in the phy_cable_length field.
+ **/
+s32 igb_get_cable_length_82580(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, length;
+
+
+ ret_val = phy->ops.read_reg(hw, I82580_PHY_DIAG_STATUS, &phy_data);
+ if (ret_val)
+ goto out;
+
+ length = (phy_data & I82580_DSTATUS_CABLE_LENGTH) >>
+ I82580_DSTATUS_CABLE_LENGTH_SHIFT;
+
+ if (length == E1000_CABLE_LENGTH_UNDEFINED)
+ ret_val = -E1000_ERR_PHY;
+
+ phy->cable_length = length;
+
+out:
+ return ret_val;
+}
diff --git a/drivers/net/igb/e1000_phy.h b/drivers/net/igb/e1000_phy.h
index adb9436..e23b021 100644
--- a/drivers/net/igb/e1000_phy.h
+++ b/drivers/net/igb/e1000_phy.h
@@ -63,6 +63,11 @@ s32 igb_phy_has_link(struct e1000_hw *hw, u32 iterations,
s32 igb_phy_init_script_igp3(struct e1000_hw *hw);
s32 igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data);
s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
+s32 igb_copper_link_setup_82580(struct e1000_hw *hw);
+s32 igb_check_polarity_82580(struct e1000_hw *hw);
+s32 igb_get_phy_info_82580(struct e1000_hw *hw);
+s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw);
+s32 igb_get_cable_length_82580(struct e1000_hw *hw);
/* IGP01E1000 Specific Registers */
#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* Port Config */
@@ -77,6 +82,33 @@ s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0=MDI, 1=MDIX */
#define IGP01E1000_PSCFR_SMART_SPEED 0x0080
+#define I82580_ADDR_REG 16
+#define I82580_CFG_REG 22
+#define I82580_CFG_ASSERT_CRS_ON_TX (1 << 15)
+#define I82580_CFG_ENABLE_DOWNSHIFT (3 << 10) /* auto downshift 100/10 */
+#define I82580_CTRL_REG 23
+#define I82580_CTRL_DOWNSHIFT_MASK (7 << 10)
+
+/* 82580 specific PHY registers */
+#define I82580_PHY_CTRL_2 18
+#define I82580_PHY_LBK_CTRL 19
+#define I82580_PHY_STATUS_2 26
+#define I82580_PHY_DIAG_STATUS 31
+
+/* I82580 PHY Status 2 */
+#define I82580_PHY_STATUS2_REV_POLARITY 0x0400
+#define I82580_PHY_STATUS2_MDIX 0x0800
+#define I82580_PHY_STATUS2_SPEED_MASK 0x0300
+#define I82580_PHY_STATUS2_SPEED_1000MBPS 0x0200
+#define I82580_PHY_STATUS2_SPEED_100MBPS 0x0100
+
+/* I82580 PHY Control 2 */
+#define I82580_PHY_CTRL2_AUTO_MDIX 0x0400
+#define I82580_PHY_CTRL2_FORCE_MDI_MDIX 0x0200
+
+/* I82580 PHY Diagnostics Status */
+#define I82580_DSTATUS_CABLE_LENGTH 0x03FC
+#define I82580_DSTATUS_CABLE_LENGTH_SHIFT 2
/* Enable flexible speed on link-up */
#define IGP02E1000_PM_D0_LPLU 0x0002 /* For D0a states */
#define IGP02E1000_PM_D3_LPLU 0x0004 /* For all other states */
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [net-next-2.6 PATCH 2/3] igb: add support for 82580 MAC
2009-11-19 22:41 [net-next-2.6 PATCH 1/3] igb: add support for the 82580 phy Jeff Kirsher
@ 2009-11-19 22:42 ` Jeff Kirsher
2009-11-19 22:42 ` [net-next-2.6 PATCH 3/3] igb: Add full support for 82580 devices Jeff Kirsher
2009-11-20 18:00 ` [net-next-2.6 PATCH 1/3] igb: add support for the 82580 phy David Miller
2 siblings, 0 replies; 5+ messages in thread
From: Jeff Kirsher @ 2009-11-19 22:42 UTC (permalink / raw)
To: davem; +Cc: netdev, gospo, Alexander Duyck, Jeff Kirsher
From: Alexander Duyck <alexander.h.duyck@intel.com>
This patch adds support for the 82580 MAC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/igb/e1000_82575.c | 302 ++++++++++++++++++++++++++++++++++-----
drivers/net/igb/e1000_82575.h | 6 +
drivers/net/igb/e1000_defines.h | 10 +
drivers/net/igb/e1000_hw.h | 13 ++
drivers/net/igb/e1000_phy.c | 6 -
drivers/net/igb/e1000_phy.h | 3
drivers/net/igb/e1000_regs.h | 1
7 files changed, 299 insertions(+), 42 deletions(-)
diff --git a/drivers/net/igb/e1000_82575.c b/drivers/net/igb/e1000_82575.c
index 5d345e3..e8e9e91 100644
--- a/drivers/net/igb/e1000_82575.c
+++ b/drivers/net/igb/e1000_82575.c
@@ -46,7 +46,10 @@ static s32 igb_get_cfg_done_82575(struct e1000_hw *);
static s32 igb_init_hw_82575(struct e1000_hw *);
static s32 igb_phy_hw_reset_sgmii_82575(struct e1000_hw *);
static s32 igb_read_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16 *);
+static s32 igb_read_phy_reg_82580(struct e1000_hw *, u32, u16 *);
+static s32 igb_write_phy_reg_82580(struct e1000_hw *, u32, u16);
static s32 igb_reset_hw_82575(struct e1000_hw *);
+static s32 igb_reset_hw_82580(struct e1000_hw *);
static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *, bool);
static s32 igb_setup_copper_link_82575(struct e1000_hw *);
static s32 igb_setup_serdes_link_82575(struct e1000_hw *);
@@ -62,6 +65,12 @@ static s32 igb_reset_init_script_82575(struct e1000_hw *);
static s32 igb_read_mac_addr_82575(struct e1000_hw *);
static s32 igb_set_pcie_completion_timeout(struct e1000_hw *hw);
+static const u16 e1000_82580_rxpbs_table[] =
+ { 36, 72, 144, 1, 2, 4, 8, 16,
+ 35, 70, 140 };
+#define E1000_82580_RXPBS_TABLE_SIZE \
+ (sizeof(e1000_82580_rxpbs_table)/sizeof(u16))
+
static s32 igb_get_invariants_82575(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
@@ -88,6 +97,13 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
case E1000_DEV_ID_82576_SERDES_QUAD:
mac->type = e1000_82576;
break;
+ case E1000_DEV_ID_82580_COPPER:
+ case E1000_DEV_ID_82580_FIBER:
+ case E1000_DEV_ID_82580_SERDES:
+ case E1000_DEV_ID_82580_SGMII:
+ case E1000_DEV_ID_82580_COPPER_DUAL:
+ mac->type = e1000_82580;
+ break;
default:
return -E1000_ERR_MAC_INIT;
break;
@@ -110,6 +126,7 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
dev_spec->sgmii_active = true;
ctrl_ext |= E1000_CTRL_I2C_ENA;
break;
+ case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
hw->phy.media_type = e1000_media_type_internal_serdes;
ctrl_ext |= E1000_CTRL_I2C_ENA;
@@ -121,12 +138,26 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
wr32(E1000_CTRL_EXT, ctrl_ext);
+ /*
+ * if using i2c make certain the MDICNFG register is cleared to prevent
+ * communications from being misrouted to the mdic registers
+ */
+ if ((ctrl_ext & E1000_CTRL_I2C_ENA) && (hw->mac.type == e1000_82580))
+ wr32(E1000_MDICNFG, 0);
+
/* Set mta register count */
mac->mta_reg_count = 128;
/* Set rar entry count */
mac->rar_entry_count = E1000_RAR_ENTRIES_82575;
if (mac->type == e1000_82576)
mac->rar_entry_count = E1000_RAR_ENTRIES_82576;
+ if (mac->type == e1000_82580)
+ mac->rar_entry_count = E1000_RAR_ENTRIES_82580;
+ /* reset */
+ if (mac->type == e1000_82580)
+ mac->ops.reset_hw = igb_reset_hw_82580;
+ else
+ mac->ops.reset_hw = igb_reset_hw_82575;
/* Set if part includes ASF firmware */
mac->asf_firmware_present = true;
/* Set if manageability features are enabled. */
@@ -194,6 +225,10 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
phy->ops.reset = igb_phy_hw_reset_sgmii_82575;
phy->ops.read_reg = igb_read_phy_reg_sgmii_82575;
phy->ops.write_reg = igb_write_phy_reg_sgmii_82575;
+ } else if (hw->mac.type == e1000_82580) {
+ phy->ops.reset = igb_phy_hw_reset;
+ phy->ops.read_reg = igb_read_phy_reg_82580;
+ phy->ops.write_reg = igb_write_phy_reg_82580;
} else {
phy->ops.reset = igb_phy_hw_reset;
phy->ops.read_reg = igb_read_phy_reg_igp;
@@ -225,6 +260,12 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82575;
phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state;
break;
+ case I82580_I_PHY_ID:
+ phy->type = e1000_phy_82580;
+ phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_82580;
+ phy->ops.get_cable_length = igb_get_cable_length_82580;
+ phy->ops.get_phy_info = igb_get_phy_info_82580;
+ break;
default:
return -E1000_ERR_PHY;
}
@@ -635,6 +676,10 @@ static s32 igb_get_cfg_done_82575(struct e1000_hw *hw)
if (hw->bus.func == 1)
mask = E1000_NVM_CFG_DONE_PORT_1;
+ else if (hw->bus.func == E1000_FUNC_2)
+ mask = E1000_NVM_CFG_DONE_PORT_2;
+ else if (hw->bus.func == E1000_FUNC_3)
+ mask = E1000_NVM_CFG_DONE_PORT_3;
while (timeout) {
if (rd32(E1000_EEMNGCTL) & mask)
@@ -754,6 +799,10 @@ void igb_shutdown_serdes_link_82575(struct e1000_hw *hw)
if (hw->bus.func == E1000_FUNC_0)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
+ else if (hw->mac.type == e1000_82580)
+ hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A +
+ NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1,
+ &eeprom_data);
else if (hw->bus.func == E1000_FUNC_1)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
@@ -918,6 +967,9 @@ static s32 igb_setup_copper_link_82575(struct e1000_hw *hw)
goto out;
if (igb_sgmii_active_82575(hw) && !hw->phy.reset_disable) {
+ /* allow time for SFP cage time to power up phy */
+ msleep(300);
+
ret_val = hw->phy.ops.reset(hw);
if (ret_val) {
hw_dbg("Error resetting the PHY.\n");
@@ -931,6 +983,9 @@ static s32 igb_setup_copper_link_82575(struct e1000_hw *hw)
case e1000_phy_igp_3:
ret_val = igb_copper_link_setup_igp(hw);
break;
+ case e1000_phy_82580:
+ ret_val = igb_copper_link_setup_82580(hw);
+ break;
default:
ret_val = -E1000_ERR_PHY;
break;
@@ -955,7 +1010,8 @@ out:
**/
static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
{
- u32 ctrl_reg, reg;
+ u32 ctrl_ext, ctrl_reg, reg;
+ bool pcs_autoneg;
if ((hw->phy.media_type != e1000_media_type_internal_serdes) &&
!igb_sgmii_active_82575(hw))
@@ -970,9 +1026,9 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
wr32(E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
/* power on the sfp cage if present */
- reg = rd32(E1000_CTRL_EXT);
- reg &= ~E1000_CTRL_EXT_SDP3_DATA;
- wr32(E1000_CTRL_EXT, reg);
+ ctrl_ext = rd32(E1000_CTRL_EXT);
+ ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA;
+ wr32(E1000_CTRL_EXT, ctrl_ext);
ctrl_reg = rd32(E1000_CTRL);
ctrl_reg |= E1000_CTRL_SLU;
@@ -989,15 +1045,31 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
reg = rd32(E1000_PCS_LCTL);
- if (igb_sgmii_active_82575(hw)) {
- /* allow time for SFP cage to power up phy */
- msleep(300);
+ /* default pcs_autoneg to the same setting as mac autoneg */
+ pcs_autoneg = hw->mac.autoneg;
- /* AN time out should be disabled for SGMII mode */
+ switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) {
+ case E1000_CTRL_EXT_LINK_MODE_SGMII:
+ /* sgmii mode lets the phy handle forcing speed/duplex */
+ pcs_autoneg = true;
+ /* autoneg time out should be disabled for SGMII mode */
reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT);
- } else {
+ break;
+ case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
+ /* disable PCS autoneg and support parallel detect only */
+ pcs_autoneg = false;
+ default:
+ /*
+ * non-SGMII modes only supports a speed of 1000/Full for the
+ * link so it is best to just force the MAC and let the pcs
+ * link either autoneg or be forced to 1000/Full
+ */
ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD |
E1000_CTRL_FD | E1000_CTRL_FRCDPX;
+
+ /* set speed of 1000/Full if speed/duplex is forced */
+ reg |= E1000_PCS_LCTL_FSV_1000 | E1000_PCS_LCTL_FDV_FULL;
+ break;
}
wr32(E1000_CTRL, ctrl_reg);
@@ -1008,7 +1080,6 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
* mode that will be compatible with older link partners and switches.
* However, both are supported by the hardware and some drivers/tools.
*/
-
reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP |
E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK);
@@ -1018,34 +1089,18 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
*/
reg |= E1000_PCS_LCTL_FORCE_FCTRL;
- /*
- * we always set sgmii to autoneg since it is the phy that will be
- * forcing the link and the serdes is just a go-between
- */
- if (hw->mac.autoneg || igb_sgmii_active_82575(hw)) {
+ if (pcs_autoneg) {
/* Set PCS register for autoneg */
- reg |= E1000_PCS_LCTL_FSV_1000 | /* Force 1000 */
- E1000_PCS_LCTL_FDV_FULL | /* SerDes Full dplx */
- E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
+ reg |= E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */
- hw_dbg("Configuring Autoneg; PCS_LCTL = 0x%08X\n", reg);
+ hw_dbg("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg);
} else {
- /* Check for duplex first */
- if (hw->mac.forced_speed_duplex & E1000_ALL_FULL_DUPLEX)
- reg |= E1000_PCS_LCTL_FDV_FULL;
-
- /* No need to check for 1000/full since the spec states that
- * it requires autoneg to be enabled */
- /* Now set speed */
- if (hw->mac.forced_speed_duplex & E1000_ALL_100_SPEED)
- reg |= E1000_PCS_LCTL_FSV_100;
-
- /* Force speed and force link */
- reg |= E1000_PCS_LCTL_FSD |
- E1000_PCS_LCTL_FORCE_LINK |
- E1000_PCS_LCTL_FLV_LINK_UP;
-
- hw_dbg("Configuring Forced Link; PCS_LCTL = 0x%08X\n", reg);
+ /* Set PCS register for forced link */
+ reg |= E1000_PCS_LCTL_FSD | /* Force Speed */
+ E1000_PCS_LCTL_FORCE_LINK | /* Force Link */
+ E1000_PCS_LCTL_FLV_LINK_UP; /* Force link value up */
+
+ hw_dbg("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg);
}
wr32(E1000_PCS_LCTL, reg);
@@ -1354,8 +1409,183 @@ void igb_vmdq_set_replication_pf(struct e1000_hw *hw, bool enable)
wr32(E1000_VT_CTL, vt_ctl);
}
+/**
+ * igb_read_phy_reg_82580 - Read 82580 MDI control register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the MDI control register in the PHY at offset and stores the
+ * information read to data.
+ **/
+static s32 igb_read_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ u32 mdicnfg = 0;
+ s32 ret_val;
+
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ /*
+ * We config the phy address in MDICNFG register now. Same bits
+ * as before. The values in MDIC can be written but will be
+ * ignored. This allows us to call the old function after
+ * configuring the PHY address in the new register
+ */
+ mdicnfg = (hw->phy.addr << E1000_MDIC_PHY_SHIFT);
+ wr32(E1000_MDICNFG, mdicnfg);
+
+ ret_val = igb_read_phy_reg_mdic(hw, offset, data);
+
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_write_phy_reg_82580 - Write 82580 MDI control register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write to register at offset
+ *
+ * Writes data to MDI control register in the PHY at offset.
+ **/
+static s32 igb_write_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ u32 mdicnfg = 0;
+ s32 ret_val;
+
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ /*
+ * We config the phy address in MDICNFG register now. Same bits
+ * as before. The values in MDIC can be written but will be
+ * ignored. This allows us to call the old function after
+ * configuring the PHY address in the new register
+ */
+ mdicnfg = (hw->phy.addr << E1000_MDIC_PHY_SHIFT);
+ wr32(E1000_MDICNFG, mdicnfg);
+
+ ret_val = igb_write_phy_reg_mdic(hw, offset, data);
+
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_reset_hw_82580 - Reset hardware
+ * @hw: pointer to the HW structure
+ *
+ * This resets function or entire device (all ports, etc.)
+ * to a known state.
+ **/
+static s32 igb_reset_hw_82580(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ /* BH SW mailbox bit in SW_FW_SYNC */
+ u16 swmbsw_mask = E1000_SW_SYNCH_MB;
+ u32 ctrl, icr;
+ bool global_device_reset = hw->dev_spec._82575.global_device_reset;
+
+
+ hw->dev_spec._82575.global_device_reset = false;
+
+ /* Get current control state. */
+ ctrl = rd32(E1000_CTRL);
+
+ /*
+ * Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ ret_val = igb_disable_pcie_master(hw);
+ if (ret_val)
+ hw_dbg("PCI-E Master disable polling has failed.\n");
+
+ hw_dbg("Masking off all interrupts\n");
+ wr32(E1000_IMC, 0xffffffff);
+ wr32(E1000_RCTL, 0);
+ wr32(E1000_TCTL, E1000_TCTL_PSP);
+ wrfl();
+
+ msleep(10);
+
+ /* Determine whether or not a global dev reset is requested */
+ if (global_device_reset &&
+ igb_acquire_swfw_sync_82575(hw, swmbsw_mask))
+ global_device_reset = false;
+
+ if (global_device_reset &&
+ !(rd32(E1000_STATUS) & E1000_STAT_DEV_RST_SET))
+ ctrl |= E1000_CTRL_DEV_RST;
+ else
+ ctrl |= E1000_CTRL_RST;
+
+ wr32(E1000_CTRL, ctrl);
+
+ /* Add delay to insure DEV_RST has time to complete */
+ if (global_device_reset)
+ msleep(5);
+
+ ret_val = igb_get_auto_rd_done(hw);
+ if (ret_val) {
+ /*
+ * When auto config read does not complete, do not
+ * return with an error. This can happen in situations
+ * where there is no eeprom and prevents getting link.
+ */
+ hw_dbg("Auto Read Done did not complete\n");
+ }
+
+ /* If EEPROM is not present, run manual init scripts */
+ if ((rd32(E1000_EECD) & E1000_EECD_PRES) == 0)
+ igb_reset_init_script_82575(hw);
+
+ /* clear global device reset status bit */
+ wr32(E1000_STATUS, E1000_STAT_DEV_RST_SET);
+
+ /* Clear any pending interrupt events. */
+ wr32(E1000_IMC, 0xffffffff);
+ icr = rd32(E1000_ICR);
+
+ /* Install any alternate MAC address into RAR0 */
+ ret_val = igb_check_alt_mac_addr(hw);
+
+ /* Release semaphore */
+ if (global_device_reset)
+ igb_release_swfw_sync_82575(hw, swmbsw_mask);
+
+ return ret_val;
+}
+
+/**
+ * igb_rxpbs_adjust_82580 - adjust RXPBS value to reflect actual RX PBA size
+ * @data: data received by reading RXPBS register
+ *
+ * The 82580 uses a table based approach for packet buffer allocation sizes.
+ * This function converts the retrieved value into the correct table value
+ * 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7
+ * 0x0 36 72 144 1 2 4 8 16
+ * 0x8 35 70 140 rsv rsv rsv rsv rsv
+ */
+u16 igb_rxpbs_adjust_82580(u32 data)
+{
+ u16 ret_val = 0;
+
+ if (data < E1000_82580_RXPBS_TABLE_SIZE)
+ ret_val = e1000_82580_rxpbs_table[data];
+
+ return ret_val;
+}
+
static struct e1000_mac_operations e1000_mac_ops_82575 = {
- .reset_hw = igb_reset_hw_82575,
.init_hw = igb_init_hw_82575,
.check_for_link = igb_check_for_link_82575,
.rar_set = igb_rar_set,
diff --git a/drivers/net/igb/e1000_82575.h b/drivers/net/igb/e1000_82575.h
index b3808ca..d51c992 100644
--- a/drivers/net/igb/e1000_82575.h
+++ b/drivers/net/igb/e1000_82575.h
@@ -38,6 +38,11 @@ extern void igb_rx_fifo_flush_82575(struct e1000_hw *hw);
#define E1000_RAR_ENTRIES_82575 16
#define E1000_RAR_ENTRIES_82576 24
+#define E1000_RAR_ENTRIES_82580 24
+
+#define E1000_SW_SYNCH_MB 0x00000100
+#define E1000_STAT_DEV_RST_SET 0x00100000
+#define E1000_CTRL_DEV_RST 0x20000000
/* SRRCTL bit definitions */
#define E1000_SRRCTL_BSIZEPKT_SHIFT 10 /* Shift _right_ */
@@ -232,5 +237,6 @@ struct e1000_adv_tx_context_desc {
#define E1000_RXPBS_SIZE_MASK_82576 0x0000007F
void igb_vmdq_set_loopback_pf(struct e1000_hw *, bool);
void igb_vmdq_set_replication_pf(struct e1000_hw *, bool);
+u16 igb_rxpbs_adjust_82580(u32 data);
#endif
diff --git a/drivers/net/igb/e1000_defines.h b/drivers/net/igb/e1000_defines.h
index 48fcab0..c58c4fd 100644
--- a/drivers/net/igb/e1000_defines.h
+++ b/drivers/net/igb/e1000_defines.h
@@ -49,6 +49,7 @@
#define E1000_CTRL_EXT_PFRSTD 0x00004000
#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
#define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_1000BASE_KX 0x00400000
#define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000
#define E1000_CTRL_EXT_EIAME 0x01000000
#define E1000_CTRL_EXT_IRCA 0x00000001
@@ -557,8 +558,12 @@
#define NVM_ALT_MAC_ADDR_PTR 0x0037
#define NVM_CHECKSUM_REG 0x003F
-#define E1000_NVM_CFG_DONE_PORT_0 0x40000 /* MNG config cycle done */
-#define E1000_NVM_CFG_DONE_PORT_1 0x80000 /* ...for second port */
+#define E1000_NVM_CFG_DONE_PORT_0 0x040000 /* MNG config cycle done */
+#define E1000_NVM_CFG_DONE_PORT_1 0x080000 /* ...for second port */
+#define E1000_NVM_CFG_DONE_PORT_2 0x100000 /* ...for third port */
+#define E1000_NVM_CFG_DONE_PORT_3 0x200000 /* ...for fourth port */
+
+#define NVM_82580_LAN_FUNC_OFFSET(a) (a ? (0x40 + (0x40 * a)) : 0)
/* Mask bits for fields in Word 0x0f of the NVM */
#define NVM_WORD0F_PAUSE_MASK 0x3000
@@ -625,6 +630,7 @@
*/
#define M88E1111_I_PHY_ID 0x01410CC0
#define IGP03E1000_E_PHY_ID 0x02A80390
+#define I82580_I_PHY_ID 0x015403A0
#define M88_VENDOR 0x0141
/* M88E1000 Specific Registers */
diff --git a/drivers/net/igb/e1000_hw.h b/drivers/net/igb/e1000_hw.h
index 5deda3e..dbaeb5f 100644
--- a/drivers/net/igb/e1000_hw.h
+++ b/drivers/net/igb/e1000_hw.h
@@ -47,19 +47,30 @@ struct e1000_hw;
#define E1000_DEV_ID_82575EB_COPPER 0x10A7
#define E1000_DEV_ID_82575EB_FIBER_SERDES 0x10A9
#define E1000_DEV_ID_82575GB_QUAD_COPPER 0x10D6
+#define E1000_DEV_ID_82580_COPPER 0x150E
+#define E1000_DEV_ID_82580_FIBER 0x150F
+#define E1000_DEV_ID_82580_SERDES 0x1510
+#define E1000_DEV_ID_82580_SGMII 0x1511
+#define E1000_DEV_ID_82580_COPPER_DUAL 0x1516
#define E1000_REVISION_2 2
#define E1000_REVISION_4 4
#define E1000_FUNC_0 0
#define E1000_FUNC_1 1
+#define E1000_FUNC_2 2
+#define E1000_FUNC_3 3
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN0 0
#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN1 3
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN2 6
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN3 9
enum e1000_mac_type {
e1000_undefined = 0,
e1000_82575,
e1000_82576,
+ e1000_82580,
e1000_num_macs /* List is 1-based, so subtract 1 for true count. */
};
@@ -290,6 +301,7 @@ struct e1000_mac_operations {
struct e1000_phy_operations {
s32 (*acquire)(struct e1000_hw *);
+ s32 (*check_polarity)(struct e1000_hw *);
s32 (*check_reset_block)(struct e1000_hw *);
s32 (*force_speed_duplex)(struct e1000_hw *);
s32 (*get_cfg_done)(struct e1000_hw *hw);
@@ -466,6 +478,7 @@ struct e1000_mbx_info {
struct e1000_dev_spec_82575 {
bool sgmii_active;
+ bool global_device_reset;
};
struct e1000_hw {
diff --git a/drivers/net/igb/e1000_phy.c b/drivers/net/igb/e1000_phy.c
index b8fbc85..5c9d73e 100644
--- a/drivers/net/igb/e1000_phy.c
+++ b/drivers/net/igb/e1000_phy.c
@@ -136,7 +136,7 @@ out:
* Reads the MDI control regsiter in the PHY at offset and stores the
* information read to data.
**/
-static s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
+s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
{
struct e1000_phy_info *phy = &hw->phy;
u32 i, mdic = 0;
@@ -194,7 +194,7 @@ out:
*
* Writes data to MDI control register in the PHY at offset.
**/
-static s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
+s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
{
struct e1000_phy_info *phy = &hw->phy;
u32 i, mdic = 0;
@@ -1947,7 +1947,7 @@ s32 igb_phy_init_script_igp3(struct e1000_hw *hw)
*
* Polarity is determined based on the PHY specific status register.
**/
-s32 igb_check_polarity_82580(struct e1000_hw *hw)
+static s32 igb_check_polarity_82580(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
s32 ret_val;
diff --git a/drivers/net/igb/e1000_phy.h b/drivers/net/igb/e1000_phy.h
index e23b021..555eb54 100644
--- a/drivers/net/igb/e1000_phy.h
+++ b/drivers/net/igb/e1000_phy.h
@@ -61,10 +61,11 @@ s32 igb_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
s32 igb_phy_has_link(struct e1000_hw *hw, u32 iterations,
u32 usec_interval, bool *success);
s32 igb_phy_init_script_igp3(struct e1000_hw *hw);
+s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
s32 igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data);
s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
s32 igb_copper_link_setup_82580(struct e1000_hw *hw);
-s32 igb_check_polarity_82580(struct e1000_hw *hw);
s32 igb_get_phy_info_82580(struct e1000_hw *hw);
s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw);
s32 igb_get_cable_length_82580(struct e1000_hw *hw);
diff --git a/drivers/net/igb/e1000_regs.h b/drivers/net/igb/e1000_regs.h
index 934e03b..409c44b 100644
--- a/drivers/net/igb/e1000_regs.h
+++ b/drivers/net/igb/e1000_regs.h
@@ -34,6 +34,7 @@
#define E1000_EERD 0x00014 /* EEPROM Read - RW */
#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */
#define E1000_MDIC 0x00020 /* MDI Control - RW */
+#define E1000_MDICNFG 0x00E04 /* MDI Config - RW */
#define E1000_SCTL 0x00024 /* SerDes Control - RW */
#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */
#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [net-next-2.6 PATCH 3/3] igb: Add full support for 82580 devices
2009-11-19 22:41 [net-next-2.6 PATCH 1/3] igb: add support for the 82580 phy Jeff Kirsher
2009-11-19 22:42 ` [net-next-2.6 PATCH 2/3] igb: add support for 82580 MAC Jeff Kirsher
@ 2009-11-19 22:42 ` Jeff Kirsher
2009-11-20 18:00 ` David Miller
2009-11-20 18:00 ` [net-next-2.6 PATCH 1/3] igb: add support for the 82580 phy David Miller
2 siblings, 1 reply; 5+ messages in thread
From: Jeff Kirsher @ 2009-11-19 22:42 UTC (permalink / raw)
To: davem; +Cc: netdev, gospo, Alexander Duyck, Jeff Kirsher
From: Alexander Duyck <alexander.h.duyck@intel.com>
This patch makes use of the 82580 PHY and MAC support added and adds a set
of supported device IDs for said hardware.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/igb/e1000_defines.h | 7 ++
drivers/net/igb/e1000_regs.h | 4 +
drivers/net/igb/igb.h | 1
drivers/net/igb/igb_ethtool.c | 53 ++++++++++++++++
drivers/net/igb/igb_main.c | 131 ++++++++++++++++++++++++++++++++++++++-
5 files changed, 193 insertions(+), 3 deletions(-)
diff --git a/drivers/net/igb/e1000_defines.h b/drivers/net/igb/e1000_defines.h
index c58c4fd..6e036ae 100644
--- a/drivers/net/igb/e1000_defines.h
+++ b/drivers/net/igb/e1000_defines.h
@@ -330,6 +330,7 @@
#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
#define E1000_ICR_VMMB 0x00000100 /* VM MB event */
+#define E1000_ICR_DRSTA 0x40000000 /* Device Reset Asserted */
/* If this bit asserted, the driver should claim the interrupt */
#define E1000_ICR_INT_ASSERTED 0x80000000
/* LAN connected device generates an interrupt */
@@ -371,6 +372,7 @@
#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_IMS_DRSTA E1000_ICR_DRSTA /* Device Reset Asserted */
#define E1000_IMS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */
/* Extended Interrupt Mask Set */
@@ -379,6 +381,7 @@
/* Interrupt Cause Set */
#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_ICS_DRSTA E1000_ICR_DRSTA /* Device Reset Aserted */
/* Extended Interrupt Cause Set */
@@ -717,4 +720,8 @@
#define E1000_VFTA_ENTRY_MASK 0x7F
#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F
+/* DMA Coalescing register fields */
+#define E1000_PCIEMISC_LX_DECISION 0x00000080 /* Lx power decision based
+ on DMA coal */
+
#endif
diff --git a/drivers/net/igb/e1000_regs.h b/drivers/net/igb/e1000_regs.h
index 409c44b..dd4e6ff 100644
--- a/drivers/net/igb/e1000_regs.h
+++ b/drivers/net/igb/e1000_regs.h
@@ -89,6 +89,8 @@
#define E1000_SYSTIML 0x0B600 /* System time register Low - RO */
#define E1000_SYSTIMH 0x0B604 /* System time register High - RO */
#define E1000_TIMINCA 0x0B608 /* Increment attributes register - RW */
+#define E1000_TSAUXC 0x0B640 /* Timesync Auxiliary Control register */
+#define E1000_SYSTIMR 0x0B6F8 /* System time register Residue */
/* Filtering Registers */
#define E1000_SAQF(_n) (0x5980 + 4 * (_n))
@@ -318,4 +320,6 @@
#define array_rd32(reg, offset) \
(readl(hw->hw_addr + reg + ((offset) << 2)))
+/* DMA Coalescing registers */
+#define E1000_PCIEMISC 0x05BB8 /* PCIE misc config register */
#endif
diff --git a/drivers/net/igb/igb.h b/drivers/net/igb/igb.h
index 63abd1c..c458d9b 100644
--- a/drivers/net/igb/igb.h
+++ b/drivers/net/igb/igb.h
@@ -320,6 +320,7 @@ struct igb_adapter {
#define IGB_FLAG_QUEUE_PAIRS (1 << 3)
#define IGB_82576_TSYNC_SHIFT 19
+#define IGB_82580_TSYNC_SHIFT 24
enum e1000_state_t {
__IGB_TESTING,
__IGB_RESETTING,
diff --git a/drivers/net/igb/igb_ethtool.c b/drivers/net/igb/igb_ethtool.c
index 2e238bf..ac9d527 100644
--- a/drivers/net/igb/igb_ethtool.c
+++ b/drivers/net/igb/igb_ethtool.c
@@ -881,6 +881,49 @@ struct igb_reg_test {
#define TABLE64_TEST_LO 5
#define TABLE64_TEST_HI 6
+/* 82580 reg test */
+static struct igb_reg_test reg_test_82580[] = {
+ { E1000_FCAL, 0x100, 1, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
+ { E1000_FCAH, 0x100, 1, PATTERN_TEST, 0x0000FFFF, 0xFFFFFFFF },
+ { E1000_FCT, 0x100, 1, PATTERN_TEST, 0x0000FFFF, 0xFFFFFFFF },
+ { E1000_VET, 0x100, 1, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
+ { E1000_RDBAL(0), 0x100, 4, PATTERN_TEST, 0xFFFFFF80, 0xFFFFFFFF },
+ { E1000_RDBAH(0), 0x100, 4, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
+ { E1000_RDLEN(0), 0x100, 4, PATTERN_TEST, 0x000FFFF0, 0x000FFFFF },
+ { E1000_RDBAL(4), 0x40, 4, PATTERN_TEST, 0xFFFFFF80, 0xFFFFFFFF },
+ { E1000_RDBAH(4), 0x40, 4, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
+ { E1000_RDLEN(4), 0x40, 4, PATTERN_TEST, 0x000FFFF0, 0x000FFFFF },
+ /* RDH is read-only for 82580, only test RDT. */
+ { E1000_RDT(0), 0x100, 4, PATTERN_TEST, 0x0000FFFF, 0x0000FFFF },
+ { E1000_RDT(4), 0x40, 4, PATTERN_TEST, 0x0000FFFF, 0x0000FFFF },
+ { E1000_FCRTH, 0x100, 1, PATTERN_TEST, 0x0000FFF0, 0x0000FFF0 },
+ { E1000_FCTTV, 0x100, 1, PATTERN_TEST, 0x0000FFFF, 0x0000FFFF },
+ { E1000_TIPG, 0x100, 1, PATTERN_TEST, 0x3FFFFFFF, 0x3FFFFFFF },
+ { E1000_TDBAL(0), 0x100, 4, PATTERN_TEST, 0xFFFFFF80, 0xFFFFFFFF },
+ { E1000_TDBAH(0), 0x100, 4, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
+ { E1000_TDLEN(0), 0x100, 4, PATTERN_TEST, 0x000FFFF0, 0x000FFFFF },
+ { E1000_TDBAL(4), 0x40, 4, PATTERN_TEST, 0xFFFFFF80, 0xFFFFFFFF },
+ { E1000_TDBAH(4), 0x40, 4, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
+ { E1000_TDLEN(4), 0x40, 4, PATTERN_TEST, 0x000FFFF0, 0x000FFFFF },
+ { E1000_TDT(0), 0x100, 4, PATTERN_TEST, 0x0000FFFF, 0x0000FFFF },
+ { E1000_TDT(4), 0x40, 4, PATTERN_TEST, 0x0000FFFF, 0x0000FFFF },
+ { E1000_RCTL, 0x100, 1, SET_READ_TEST, 0xFFFFFFFF, 0x00000000 },
+ { E1000_RCTL, 0x100, 1, SET_READ_TEST, 0x04CFB0FE, 0x003FFFFB },
+ { E1000_RCTL, 0x100, 1, SET_READ_TEST, 0x04CFB0FE, 0xFFFFFFFF },
+ { E1000_TCTL, 0x100, 1, SET_READ_TEST, 0xFFFFFFFF, 0x00000000 },
+ { E1000_RA, 0, 16, TABLE64_TEST_LO,
+ 0xFFFFFFFF, 0xFFFFFFFF },
+ { E1000_RA, 0, 16, TABLE64_TEST_HI,
+ 0x83FFFFFF, 0xFFFFFFFF },
+ { E1000_RA2, 0, 8, TABLE64_TEST_LO,
+ 0xFFFFFFFF, 0xFFFFFFFF },
+ { E1000_RA2, 0, 8, TABLE64_TEST_HI,
+ 0x83FFFFFF, 0xFFFFFFFF },
+ { E1000_MTA, 0, 128, TABLE32_TEST,
+ 0xFFFFFFFF, 0xFFFFFFFF },
+ { 0, 0, 0, 0 }
+};
+
/* 82576 reg test */
static struct igb_reg_test reg_test_82576[] = {
{ E1000_FCAL, 0x100, 1, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
@@ -1013,6 +1056,10 @@ static int igb_reg_test(struct igb_adapter *adapter, u64 *data)
u32 i, toggle;
switch (adapter->hw.mac.type) {
+ case e1000_82580:
+ test = reg_test_82580;
+ toggle = 0x7FEFF3FF;
+ break;
case e1000_82576:
test = reg_test_82576;
toggle = 0x7FFFF3FF;
@@ -1167,6 +1214,9 @@ static int igb_intr_test(struct igb_adapter *adapter, u64 *data)
case e1000_82576:
ics_mask = 0x77D4FBFD;
break;
+ case e1000_82580:
+ ics_mask = 0x77DCFED5;
+ break;
default:
ics_mask = 0x7FFFFFFF;
break;
@@ -1338,6 +1388,9 @@ static int igb_integrated_phy_loopback(struct igb_adapter *adapter)
igb_write_phy_reg(hw, PHY_CONTROL, 0x9140);
/* autoneg off */
igb_write_phy_reg(hw, PHY_CONTROL, 0x8140);
+ } else if (hw->phy.type == e1000_phy_82580) {
+ /* enable MII loopback */
+ igb_write_phy_reg(hw, I82580_PHY_LBK_CTRL, 0x8041);
}
ctrl_reg = rd32(E1000_CTRL);
diff --git a/drivers/net/igb/igb_main.c b/drivers/net/igb/igb_main.c
index 958305e..bb1a6ee 100644
--- a/drivers/net/igb/igb_main.c
+++ b/drivers/net/igb/igb_main.c
@@ -49,7 +49,7 @@
#endif
#include "igb.h"
-#define DRV_VERSION "1.3.16-k2"
+#define DRV_VERSION "2.1.0-k2"
char igb_driver_name[] = "igb";
char igb_driver_version[] = DRV_VERSION;
static const char igb_driver_string[] =
@@ -61,6 +61,11 @@ static const struct e1000_info *igb_info_tbl[] = {
};
static struct pci_device_id igb_pci_tbl[] = {
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_COPPER), board_82575 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_FIBER), board_82575 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_SERDES), board_82575 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_SGMII), board_82575 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_COPPER_DUAL), board_82575 },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82576), board_82575 },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_NS), board_82575 },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_NS_SERDES), board_82575 },
@@ -195,6 +200,16 @@ static cycle_t igb_read_clock(const struct cyclecounter *tc)
u64 stamp = 0;
int shift = 0;
+ /*
+ * The timestamp latches on lowest register read. For the 82580
+ * the lowest register is SYSTIMR instead of SYSTIML. However we never
+ * adjusted TIMINCA so SYSTIMR will just read as all 0s so ignore it.
+ */
+ if (hw->mac.type == e1000_82580) {
+ stamp = rd32(E1000_SYSTIMR) >> 8;
+ shift = IGB_82580_TSYNC_SHIFT;
+ }
+
stamp |= (u64)rd32(E1000_SYSTIML) << shift;
stamp |= (u64)rd32(E1000_SYSTIMH) << (shift + 32);
return stamp;
@@ -304,6 +319,7 @@ static void igb_cache_ring_register(struct igb_adapter *adapter)
Q_IDX_82576(j);
}
case e1000_82575:
+ case e1000_82580:
default:
for (; i < adapter->num_rx_queues; i++)
adapter->rx_ring[i].reg_idx = rbase_offset + i;
@@ -443,6 +459,39 @@ static void igb_assign_vector(struct igb_q_vector *q_vector, int msix_vector)
}
q_vector->eims_value = 1 << msix_vector;
break;
+ case e1000_82580:
+ /* 82580 uses the same table-based approach as 82576 but has fewer
+ entries as a result we carry over for queues greater than 4. */
+ if (rx_queue > IGB_N0_QUEUE) {
+ index = (rx_queue >> 1);
+ ivar = array_rd32(E1000_IVAR0, index);
+ if (rx_queue & 0x1) {
+ /* vector goes into third byte of register */
+ ivar = ivar & 0xFF00FFFF;
+ ivar |= (msix_vector | E1000_IVAR_VALID) << 16;
+ } else {
+ /* vector goes into low byte of register */
+ ivar = ivar & 0xFFFFFF00;
+ ivar |= msix_vector | E1000_IVAR_VALID;
+ }
+ array_wr32(E1000_IVAR0, index, ivar);
+ }
+ if (tx_queue > IGB_N0_QUEUE) {
+ index = (tx_queue >> 1);
+ ivar = array_rd32(E1000_IVAR0, index);
+ if (tx_queue & 0x1) {
+ /* vector goes into high byte of register */
+ ivar = ivar & 0x00FFFFFF;
+ ivar |= (msix_vector | E1000_IVAR_VALID) << 24;
+ } else {
+ /* vector goes into second byte of register */
+ ivar = ivar & 0xFFFF00FF;
+ ivar |= (msix_vector | E1000_IVAR_VALID) << 8;
+ }
+ array_wr32(E1000_IVAR0, index, ivar);
+ }
+ q_vector->eims_value = 1 << msix_vector;
+ break;
default:
BUG();
break;
@@ -484,6 +533,7 @@ static void igb_configure_msix(struct igb_adapter *adapter)
break;
case e1000_82576:
+ case e1000_82580:
/* Turn on MSI-X capability first, or our settings
* won't stick. And it will take days to debug. */
wr32(E1000_GPIE, E1000_GPIE_MSIX_MODE |
@@ -866,6 +916,7 @@ static int igb_request_irq(struct igb_adapter *adapter)
E1000_EICR_TX_QUEUE0 |
E1000_EIMS_OTHER));
break;
+ case e1000_82580:
case e1000_82576:
wr32(E1000_IVAR0, E1000_IVAR_VALID);
break;
@@ -959,10 +1010,15 @@ static void igb_irq_enable(struct igb_adapter *adapter)
wr32(E1000_MBVFIMR, 0xFF);
ims |= E1000_IMS_VMMB;
}
+ if (adapter->hw.mac.type == e1000_82580)
+ ims |= E1000_IMS_DRSTA;
+
wr32(E1000_IMS, ims);
} else {
- wr32(E1000_IMS, IMS_ENABLE_MASK);
- wr32(E1000_IAM, IMS_ENABLE_MASK);
+ wr32(E1000_IMS, IMS_ENABLE_MASK |
+ E1000_IMS_DRSTA);
+ wr32(E1000_IAM, IMS_ENABLE_MASK |
+ E1000_IMS_DRSTA);
}
}
@@ -1184,6 +1240,10 @@ void igb_reset(struct igb_adapter *adapter)
* To take effect CTRL.RST is required.
*/
switch (mac->type) {
+ case e1000_82580:
+ pba = rd32(E1000_RXPBS);
+ pba = igb_rxpbs_adjust_82580(pba);
+ break;
case e1000_82576:
pba = rd32(E1000_RXPBS);
pba &= E1000_RXPBS_SIZE_MASK_82576;
@@ -1278,6 +1338,11 @@ void igb_reset(struct igb_adapter *adapter)
if (hw->mac.ops.init_hw(hw))
dev_err(&pdev->dev, "Hardware Error\n");
+ if (hw->mac.type == e1000_82580) {
+ u32 reg = rd32(E1000_PCIEMISC);
+ wr32(E1000_PCIEMISC,
+ reg & ~E1000_PCIEMISC_LX_DECISION);
+ }
igb_update_mng_vlan(adapter);
/* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
@@ -1508,6 +1573,10 @@ static int __devinit igb_probe(struct pci_dev *pdev,
if (hw->bus.func == 0)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
+ else if (hw->mac.type == e1000_82580)
+ hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A +
+ NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1,
+ &eeprom_data);
else if (hw->bus.func == 1)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
@@ -1746,6 +1815,48 @@ static void igb_init_hw_timer(struct igb_adapter *adapter)
struct e1000_hw *hw = &adapter->hw;
switch (hw->mac.type) {
+ case e1000_82580:
+ memset(&adapter->cycles, 0, sizeof(adapter->cycles));
+ adapter->cycles.read = igb_read_clock;
+ adapter->cycles.mask = CLOCKSOURCE_MASK(64);
+ adapter->cycles.mult = 1;
+ /*
+ * The 82580 timesync updates the system timer every 8ns by 8ns
+ * and the value cannot be shifted. Instead we need to shift
+ * the registers to generate a 64bit timer value. As a result
+ * SYSTIMR/L/H, TXSTMPL/H, RXSTMPL/H all have to be shifted by
+ * 24 in order to generate a larger value for synchronization.
+ */
+ adapter->cycles.shift = IGB_82580_TSYNC_SHIFT;
+ /* disable system timer temporarily by setting bit 31 */
+ wr32(E1000_TSAUXC, 0x80000000);
+ wrfl();
+
+ /* Set registers so that rollover occurs soon to test this. */
+ wr32(E1000_SYSTIMR, 0x00000000);
+ wr32(E1000_SYSTIML, 0x80000000);
+ wr32(E1000_SYSTIMH, 0x000000FF);
+ wrfl();
+
+ /* enable system timer by clearing bit 31 */
+ wr32(E1000_TSAUXC, 0x0);
+ wrfl();
+
+ timecounter_init(&adapter->clock,
+ &adapter->cycles,
+ ktime_to_ns(ktime_get_real()));
+ /*
+ * Synchronize our NIC clock against system wall clock. NIC
+ * time stamp reading requires ~3us per sample, each sample
+ * was pretty stable even under load => only require 10
+ * samples for each offset comparison.
+ */
+ memset(&adapter->compare, 0, sizeof(adapter->compare));
+ adapter->compare.source = &adapter->clock;
+ adapter->compare.target = ktime_get_real;
+ adapter->compare.num_samples = 10;
+ timecompare_update(&adapter->compare, 0);
+ break;
case e1000_82576:
/*
* Initialize hardware timer: we keep it running just in case
@@ -2217,6 +2328,10 @@ static void igb_setup_mrqc(struct igb_adapter *adapter)
if (adapter->vfs_allocated_count) {
/* 82575 and 82576 supports 2 RSS queues for VMDq */
switch (hw->mac.type) {
+ case e1000_82580:
+ num_rx_queues = 1;
+ shift = 0;
+ break;
case e1000_82576:
shift = 3;
num_rx_queues = 2;
@@ -3694,6 +3809,9 @@ static void igb_tx_timeout(struct net_device *netdev)
/* Do the reset outside of interrupt context */
adapter->tx_timeout_count++;
+ if (hw->mac.type == e1000_82580)
+ hw->dev_spec._82575.global_device_reset = true;
+
schedule_work(&adapter->reset_task);
wr32(E1000_EICS,
(adapter->eims_enable_mask & ~adapter->eims_other));
@@ -4700,6 +4818,13 @@ static void igb_systim_to_hwtstamp(struct igb_adapter *adapter,
{
u64 ns;
+ /*
+ * The 82580 starts with 1ns at bit 0 in RX/TXSTMPL, shift this up to
+ * 24 to match clock shift we setup earlier.
+ */
+ if (adapter->hw.mac.type == e1000_82580)
+ regval <<= IGB_82580_TSYNC_SHIFT;
+
ns = timecounter_cyc2time(&adapter->clock, regval);
timecompare_update(&adapter->compare, ns);
memset(shhwtstamps, 0, sizeof(struct skb_shared_hwtstamps));
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [net-next-2.6 PATCH 1/3] igb: add support for the 82580 phy
2009-11-19 22:41 [net-next-2.6 PATCH 1/3] igb: add support for the 82580 phy Jeff Kirsher
2009-11-19 22:42 ` [net-next-2.6 PATCH 2/3] igb: add support for 82580 MAC Jeff Kirsher
2009-11-19 22:42 ` [net-next-2.6 PATCH 3/3] igb: Add full support for 82580 devices Jeff Kirsher
@ 2009-11-20 18:00 ` David Miller
2 siblings, 0 replies; 5+ messages in thread
From: David Miller @ 2009-11-20 18:00 UTC (permalink / raw)
To: jeffrey.t.kirsher; +Cc: netdev, gospo, alexander.h.duyck
From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Date: Thu, 19 Nov 2009 14:41:42 -0800
> From: Alexander Duyck <alexander.h.duyck@intel.com>
>
> This patch adds support for the phy included in the 82580 silicon family.
>
> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Applied.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [net-next-2.6 PATCH 3/3] igb: Add full support for 82580 devices
2009-11-19 22:42 ` [net-next-2.6 PATCH 3/3] igb: Add full support for 82580 devices Jeff Kirsher
@ 2009-11-20 18:00 ` David Miller
0 siblings, 0 replies; 5+ messages in thread
From: David Miller @ 2009-11-20 18:00 UTC (permalink / raw)
To: jeffrey.t.kirsher; +Cc: netdev, gospo, alexander.h.duyck
From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Date: Thu, 19 Nov 2009 14:42:21 -0800
> From: Alexander Duyck <alexander.h.duyck@intel.com>
>
> This patch makes use of the 82580 PHY and MAC support added and adds a set
> of supported device IDs for said hardware.
>
> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Applied.
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2009-11-20 18:00 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-11-19 22:41 [net-next-2.6 PATCH 1/3] igb: add support for the 82580 phy Jeff Kirsher
2009-11-19 22:42 ` [net-next-2.6 PATCH 2/3] igb: add support for 82580 MAC Jeff Kirsher
2009-11-19 22:42 ` [net-next-2.6 PATCH 3/3] igb: Add full support for 82580 devices Jeff Kirsher
2009-11-20 18:00 ` David Miller
2009-11-20 18:00 ` [net-next-2.6 PATCH 1/3] igb: add support for the 82580 phy David Miller
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).