[PATCH 0/3] increase skb size to prevent dma over skb boundary

[PATCH 0/3] increase skb size to prevent dma over skb boundary

[Neil Horman]

Hey all-
	I was tracking down a memory corruptor lately in which, with DEBUG_SLAB
enabled we were getting several redzone violoations, which was always followed
by an oops in the rx receive path when using the e1000e driver.  Looking at the
cores, the slabs that had their redzone violated were always adjacent to a
size-2048 slab which was allocated by __netdev_alloc_skb.  Doing some
instrumentation led me to see the following.  When the e1000e driver sets up its
rctl register, which defines the length of each of the buffers in the rx ring,
we do this:

switch (adapter->rx_buffer_len) {
        case 256:
                rctl |= E1000_RCTL_SZ_256;
                rctl &= ~E1000_RCTL_BSEX;
                break;
        case 512:
                rctl |= E1000_RCTL_SZ_512;
                rctl &= ~E1000_RCTL_BSEX;
                break;
        case 1024:
                rctl |= E1000_RCTL_SZ_1024;
                rctl &= ~E1000_RCTL_BSEX;
                break;
        case 2048:
        default:
                rctl |= E1000_RCTL_SZ_2048;
                rctl &= ~E1000_RCTL_BSEX;
                break;
        case 4096:
                rctl |= E1000_RCTL_SZ_4096;
                break;
        case 8192:
                rctl |= E1000_RCTL_SZ_8192;
                break;
        case 16384:
                rctl |= E1000_RCTL_SZ_16384;
                break;
        }
}

This is problematic since rx_buffer_len is set to 1500, which causes the rctl
value to fall into the default case, which configures the hardware to think it
can dma up to 2048 bytes into each buffer, despite the fact that the buffer is
only 1500 bytes long.  If we receive a frame that is longer than 1500 bytes,
then the dma will overrun the 1500 byte limit of the sk_buff's data block
spilling into the skb_shared_info structure (which is placed immediately after
the end of the skb->end pointer (or at skb->head + skb->end if
NET_SKBUFF_DATA_USES_OFFSET is configured).  In either case, the spillover
corrupts the skb_shared_info structure, and sets us up for any number of
subsequent corruptions/oopses/failures.  I've fixed this by normalizing the
rx_buffer_length value in the setup_rctl function, which rounds up the length to
the configured value of rctl, forcing us to allocate buffers of a size that meet
the hardwares configuration needs. 

I've tested this on e1000e and confirmed that it fixes my redzone violations and
the observed oops.  Visual inspection indicates that e1000 and ixgb also need
this fix.  I've not explicitly tested them though, so I've split this into three
separate patches

Regards
Neil

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>

Re: [PATCH 1/3] e1000: increase skb size to prevent dma over skb boundary

[Neil Horman]

Update e1000 driver to not allow dma beyond the end of the allocated skb
    
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>


e1000_main.c |   34 +++++++++++++++++++++++++++++++++-
1 file changed, 33 insertions(+), 1 deletion(-)


diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
index 7e855f9..7600deb 100644
--- a/drivers/net/e1000/e1000_main.c
+++ b/drivers/net/e1000/e1000_main.c
@@ -1667,6 +1667,19 @@ int e1000_setup_all_rx_resources(struct e1000_adapter *adapter)
 	return err;
 }
 
+static inline u32 normalize_rx_len(u32 len)
+{
+        u32 match, last_match;
+
+
+        for (match = 0x100; match <= 0x4000; match *= 2) {
+                if (len <= match)
+                        return match;
+        }
+
+        return 0;
+}
+
 /**
  * e1000_setup_rctl - configure the receive control registers
  * @adapter: Board private structure
@@ -1675,6 +1688,7 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 {
 	struct e1000_hw *hw = &adapter->hw;
 	u32 rctl;
+	u32 normed_rx_len;
 
 	rctl = er32(RCTL);
 
@@ -1697,7 +1711,25 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 	/* Setup buffer sizes */
 	rctl &= ~E1000_RCTL_SZ_4096;
 	rctl |= E1000_RCTL_BSEX;
-	switch (adapter->rx_buffer_len) {
+
+	/*
+	 * We need to normalize the rx_buffer_len here
+	 * since the hardware only knows about 7 discrete
+	 * frame lengths here.  To accomodate that we need
+	 * to set the rx length in the hardware to the next highest
+	 * size over the rx_buffer_len, then increase rx_buffer_len
+	 * to match it, so that we can get a full mtu sized frame 
+	 */
+	normed_rx_len = normalize_rx_len(adapter->rx_buffer_len);
+	
+	if (!normed_rx_len) {
+		printk(KERN_ERR "No valid rx len found, assume 2048\n");
+		normed_rx_len = 0x800;
+	}
+
+	adapter->rx_buffer_len = normed_rx_len;
+
+	switch (normed_rx_len) {
 		case E1000_RXBUFFER_256:
 			rctl |= E1000_RCTL_SZ_256;
 			rctl &= ~E1000_RCTL_BSEX;

Re: [PATCH 1/3] e1000: increase skb size to prevent dma over skb boundary

[Ben Dooks]

On Mon, Dec 07, 2009 at 09:47:36AM -0500, Neil Horman wrote:
> Update e1000 driver to not allow dma beyond the end of the allocated skb
>     
> Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
> 
> 
> e1000_main.c |   34 +++++++++++++++++++++++++++++++++-
> 1 file changed, 33 insertions(+), 1 deletion(-)
> 
> 
> diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
> index 7e855f9..7600deb 100644
> --- a/drivers/net/e1000/e1000_main.c
> +++ b/drivers/net/e1000/e1000_main.c
> @@ -1667,6 +1667,19 @@ int e1000_setup_all_rx_resources(struct e1000_adapter *adapter)
>  	return err;
>  }
>  
> +static inline u32 normalize_rx_len(u32 len)
> +{
> +        u32 match, last_match;
> +
> +
> +        for (match = 0x100; match <= 0x4000; match *= 2) {
> +                if (len <= match)
> +                        return match;
> +        }
> +
> +        return 0;
> +}

thought there was an ilog2() call in the kernel to do something like
this? see linux/log2.h. will also make it easier to switch on the
result if you've got a value in bit-position instead of size.

-- 
Ben (ben@fluff.org, http://www.fluff.org/)

  'a smiley only costs 4 bytes'

Re: [PATCH 1/3] e1000: increase skb size to prevent dma over skb boundary

[Michał Mirosław]

2009/12/7 Neil Horman <nhorman@tuxdriver.com>:
> Update e1000 driver to not allow dma beyond the end of the allocated skb
>
[...]
> +static inline u32 normalize_rx_len(u32 len)
> +{
> +        u32 match, last_match;
> +
> +
> +        for (match = 0x100; match <= 0x4000; match *= 2) {
> +                if (len <= match)
> +                        return match;
> +        }
> +
> +        return 0;
> +}
> +

You could use roundup_pow_of_two() instead.

Best Regards,
Michał Mirosław

Re: [PATCH 1/3] e1000: increase skb size to prevent dma over skb boundary

[Franco Fichtner]

Hi Neil,

Neil Horman wrote:
> Update e1000 driver to not allow dma beyond the end of the allocated skb
>     
> Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
>
>
> e1000_main.c |   34 +++++++++++++++++++++++++++++++++-
> 1 file changed, 33 insertions(+), 1 deletion(-)
>
>
> diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
> index 7e855f9..7600deb 100644
> --- a/drivers/net/e1000/e1000_main.c
> +++ b/drivers/net/e1000/e1000_main.c
> @@ -1667,6 +1667,19 @@ int e1000_setup_all_rx_resources(struct e1000_adapter *adapter)
>  	return err;
>  }
>  
> +static inline u32 normalize_rx_len(u32 len)
> +{
> +        u32 match, last_match;
> +
>   
Skip newline and get rid of last_match. Also, there is a whitespace error...
> +
> +        for (match = 0x100; match <= 0x4000; match *= 2) {
> +                if (len <= match)
> +                        return match;
> +        }
> +
>   
> +        return 0;
> +}
>   
You should return (match >> 1), which is the largest size possible. (Which
is exactly what you need here).
> +
>  /**
>   * e1000_setup_rctl - configure the receive control registers
>   * @adapter: Board private structure
> @@ -1675,6 +1688,7 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
>  {
>  	struct e1000_hw *hw = &adapter->hw;
>  	u32 rctl;
> +	u32 normed_rx_len;
>  
>  	rctl = er32(RCTL);
>  
> @@ -1697,7 +1711,25 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
>  	/* Setup buffer sizes */
>  	rctl &= ~E1000_RCTL_SZ_4096;
>  	rctl |= E1000_RCTL_BSEX;
> -	switch (adapter->rx_buffer_len) {
> +
> +	/*
> +	 * We need to normalize the rx_buffer_len here
> +	 * since the hardware only knows about 7 discrete
> +	 * frame lengths here.  To accomodate that we need
> +	 * to set the rx length in the hardware to the next highest
> +	 * size over the rx_buffer_len, then increase rx_buffer_len
> +	 * to match it, so that we can get a full mtu sized frame 
> +	 */
> +	normed_rx_len = normalize_rx_len(adapter->rx_buffer_len);
> +	
> +	if (!normed_rx_len) {
> +		printk(KERN_ERR "No valid rx len found, assume 2048\n");
> +		normed_rx_len = 0x800;
> +	}
> +
> +	adapter->rx_buffer_len = normed_rx_len;
>   
If you modify rx_buffer_len anyway, then get rid of normed_rx_len and
do a quick

    adapter->rx_buffer_len = normalize_rx_len(adapter->rx_buffer_len);

instead. With the modification above, it never fails, so no need to check
for !normed_rx_len.

But I don't really know the context of this change. Is it okay to shorten
rx_buffer_len here? Why was it not set appropriately as the driver
expects?

Oh, BTW, the default case in the switch statement is stupid and should
be removed.

> +
> +	switch (normed_rx_len) {
>  		case E1000_RXBUFFER_256:
>  			rctl |= E1000_RCTL_SZ_256;
>  			rctl &= ~E1000_RCTL_BSEX;
> --
> To unsubscribe from this list: send the line "unsubscribe netdev" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>   

Franco

Re: [PATCH 1/3] e1000: increase skb size to prevent dma over skb boundary (v2)

[Neil Horman]

On Mon, Dec 07, 2009 at 04:24:02PM +0100, Franco Fichtner wrote:
> Hi Neil,
>
> Neil Horman wrote:
>> Update e1000 driver to not allow dma beyond the end of the allocated skb
>>     Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
>>
>>
>> e1000_main.c |   34 +++++++++++++++++++++++++++++++++-
>> 1 file changed, 33 insertions(+), 1 deletion(-)
>>
>>
>> diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
>> index 7e855f9..7600deb 100644
>> --- a/drivers/net/e1000/e1000_main.c
>> +++ b/drivers/net/e1000/e1000_main.c
>> @@ -1667,6 +1667,19 @@ int e1000_setup_all_rx_resources(struct e1000_adapter *adapter)
>>  	return err;
>>  }
>>  +static inline u32 normalize_rx_len(u32 len)
>> +{
>> +        u32 match, last_match;
>> +
>>   
> Skip newline and get rid of last_match. Also, there is a whitespace error...
I'll just wash this all out, based on your comments, ben's and Michals, its not
needed..
>> <snip>  
> If you modify rx_buffer_len anyway, then get rid of normed_rx_len and
> do a quick
>
>    adapter->rx_buffer_len = normalize_rx_len(adapter->rx_buffer_len);
>
> instead. With the modification above, it never fails, so no need to check
> for !normed_rx_len.
>
Agreed, by using roundup_pow_of_two as was previously suggested the extra
variable is no longer needed.

> But I don't really know the context of this change. Is it okay to shorten
> rx_buffer_len here? Why was it not set appropriately as the driver
> expects?
>
We're not shortening, we're rounding up.  And yes its both ok, and necessecary.
The problem (from the intial email I sent), was that this driver tells the
hardware that potentially it can dma up to X bytes to a given rx buffer, but it
is possible and likely that we only provide Y bytes to dma to, where X > Y.
This leads to corruption of the skb_shared_info structure.

> Oh, BTW, the default case in the switch statement is stupid and should
> be removed.
>
I agree, its silly, but with the above changes, it becomes needed (or beneficial
again), to catch cases in which roundup_pow_of_two returns a value beyond what
the hardware can handle.  I think in this case we should just panic, as
rx_buffer_len should never be larger than 16384.


Thanks all for the comments, heres version two of this patch, taking all
comments into account:


Update e1000 driver to not allow dma beyond the end of the allocated skb
    
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>


e1000_main.c |   15 ++++++++++++++-
1 file changed, 14 insertions(+), 1 deletion(-)


diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
index 7e855f9..cb16615 100644
--- a/drivers/net/e1000/e1000_main.c
+++ b/drivers/net/e1000/e1000_main.c
@@ -1697,6 +1697,17 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 	/* Setup buffer sizes */
 	rctl &= ~E1000_RCTL_SZ_4096;
 	rctl |= E1000_RCTL_BSEX;
+
+	/*
+	 * We need to normalize the rx_buffer_len here
+	 * since the hardware only knows about 7 discrete
+	 * frame lengths here.  To accomodate that we need
+	 * to set the rx length in the hardware to the next highest
+	 * size over the rx_buffer_len, then increase rx_buffer_len
+	 * to match it, so that we can get a full mtu sized frame
+	 */
+	adapter->rx_buffer_len = roundup_pow_of_two(adapter->rx_buffer_len);
+
 	switch (adapter->rx_buffer_len) {
 		case E1000_RXBUFFER_256:
 			rctl |= E1000_RCTL_SZ_256;
@@ -1711,7 +1722,6 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 			rctl &= ~E1000_RCTL_BSEX;
 			break;
 		case E1000_RXBUFFER_2048:
-		default:
 			rctl |= E1000_RCTL_SZ_2048;
 			rctl &= ~E1000_RCTL_BSEX;
 			break;
@@ -1724,6 +1734,9 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 		case E1000_RXBUFFER_16384:
 			rctl |= E1000_RCTL_SZ_16384;
 			break;
+		default:
+			panic("Bad rx_buffer_len size\n");
+			break;
 	}
 
 	ew32(RCTL, rctl);

Re: [PATCH 1/3] e1000: increase skb size to prevent dma over skb boundary (v2)

[Jeff Kirsher]

On Mon, Dec 7, 2009 at 07:59, Neil Horman <nhorman@tuxdriver.com> wrote:
> On Mon, Dec 07, 2009 at 04:24:02PM +0100, Franco Fichtner wrote:
>> Hi Neil,
>>
>> Neil Horman wrote:
>>> Update e1000 driver to not allow dma beyond the end of the allocated skb
>>>     Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
>>>
>>>
>>> e1000_main.c |   34 +++++++++++++++++++++++++++++++++-
>>> 1 file changed, 33 insertions(+), 1 deletion(-)
>>>
>>>
>>> diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
>>> index 7e855f9..7600deb 100644
>>> --- a/drivers/net/e1000/e1000_main.c
>>> +++ b/drivers/net/e1000/e1000_main.c
>>> @@ -1667,6 +1667,19 @@ int e1000_setup_all_rx_resources(struct e1000_adapter *adapter)
>>>      return err;
>>>  }
>>>  +static inline u32 normalize_rx_len(u32 len)
>>> +{
>>> +        u32 match, last_match;
>>> +
>>>
>> Skip newline and get rid of last_match. Also, there is a whitespace error...
> I'll just wash this all out, based on your comments, ben's and Michals, its not
> needed..
>>> <snip>
>> If you modify rx_buffer_len anyway, then get rid of normed_rx_len and
>> do a quick
>>
>>    adapter->rx_buffer_len = normalize_rx_len(adapter->rx_buffer_len);
>>
>> instead. With the modification above, it never fails, so no need to check
>> for !normed_rx_len.
>>
> Agreed, by using roundup_pow_of_two as was previously suggested the extra
> variable is no longer needed.
>
>> But I don't really know the context of this change. Is it okay to shorten
>> rx_buffer_len here? Why was it not set appropriately as the driver
>> expects?
>>
> We're not shortening, we're rounding up.  And yes its both ok, and necessecary.
> The problem (from the intial email I sent), was that this driver tells the
> hardware that potentially it can dma up to X bytes to a given rx buffer, but it
> is possible and likely that we only provide Y bytes to dma to, where X > Y.
> This leads to corruption of the skb_shared_info structure.
>
>> Oh, BTW, the default case in the switch statement is stupid and should
>> be removed.
>>
> I agree, its silly, but with the above changes, it becomes needed (or beneficial
> again), to catch cases in which roundup_pow_of_two returns a value beyond what
> the hardware can handle.  I think in this case we should just panic, as
> rx_buffer_len should never be larger than 16384.
>
>
> Thanks all for the comments, heres version two of this patch, taking all
> comments into account:
>
>
> Update e1000 driver to not allow dma beyond the end of the allocated skb
>
> Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
>
>
> e1000_main.c |   15 ++++++++++++++-
> 1 file changed, 14 insertions(+), 1 deletion(-)
>
>
> diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
> index 7e855f9..cb16615 100644
> --- a/drivers/net/e1000/e1000_main.c
> +++ b/drivers/net/e1000/e1000_main.c
> @@ -1697,6 +1697,17 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
>        /* Setup buffer sizes */
>        rctl &= ~E1000_RCTL_SZ_4096;
>        rctl |= E1000_RCTL_BSEX;
> +
> +       /*
> +        * We need to normalize the rx_buffer_len here
> +        * since the hardware only knows about 7 discrete
> +        * frame lengths here.  To accomodate that we need
> +        * to set the rx length in the hardware to the next highest
> +        * size over the rx_buffer_len, then increase rx_buffer_len
> +        * to match it, so that we can get a full mtu sized frame
> +        */
> +       adapter->rx_buffer_len = roundup_pow_of_two(adapter->rx_buffer_len);
> +
>        switch (adapter->rx_buffer_len) {
>                case E1000_RXBUFFER_256:
>                        rctl |= E1000_RCTL_SZ_256;
> @@ -1711,7 +1722,6 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
>                        rctl &= ~E1000_RCTL_BSEX;
>                        break;
>                case E1000_RXBUFFER_2048:
> -               default:
>                        rctl |= E1000_RCTL_SZ_2048;
>                        rctl &= ~E1000_RCTL_BSEX;
>                        break;
> @@ -1724,6 +1734,9 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
>                case E1000_RXBUFFER_16384:
>                        rctl |= E1000_RCTL_SZ_16384;
>                        break;
> +               default:
> +                       panic("Bad rx_buffer_len size\n");
> +                       break;
>        }
>
>        ew32(RCTL, rctl);
> --

I have added this patch to my queue of e1000e patches for
reveiw/testing.  Upon successful review/testing I will submit to
Dave/netdev.

-- 
Cheers,
Jeff

------------------------------------------------------------------------------
Join us December 9, 2009 for the Red Hat Virtual Experience,
a free event focused on virtualization and cloud computing. 
Attend in-depth sessions from your desk. Your couch. Anywhere.
http://p.sf.net/sfu/redhat-sfdev2dev
_______________________________________________
E1000-devel mailing list
E1000-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/e1000-devel

Re: [PATCH 2/3] e1000e: increase skb size to prevent dma over skb boundary

[Neil Horman]

Update e1000e driver to not allow dma beyond the end of the allocated skb

Signed-off-by: Neil Horman <nhorman@tuxdrvier.com>


netdev.c |   38 +++++++++++++++++++++++++++++++++++++-
1 file changed, 37 insertions(+), 1 deletion(-)

diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index c3105c5..370bb0f 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -2276,6 +2276,20 @@ static void e1000_configure_tx(struct e1000_adapter *adapter)
 	adapter->tx_queue_len = adapter->netdev->tx_queue_len;
 }
 
+
+static inline u32 normalize_rx_len(u32 len)
+{
+	u32 match, last_match;
+
+
+	for (match = 0x100; match <= 0x4000; match *= 2) {
+		if (len <= match)
+			return match;
+	}
+
+	return 0;
+}
+
 /**
  * e1000_setup_rctl - configure the receive control registers
  * @adapter: Board private structure
@@ -2288,6 +2302,7 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 	u32 rctl, rfctl;
 	u32 psrctl = 0;
 	u32 pages = 0;
+	u32 normed_rx_length;
 
 	/* Program MC offset vector base */
 	rctl = er32(RCTL);
@@ -2332,7 +2347,28 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 	/* Setup buffer sizes */
 	rctl &= ~E1000_RCTL_SZ_4096;
 	rctl |= E1000_RCTL_BSEX;
-	switch (adapter->rx_buffer_len) {
+	/*
+	 * We need to normalize the rx_buffer_len here
+	 * since the hardware only knows about 7 discrete
+	 * frame lengths here.  To accomodate that we need
+	 * to set the rx length in the hardware to the next highest
+	 * size over the rx_buffer_len, then increase rx_buffer_len
+	 * to match it, so that we can get a full mtu sized frame 
+	 */
+	normed_rx_length = normalize_rx_len(adapter->rx_buffer_len);
+
+	if (!normed_rx_length) {
+		printk(KERN_ERR "No valid rx len found, assume 2048\n");
+		normed_rx_length = 0x800;
+	}
+
+	/*
+ 	 * Now we need to bump the rx_len value up so that we allocate
+ 	 * enough data for us to dma into
+ 	 */
+	adapter->rx_buffer_len = normed_rx_length;
+		
+	switch (normed_rx_length) {
 	case 256:
 		rctl |= E1000_RCTL_SZ_256;
 		rctl &= ~E1000_RCTL_BSEX;

Re: [PATCH 2/3] e1000e: increase skb size to prevent dma over skb boundary (v2)

[Neil Horman]

Sorry to reply to myself, but given the comments regarding the e1000 driver, I
should take the same changes into account here.  New version of the patch, much
cleaner than previously.


Update e1000e driver to not allow dma beyond the end of the allocated sk
    
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>


netdev.c |   14 +++++++++++++-
1 file changed, 13 insertions(+), 1 deletion(-)


diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index c3105c5..84e1b5d 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -2332,6 +2332,16 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 	/* Setup buffer sizes */
 	rctl &= ~E1000_RCTL_SZ_4096;
 	rctl |= E1000_RCTL_BSEX;
+	/*
+	 * We need to normalize the rx_buffer_len here
+	 * since the hardware only knows about 7 discrete
+	 * frame lengths here.  To accomodate that we need
+	 * to set the rx length in the hardware to the next highest
+	 * size over the rx_buffer_len, then increase rx_buffer_len
+	 * to match it, so that we can get a full mtu sized frame
+	 */
+	adapter->rx_buffer_len = roundup_pow_of_two(adapter->rx_buffer_len);
+
 	switch (adapter->rx_buffer_len) {
 	case 256:
 		rctl |= E1000_RCTL_SZ_256;
@@ -2346,7 +2356,6 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 		rctl &= ~E1000_RCTL_BSEX;
 		break;
 	case 2048:
-	default:
 		rctl |= E1000_RCTL_SZ_2048;
 		rctl &= ~E1000_RCTL_BSEX;
 		break;
@@ -2359,6 +2368,9 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 	case 16384:
 		rctl |= E1000_RCTL_SZ_16384;
 		break;
+	default:
+		panic("Bad rx_buffer_len size\n");
+		break;
 	}
 
 	/*

Re: [PATCH 2/3] e1000e: increase skb size to prevent dma over skb boundary (v2)

[Jeff Kirsher]

On Mon, Dec 7, 2009 at 08:02, Neil Horman <nhorman@tuxdriver.com> wrote:
> Sorry to reply to myself, but given the comments regarding the e1000 driver, I
> should take the same changes into account here.  New version of the patch, much
> cleaner than previously.
>
>
> Update e1000e driver to not allow dma beyond the end of the allocated sk
>
> Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
>
>
> netdev.c |   14 +++++++++++++-
> 1 file changed, 13 insertions(+), 1 deletion(-)
>
>
> diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
> index c3105c5..84e1b5d 100644
> --- a/drivers/net/e1000e/netdev.c
> +++ b/drivers/net/e1000e/netdev.c
> @@ -2332,6 +2332,16 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
>        /* Setup buffer sizes */
>        rctl &= ~E1000_RCTL_SZ_4096;
>        rctl |= E1000_RCTL_BSEX;
> +       /*
> +        * We need to normalize the rx_buffer_len here
> +        * since the hardware only knows about 7 discrete
> +        * frame lengths here.  To accomodate that we need
> +        * to set the rx length in the hardware to the next highest
> +        * size over the rx_buffer_len, then increase rx_buffer_len
> +        * to match it, so that we can get a full mtu sized frame
> +        */
> +       adapter->rx_buffer_len = roundup_pow_of_two(adapter->rx_buffer_len);
> +
>        switch (adapter->rx_buffer_len) {
>        case 256:
>                rctl |= E1000_RCTL_SZ_256;
> @@ -2346,7 +2356,6 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
>                rctl &= ~E1000_RCTL_BSEX;
>                break;
>        case 2048:
> -       default:
>                rctl |= E1000_RCTL_SZ_2048;
>                rctl &= ~E1000_RCTL_BSEX;
>                break;
> @@ -2359,6 +2368,9 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
>        case 16384:
>                rctl |= E1000_RCTL_SZ_16384;
>                break;
> +       default:
> +               panic("Bad rx_buffer_len size\n");
> +               break;
>        }
>
>        /*
> --

I have added this patch to my queue of e1000e patches for
reveiw/testing.  Upon successful review/testing I will submit to
Dave/netdev.

-- 
Cheers,
Jeff

Re: [PATCH 3/3] ixgb: increase skb size to prevent dma over skb boundary

[Neil Horman]

Update xgb driver to not allow dma beyond the end of the allocated skb
    
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>

ixgb_main.c |   13 +++++++++----
1 file changed, 9 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ixgb/ixgb_main.c b/drivers/net/ixgb/ixgb_main.c
index bcd0f01..2d8e699 100644
--- a/drivers/net/ixgb/ixgb_main.c
+++ b/drivers/net/ixgb/ixgb_main.c
@@ -798,14 +798,19 @@ ixgb_setup_rctl(struct ixgb_adapter *adapter)
 
 	rctl |= IXGB_RCTL_SECRC;
 
-	if (adapter->rx_buffer_len <= IXGB_RXBUFFER_2048)
+	if (adapter->rx_buffer_len <= IXGB_RXBUFFER_2048) {
 		rctl |= IXGB_RCTL_BSIZE_2048;
-	else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_4096)
+		adapter->rx_buffer_len = IXGB_RXBUFFER_2048;
+	} else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_4096) {
 		rctl |= IXGB_RCTL_BSIZE_4096;
-	else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_8192)
+		adapter->rx_buffer_len = IXGB_RXBUFFER_4096;
+	} else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_8192) {
 		rctl |= IXGB_RCTL_BSIZE_8192;
-	else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_16384)
+		adapter->rx_buffer_len = IXGB_RXBUFFER_8192;
+	} else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_16384) {
 		rctl |= IXGB_RCTL_BSIZE_16384;
+		adapter->rx_buffer_len = IXGB_RXBUFFER_16384;
+	}
 
 	IXGB_WRITE_REG(&adapter->hw, RCTL, rctl);
 }

Re: [PATCH 3/3] ixgb: increase skb size to prevent dma over skb boundary

[Jeff Kirsher]

On Mon, Dec 7, 2009 at 06:49, Neil Horman <nhorman@tuxdriver.com> wrote:
> Update xgb driver to not allow dma beyond the end of the allocated skb
>
> Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
>
> ixgb_main.c |   13 +++++++++----
> 1 file changed, 9 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/net/ixgb/ixgb_main.c b/drivers/net/ixgb/ixgb_main.c
> index bcd0f01..2d8e699 100644
> --- a/drivers/net/ixgb/ixgb_main.c
> +++ b/drivers/net/ixgb/ixgb_main.c
> @@ -798,14 +798,19 @@ ixgb_setup_rctl(struct ixgb_adapter *adapter)
>
>        rctl |= IXGB_RCTL_SECRC;
>
> -       if (adapter->rx_buffer_len <= IXGB_RXBUFFER_2048)
> +       if (adapter->rx_buffer_len <= IXGB_RXBUFFER_2048) {
>                rctl |= IXGB_RCTL_BSIZE_2048;
> -       else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_4096)
> +               adapter->rx_buffer_len = IXGB_RXBUFFER_2048;
> +       } else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_4096) {
>                rctl |= IXGB_RCTL_BSIZE_4096;
> -       else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_8192)
> +               adapter->rx_buffer_len = IXGB_RXBUFFER_4096;
> +       } else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_8192) {
>                rctl |= IXGB_RCTL_BSIZE_8192;
> -       else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_16384)
> +               adapter->rx_buffer_len = IXGB_RXBUFFER_8192;
> +       } else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_16384) {
>                rctl |= IXGB_RCTL_BSIZE_16384;
> +               adapter->rx_buffer_len = IXGB_RXBUFFER_16384;
> +       }
>
>        IXGB_WRITE_REG(&adapter->hw, RCTL, rctl);
>  }
> --

I have added this patch to my queue of ixgb patches for
reveiw/testing.  Upon successful review/testing I will submit to
Dave/netdev.

-- 
Cheers,
Jeff

------------------------------------------------------------------------------
Join us December 9, 2009 for the Red Hat Virtual Experience,
a free event focused on virtualization and cloud computing. 
Attend in-depth sessions from your desk. Your couch. Anywhere.
http://p.sf.net/sfu/redhat-sfdev2dev
_______________________________________________
E1000-devel mailing list
E1000-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/e1000-devel

Re: [PATCH 3/3] ixgb: increase skb size to prevent dma over skb boundary

[Neil Horman]

On Mon, Dec 07, 2009 at 12:54:40PM -0800, Jeff Kirsher wrote:
> On Mon, Dec 7, 2009 at 06:49, Neil Horman <nhorman@tuxdriver.com> wrote:
> > Update xgb driver to not allow dma beyond the end of the allocated skb
> >
> > Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
> >
> > ixgb_main.c |   13 +++++++++----
> > 1 file changed, 9 insertions(+), 4 deletions(-)
> >
> > diff --git a/drivers/net/ixgb/ixgb_main.c b/drivers/net/ixgb/ixgb_main.c
> > index bcd0f01..2d8e699 100644
> > --- a/drivers/net/ixgb/ixgb_main.c
> > +++ b/drivers/net/ixgb/ixgb_main.c
> > @@ -798,14 +798,19 @@ ixgb_setup_rctl(struct ixgb_adapter *adapter)
> >
> >        rctl |= IXGB_RCTL_SECRC;
> >
> > -       if (adapter->rx_buffer_len <= IXGB_RXBUFFER_2048)
> > +       if (adapter->rx_buffer_len <= IXGB_RXBUFFER_2048) {
> >                rctl |= IXGB_RCTL_BSIZE_2048;
> > -       else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_4096)
> > +               adapter->rx_buffer_len = IXGB_RXBUFFER_2048;
> > +       } else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_4096) {
> >                rctl |= IXGB_RCTL_BSIZE_4096;
> > -       else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_8192)
> > +               adapter->rx_buffer_len = IXGB_RXBUFFER_4096;
> > +       } else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_8192) {
> >                rctl |= IXGB_RCTL_BSIZE_8192;
> > -       else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_16384)
> > +               adapter->rx_buffer_len = IXGB_RXBUFFER_8192;
> > +       } else if (adapter->rx_buffer_len <= IXGB_RXBUFFER_16384) {
> >                rctl |= IXGB_RCTL_BSIZE_16384;
> > +               adapter->rx_buffer_len = IXGB_RXBUFFER_16384;
> > +       }
> >
> >        IXGB_WRITE_REG(&adapter->hw, RCTL, rctl);
> >  }
> > --
> 
> I have added this patch to my queue of ixgb patches for
> reveiw/testing.  Upon successful review/testing I will submit to
> Dave/netdev.
> 
> -- 
> Cheers,
> Jeff
> 
Um, Well, its already submitted to dave and netdev, but an ACK would sure be 
appreciated pending your review. :)
Neil

Re: [PATCH 3/3] ixgb: increase skb size to prevent dma over skb boundary

[David Miller]

From: Neil Horman <nhorman@tuxdriver.com>
Date: Mon, 7 Dec 2009 15:57:02 -0500

> Um, Well, its already submitted to dave and netdev, but an ACK would
> sure be appreciated pending your review. :)

Since the Intel folks are very responsive, I let all Intel driver
patches flow through Jeff's submission process.

RE: [PATCH 0/3] increase skb size to prevent dma over skb boundary

[Tantilov, Emil S]

Neil Horman wrote:
> Hey all-
> 	I was tracking down a memory corruptor lately in which, with
> DEBUG_SLAB enabled we were getting several redzone violoations, which
> was always followed by an oops in the rx receive path when using the
> e1000e driver.  Looking at the cores, the slabs that had their
> redzone violated were always adjacent to a size-2048 slab which was
> allocated by __netdev_alloc_skb.  Doing some instrumentation led me
> to see the following.  When the e1000e driver sets up its rctl
> register, which defines the length of each of the buffers in the rx
> ring, we do this: 
> 
> switch (adapter->rx_buffer_len) {
>         case 256:
>                 rctl |= E1000_RCTL_SZ_256;
>                 rctl &= ~E1000_RCTL_BSEX;
>                 break;
>         case 512:
>                 rctl |= E1000_RCTL_SZ_512;
>                 rctl &= ~E1000_RCTL_BSEX;
>                 break;
>         case 1024:
>                 rctl |= E1000_RCTL_SZ_1024;
>                 rctl &= ~E1000_RCTL_BSEX;
>                 break;
>         case 2048:
>         default:
>                 rctl |= E1000_RCTL_SZ_2048;
>                 rctl &= ~E1000_RCTL_BSEX;
>                 break;
>         case 4096:
>                 rctl |= E1000_RCTL_SZ_4096;
>                 break;
>         case 8192:
>                 rctl |= E1000_RCTL_SZ_8192;
>                 break;
>         case 16384:
>                 rctl |= E1000_RCTL_SZ_16384;
>                 break;
>         }
> }
> 
> This is problematic since rx_buffer_len is set to 1500, which causes
> the rctl value to fall into the default case, which configures the
> hardware to think it can dma up to 2048 bytes into each buffer,
> despite the fact that the buffer is only 1500 bytes long.  If we
> receive a frame that is longer than 1500 bytes, then the dma will
> overrun the 1500 byte limit of the sk_buff's data block spilling into
> the skb_shared_info structure (which is placed immediately after the
> end of the skb->end pointer (or at skb->head + skb->end if
> NET_SKBUFF_DATA_USES_OFFSET is configured).  In either case, the
> spillover corrupts the skb_shared_info structure, and sets us up for
> any number of subsequent corruptions/oopses/failures.  I've fixed
> this by normalizing the rx_buffer_length value in the setup_rctl
> function, which rounds up the length to the configured value of rctl,
> forcing us to allocate buffers of a size that meet the hardwares
> configuration needs.  
> 
> I've tested this on e1000e and confirmed that it fixes my redzone
> violations and the observed oops.  Visual inspection indicates that
> e1000 and ixgb also need this fix.  I've not explicitly tested them
> though, so I've split this into three separate patches
> 
> Regards
> Neil
> 
> Signed-off-by: Neil Horman <nhorman@tuxdriver.com>

Hi Neil,

I am trying to test the patches you submitted (thanks btw) and so far am not able to reproduce the panic you described. When MTU is at 1500 RCTL.LPE (bit 5) is set to 0 and the HW will not allow the reception of large packets (>1522 bytes, which is what rx_buffer_len is set to). This is basically what I am seeing in my tests - packets are discarded by the HW.

Can you provide more details about the setup you used? Steps to reproduce and also details (lspci -vvv, ethtool -e, ethtool -d) of the HW you used and kernel config should help as well.

Thanks,
Emil

Re: [PATCH 0/3] increase skb size to prevent dma over skb boundary

[Neil Horman]

On Tue, Dec 08, 2009 at 04:37:39PM -0700, Tantilov, Emil S wrote:
> Neil Horman wrote:
> > Hey all-
> > 	I was tracking down a memory corruptor lately in which, with
> > DEBUG_SLAB enabled we were getting several redzone violoations, which
> > was always followed by an oops in the rx receive path when using the
> > e1000e driver.  Looking at the cores, the slabs that had their
> > redzone violated were always adjacent to a size-2048 slab which was
> > allocated by __netdev_alloc_skb.  Doing some instrumentation led me
> > to see the following.  When the e1000e driver sets up its rctl
> > register, which defines the length of each of the buffers in the rx
> > ring, we do this: 
> > 
> > switch (adapter->rx_buffer_len) {
> >         case 256:
> >                 rctl |= E1000_RCTL_SZ_256;
> >                 rctl &= ~E1000_RCTL_BSEX;
> >                 break;
> >         case 512:
> >                 rctl |= E1000_RCTL_SZ_512;
> >                 rctl &= ~E1000_RCTL_BSEX;
> >                 break;
> >         case 1024:
> >                 rctl |= E1000_RCTL_SZ_1024;
> >                 rctl &= ~E1000_RCTL_BSEX;
> >                 break;
> >         case 2048:
> >         default:
> >                 rctl |= E1000_RCTL_SZ_2048;
> >                 rctl &= ~E1000_RCTL_BSEX;
> >                 break;
> >         case 4096:
> >                 rctl |= E1000_RCTL_SZ_4096;
> >                 break;
> >         case 8192:
> >                 rctl |= E1000_RCTL_SZ_8192;
> >                 break;
> >         case 16384:
> >                 rctl |= E1000_RCTL_SZ_16384;
> >                 break;
> >         }
> > }
> > 
> > This is problematic since rx_buffer_len is set to 1500, which causes
> > the rctl value to fall into the default case, which configures the
> > hardware to think it can dma up to 2048 bytes into each buffer,
> > despite the fact that the buffer is only 1500 bytes long.  If we
> > receive a frame that is longer than 1500 bytes, then the dma will
> > overrun the 1500 byte limit of the sk_buff's data block spilling into
> > the skb_shared_info structure (which is placed immediately after the
> > end of the skb->end pointer (or at skb->head + skb->end if
> > NET_SKBUFF_DATA_USES_OFFSET is configured).  In either case, the
> > spillover corrupts the skb_shared_info structure, and sets us up for
> > any number of subsequent corruptions/oopses/failures.  I've fixed
> > this by normalizing the rx_buffer_length value in the setup_rctl
> > function, which rounds up the length to the configured value of rctl,
> > forcing us to allocate buffers of a size that meet the hardwares
> > configuration needs.  
> > 
> > I've tested this on e1000e and confirmed that it fixes my redzone
> > violations and the observed oops.  Visual inspection indicates that
> > e1000 and ixgb also need this fix.  I've not explicitly tested them
> > though, so I've split this into three separate patches
> > 
> > Regards
> > Neil
> > 
> > Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
> 
> Hi Neil,
> 
> I am trying to test the patches you submitted (thanks btw) and so far am not able to reproduce the panic you described. When MTU is at 1500 RCTL.LPE (bit 5) is set to 0 and the HW will not allow the reception of large packets (>1522 bytes, which is what rx_buffer_len is set to). This is basically what I am seeing in my tests - packets are discarded by the HW.
> 
Interestingly, the only time we could observe the errors was when SLAB_DEBUG was
configured, so my guess is timing plays an important role.  The problem also
only reproduced on hp-z200 series systems (with e1000e cards in them having pci
vendor device ids  14e4:1684), so perhaps this is restricted to certain hardware
revisions?

> Can you provide more details about the setup you used? Steps to reproduce and also details (lspci -vvv, ethtool -e, ethtool -d) of the HW you used and kernel config should help as well.

Basically I ran a kernel with CONFIG_SLAB_DEBUG turned on on one of the above
systms, and ran the connectathon suite on it.

I don't have access to the system at this minute but, I'll reserve it as soon as
I'm able and dig up the full lspci dump and ethtool info for you.

I will point out though, that in e1000_change_mtu for all the drivers I've
posted modifications for, this normalization of rx_buffer_len is already done,
so there seems to be some precident for doing this operation.

Thanks & Regards
Neil

> 
> Thanks,
> Emil--
> To unsubscribe from this list: send the line "unsubscribe netdev" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 

Re: [PATCH 0/3] increase skb size to prevent dma over skb boundary

[Neil Horman]

[-- Attachment #1: Type: text/plain, Size: 4101 bytes --]

On Tue, Dec 08, 2009 at 04:37:39PM -0700, Tantilov, Emil S wrote:
> Neil Horman wrote:
> > Hey all-
> > 	I was tracking down a memory corruptor lately in which, with
> > DEBUG_SLAB enabled we were getting several redzone violoations, which
> > was always followed by an oops in the rx receive path when using the
> > e1000e driver.  Looking at the cores, the slabs that had their
> > redzone violated were always adjacent to a size-2048 slab which was
> > allocated by __netdev_alloc_skb.  Doing some instrumentation led me
> > to see the following.  When the e1000e driver sets up its rctl
> > register, which defines the length of each of the buffers in the rx
> > ring, we do this: 
> > 
> > switch (adapter->rx_buffer_len) {
> >         case 256:
> >                 rctl |= E1000_RCTL_SZ_256;
> >                 rctl &= ~E1000_RCTL_BSEX;
> >                 break;
> >         case 512:
> >                 rctl |= E1000_RCTL_SZ_512;
> >                 rctl &= ~E1000_RCTL_BSEX;
> >                 break;
> >         case 1024:
> >                 rctl |= E1000_RCTL_SZ_1024;
> >                 rctl &= ~E1000_RCTL_BSEX;
> >                 break;
> >         case 2048:
> >         default:
> >                 rctl |= E1000_RCTL_SZ_2048;
> >                 rctl &= ~E1000_RCTL_BSEX;
> >                 break;
> >         case 4096:
> >                 rctl |= E1000_RCTL_SZ_4096;
> >                 break;
> >         case 8192:
> >                 rctl |= E1000_RCTL_SZ_8192;
> >                 break;
> >         case 16384:
> >                 rctl |= E1000_RCTL_SZ_16384;
> >                 break;
> >         }
> > }
> > 
> > This is problematic since rx_buffer_len is set to 1500, which causes
> > the rctl value to fall into the default case, which configures the
> > hardware to think it can dma up to 2048 bytes into each buffer,
> > despite the fact that the buffer is only 1500 bytes long.  If we
> > receive a frame that is longer than 1500 bytes, then the dma will
> > overrun the 1500 byte limit of the sk_buff's data block spilling into
> > the skb_shared_info structure (which is placed immediately after the
> > end of the skb->end pointer (or at skb->head + skb->end if
> > NET_SKBUFF_DATA_USES_OFFSET is configured).  In either case, the
> > spillover corrupts the skb_shared_info structure, and sets us up for
> > any number of subsequent corruptions/oopses/failures.  I've fixed
> > this by normalizing the rx_buffer_length value in the setup_rctl
> > function, which rounds up the length to the configured value of rctl,
> > forcing us to allocate buffers of a size that meet the hardwares
> > configuration needs.  
> > 
> > I've tested this on e1000e and confirmed that it fixes my redzone
> > violations and the observed oops.  Visual inspection indicates that
> > e1000 and ixgb also need this fix.  I've not explicitly tested them
> > though, so I've split this into three separate patches
> > 
> > Regards
> > Neil
> > 
> > Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
> 
> Hi Neil,
> 
> I am trying to test the patches you submitted (thanks btw) and so far am not able to reproduce the panic you described. When MTU is at 1500 RCTL.LPE (bit 5) is set to 0 and the HW will not allow the reception of large packets (>1522 bytes, which is what rx_buffer_len is set to). This is basically what I am seeing in my tests - packets are discarded by the HW.
> 
> Can you provide more details about the setup you used? Steps to reproduce and also details (lspci -vvv, ethtool -e, ethtool -d) of the HW you used and kernel config should help as well.
> 
> Thanks,
> Emil--
> To unsubscribe from this list: send the line "unsubscribe netdev" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 


Heres the data you asked for.  The config isn't exact, as the system in question
was installed a few times over since I worked on this, but it should be very
close.  The only differnce I see on this config is that CONFIG_SLAB_DEBUG is
turned on.  Everything else should be identical

Neil


[-- Attachment #2: config --]
[-- Type: text/plain, Size: 65817 bytes --]

CONFIG_X86_64=y
CONFIG_64BIT=y
CONFIG_X86=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_GET_USER_PAGES_FAST=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_MMU=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_CMPXCHG=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DMI=y
CONFIG_AUDIT_ARCH=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32

#
# General setup
#
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
CONFIG_TASKSTATS=y
CONFIG_TASK_DELAY_ACCT=y
CONFIG_TASK_IO_ACCOUNTING=y
CONFIG_AUDIT=y
CONFIG_AUDITSYSCALL=y
# CONFIG_IKCONFIG is not set
CONFIG_CPUSETS=y
CONFIG_RELAY=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_TRACEPOINTS=y
CONFIG_MARKERS=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_MODULE_SIG=y
# CONFIG_MODULE_SIG_FORCE is not set
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y

#
# Process debugging support
#
CONFIG_PTRACE=y
CONFIG_UTRACE=y

#
# Block layer
#
CONFIG_LBD=y
CONFIG_BLK_DEV_IO_TRACE=y
CONFIG_LSF=y

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"

#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_VSMP is not set
# CONFIG_MK8 is not set
# CONFIG_MPSC is not set
CONFIG_GENERIC_CPU=y
# CONFIG_X86_64_XEN is not set
CONFIG_X86_L1_CACHE_BYTES=128
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_X86_INTERNODE_CACHE_BYTES=128
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_MICROCODE=m
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
CONFIG_X86_HT=y
# CONFIG_EFI is not set
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_MTRR=y
CONFIG_SMP=y
CONFIG_SCHED_SMT=y
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
CONFIG_PREEMPT_BKL=y
CONFIG_PREEMPT_NOTIFIERS=y
CONFIG_NUMA=y
CONFIG_K8_NUMA=y
CONFIG_NODES_SHIFT=6
CONFIG_X86_64_ACPI_NUMA=y
# CONFIG_NUMA_EMU is not set
CONFIG_ARCH_DISCONTIGMEM_ENABLE=y
CONFIG_ARCH_DISCONTIGMEM_DEFAULT=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_MEMORY_PROBE=y
CONFIG_SELECT_MEMORY_MODEL=y
# CONFIG_FLATMEM_MANUAL is not set
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_SPARSEMEM_MANUAL=y
CONFIG_SPARSEMEM=y
CONFIG_NEED_MULTIPLE_NODES=y
CONFIG_HAVE_MEMORY_PRESENT=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPARSEMEM_EXTREME=y
CONFIG_MEMORY_HOTPLUG=y

#
# Memory hotplug is not guaranteed to work with Software Suspend
#
CONFIG_MEMORY_HOTPLUG_SPARSE=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
CONFIG_RESOURCES_64BIT=y
CONFIG_MMU_NOTIFIER=y
CONFIG_MMU_NOTIFIER_TABSZ=512
CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID=y
CONFIG_NR_CPUS=255
CONFIG_HOTPLUG_CPU=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_TRACK_DIRTY_PAGES=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_TICK_DIVIDER=y
CONFIG_IOMMU=y
CONFIG_CALGARY_IOMMU=y
# CONFIG_CALGARY_IOMMU_ENABLED_BY_DEFAULT is not set
CONFIG_AMD_IOMMU=y
CONFIG_IOMMU_HELPER=y
CONFIG_SWIOTLB=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_INTEL=y
CONFIG_X86_MCE_AMD=y
CONFIG_KEXEC=y
CONFIG_CRASH_DUMP=y
# CONFIG_SECCOMP is not set
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
CONFIG_REORDER=y
CONFIG_K8_NB=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_ISA_DMA_API=y
CONFIG_GENERIC_PENDING_IRQ=y

#
# Power management options
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
CONFIG_SOFTWARE_SUSPEND=y
CONFIG_PM_STD_PARTITION=""
CONFIG_SUSPEND_SMP=y

#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
# CONFIG_ACPI_SLEEP_PROC_SLEEP is not set
CONFIG_ACPI_AC=m
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
# CONFIG_ACPI_HOTKEY is not set
CONFIG_ACPI_FAN=y
CONFIG_ACPI_DOCK=y
# CONFIG_ACPI_BAY is not set
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_NUMA=y
CONFIG_ACPI_ASUS=m
# CONFIG_ACPI_IBM is not set
CONFIG_ACPI_TOSHIBA=m
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=y
CONFIG_ACPI_HOTPLUG_MEMORY=m
CONFIG_ACPI_SBS=m
CONFIG_THINKPAD_ACPI=m
# CONFIG_THINKPAD_ACPI_DEBUG is not set
CONFIG_THINKPAD_ACPI_BAY=y
CONFIG_THINKPAD_ACPI_VIDEO=y
CONFIG_THINKPAD_ACPI_HOTKEY_POLL=y

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=m
CONFIG_CPU_FREQ_DEBUG=y
CONFIG_CPU_FREQ_STAT=m
CONFIG_CPU_FREQ_STAT_DETAILS=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=m
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m

#
# CPUFreq processor drivers
#
CONFIG_X86_POWERNOW_K8=m
CONFIG_X86_POWERNOW_K8_ACPI=y
CONFIG_X86_SPEEDSTEP_CENTRINO=m
CONFIG_X86_SPEEDSTEP_CENTRINO_ACPI=y
CONFIG_X86_ACPI_CPUFREQ=m

#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
# CONFIG_X86_SPEEDSTEP_LIB is not set

#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_VIRTIO=m
CONFIG_VIRTIO_RING=m
CONFIG_VIRTIO_PCI=m
CONFIG_IOMMU_API=y
CONFIG_DMAR=y
# CONFIG_DMAR_DEFAULT_ON is not set
CONFIG_DMAR_GFX_WA=y
CONFIG_DMAR_FLOPPY_WA=y
CONFIG_PCIEPORTBUS=y
CONFIG_HOTPLUG_PCI_PCIE=m
# CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE is not set
CONFIG_PCI_DOMAINS=y
CONFIG_PCI_MSI=y
# CONFIG_PCI_DEBUG is not set
CONFIG_PCI_STUB=y
CONFIG_PCI_IOV=y

#
# PCCARD (PCMCIA/CardBus) support
#
CONFIG_PCCARD=y
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=y
CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_PCMCIA_IOCTL=y
CONFIG_CARDBUS=y

#
# PC-card bridges
#
CONFIG_YENTA=y
CONFIG_YENTA_O2=y
CONFIG_YENTA_RICOH=y
CONFIG_YENTA_TI=y
CONFIG_YENTA_ENE_TUNE=y
CONFIG_YENTA_TOSHIBA=y
CONFIG_PD6729=m
# CONFIG_I82092 is not set
CONFIG_PCCARD_NONSTATIC=y

#
# PCI Hotplug Support
#
CONFIG_HOTPLUG_PCI=y
CONFIG_HOTPLUG_PCI_FAKE=m
CONFIG_HOTPLUG_PCI_ACPI=m
CONFIG_HOTPLUG_PCI_ACPI_IBM=m
# CONFIG_HOTPLUG_PCI_CPCI is not set
CONFIG_HOTPLUG_PCI_SHPC=m
# CONFIG_HOTPLUG_PCI_SHPC_POLL_EVENT_MODE is not set

#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
CONFIG_IA32_EMULATION=y
# CONFIG_IA32_AOUT is not set
CONFIG_COMPAT=y
CONFIG_SYSVIPC_COMPAT=y

#
# Networking
#
CONFIG_NET=y

#
# Networking options
#
# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_NALGO=m
CONFIG_XFRM_USER=y
CONFIG_NET_KEY=m
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_FWMARK=y
CONFIG_IP_ROUTE_MULTIPATH=y
# CONFIG_IP_ROUTE_MULTIPATH_CACHED is not set
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_DIAG=m
CONFIG_INET_TCP_DIAG=m
CONFIG_TCP_CONG_ADVANCED=y

#
# TCP congestion control
#
CONFIG_TCP_CONG_BIC=y
CONFIG_TCP_CONG_CUBIC=m
CONFIG_TCP_CONG_WESTWOOD=m
CONFIG_TCP_CONG_HTCP=m
CONFIG_TCP_CONG_HSTCP=m
CONFIG_TCP_CONG_HYBLA=m
CONFIG_TCP_CONG_VEGAS=m
CONFIG_TCP_CONG_SCALABLE=m
CONFIG_TCP_CONG_LP=m
CONFIG_TCP_CONG_VENO=m
CONFIG_INET_LRO=y

#
# IP: Virtual Server Configuration
#
CONFIG_IP_VS=m
# CONFIG_IP_VS_DEBUG is not set
CONFIG_IP_VS_TAB_BITS=12

#
# IPVS transport protocol load balancing support
#
CONFIG_IP_VS_PROTO_TCP=y
CONFIG_IP_VS_PROTO_UDP=y
CONFIG_IP_VS_PROTO_ESP=y
CONFIG_IP_VS_PROTO_AH=y

#
# IPVS scheduler
#
CONFIG_IP_VS_RR=m
CONFIG_IP_VS_WRR=m
CONFIG_IP_VS_LC=m
CONFIG_IP_VS_WLC=m
CONFIG_IP_VS_LBLC=m
CONFIG_IP_VS_LBLCR=m
CONFIG_IP_VS_DH=m
CONFIG_IP_VS_SH=m
CONFIG_IP_VS_SED=m
CONFIG_IP_VS_NQ=m

#
# IPVS application helper
#
CONFIG_IP_VS_FTP=m
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
CONFIG_IPV6_ROUTE_INFO=y
CONFIG_IPV6_OPTIMISTIC_DAD=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_INET6_XFRM_TUNNEL=m
CONFIG_INET6_TUNNEL=m
CONFIG_INET6_XFRM_MODE_TRANSPORT=m
CONFIG_INET6_XFRM_MODE_TUNNEL=m
CONFIG_IPV6_TUNNEL=m
# CONFIG_IPV6_SUBTREES is not set
CONFIG_IPV6_MULTIPLE_TABLES=y
CONFIG_IPV6_ROUTE_FWMARK=y
CONFIG_NETWORK_SECMARK=y
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_BRIDGE_NETFILTER=y

#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=m
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
CONFIG_NETFILTER_XT_TARGET_SECMARK=m
CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
CONFIG_NETFILTER_XT_MATCH_DCCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HELPER=m
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_QUOTA=m
CONFIG_NETFILTER_XT_MATCH_REALM=m
CONFIG_NETFILTER_XT_MATCH_SCTP=m
CONFIG_NETFILTER_XT_MATCH_STATE=m
CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
CONFIG_NETFILTER_XT_MATCH_STRING=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m

#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_CT_ACCT=y
CONFIG_IP_NF_CONNTRACK_MARK=y
CONFIG_IP_NF_CONNTRACK_SECMARK=y
CONFIG_IP_NF_CONNTRACK_EVENTS=y
CONFIG_IP_NF_CONNTRACK_NETLINK=m
CONFIG_IP_NF_CT_PROTO_SCTP=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_NETBIOS_NS=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_PPTP=m
CONFIG_IP_NF_H323=m
CONFIG_IP_NF_SIP=m
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_HASHLIMIT=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
CONFIG_IP_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_NAT_PPTP=m
CONFIG_IP_NF_NAT_H323=m
CONFIG_IP_NF_NAT_SIP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m

#
# IPv6: Netfilter Configuration (EXPERIMENTAL)
#
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_HL=m
CONFIG_IP6_NF_RAW=m

#
# Bridge: Netfilter Configuration
#
CONFIG_BRIDGE_NF_EBTABLES=m
CONFIG_BRIDGE_EBT_BROUTE=m
CONFIG_BRIDGE_EBT_T_FILTER=m
CONFIG_BRIDGE_EBT_T_NAT=m
CONFIG_BRIDGE_EBT_802_3=m
CONFIG_BRIDGE_EBT_AMONG=m
CONFIG_BRIDGE_EBT_ARP=m
CONFIG_BRIDGE_EBT_IP=m
CONFIG_BRIDGE_EBT_LIMIT=m
CONFIG_BRIDGE_EBT_MARK=m
CONFIG_BRIDGE_EBT_PKTTYPE=m
CONFIG_BRIDGE_EBT_STP=m
CONFIG_BRIDGE_EBT_VLAN=m
CONFIG_BRIDGE_EBT_ARPREPLY=m
CONFIG_BRIDGE_EBT_DNAT=m
CONFIG_BRIDGE_EBT_MARK_T=m
CONFIG_BRIDGE_EBT_REDIRECT=m
CONFIG_BRIDGE_EBT_SNAT=m
CONFIG_BRIDGE_EBT_LOG=m
CONFIG_BRIDGE_EBT_ULOG=m

#
# DCCP Configuration (EXPERIMENTAL)
#
CONFIG_IP_DCCP=m
CONFIG_INET_DCCP_DIAG=m
CONFIG_IP_DCCP_ACKVEC=y

#
# DCCP CCIDs Configuration (EXPERIMENTAL)
#
CONFIG_IP_DCCP_CCID2=m
CONFIG_IP_DCCP_CCID3=m
CONFIG_IP_DCCP_TFRC_LIB=m

#
# DCCP Kernel Hacking
#
# CONFIG_IP_DCCP_DEBUG is not set

#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
# CONFIG_SCTP_HMAC_NONE is not set
# CONFIG_SCTP_HMAC_SHA1 is not set
CONFIG_SCTP_HMAC_MD5=y
CONFIG_RDS=m
# CONFIG_RDS_DEBUG is not set

#
# TIPC Configuration (EXPERIMENTAL)
#
CONFIG_TIPC=m
# CONFIG_TIPC_ADVANCED is not set
# CONFIG_TIPC_DEBUG is not set
CONFIG_ATM=m
CONFIG_ATM_CLIP=m
# CONFIG_ATM_CLIP_NO_ICMP is not set
CONFIG_ATM_LANE=m
# CONFIG_ATM_MPOA is not set
CONFIG_ATM_BR2684=m
# CONFIG_ATM_BR2684_IPFILTER is not set
CONFIG_BRIDGE=m
CONFIG_VLAN_8021Q=m
# CONFIG_DECNET is not set
CONFIG_LLC=y
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set

#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
# CONFIG_NET_SCH_CLK_JIFFIES is not set
CONFIG_NET_SCH_CLK_GETTIMEOFDAY=y
# CONFIG_NET_SCH_CLK_CPU is not set

#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_ATM=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_INGRESS=m

#
# Classification
#
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=m
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
CONFIG_CLS_U32_PERF=y
CONFIG_CLS_U32_MARK=y
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_EMATCH=y
CONFIG_NET_EMATCH_STACK=32
CONFIG_NET_EMATCH_CMP=m
CONFIG_NET_EMATCH_NBYTE=m
CONFIG_NET_EMATCH_U32=m
CONFIG_NET_EMATCH_META=m
CONFIG_NET_EMATCH_TEXT=m
CONFIG_NET_CLS_ACT=y
CONFIG_NET_ACT_POLICE=m
CONFIG_NET_ACT_GACT=m
CONFIG_GACT_PROB=y
CONFIG_NET_ACT_MIRRED=m
CONFIG_NET_ACT_IPT=m
CONFIG_NET_ACT_PEDIT=m
CONFIG_NET_ACT_SIMP=m
CONFIG_NET_CLS_IND=y
CONFIG_NET_ESTIMATOR=y

#
# Network testing
#
CONFIG_NET_PKTGEN=m
# CONFIG_NET_TCPPROBE is not set
CONFIG_NET_DROP_MONITOR=y
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_CMTP=m
CONFIG_BT_HIDP=m

#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIDTL1=m
CONFIG_BT_HCIBT3C=m
CONFIG_BT_HCIBLUECARD=m
CONFIG_BT_HCIBTUART=m
CONFIG_BT_HCIVHCI=m
CONFIG_TUX=m

#
# TUX options
#
CONFIG_TUX_EXTCGI=y
CONFIG_TUX_EXTENDED_LOG=y
# CONFIG_TUX_DEBUG is not set
CONFIG_NETLABEL=y
CONFIG_FIB_RULES=y

#
# Wireless
#
CONFIG_CFG80211=m
CONFIG_NL80211=y
CONFIG_WIRELESS_EXT=y
CONFIG_NET_WIRELESS_RTNETLINK=y
CONFIG_MAC80211=m

#
# Rate control algorithm selection
#
CONFIG_MAC80211_RC_DEFAULT_PID=y
# CONFIG_MAC80211_RC_DEFAULT_NONE is not set

#
# Selecting 'y' for an algorithm will
#

#
# build the algorithm into mac80211.
#
CONFIG_MAC80211_RC_DEFAULT="pid"
CONFIG_MAC80211_RC_PID=y
# CONFIG_MAC80211_MESH is not set
CONFIG_MAC80211_LEDS=y
# CONFIG_MAC80211_DEBUGFS is not set
# CONFIG_MAC80211_DEBUG_PACKET_ALIGNMENT is not set
# CONFIG_MAC80211_DEBUG is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
CONFIG_IEEE80211_SOFTMAC=m
CONFIG_IEEE80211_SOFTMAC_DEBUG=y

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set

#
# Connector - unified userspace <-> kernelspace linker
#
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y

#
# Memory Technology Devices (MTD)
#
CONFIG_MTD=m
# CONFIG_MTD_DEBUG is not set
CONFIG_MTD_CONCAT=m
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_REDBOOT_PARTS=m
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
CONFIG_MTD_CMDLINE_PARTS=y

#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=m
CONFIG_MTD_BLOCK=m
CONFIG_MTD_BLOCK_RO=m
CONFIG_FTL=m
CONFIG_NFTL=m
CONFIG_NFTL_RW=y
# CONFIG_INFTL is not set
CONFIG_RFD_FTL=m

#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=m
CONFIG_MTD_JEDECPROBE=m
CONFIG_MTD_GEN_PROBE=m
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
CONFIG_MTD_CFI_INTELEXT=m
CONFIG_MTD_CFI_AMDSTD=m
CONFIG_MTD_CFI_STAA=m
CONFIG_MTD_CFI_UTIL=m
CONFIG_MTD_RAM=m
CONFIG_MTD_ROM=m
CONFIG_MTD_ABSENT=m
# CONFIG_MTD_OBSOLETE_CHIPS is not set

#
# Mapping drivers for chip access
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
# CONFIG_MTD_PHYSMAP is not set
# CONFIG_MTD_PNC2000 is not set
CONFIG_MTD_SC520CDP=m
CONFIG_MTD_NETSC520=m
CONFIG_MTD_TS5500=m
# CONFIG_MTD_AMD76XROM is not set
# CONFIG_MTD_ICHXROM is not set
CONFIG_MTD_SCB2_FLASH=m
# CONFIG_MTD_NETtel is not set
# CONFIG_MTD_DILNETPC is not set
# CONFIG_MTD_L440GX is not set
# CONFIG_MTD_PLATRAM is not set

#
# Self-contained MTD device drivers
#
# CONFIG_MTD_PMC551 is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
CONFIG_MTD_MTDRAM=m
CONFIG_MTDRAM_TOTAL_SIZE=4096
CONFIG_MTDRAM_ERASE_SIZE=128
CONFIG_MTD_BLOCK2MTD=m

#
# Disk-On-Chip Device Drivers
#
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set

#
# NAND Flash Device Drivers
#
CONFIG_MTD_NAND=m
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
CONFIG_MTD_NAND_ECC_SMC=y
CONFIG_MTD_NAND_IDS=m
CONFIG_MTD_NAND_DISKONCHIP=m
# CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED is not set
CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0
# CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE is not set
CONFIG_MTD_NAND_NANDSIM=m

#
# OneNAND Flash Device Drivers
#
# CONFIG_MTD_ONENAND is not set

#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_SERIAL=m
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
CONFIG_PARPORT_PC_PCMCIA=m
CONFIG_PARPORT_NOT_PC=y
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_AX88796 is not set
CONFIG_PARPORT_1284=y

#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
CONFIG_PNPACPI=y

#
# Block devices
#
CONFIG_BLK_DEV_FD=m
CONFIG_PARIDE=m
CONFIG_PARIDE_PARPORT=m

#
# Parallel IDE high-level drivers
#
CONFIG_PARIDE_PD=m
CONFIG_PARIDE_PCD=m
CONFIG_PARIDE_PF=m
CONFIG_PARIDE_PT=m
CONFIG_PARIDE_PG=m

#
# Parallel IDE protocol modules
#
CONFIG_PARIDE_ATEN=m
CONFIG_PARIDE_BPCK=m
CONFIG_PARIDE_COMM=m
CONFIG_PARIDE_DSTR=m
CONFIG_PARIDE_FIT2=m
CONFIG_PARIDE_FIT3=m
CONFIG_PARIDE_EPAT=m
CONFIG_PARIDE_EPATC8=y
CONFIG_PARIDE_EPIA=m
CONFIG_PARIDE_FRIQ=m
CONFIG_PARIDE_FRPW=m
CONFIG_PARIDE_KBIC=m
CONFIG_PARIDE_KTTI=m
CONFIG_PARIDE_ON20=m
CONFIG_PARIDE_ON26=m
CONFIG_BLK_CPQ_DA=m
CONFIG_BLK_CPQ_CISS_DA=m
CONFIG_CISS_SCSI_TAPE=y
CONFIG_BLK_DEV_DAC960=m
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_SX8=m
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=16384
CONFIG_BLK_DEV_INITRD=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
CONFIG_VIRTIO_BLK=m

#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECS=m
CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEFLOPPY=y
CONFIG_BLK_DEV_IDESCSI=m
CONFIG_IDE_TASK_IOCTL=y

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPNP=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_AEC62XX=y
CONFIG_BLK_DEV_ALI15X3=y
# CONFIG_WDC_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
CONFIG_BLK_DEV_ATIIXP=y
CONFIG_BLK_DEV_CMD64X=y
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
CONFIG_BLK_DEV_HPT34X=y
# CONFIG_HPT34X_AUTODMA is not set
CONFIG_BLK_DEV_HPT366=y
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
CONFIG_BLK_DEV_IT821X=y
# CONFIG_BLK_DEV_NS87415 is not set
CONFIG_BLK_DEV_PDC202XX_OLD=y
# CONFIG_PDC202XX_BURST is not set
CONFIG_BLK_DEV_PDC202XX_NEW=y
CONFIG_BLK_DEV_SVWKS=y
CONFIG_BLK_DEV_SIIMAGE=y
CONFIG_BLK_DEV_SIS5513=y
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=m
CONFIG_SCSI_DMA=y
CONFIG_SCSI_NETLINK=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
CONFIG_CHR_DEV_ST=m
CONFIG_CHR_DEV_OSST=m
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_CHR_DEV_SCH=m

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y

#
# SCSI Transport
#
CONFIG_SCSI_SPI_ATTRS=m
CONFIG_SCSI_FC_ATTRS=m
CONFIG_SCSI_ISCSI_ATTRS=m
CONFIG_SCSI_ISCSI1_ATTRS=m
CONFIG_SCSI_ISCSI2_ATTRS=m
CONFIG_SCSI_SAS_ATTRS=m
CONFIG_SCSI_SAS_LIBSAS=m
CONFIG_SCSI_SAS_ATA=y
# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set

#
# SCSI low-level drivers
#
CONFIG_LIBFC=m
CONFIG_LIBFCOE=m
CONFIG_FCOE=m
CONFIG_LIBISCSI1=m
CONFIG_ISCSI_TCP=m
CONFIG_SCSI_CXGB3_ISCSI=m
CONFIG_SCSI_BNX2_ISCSI=m
CONFIG_BLK_DEV_3W_XXXX_RAID=m
CONFIG_SCSI_3W_9XXX=m
CONFIG_SCSI_ACARD=m
CONFIG_SCSI_AACRAID=m
CONFIG_SCSI_MVSAS=m
CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=4
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
CONFIG_AIC7XXX_DEBUG_MASK=0
# CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set
CONFIG_SCSI_AIC7XXX_OLD=m
CONFIG_SCSI_AIC79XX=m
CONFIG_AIC79XX_CMDS_PER_DEVICE=4
CONFIG_AIC79XX_RESET_DELAY_MS=15000
# CONFIG_AIC79XX_ENABLE_RD_STRM is not set
# CONFIG_AIC79XX_DEBUG_ENABLE is not set
CONFIG_AIC79XX_DEBUG_MASK=0
# CONFIG_AIC79XX_REG_PRETTY_PRINT is not set
CONFIG_SCSI_AIC94XX=m
# CONFIG_AIC94XX_DEBUG is not set
CONFIG_SCSI_ARCMSR=m
CONFIG_MEGARAID_NEWGEN=y
CONFIG_MEGARAID_MM=m
CONFIG_MEGARAID_MAILBOX=m
CONFIG_MEGARAID_LEGACY=m
CONFIG_MEGARAID_SAS=m
CONFIG_SCSI_MPT2SAS=m
CONFIG_SCSI_MPT2SAS_MAX_SGE=128
CONFIG_SCSI_MPT2SAS_LOGGING=y
CONFIG_SCSI_HPTIOP=m
# CONFIG_SCSI_BUSLOGIC is not set
CONFIG_FCOE_FNIC=m
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
CONFIG_SCSI_GDTH=m
CONFIG_SCSI_IPS=m
CONFIG_SCSI_INITIO=m
# CONFIG_SCSI_INIA100 is not set
CONFIG_SCSI_PPA=m
CONFIG_SCSI_IMM=m
# CONFIG_SCSI_IZIP_EPP16 is not set
# CONFIG_SCSI_IZIP_SLOW_CTR is not set
CONFIG_SCSI_STEX=m
CONFIG_SCSI_SYM53C8XX_2=m
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
CONFIG_SCSI_SYM53C8XX_MMIO=y
# CONFIG_SCSI_IPR is not set
CONFIG_SCSI_QLOGIC_1280=m
CONFIG_SCSI_QLA_FC=m
CONFIG_SCSI_QLA_ISCSI=m
CONFIG_SCSI_LPFC=m
CONFIG_SCSI_DC395x=m
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set

#
# PCMCIA SCSI adapter support
#
# CONFIG_PCMCIA_FDOMAIN is not set
# CONFIG_PCMCIA_QLOGIC is not set
# CONFIG_PCMCIA_SYM53C500 is not set
CONFIG_SCSI_DH=m
CONFIG_SCSI_DH_RDAC=m
CONFIG_SCSI_DH_ALUA=m
CONFIG_ATA=m
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_ACPI=y
CONFIG_SATA_PMP=y
CONFIG_SATA_AHCI=m
CONFIG_SATA_SIL24=m
CONFIG_ATA_SFF=y
CONFIG_SATA_SVW=m
CONFIG_ATA_PIIX=m
CONFIG_SATA_MV=m
CONFIG_SATA_NV=m
CONFIG_PDC_ADMA=m
CONFIG_SATA_QSTOR=m
CONFIG_SATA_PROMISE=m
CONFIG_SATA_SX4=m
CONFIG_SATA_SIL=m
CONFIG_SATA_SIS=m
CONFIG_SATA_ULI=m
CONFIG_SATA_VIA=m
CONFIG_SATA_VITESSE=m
CONFIG_SATA_INIC162X=m
# CONFIG_PATA_ACPI is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
CONFIG_PATA_MARVELL=m
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PCMCIA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
CONFIG_PATA_PDC2027X=m
CONFIG_PATA_SIL680=m
CONFIG_PATA_SIS=m
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
# CONFIG_PATA_SCH is not set
CONFIG_ATA_INTEL_COMBINED=y

#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
CONFIG_MD_RAID10=m
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
CONFIG_MD_MULTIPATH=m
CONFIG_MD_FAULTY=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_MULTIPATH_EMC=m
CONFIG_DM_MULTIPATH_RDAC=m
CONFIG_DM_MULTIPATH_HP=m
CONFIG_DM_RAID45=m
CONFIG_DM_UEVENT=y

#
# Fusion MPT device support
#
CONFIG_FUSION=y
CONFIG_FUSION_SPI=m
CONFIG_FUSION_FC=m
CONFIG_FUSION_SAS=m
CONFIG_FUSION_MAX_SGE=128
CONFIG_FUSION_CTL=m
CONFIG_FUSION_LAN=m
CONFIG_FUSION_LOGGING=y

#
# Enable only one of the two stacks, unless you know what you are doing
#
CONFIG_FIREWIRE=m
CONFIG_FIREWIRE_OHCI=m
CONFIG_FIREWIRE_OHCI_DEBUG=y
CONFIG_FIREWIRE_SBP2=m

#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set

#
# I2O device support
#
CONFIG_I2O=m
# CONFIG_I2O_LCT_NOTIFY_ON_CHANGES is not set
CONFIG_I2O_EXT_ADAPTEC=y
CONFIG_I2O_EXT_ADAPTEC_DMA64=y
CONFIG_I2O_CONFIG=m
CONFIG_I2O_CONFIG_OLD_IOCTL=y
CONFIG_I2O_BUS=m
CONFIG_I2O_BLOCK=m
CONFIG_I2O_SCSI=m
CONFIG_I2O_PROC=m

#
# Network device support
#
CONFIG_NETDEVICES=y
CONFIG_IFB=m
CONFIG_DUMMY=m
CONFIG_BONDING=m
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_NET_SB1000 is not set

#
# ARCnet devices
#
# CONFIG_ARCNET is not set

#
# PHY device support
#
CONFIG_PHYLIB=m

#
# MII PHY device drivers
#
CONFIG_MARVELL_PHY=m
CONFIG_DAVICOM_PHY=m
CONFIG_QSEMI_PHY=m
CONFIG_LXT_PHY=m
CONFIG_CICADA_PHY=m
CONFIG_VITESSE_PHY=m
CONFIG_SMSC_PHY=m
CONFIG_FIXED_PHY=m
CONFIG_FIXED_MII_10_FDX=y
CONFIG_FIXED_MII_100_FDX=y

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
CONFIG_HAPPYMEAL=m
CONFIG_SUNGEM=m
CONFIG_CASSINI=m
CONFIG_NET_VENDOR_3COM=y
CONFIG_VORTEX=m
CONFIG_TYPHOON=m

#
# Tulip family network device support
#
CONFIG_NET_TULIP=y
CONFIG_DE2104X=m
CONFIG_TULIP=m
# CONFIG_TULIP_MWI is not set
CONFIG_TULIP_MMIO=y
# CONFIG_TULIP_NAPI is not set
CONFIG_DE4X5=m
CONFIG_WINBOND_840=m
CONFIG_DM9102=m
CONFIG_ULI526X=m
CONFIG_PCMCIA_XIRCOM=m
# CONFIG_HP100 is not set
CONFIG_NET_PCI=y
CONFIG_PCNET32=m
CONFIG_AMD8111_ETH=m
CONFIG_AMD8111E_NAPI=y
CONFIG_ADAPTEC_STARFIRE=m
CONFIG_ADAPTEC_STARFIRE_NAPI=y
CONFIG_B44=m
CONFIG_FORCEDETH=m
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
CONFIG_E100=m
CONFIG_FEALNX=m
CONFIG_NATSEMI=m
CONFIG_NE2K_PCI=m
CONFIG_8139CP=m
CONFIG_8139TOO=m
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
CONFIG_8139TOO_8129=y
# CONFIG_8139_OLD_RX_RESET is not set
CONFIG_SIS900=m
CONFIG_EPIC100=m
CONFIG_SUNDANCE=m
# CONFIG_SUNDANCE_MMIO is not set
CONFIG_VIA_RHINE=m
CONFIG_VIA_RHINE_MMIO=y
CONFIG_VIA_RHINE_NAPI=y
CONFIG_NET_POCKET=y
# CONFIG_ATP is not set
# CONFIG_DE600 is not set
# CONFIG_DE620 is not set

#
# Ethernet (1000 Mbit)
#
CONFIG_ACENIC=m
# CONFIG_ACENIC_OMIT_TIGON_I is not set
CONFIG_DL2K=m
CONFIG_E1000=m
CONFIG_E1000_NAPI=y
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
CONFIG_E1000E=m
CONFIG_IGB=m
CONFIG_IGBVF=m
CONFIG_NS83820=m
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
CONFIG_R8169=m
CONFIG_R8169_VLAN=y
CONFIG_SIS190=m
CONFIG_SKGE=m
CONFIG_SKY2=m
# CONFIG_SK98LIN is not set
CONFIG_VIA_VELOCITY=m
CONFIG_TIGON3=m
CONFIG_BNX2=m
CONFIG_CNIC=m
CONFIG_QLA3XXX=m

#
# Ethernet (10000 Mbit)
#
CONFIG_CHELSIO_T1=m
CONFIG_CHELSIO_T3=m
CONFIG_IXGBE=m
CONFIG_IXGB=m
CONFIG_IXGB_NAPI=y
CONFIG_S2IO=m
CONFIG_S2IO_NAPI=y
CONFIG_MYRI10GE=m
CONFIG_ENIC=m
CONFIG_NETXEN_NIC=m
CONFIG_NIU=m
CONFIG_BNX2X=m
CONFIG_MLX4_EN=m
CONFIG_QLGE=m
CONFIG_MLX4_CORE=m
CONFIG_MLX4_DEBUG=y
CONFIG_BE2NET=m

#
# Token Ring devices
#
CONFIG_TR=y
CONFIG_IBMOL=m
CONFIG_3C359=m
# CONFIG_TMS380TR is not set

#
# Wireless LAN (non-hamradio)
#
CONFIG_NET_RADIO=y

#
# Obsolete Wireless cards support (pre-802.11)
#
# CONFIG_STRIP is not set
CONFIG_PCMCIA_WAVELAN=m
CONFIG_PCMCIA_NETWAVE=m

#
# Wireless 802.11 Frequency Hopping cards support
#
# CONFIG_PCMCIA_RAYCS is not set

#
# Wireless 802.11b ISA/PCI cards support
#
CONFIG_IPW2100=m
CONFIG_IPW2100_MONITOR=y
# CONFIG_IPW2100_DEBUG is not set
CONFIG_IPW2200=m
CONFIG_IPW2200_MONITOR=y
CONFIG_IPW2200_RADIOTAP=y
CONFIG_IPW2200_PROMISCUOUS=y
CONFIG_IPW2200_QOS=y
# CONFIG_IPW2200_DEBUG is not set
CONFIG_AIRO=m
CONFIG_HERMES=m
CONFIG_PLX_HERMES=m
CONFIG_TMD_HERMES=m
CONFIG_NORTEL_HERMES=m
CONFIG_PCI_HERMES=m
CONFIG_ATMEL=m
CONFIG_PCI_ATMEL=m

#
# Wireless 802.11b Pcmcia/Cardbus cards support
#
CONFIG_PCMCIA_HERMES=m
CONFIG_PCMCIA_SPECTRUM=m
CONFIG_AIRO_CS=m
CONFIG_PCMCIA_ATMEL=m
CONFIG_PCMCIA_WL3501=m

#
# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
#
CONFIG_PRISM54=m
CONFIG_USB_ZD1201=m
CONFIG_RTL8180=m
CONFIG_RTL8187=m
CONFIG_HOSTAP=m
CONFIG_HOSTAP_FIRMWARE=y
CONFIG_HOSTAP_FIRMWARE_NVRAM=y
CONFIG_HOSTAP_PLX=m
CONFIG_HOSTAP_PCI=m
CONFIG_HOSTAP_CS=m
CONFIG_BCM43XX=m
CONFIG_BCM43XX_DEBUG=y
CONFIG_BCM43XX_DMA=y
CONFIG_BCM43XX_PIO=y
CONFIG_BCM43XX_DMA_AND_PIO_MODE=y
# CONFIG_BCM43XX_DMA_MODE is not set
# CONFIG_BCM43XX_PIO_MODE is not set
CONFIG_ZD1211RW=m
# CONFIG_ZD1211RW_DEBUG is not set
CONFIG_NET_WIRELESS=y
CONFIG_ATH5K=m
# CONFIG_ATH5K_DEBUG is not set
CONFIG_IWLWIFI=m
CONFIG_IWLCORE=m
CONFIG_IWLWIFI_LEDS=y
# CONFIG_IWLWIFI_RFKILL is not set
# CONFIG_IWLWIFI_DEBUG is not set
CONFIG_IWLAGN=m
CONFIG_IWLAGN_SPECTRUM_MEASUREMENT=y
CONFIG_IWLAGN_LEDS=y
CONFIG_IWL4965=y
CONFIG_IWL5000=y
CONFIG_IWL3945=m
# CONFIG_IWL3945_RFKILL is not set
CONFIG_IWL3945_SPECTRUM_MEASUREMENT=y
CONFIG_IWL3945_LEDS=y
# CONFIG_IWL3945_DEBUG is not set
CONFIG_RT2X00=m
CONFIG_RT2X00_LIB=m
CONFIG_RT2X00_LIB_PCI=m
CONFIG_RT2X00_LIB_USB=m
CONFIG_RT2X00_LIB_FIRMWARE=y
CONFIG_RT2400PCI=m
# CONFIG_RT2400PCI_RFKILL is not set
# CONFIG_RT2400PCI_LEDS is not set
CONFIG_RT2500PCI=m
# CONFIG_RT2500PCI_RFKILL is not set
# CONFIG_RT2500PCI_LEDS is not set
CONFIG_RT61PCI=m
# CONFIG_RT61PCI_RFKILL is not set
# CONFIG_RT61PCI_LEDS is not set
CONFIG_RT2500USB=m
# CONFIG_RT2500USB_LEDS is not set
CONFIG_RT73USB=m
# CONFIG_RT73USB_LEDS is not set
# CONFIG_RT2X00_DEBUG is not set

#
# PCMCIA network device support
#
CONFIG_NET_PCMCIA=y
CONFIG_PCMCIA_3C589=m
CONFIG_PCMCIA_3C574=m
CONFIG_PCMCIA_FMVJ18X=m
CONFIG_PCMCIA_PCNET=m
CONFIG_PCMCIA_NMCLAN=m
CONFIG_PCMCIA_SMC91C92=m
CONFIG_PCMCIA_XIRC2PS=m
CONFIG_PCMCIA_AXNET=m

#
# Wan interfaces
#
# CONFIG_WAN is not set

#
# ATM drivers
#
# CONFIG_ATM_DUMMY is not set
CONFIG_ATM_TCP=m
CONFIG_ATM_LANAI=m
CONFIG_ATM_ENI=m
# CONFIG_ATM_ENI_DEBUG is not set
# CONFIG_ATM_ENI_TUNE_BURST is not set
CONFIG_ATM_FIRESTREAM=m
# CONFIG_ATM_ZATM is not set
CONFIG_ATM_IDT77252=m
# CONFIG_ATM_IDT77252_DEBUG is not set
# CONFIG_ATM_IDT77252_RCV_ALL is not set
CONFIG_ATM_IDT77252_USE_SUNI=y
CONFIG_ATM_AMBASSADOR=m
# CONFIG_ATM_AMBASSADOR_DEBUG is not set
CONFIG_ATM_HORIZON=m
# CONFIG_ATM_HORIZON_DEBUG is not set
CONFIG_ATM_FORE200E_MAYBE=m
# CONFIG_ATM_FORE200E_PCA is not set
CONFIG_ATM_HE=m
# CONFIG_ATM_HE_USE_SUNI is not set
CONFIG_FDDI=y
# CONFIG_DEFXX is not set
# CONFIG_SKFP is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
# CONFIG_PPP_BSDCOMP is not set
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
CONFIG_PPPOATM=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
# CONFIG_SLIP_MODE_SLIP6 is not set
CONFIG_NET_FC=y
# CONFIG_SHAPER is not set
CONFIG_NETCONSOLE=m
CONFIG_NETPOLL=y
# CONFIG_NETPOLL_RX is not set
CONFIG_NETPOLL_TRAP=y
CONFIG_NET_POLL_CONTROLLER=y
CONFIG_VIRTIO_NET=m

#
# ISDN subsystem
#
CONFIG_ISDN=m

#
# Old ISDN4Linux
#
CONFIG_ISDN_I4L=m
CONFIG_ISDN_PPP=y
CONFIG_ISDN_PPP_VJ=y
CONFIG_ISDN_MPP=y
CONFIG_IPPP_FILTER=y
# CONFIG_ISDN_PPP_BSDCOMP is not set
CONFIG_ISDN_AUDIO=y
CONFIG_ISDN_TTY_FAX=y

#
# ISDN feature submodules
#
CONFIG_ISDN_DIVERSION=m

#
# ISDN4Linux hardware drivers
#

#
# Passive cards
#
CONFIG_ISDN_DRV_HISAX=m

#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
CONFIG_HISAX_NO_SENDCOMPLETE=y
CONFIG_HISAX_NO_LLC=y
CONFIG_HISAX_NO_KEYPAD=y
CONFIG_HISAX_1TR6=y
CONFIG_HISAX_NI1=y
CONFIG_HISAX_MAX_CARDS=8

#
# HiSax supported cards
#
CONFIG_HISAX_16_3=y
CONFIG_HISAX_TELESPCI=y
CONFIG_HISAX_S0BOX=y
CONFIG_HISAX_FRITZPCI=y
CONFIG_HISAX_AVM_A1_PCMCIA=y
CONFIG_HISAX_ELSA=y
CONFIG_HISAX_DIEHLDIVA=y
CONFIG_HISAX_SEDLBAUER=y
CONFIG_HISAX_NETJET=y
CONFIG_HISAX_NETJET_U=y
CONFIG_HISAX_NICCY=y
CONFIG_HISAX_BKM_A4T=y
CONFIG_HISAX_SCT_QUADRO=y
CONFIG_HISAX_GAZEL=y
CONFIG_HISAX_HFC_PCI=y
CONFIG_HISAX_W6692=y
CONFIG_HISAX_HFC_SX=y
CONFIG_HISAX_ENTERNOW_PCI=y
# CONFIG_HISAX_DEBUG is not set

#
# HiSax PCMCIA card service modules
#
CONFIG_HISAX_SEDLBAUER_CS=m
CONFIG_HISAX_ELSA_CS=m
CONFIG_HISAX_AVM_A1_CS=m
CONFIG_HISAX_TELES_CS=m

#
# HiSax sub driver modules
#
CONFIG_HISAX_ST5481=m
# CONFIG_HISAX_HFCUSB is not set
CONFIG_HISAX_HFC4S8S=m
CONFIG_HISAX_FRITZ_PCIPNP=m
CONFIG_HISAX_HDLC=y

#
# Active cards
#

#
# Siemens Gigaset
#
CONFIG_ISDN_DRV_GIGASET=m
CONFIG_GIGASET_BASE=m
CONFIG_GIGASET_M105=m
# CONFIG_GIGASET_DEBUG is not set
# CONFIG_GIGASET_UNDOCREQ is not set

#
# CAPI subsystem
#
CONFIG_ISDN_CAPI=m
CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y
CONFIG_ISDN_CAPI_MIDDLEWARE=y
CONFIG_ISDN_CAPI_CAPI20=m
CONFIG_ISDN_CAPI_CAPIFS_BOOL=y
CONFIG_ISDN_CAPI_CAPIFS=m
CONFIG_ISDN_CAPI_CAPIDRV=m

#
# CAPI hardware drivers
#

#
# Active AVM cards
#
CONFIG_CAPI_AVM=y
CONFIG_ISDN_DRV_AVMB1_B1PCI=m
CONFIG_ISDN_DRV_AVMB1_B1PCIV4=y
CONFIG_ISDN_DRV_AVMB1_B1PCMCIA=m
CONFIG_ISDN_DRV_AVMB1_AVM_CS=m
CONFIG_ISDN_DRV_AVMB1_T1PCI=m
CONFIG_ISDN_DRV_AVMB1_C4=m

#
# Active Eicon DIVA Server cards
#
# CONFIG_CAPI_EICON is not set

#
# Telephony Support
#
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=m
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_SERIAL=m
CONFIG_MOUSE_VSXXXAA=m
CONFIG_INPUT_JOYSTICK=y
# CONFIG_JOYSTICK_ANALOG is not set
# CONFIG_JOYSTICK_A3D is not set
# CONFIG_JOYSTICK_ADI is not set
# CONFIG_JOYSTICK_COBRA is not set
# CONFIG_JOYSTICK_GF2K is not set
# CONFIG_JOYSTICK_GRIP is not set
# CONFIG_JOYSTICK_GRIP_MP is not set
# CONFIG_JOYSTICK_GUILLEMOT is not set
# CONFIG_JOYSTICK_INTERACT is not set
# CONFIG_JOYSTICK_SIDEWINDER is not set
# CONFIG_JOYSTICK_TMDC is not set
# CONFIG_JOYSTICK_IFORCE is not set
# CONFIG_JOYSTICK_WARRIOR is not set
# CONFIG_JOYSTICK_MAGELLAN is not set
# CONFIG_JOYSTICK_SPACEORB is not set
# CONFIG_JOYSTICK_SPACEBALL is not set
# CONFIG_JOYSTICK_STINGER is not set
CONFIG_JOYSTICK_TWIDJOY=m
# CONFIG_JOYSTICK_DB9 is not set
# CONFIG_JOYSTICK_GAMECON is not set
# CONFIG_JOYSTICK_TURBOGRAFX is not set
CONFIG_JOYSTICK_JOYDUMP=m
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_GUNZE=m
CONFIG_TOUCHSCREEN_ELO=m
CONFIG_TOUCHSCREEN_MTOUCH=m
CONFIG_TOUCHSCREEN_MK712=m
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
CONFIG_INPUT_UINPUT=m

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=m
CONFIG_GAMEPORT=m
CONFIG_GAMEPORT_NS558=m
CONFIG_GAMEPORT_L4=m
CONFIG_GAMEPORT_EMU10K1=m
CONFIG_GAMEPORT_FM801=m

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
CONFIG_CYCLADES=m
# CONFIG_CYZ_INTR is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_ISI is not set
CONFIG_SYNCLINK=m
CONFIG_SYNCLINKMP=m
CONFIG_SYNCLINK_GT=m
CONFIG_N_HDLC=m
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_PNP=y
CONFIG_SERIAL_8250_CS=m
CONFIG_SERIAL_8250_NR_UARTS=32
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_8250_RSA=y

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_JSM=m
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_CRASH=m
CONFIG_PRINTER=m
CONFIG_LP_CONSOLE=y
CONFIG_PPDEV=m
# CONFIG_TIPAR is not set

#
# IPMI
#
CONFIG_IPMI_HANDLER=m
CONFIG_IPMI_PANIC_EVENT=y
CONFIG_IPMI_PANIC_STRING=y
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m

#
# Watchdog Cards
#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set

#
# Watchdog Device Drivers
#
CONFIG_SOFT_WATCHDOG=m
# CONFIG_ACQUIRE_WDT is not set
# CONFIG_ADVANTECH_WDT is not set
CONFIG_ALIM1535_WDT=m
CONFIG_ALIM7101_WDT=m
# CONFIG_SC520_WDT is not set
# CONFIG_EUROTECH_WDT is not set
# CONFIG_IB700_WDT is not set
CONFIG_IBMASR=m
# CONFIG_WAFER_WDT is not set
CONFIG_I6300ESB_WDT=m
CONFIG_I8XX_TCO=m
# CONFIG_HP_WATCHDOG is not set
# CONFIG_SC1200_WDT is not set
# CONFIG_60XX_WDT is not set
# CONFIG_SBC8360_WDT is not set
# CONFIG_CPU5_WDT is not set
CONFIG_W83627HF_WDT=m
CONFIG_W83877F_WDT=m
CONFIG_W83977F_WDT=m
CONFIG_MACHZ_WDT=m
# CONFIG_SBC_EPX_C3_WATCHDOG is not set

#
# PCI-based Watchdog Cards
#
CONFIG_PCIPCWATCHDOG=m
CONFIG_WDTPCI=m
CONFIG_WDT_501_PCI=y

#
# USB-based Watchdog Cards
#
CONFIG_USBPCWATCHDOG=m
CONFIG_HW_RANDOM=y
CONFIG_HW_RANDOM_INTEL=m
CONFIG_HW_RANDOM_AMD=m
# CONFIG_HW_RANDOM_GEODE is not set
CONFIG_NVRAM=y
CONFIG_RTC=y
CONFIG_DTLK=m
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set

#
# Ftape, the floppy tape device driver
#
CONFIG_AGP=y
CONFIG_AGP_AMD64=y
CONFIG_AGP_INTEL=y
CONFIG_AGP_SIS=y
CONFIG_AGP_VIA=y
CONFIG_DRM=m
# CONFIG_DRM_TDFX is not set
CONFIG_DRM_R128=m
CONFIG_DRM_RADEON=m
CONFIG_DRM_I810=m
CONFIG_DRM_I830=m
CONFIG_DRM_I915=m
CONFIG_DRM_MGA=m
# CONFIG_DRM_SIS is not set
CONFIG_DRM_VIA=m
CONFIG_DRM_SAVAGE=m

#
# PCMCIA character devices
#
# CONFIG_SYNCLINK_CS is not set
CONFIG_CARDMAN_4000=m
CONFIG_CARDMAN_4040=m
# CONFIG_MWAVE is not set
CONFIG_PC8736x_GPIO=m
CONFIG_NSC_GPIO=m
CONFIG_RAW_DRIVER=y
CONFIG_MAX_RAW_DEVS=8192
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
# CONFIG_HPET_MMAP is not set
CONFIG_HANGCHECK_TIMER=m
CONFIG_TCG_TPM=m
CONFIG_TCG_TIS=m
CONFIG_TCG_NSC=m
CONFIG_TCG_ATMEL=m
CONFIG_TCG_INFINEON=m
CONFIG_TELCLOCK=m

#
# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ALGOPCA=m

#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
CONFIG_I2C_AMD756=m
CONFIG_I2C_AMD756_S4882=m
CONFIG_I2C_AMD8111=m
CONFIG_I2C_I801=m
# CONFIG_I2C_I810 is not set
CONFIG_I2C_PIIX4=m
CONFIG_I2C_ISA=m
CONFIG_I2C_NFORCE2=m
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_PARPORT=m
CONFIG_I2C_PARPORT_LIGHT=m
CONFIG_I2C_PROSAVAGE=m
CONFIG_I2C_SAVAGE4=m
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
CONFIG_I2C_SIS96X=m
CONFIG_I2C_STUB=m
CONFIG_I2C_VIA=m
CONFIG_I2C_VIAPRO=m
CONFIG_I2C_VOODOO3=m
# CONFIG_I2C_PCA_ISA is not set

#
# Miscellaneous I2C Chip support
#
CONFIG_SENSORS_DS1337=m
CONFIG_SENSORS_DS1374=m
CONFIG_SENSORS_EEPROM=m
CONFIG_SENSORS_PCF8574=m
CONFIG_SENSORS_PCA9539=m
CONFIG_SENSORS_PCF8591=m
CONFIG_SENSORS_MAX6875=m
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set

#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set

#
# Hardware Monitoring support
#
CONFIG_HWMON=m
CONFIG_HWMON_VID=m
CONFIG_SENSORS_ABITUGURU=m
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
CONFIG_SENSORS_ADM1026=m
CONFIG_SENSORS_ADM1031=m
CONFIG_SENSORS_ADM9240=m
CONFIG_SENSORS_K8TEMP=m
CONFIG_SENSORS_ASB100=m
CONFIG_SENSORS_ATXP1=m
CONFIG_SENSORS_DS1621=m
CONFIG_SENSORS_F71805F=m
CONFIG_SENSORS_FSCHER=m
CONFIG_SENSORS_FSCPOS=m
CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_GL520SM=m
CONFIG_SENSORS_IT87=m
CONFIG_SENSORS_LM63=m
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM80=m
CONFIG_SENSORS_LM83=m
CONFIG_SENSORS_LM85=m
CONFIG_SENSORS_LM87=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_LM92=m
CONFIG_SENSORS_MAX1619=m
CONFIG_SENSORS_PC87360=m
CONFIG_SENSORS_SIS5595=m
CONFIG_SENSORS_SMSC47M1=m
CONFIG_SENSORS_SMSC47M192=m
CONFIG_SENSORS_SMSC47B397=m
CONFIG_SENSORS_VIA686A=m
CONFIG_SENSORS_VT8231=m
CONFIG_SENSORS_W83781D=m
CONFIG_SENSORS_W83791D=m
CONFIG_SENSORS_W83792D=m
CONFIG_SENSORS_W83L785TS=m
CONFIG_SENSORS_W83627HF=m
CONFIG_SENSORS_W83627EHF=m
CONFIG_SENSORS_HDAPS=m
# CONFIG_HWMON_DEBUG_CHIP is not set

#
# Misc devices
#
# CONFIG_IBM_ASM is not set
CONFIG_EEPROM_93CX6=m
CONFIG_HP_ILO=m

#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m
CONFIG_VIDEO_V4L1=y
CONFIG_VIDEO_V4L1_COMPAT=y
CONFIG_VIDEO_V4L2=y

#
# Video Capture Adapters
#

#
# Video Capture Adapters
#
# CONFIG_VIDEO_ADV_DEBUG is not set
# CONFIG_VIDEO_VIVI is not set
CONFIG_VIDEO_BT848=m
CONFIG_VIDEO_SAA6588=m
# CONFIG_VIDEO_BWQCAM is not set
# CONFIG_VIDEO_CQCAM is not set
# CONFIG_VIDEO_W9966 is not set
# CONFIG_VIDEO_CPIA is not set
CONFIG_VIDEO_CPIA2=m
# CONFIG_VIDEO_SAA5246A is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_TUNER_3036 is not set
# CONFIG_VIDEO_STRADIS is not set
# CONFIG_VIDEO_ZORAN is not set
# CONFIG_VIDEO_SAA7134 is not set
# CONFIG_VIDEO_MXB is not set
# CONFIG_VIDEO_DPC is not set
# CONFIG_VIDEO_HEXIUM_ORION is not set
# CONFIG_VIDEO_HEXIUM_GEMINI is not set
# CONFIG_VIDEO_CX88 is not set

#
# Encoders and Decoders
#
CONFIG_VIDEO_MSP3400=m
CONFIG_VIDEO_CS53L32A=m
CONFIG_VIDEO_TLV320AIC23B=m
CONFIG_VIDEO_WM8775=m
CONFIG_VIDEO_WM8739=m
CONFIG_VIDEO_CX2341X=m
CONFIG_VIDEO_CX25840=m
CONFIG_VIDEO_SAA711X=m
CONFIG_VIDEO_SAA7127=m
CONFIG_VIDEO_UPD64031A=m
CONFIG_VIDEO_UPD64083=m

#
# V4L USB devices
#
CONFIG_USB_VIDEO_CLASS=m
CONFIG_VIDEO_PVRUSB2=m
CONFIG_VIDEO_PVRUSB2_24XXX=y
CONFIG_VIDEO_PVRUSB2_SYSFS=y
# CONFIG_VIDEO_PVRUSB2_DEBUGIFC is not set
CONFIG_VIDEO_EM28XX=m
CONFIG_VIDEO_USBVIDEO=m
CONFIG_USB_VICAM=m
CONFIG_USB_IBMCAM=m
CONFIG_USB_KONICAWC=m
CONFIG_USB_QUICKCAM_MESSENGER=m
CONFIG_USB_ET61X251=m
CONFIG_VIDEO_OVCAMCHIP=m
CONFIG_USB_W9968CF=m
CONFIG_USB_OV511=m
CONFIG_USB_SE401=m
CONFIG_USB_SN9C102=m
CONFIG_USB_STV680=m
CONFIG_USB_ZC0301=m
CONFIG_USB_PWC=m
# CONFIG_USB_PWC_DEBUG is not set

#
# Radio Adapters
#
# CONFIG_RADIO_GEMTEK_PCI is not set
# CONFIG_RADIO_MAXIRADIO is not set
# CONFIG_RADIO_MAESTRO is not set
CONFIG_USB_DSBR=m

#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
CONFIG_VIDEO_TUNER=m
CONFIG_VIDEO_BUF=m
CONFIG_VIDEO_BTCX=m
CONFIG_VIDEO_IR=m
CONFIG_VIDEO_TVEEPROM=m
CONFIG_USB_DABUSB=m

#
# Graphics support
#
# CONFIG_FIRMWARE_EDID is not set
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
CONFIG_FB_CIRRUS=m
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
CONFIG_FB_VGA16=m
CONFIG_FB_VESA=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=m
CONFIG_FB_NVIDIA_I2C=y
CONFIG_FB_RIVA=m
# CONFIG_FB_RIVA_I2C is not set
# CONFIG_FB_RIVA_DEBUG is not set
CONFIG_FB_INTEL=m
# CONFIG_FB_INTEL_DEBUG is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
CONFIG_FB_SAVAGE=m
CONFIG_FB_SAVAGE_I2C=y
CONFIG_FB_SAVAGE_ACCEL=y
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
CONFIG_FB_KYRO=m
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_VGACON_SOFT_SCROLLBACK=y
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=64
CONFIG_VIDEO_SELECT=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y

#
# Logo configuration
#
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_BACKLIGHT_CLASS_DEVICE=m
CONFIG_BACKLIGHT_DEVICE=y
CONFIG_LCD_CLASS_DEVICE=m
CONFIG_LCD_DEVICE=y

#
# Sound
#
CONFIG_SOUND=m

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
CONFIG_SND_DYNAMIC_MINORS=y
# CONFIG_SND_SUPPORT_OLD_API is not set
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
CONFIG_SND_VMASTER=y

#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_OPL3_LIB=m
CONFIG_SND_VX_LIB=m
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
CONFIG_SND_MTPAV=m
# CONFIG_SND_MTS64 is not set
# CONFIG_SND_SERIAL_U16550 is not set
CONFIG_SND_MPU401=m
# CONFIG_SND_PORTMAN2X4 is not set

#
# PCI devices
#
CONFIG_SND_AD1889=m
CONFIG_SND_ALS300=m
CONFIG_SND_ALS4000=m
CONFIG_SND_ALI5451=m
CONFIG_SND_ATIIXP=m
CONFIG_SND_ATIIXP_MODEM=m
CONFIG_SND_AU8810=m
CONFIG_SND_AU8820=m
CONFIG_SND_AU8830=m
CONFIG_SND_AZT3328=m
CONFIG_SND_BT87X=m
# CONFIG_SND_BT87X_OVERCLOCK is not set
CONFIG_SND_CA0106=m
CONFIG_SND_CMIPCI=m
CONFIG_SND_CS4281=m
CONFIG_SND_CS46XX=m
CONFIG_SND_CS46XX_NEW_DSP=y
CONFIG_SND_DARLA20=m
CONFIG_SND_GINA20=m
CONFIG_SND_LAYLA20=m
CONFIG_SND_DARLA24=m
CONFIG_SND_GINA24=m
CONFIG_SND_LAYLA24=m
CONFIG_SND_MONA=m
CONFIG_SND_MIA=m
CONFIG_SND_ECHO3G=m
CONFIG_SND_INDIGO=m
CONFIG_SND_INDIGOIO=m
CONFIG_SND_INDIGODJ=m
CONFIG_SND_EMU10K1=m
CONFIG_SND_EMU10K1X=m
CONFIG_SND_ENS1370=m
CONFIG_SND_ENS1371=m
CONFIG_SND_ES1938=m
CONFIG_SND_ES1968=m
CONFIG_SND_FM801=m
CONFIG_SND_FM801_TEA575X_BOOL=y
CONFIG_SND_FM801_TEA575X=m
CONFIG_SND_HDA_POWER_SAVE=y
CONFIG_SND_HDA_POWER_SAVE_DEFAULT=0
CONFIG_SND_HDA_HWDEP=y
# CONFIG_SND_HDA_RECONFIG is not set
CONFIG_SND_HDA_INPUT_BEEP=y
CONFIG_SND_HDA_GENERIC=y
CONFIG_SND_HDA_INTEL=m
CONFIG_SND_HDSP=m
CONFIG_SND_HDSPM=m
CONFIG_SND_ICE1712=m
CONFIG_SND_ICE1724=m
CONFIG_SND_INTEL8X0=m
CONFIG_SND_INTEL8X0M=m
CONFIG_SND_KORG1212=m
CONFIG_SND_MAESTRO3=m
CONFIG_SND_MIXART=m
CONFIG_SND_NM256=m
CONFIG_SND_PCXHR=m
CONFIG_SND_RIPTIDE=m
CONFIG_SND_RME32=m
CONFIG_SND_RME96=m
CONFIG_SND_RME9652=m
CONFIG_SND_SONICVIBES=m
CONFIG_SND_TRIDENT=m
CONFIG_SND_VIA82XX=m
CONFIG_SND_VIA82XX_MODEM=m
CONFIG_SND_VX222=m
CONFIG_SND_YMFPCI=m
# CONFIG_SND_AC97_POWER_SAVE is not set

#
# USB devices
#
CONFIG_SND_USB_AUDIO=m
CONFIG_SND_USB_USX2Y=m

#
# PCMCIA devices
#
# CONFIG_SND_VXPOCKET is not set
# CONFIG_SND_PDAUDIOCF is not set

#
# SoC audio support
#
# CONFIG_SND_SOC is not set

#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
CONFIG_AC97_BUS=m

#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_ISP116X_HCD=m
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_SL811_HCD=m
CONFIG_USB_SL811_CS=m

#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#

#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
CONFIG_USB_STORAGE_ALAUDA=y
# CONFIG_USB_LIBUSUAL is not set

#
# USB Input Devices
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
CONFIG_HID_FF=y
CONFIG_HID_PID=y
CONFIG_LOGITECH_FF=y
CONFIG_THRUSTMASTER_FF=y
CONFIG_USB_HIDDEV=y
CONFIG_USB_AIPTEK=m
CONFIG_USB_WACOM=m
CONFIG_USB_ACECAD=m
CONFIG_USB_KBTAB=m
CONFIG_USB_POWERMATE=m
CONFIG_USB_TOUCHSCREEN=m
CONFIG_USB_TOUCHSCREEN_EGALAX=y
CONFIG_USB_TOUCHSCREEN_PANJIT=y
CONFIG_USB_TOUCHSCREEN_3M=y
CONFIG_USB_TOUCHSCREEN_ITM=y
# CONFIG_USB_YEALINK is not set
CONFIG_USB_XPAD=m
CONFIG_USB_ATI_REMOTE=m
CONFIG_USB_ATI_REMOTE2=m
CONFIG_USB_KEYSPAN_REMOTE=m
CONFIG_USB_APPLETOUCH=m

#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m

#
# USB Network Adapters
#
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
CONFIG_USB_NET_DM9601=m
CONFIG_USB_NET_GL620A=m
CONFIG_USB_NET_NET1080=m
CONFIG_USB_NET_PLUSB=m
CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_NET_CDC_SUBSET=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_NET_ZAURUS=m
CONFIG_USB_MON=y

#
# USB port drivers
#
CONFIG_USB_USS720=m

#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRPRIME=m
CONFIG_USB_SERIAL_ARK3116=m
CONFIG_USB_SERIAL_BELKIN=m
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_CP2101=m
CONFIG_USB_SERIAL_CYPRESS_M8=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_FUNSOFT=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_GARMIN=m
CONFIG_USB_SERIAL_IPW=m
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_NAVMAN=m
CONFIG_USB_SERIAL_PL2303=m
CONFIG_USB_SERIAL_HP4X=m
CONFIG_USB_SERIAL_SAFE=m
CONFIG_USB_SERIAL_SAFE_PADDED=y
CONFIG_USB_SERIAL_SIERRAWIRELESS=m
CONFIG_USB_SERIAL_TI=m
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
CONFIG_USB_SERIAL_OPTION=m
CONFIG_USB_SERIAL_OMNINET=m
CONFIG_USB_EZUSB=y

#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI62=m
CONFIG_USB_EMI26=m
CONFIG_USB_AUERSWALD=m
CONFIG_USB_RIO500=m
CONFIG_USB_LEGOTOWER=m
CONFIG_USB_LCD=m
CONFIG_USB_LED=m
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
CONFIG_USB_PHIDGETKIT=m
CONFIG_USB_PHIDGETSERVO=m
CONFIG_USB_IDMOUSE=m
CONFIG_USB_APPLEDISPLAY=m
CONFIG_USB_SISUSBVGA=m
CONFIG_USB_SISUSBVGA_CON=y
CONFIG_USB_LD=m
CONFIG_USB_TEST=m

#
# USB DSL modem support
#
CONFIG_USB_ATM=m
CONFIG_USB_SPEEDTOUCH=m
CONFIG_USB_CXACRU=m
CONFIG_USB_UEAGLEATM=m
CONFIG_USB_XUSBATM=m

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set

#
# MMC/SD Card support
#
CONFIG_MMC=m
# CONFIG_MMC_DEBUG is not set
CONFIG_MMC_BLOCK=m
CONFIG_MMC_SDHCI=m
CONFIG_MMC_WBSD=m

#
# LED devices
#
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y

#
# LED drivers
#

#
# LED Triggers
#
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=m
CONFIG_LEDS_TRIGGER_IDE_DISK=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=m
CONFIG_INFINIBAND=m
CONFIG_INFINIBAND_USER_MAD=m
CONFIG_INFINIBAND_USER_ACCESS=m
CONFIG_INFINIBAND_USER_MEM=y
CONFIG_INFINIBAND_ADDR_TRANS=y
CONFIG_INFINIBAND_MTHCA=m
CONFIG_INFINIBAND_MTHCA_DEBUG=y
CONFIG_INFINIBAND_IPATH=m
# CONFIG_INFINIBAND_AMSO1100 is not set
CONFIG_INFINIBAND_CXGB3=m
# CONFIG_INFINIBAND_CXGB3_DEBUG is not set
CONFIG_INFINIBAND_NES=m
# CONFIG_INFINIBAND_NES_DEBUG is not set
CONFIG_MLX4_INFINIBAND=m
CONFIG_INFINIBAND_IPOIB=m
CONFIG_INFINIBAND_IPOIB_CM=y
CONFIG_INFINIBAND_IPOIB_DEBUG=y
# CONFIG_INFINIBAND_IPOIB_DEBUG_DATA is not set
CONFIG_INFINIBAND_SRP=m
CONFIG_INFINIBAND_ISER=m
CONFIG_INFINIBAND_SDP=m
CONFIG_INFINIBAND_SDP_DEBUG=y
CONFIG_INFINIBAND_SDP_DEBUG_DATA=y
CONFIG_INFINIBAND_QLGC_VNIC=m
# CONFIG_INFINIBAND_QLGC_VNIC_STATS is not set
CONFIG_INFINIBAND_MADEYE=m

#
# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
CONFIG_EDAC=y

#
# Reporting subsystems
#
# CONFIG_EDAC_DEBUG is not set
CONFIG_EDAC_MM_EDAC=m
CONFIG_EDAC_E752X=m
CONFIG_EDAC_I3000=m
CONFIG_EDAC_I5000=m
CONFIG_EDAC_I5400=m
CONFIG_EDAC_K8=m
CONFIG_EDAC_POLL=y

#
# Real Time Clock
#
CONFIG_RTC_LIB=m
CONFIG_RTC_CLASS=m

#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=m
CONFIG_RTC_INTF_PROC=m
CONFIG_RTC_INTF_DEV=m
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set

#
# RTC drivers
#
CONFIG_RTC_DRV_X1205=m
CONFIG_RTC_DRV_DS1307=m
CONFIG_RTC_DRV_DS1553=m
CONFIG_RTC_DRV_ISL1208=m
CONFIG_RTC_DRV_DS1672=m
CONFIG_RTC_DRV_DS1742=m
CONFIG_RTC_DRV_PCF8563=m
CONFIG_RTC_DRV_PCF8583=m
CONFIG_RTC_DRV_RS5C372=m
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_TEST is not set
CONFIG_RTC_DRV_V3020=m

#
# DMA Engine support
#
CONFIG_DMA_ENGINE=m

#
# DMA Devices
#
CONFIG_INTEL_IOATDMA=m
CONFIG_DCA=m

#
# DMA Engine support version 3
#
CONFIG_DMA_ENGINE_V3=y

#
# DMA Clients V3
#
CONFIG_NET_DMA=y

#
# DMA Devices
#
CONFIG_INTEL_IOATDMA_V3=m
CONFIG_UIO=m

#
# Firmware Drivers
#
CONFIG_EDD=m
CONFIG_DELL_RBU=m
CONFIG_DCDBAS=m
CONFIG_ISCSI_IBFT_FIND=y
CONFIG_ISCSI_IBFT=m

#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
CONFIG_EXT3_FS=m
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_EXT4_FS=m
CONFIG_EXT4DEV_COMPAT=y
CONFIG_EXT4_FS_XATTR=y
CONFIG_EXT4_FS_POSIX_ACL=y
CONFIG_EXT4_FS_SECURITY=y
CONFIG_JBD=m
# CONFIG_JBD_DEBUG is not set
CONFIG_JBD2=m
# CONFIG_JBD2_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
CONFIG_XFS_QUOTA=y
CONFIG_XFS_POSIX_ACL=y
# CONFIG_XFS_RT is not set
# CONFIG_XFS_DEBUG is not set
CONFIG_GFS2_FS=m
CONFIG_GFS2_FS_LOCKING_NOLOCK=m
CONFIG_GFS2_FS_LOCKING_DLM=m
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
CONFIG_QUOTA=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m

#
# Caches
#
CONFIG_FSCACHE=m

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
CONFIG_CACHEFILES=m
CONFIG_CACHEFILES_DEBUG=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
# CONFIG_NTFS_FS is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_VMCORE=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
CONFIG_RAMFS=y
CONFIG_CONFIGFS_FS=m

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
CONFIG_ECRYPT_FS=m
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
CONFIG_JFFS2_FS=m
CONFIG_JFFS2_FS_DEBUG=0
CONFIG_JFFS2_FS_WRITEBUFFER=y
CONFIG_JFFS2_SUMMARY=y
# CONFIG_JFFS2_FS_XATTR is not set
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
# CONFIG_SQUASHFS_EMBEDDED is not set
CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3
# CONFIG_SQUASHFS_VMALLOC is not set
CONFIG_VXFS_FS=m
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_NFS_FSCACHE=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_ACL_SUPPORT=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_RPCSEC_GSS_KRB5=m
CONFIG_RPCSEC_GSS_SPKM3=m
# CONFIG_SMB_FS is not set
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
CONFIG_CIFS_WEAK_PW_HASH=y
CONFIG_CIFS_XATTR=y
CONFIG_CIFS_POSIX=y
# CONFIG_CIFS_DEBUG2 is not set
CONFIG_CIFS_EXPERIMENTAL=y
CONFIG_CIFS_UPCALL=y
CONFIG_CIFS_DFS_UPCALL=y
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
CONFIG_OSF_PARTITION=y
CONFIG_AMIGA_PARTITION=y
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
CONFIG_MINIX_SUBPARTITION=y
CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_UNIXWARE_DISKLABEL=y
# CONFIG_LDM_PARTITION is not set
CONFIG_SGI_PARTITION=y
# CONFIG_ULTRIX_PARTITION is not set
CONFIG_SUN_PARTITION=y
CONFIG_KARMA_PARTITION=y
CONFIG_EFI_PARTITION=y

#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m

#
# Distributed Lock Manager
#
CONFIG_DLM=m
CONFIG_DLM_DEBUG=y

#
# Instrumentation Support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
CONFIG_KPROBES=y

#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_DETECT_SOFTLOCKUP=y
CONFIG_SCHEDSTATS=y
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_FS=y
# CONFIG_DEBUG_VM is not set
CONFIG_DEBUG_LIST=y
# CONFIG_FRAME_POINTER is not set
# CONFIG_FORCED_INLINING is not set
CONFIG_BOOT_DELAY=y
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_SAMPLES=y
CONFIG_SAMPLE_MARKERS=m
CONFIG_SAMPLE_TRACEPOINTS=m
CONFIG_DEBUG_RODATA=y
# CONFIG_IOMMU_DEBUG is not set
CONFIG_DEBUG_STACKOVERFLOW=y
# CONFIG_DEBUG_STACK_USAGE is not set

#
# Security options
#
CONFIG_KEYS=y
CONFIG_KEYS_DEBUG_PROC_KEYS=y
CONFIG_SECURITY=y
CONFIG_SECURITY_NETWORK=y
CONFIG_SECURITY_NETWORK_XFRM=y
CONFIG_SECURITY_CAPABILITIES=y
# CONFIG_SECURITY_ROOTPLUG is not set
# CONFIG_SECURITY_SECLVL is not set
CONFIG_SECURITY_SELINUX=y
CONFIG_SECURITY_SELINUX_BOOTPARAM=y
CONFIG_SECURITY_SELINUX_BOOTPARAM_VALUE=1
CONFIG_SECURITY_SELINUX_DISABLE=y
CONFIG_SECURITY_SELINUX_DEVELOP=y
CONFIG_SECURITY_SELINUX_AVC_STATS=y
CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE=1
CONFIG_SECURITY_SELINUX_ENABLE_SECMARK_DEFAULT=y
# CONFIG_SECURITY_SELINUX_POLICYDB_VERSION_MAX is not set

#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_API=m
CONFIG_CRYPTO_FIPS=y
CONFIG_CRYPTO_ALGAPI=m
CONFIG_CRYPTO_AEAD=m
CONFIG_CRYPTO_BLKCIPHER=m
CONFIG_CRYPTO_SEQIV=m
CONFIG_CRYPTO_HASH=m
CONFIG_CRYPTO_RNG=m
CONFIG_CRYPTO_MANAGER=m
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NHMAC=m
CONFIG_CRYPTO_XCBC=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_SHA1=y
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=m
CONFIG_CRYPTO_CTR=m
CONFIG_CRYPTO_CCM=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_AES_X86_64=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=y
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_AUTHENC=m
CONFIG_CRYPTO_SIGNATURE=y
CONFIG_CRYPTO_SIGNATURE_DSA=y
CONFIG_CRYPTO_MPILIB=y

#
# Random Number Generation
#
CONFIG_CRYPTO_ANSI_CPRNG=m

#
# Hardware crypto devices
#
CONFIG_XEN_BLKDEV_FRONTEND=m
CONFIG_XEN_NETDEV_FRONTEND=m

#
# Xen PV-ON-HVM Configuration
#
CONFIG_XEN_PV_ON_HVM=y

#
# Library routines
#
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_GENERIC_ALLOCATOR=y
CONFIG_REED_SOLOMON=m
CONFIG_REED_SOLOMON_DEC16=y
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y

[-- Attachment #3: lspci --]
[-- Type: text/plain, Size: 13040 bytes --]

00:00.0 Host bridge: Intel Corporation Clarkdake DRAM Controller (rev 12)
	Subsystem: Hewlett-Packard Company Unknown device 170b
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Capabilities: [e0] Vendor Specific Information

00:02.0 VGA compatible controller: Intel Corporation Clarkdale Integrated Graphics Controller (rev 12) (prog-if 00 [VGA controller])
	Subsystem: Hewlett-Packard Company Unknown device 170b
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin A routed to IRQ 3
	Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=4M]
	Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
	Region 4: I/O ports at 1160 [size=8]
	Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
		Address: 00000000  Data: 0000
	Capabilities: [d0] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [a4] #13 [0306]

00:16.0 Communication controller: Intel Corporation Ibex Peak HECI Controller (rev 06)
	Subsystem: Hewlett-Packard Company Unknown device 170b
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin A routed to IRQ 3
	Region 0: Memory at e0429000 (64-bit, non-prefetchable) [size=16]
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [8c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
		Address: 0000000000000000  Data: 0000

00:19.0 Ethernet controller: Intel Corporation 82578DM Gigabit Network Connection (rev 06)
	Subsystem: Hewlett-Packard Company Unknown device 170b
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin B routed to IRQ 74
	Region 0: Memory at e0400000 (32-bit, non-prefetchable) [size=128K]
	Region 1: Memory at e0424000 (32-bit, non-prefetchable) [size=4K]
	Region 2: I/O ports at 1100 [size=32]
	Capabilities: [c8] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=1 PME-
	Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
		Address: 00000000fee04000  Data: 404a
	Capabilities: [e0] #13 [0306]

00:1a.0 USB Controller: Intel Corporation Ibex Peak USB2 Enhanced Host Controller (rev 06) (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company Unknown device 170b
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin A routed to IRQ 169
	Region 0: Memory at e0426000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Debug port
	Capabilities: [98] #13 [0306]

00:1b.0 Audio device: Intel Corporation Ibex Peak High Definition Audio (rev 06)
	Subsystem: Hewlett-Packard Company Unknown device 170b
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 58
	Region 0: Memory at e0420000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
		Address: 0000000000000000  Data: 0000
	Capabilities: [70] Express Unknown type IRQ 0
		Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <64ns, L1 <1us
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
		Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
		Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
		Link: Latency L0s <64ns, L1 <1us
		Link: ASPM Disabled CommClk- ExtSynch-
		Link: Speed unknown, Width x0
	Capabilities: [100] Virtual Channel
	Capabilities: [130] Unknown (5)

00:1c.0 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 1 (rev 06) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=18, subordinate=18, sec-latency=0
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: fff00000-000fffff
	Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [40] Express Root Port (Slot+) IRQ 0
		Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <64ns, L1 <1us
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
		Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
		Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 1
		Link: Latency L0s <1us, L1 <4us
		Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
		Link: Speed 2.5Gb/s, Width x0
		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
		Slot: Number 0, PowerLimit 0.000000
		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
		Slot: AttnInd Unknown, PwrInd Unknown, Power-
		Root: Correctable- Non-Fatal- Fatal- PME-
	Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
		Address: fee00000  Data: 40c1
	Capabilities: [90] #0d [0000]
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1c.4 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 5 (rev 06) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=24, subordinate=24, sec-latency=0
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: fff00000-000fffff
	Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [40] Express Root Port (Slot+) IRQ 0
		Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <64ns, L1 <1us
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
		Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
		Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
		Link: Latency L0s <1us, L1 <4us
		Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
		Link: Speed 2.5Gb/s, Width x0
		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
		Slot: Number 0, PowerLimit 0.000000
		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
		Slot: AttnInd Unknown, PwrInd Unknown, Power-
		Root: Correctable- Non-Fatal- Fatal- PME-
	Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
		Address: fee00000  Data: 40c9
	Capabilities: [90] #0d [0000]
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1c.6 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 7 (rev 06) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=30, subordinate=30, sec-latency=0
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: fff00000-000fffff
	Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [40] Express Root Port (Slot+) IRQ 0
		Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <64ns, L1 <1us
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
		Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
		Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 7
		Link: Latency L0s <1us, L1 <4us
		Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
		Link: Speed 2.5Gb/s, Width x0
		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
		Slot: Number 0, PowerLimit 0.000000
		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
		Slot: AttnInd Unknown, PwrInd Unknown, Power-
		Root: Correctable- Non-Fatal- Fatal- PME-
	Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
		Address: fee00000  Data: 40d1
	Capabilities: [90] #0d [0000]
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1d.0 USB Controller: Intel Corporation Ibex Peak USB2 Enhanced Host Controller (rev 06) (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company Unknown device 170b
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin A routed to IRQ 169
	Region 0: Memory at e0427000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Debug port
	Capabilities: [98] #13 [0306]

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Bus: primary=00, secondary=10, subordinate=10, sec-latency=32
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: fff00000-000fffff
	Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [50] #0d [0000]

00:1f.0 ISA bridge: Intel Corporation Ibex Peak LPC Interface Controller (rev 06)
	Subsystem: Hewlett-Packard Company Unknown device 170b
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Capabilities: [e0] Vendor Specific Information

00:1f.2 RAID bus controller: Intel Corporation 82801 SATA RAID Controller (rev 06)
	Subsystem: Hewlett-Packard Company Unknown device 170b
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin B routed to IRQ 225
	Region 0: I/O ports at 1168 [size=8]
	Region 1: I/O ports at 1178 [size=4]
	Region 2: I/O ports at 1170 [size=8]
	Region 3: I/O ports at 117c [size=4]
	Region 4: I/O ports at 1120 [size=32]
	Region 5: Memory at e0425000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
		Address: fee04000  Data: 40e1
	Capabilities: [70] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [a8] #12 [0010]
	Capabilities: [b0] #13 [0306]


[-- Attachment #4: ethtool-d --]
[-- Type: text/plain, Size: 462 bytes --]

Offset	Values
--------	-----
000:	 40 02 10 08 83 06 08 00 02 80 00 04 00 10 00 00
010:	 94 00 00 00 92 00 00 00 00 00 00 00 fa f0 03 31
020:	 00 10 00 00 ff 00 00 00 ff 00 00 00 08 00 00 00
030:	 09 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
040:	 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
050:	 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
060:	 00 81 00 00 00 81 00 00 00 00 00 00 00 00 00 00
070:	 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00


[-- Attachment #5: ethtool-e --]
[-- Type: text/plain, Size: 14622 bytes --]

Offset		Values
------		------
0x0000		00 1a 4b 0c 69 9a 00 08 ff ff a2 00 ff ff ff ff 
0x0010		ff ff ff ff c3 10 0b 17 3c 10 ef 10 00 00 00 00 
0x0020		01 08 00 00 00 00 05 a5 28 30 00 05 00 00 00 8d 
0x0030		f4 18 40 2b 43 00 00 00 ef 10 ad ba ef 10 f0 10 
0x0040		ad ba ad ba ad ba ad ba 00 80 90 80 00 4e 00 00 
0x0050		00 00 00 00 00 00 00 00 00 00 00 00 00 00 ff ff 
0x0060		c0 00 00 40 23 13 07 40 ff ff ff ff ff ff ff ff 
0x0070		ff ff ff ff ff ff ff ff ff ff 00 01 ff ff 2d 39 
0x0080		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0090		00 00 00 00 00 00 ff ff ff ff ff ff ff ff ff ff 
0x00a0		40 60 1f 00 04 d0 11 00 3f 01 12 00 00 00 1f 00 
0x00b0		62 00 30 00 ff ff ff ff ff ff ff ff ff ff ff ff 
0x00c0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x00d0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x00e0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x00f0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0100		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0110		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0120		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0130		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0140		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0150		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0160		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0170		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0180		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0190		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x01a0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x01b0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x01c0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x01d0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x01e0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x01f0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0200		69 53 84 03 01 00 00 00 00 00 00 00 00 00 00 00 
0x0210		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0220		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0230		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0240		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0250		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0260		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0270		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0280		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0290		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x02a0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x02b0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x02c0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x02d0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x02e0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x02f0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0300		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0310		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0320		00 00 00 00 00 00 00 00 03 3d 00 00 00 00 00 00 
0x0330		00 00 00 00 00 00 00 00 00 00 00 00 bc 0c 00 00 
0x0340		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0350		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0360		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0370		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0380		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0390		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x03a0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x03b0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x03c0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x03d0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x03e0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x03f0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0400		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0410		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0420		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0430		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0440		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0450		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0460		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0470		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0480		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0490		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x04a0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x04b0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x04c0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x04d0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x04e0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x04f0		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0500		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0510		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0520		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0530		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0540		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0550		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0560		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0570		00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
0x0580		00 00 00 00 ff ff ff ff ff ff ff ff ff ff ff ff 
0x0590		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x05a0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x05b0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x05c0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x05d0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x05e0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x05f0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0600		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0610		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0620		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0630		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0640		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0650		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0660		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0670		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0680		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0690		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x06a0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x06b0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x06c0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x06d0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x06e0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x06f0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0700		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0710		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0720		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0730		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0740		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0750		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0760		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0770		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0780		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0790		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x07a0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x07b0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x07c0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x07d0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x07e0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x07f0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0800		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0810		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0820		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0830		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0840		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0850		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0860		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0870		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0880		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0890		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x08a0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x08b0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x08c0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x08d0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x08e0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x08f0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0900		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0910		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0920		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0930		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0940		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0950		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0960		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0970		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0980		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0990		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x09a0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x09b0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x09c0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x09d0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x09e0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x09f0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0a00		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0a10		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0a20		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0a30		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0a40		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0a50		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0a60		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0a70		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0a80		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0a90		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0aa0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ab0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ac0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ad0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ae0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0af0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0b00		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0b10		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0b20		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0b30		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0b40		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0b50		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0b60		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0b70		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0b80		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0b90		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ba0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0bb0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0bc0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0bd0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0be0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0bf0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0c00		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0c10		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0c20		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0c30		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0c40		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0c50		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0c60		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0c70		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0c80		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0c90		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ca0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0cb0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0cc0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0cd0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ce0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0cf0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0d00		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0d10		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0d20		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0d30		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0d40		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0d50		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0d60		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0d70		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0d80		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0d90		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0da0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0db0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0dc0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0dd0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0de0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0df0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0e00		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0e10		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0e20		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0e30		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0e40		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0e50		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0e60		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0e70		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0e80		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0e90		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ea0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0eb0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ec0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ed0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ee0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ef0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0f00		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0f10		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0f20		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0f30		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0f40		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0f50		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0f60		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0f70		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0f80		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0f90		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0fa0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0fb0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0fc0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0fd0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0fe0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
0x0ff0		ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 

RE: [PATCH 0/3] increase skb size to prevent dma over skb boundary

[Tantilov, Emil S]

[-- Attachment #1: Type: text/plain, Size: 4913 bytes --]

Neil Horman wrote:
> On Tue, Dec 08, 2009 at 04:37:39PM -0700, Tantilov, Emil S wrote:
>> Neil Horman wrote:
>>> Hey all-
>>> 	I was tracking down a memory corruptor lately in which, with
>>> DEBUG_SLAB enabled we were getting several redzone violoations,
>>> which was always followed by an oops in the rx receive path when
>>> using the e1000e driver.  Looking at the cores, the slabs that had
>>> their redzone violated were always adjacent to a size-2048 slab
>>> which was allocated by __netdev_alloc_skb.  Doing some
>>> instrumentation led me to see the following.  When the e1000e
>>> driver sets up its rctl register, which defines the length of each
>>> of the buffers in the rx ring, we do this: 
>>> 
>>> switch (adapter->rx_buffer_len) {
>>>         case 256:
>>>                 rctl |= E1000_RCTL_SZ_256;
>>>                 rctl &= ~E1000_RCTL_BSEX;
>>>                 break;
>>>         case 512:
>>>                 rctl |= E1000_RCTL_SZ_512;
>>>                 rctl &= ~E1000_RCTL_BSEX;
>>>                 break;
>>>         case 1024:
>>>                 rctl |= E1000_RCTL_SZ_1024;
>>>                 rctl &= ~E1000_RCTL_BSEX;
>>>                 break;
>>>         case 2048:
>>>         default:
>>>                 rctl |= E1000_RCTL_SZ_2048;
>>>                 rctl &= ~E1000_RCTL_BSEX;
>>>                 break;
>>>         case 4096:
>>>                 rctl |= E1000_RCTL_SZ_4096;
>>>                 break;
>>>         case 8192:
>>>                 rctl |= E1000_RCTL_SZ_8192;
>>>                 break;
>>>         case 16384:
>>>                 rctl |= E1000_RCTL_SZ_16384;
>>>                 break;
>>>         }
>>> }
>>> 
>>> This is problematic since rx_buffer_len is set to 1500, which causes
>>> the rctl value to fall into the default case, which configures the
>>> hardware to think it can dma up to 2048 bytes into each buffer,
>>> despite the fact that the buffer is only 1500 bytes long.  If we
>>> receive a frame that is longer than 1500 bytes, then the dma will
>>> overrun the 1500 byte limit of the sk_buff's data block spilling
>>> into the skb_shared_info structure (which is placed immediately
>>> after the end of the skb->end pointer (or at skb->head + skb->end if
>>> NET_SKBUFF_DATA_USES_OFFSET is configured).  In either case, the
>>> spillover corrupts the skb_shared_info structure, and sets us up for
>>> any number of subsequent corruptions/oopses/failures.  I've fixed
>>> this by normalizing the rx_buffer_length value in the setup_rctl
>>> function, which rounds up the length to the configured value of
>>> rctl, forcing us to allocate buffers of a size that meet the
>>> hardwares configuration needs. 
>>> 
>>> I've tested this on e1000e and confirmed that it fixes my redzone
>>> violations and the observed oops.  Visual inspection indicates that
>>> e1000 and ixgb also need this fix.  I've not explicitly tested them
>>> though, so I've split this into three separate patches
>>> 
>>> Regards
>>> Neil
>>> 
>>> Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
>> 
>> Hi Neil,
>> 
>> I am trying to test the patches you submitted (thanks btw) and so
>> far am not able to reproduce the panic you described. When MTU is at
>> 1500 RCTL.LPE (bit 5) is set to 0 and the HW will not allow the
>> reception of large packets (>1522 bytes, which is what rx_buffer_len
>> is set to). This is basically what I am seeing in my tests - packets
>> are discarded by the HW.     
>> 
>> Can you provide more details about the setup you used? Steps to
>> reproduce and also details (lspci -vvv, ethtool -e, ethtool -d) of
>> the HW you used and kernel config should help as well.  
>> 
>> Thanks,
>> Emil--
>> To unsubscribe from this list: send the line "unsubscribe netdev" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>> 
> 
> 
> Heres the data you asked for.  The config isn't exact, as the system
> in question was installed a few times over since I worked on this,
> but it should be very close.  The only differnce I see on this config
> is that CONFIG_SLAB_DEBUG is turned on.  Everything else should be
> identical 

Thanks for the data. Your config could not apply on my kernel (net-next-2.6 master branch). So I attached the one I used for testing in case you see anything that is different. I made sure DEBUG_SLAB is enabled.

Is this the connectathon suite you were talking about:
http://www.connectathon.org/nfstests.html

I ran overnight stress (1000 iterations of the suite)  plus some netperf stress and so far no signs of issues on a z-200 platform. 

BTW the HP z-200 is still in pre-production stage. Looking at the eeprom you provided it seems older than what we have. You should probably look into getting an updated FW.

Thanks,
Emil


[-- Attachment #2: config --]
[-- Type: application/octet-stream, Size: 48252 bytes --]

#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.32
# Wed Dec  9 16:55:58 2009
#
CONFIG_64BIT=y
# CONFIG_X86_32 is not set
CONFIG_X86_64=y
CONFIG_X86=y
CONFIG_OUTPUT_FORMAT="elf64-x86-64"
CONFIG_ARCH_DEFCONFIG="arch/x86/configs/x86_64_defconfig"
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_ARCH_HAS_CPU_RELAX=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y
CONFIG_HAVE_SETUP_PER_CPU_AREA=y
CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK=y
CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK=y
CONFIG_HAVE_CPUMASK_OF_CPU_MAP=y
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ZONE_DMA32=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_AUDIT_ARCH=y
CONFIG_ARCH_SUPPORTS_OPTIMIZED_INLINING=y
CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_USE_GENERIC_SMP_HELPERS=y
CONFIG_X86_64_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_TRAMPOLINE=y
# CONFIG_KTIME_SCALAR is not set
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_CONSTRUCTORS=y

#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION="-net-next-master-120909"
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_HAVE_KERNEL_GZIP=y
CONFIG_HAVE_KERNEL_BZIP2=y
CONFIG_HAVE_KERNEL_LZMA=y
CONFIG_KERNEL_GZIP=y
# CONFIG_KERNEL_BZIP2 is not set
# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_POSIX_MQUEUE_SYSCTL=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set

#
# RCU Subsystem
#
CONFIG_TREE_RCU=y
# CONFIG_TREE_PREEMPT_RCU is not set
# CONFIG_TINY_RCU is not set
# CONFIG_RCU_TRACE is not set
CONFIG_RCU_FANOUT=64
# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=18
CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y
# CONFIG_GROUP_SCHED is not set
# CONFIG_CGROUPS is not set
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_RELAY=y
CONFIG_NAMESPACES=y
# CONFIG_UTS_NS is not set
# CONFIG_IPC_NS is not set
# CONFIG_USER_NS is not set
# CONFIG_PID_NS is not set
# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_RD_GZIP=y
CONFIG_RD_BZIP2=y
CONFIG_RD_LZMA=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_PCSPKR_PLATFORM=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
CONFIG_HAVE_PERF_EVENTS=y

#
# Kernel Performance Events And Counters
#
CONFIG_PERF_EVENTS=y
CONFIG_EVENT_PROFILE=y
CONFIG_PERF_COUNTERS=y
# CONFIG_DEBUG_PERF_USE_VMALLOC is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
CONFIG_OPROFILE=y
# CONFIG_OPROFILE_IBS is not set
# CONFIG_OPROFILE_EVENT_MULTIPLEX is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_KPROBES=y
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
CONFIG_KRETPROBES=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_HW_BREAKPOINT=y
CONFIG_HAVE_USER_RETURN_NOTIFIER=y

#
# GCOV-based kernel profiling
#
# CONFIG_GCOV_KERNEL is not set
CONFIG_SLOW_WORK=y
# CONFIG_SLOW_WORK_DEBUG is not set
# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
CONFIG_BLOCK_COMPAT=y

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
# CONFIG_INLINE_SPIN_TRYLOCK is not set
# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
# CONFIG_INLINE_SPIN_LOCK is not set
# CONFIG_INLINE_SPIN_LOCK_BH is not set
# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
# CONFIG_INLINE_SPIN_UNLOCK is not set
# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
# CONFIG_INLINE_SPIN_UNLOCK_IRQ is not set
# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
# CONFIG_INLINE_READ_TRYLOCK is not set
# CONFIG_INLINE_READ_LOCK is not set
# CONFIG_INLINE_READ_LOCK_BH is not set
# CONFIG_INLINE_READ_LOCK_IRQ is not set
# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
# CONFIG_INLINE_READ_UNLOCK is not set
# CONFIG_INLINE_READ_UNLOCK_BH is not set
# CONFIG_INLINE_READ_UNLOCK_IRQ is not set
# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
# CONFIG_INLINE_WRITE_TRYLOCK is not set
# CONFIG_INLINE_WRITE_LOCK is not set
# CONFIG_INLINE_WRITE_LOCK_BH is not set
# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
# CONFIG_INLINE_WRITE_UNLOCK is not set
# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
# CONFIG_INLINE_WRITE_UNLOCK_IRQ is not set
# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
CONFIG_MUTEX_SPIN_ON_OWNER=y
CONFIG_FREEZER=y

#
# Processor type and features
#
# CONFIG_NO_HZ is not set
# CONFIG_HIGH_RES_TIMERS is not set
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_SMP=y
# CONFIG_SPARSE_IRQ is not set
CONFIG_X86_MPPARSE=y
CONFIG_X86_EXTENDED_PLATFORM=y
# CONFIG_X86_VSMP is not set
CONFIG_X86_SUPPORTS_MEMORY_FAILURE=y
CONFIG_SCHED_OMIT_FRAME_POINTER=y
# CONFIG_PARAVIRT_GUEST is not set
# CONFIG_MEMTEST is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_MVIAC7 is not set
# CONFIG_MPSC is not set
CONFIG_MCORE2=y
# CONFIG_MATOM is not set
# CONFIG_GENERIC_CPU is not set
CONFIG_X86_CPU=y
CONFIG_X86_L1_CACHE_BYTES=64
CONFIG_X86_INTERNODE_CACHE_BYTES=64
CONFIG_X86_CMPXCHG=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_P6_NOP=y
CONFIG_X86_TSC=y
CONFIG_X86_CMPXCHG64=y
CONFIG_X86_CMOV=y
CONFIG_X86_MINIMUM_CPU_FAMILY=64
CONFIG_X86_DEBUGCTLMSR=y
CONFIG_CPU_SUP_INTEL=y
CONFIG_CPU_SUP_AMD=y
CONFIG_CPU_SUP_CENTAUR=y
# CONFIG_X86_DS is not set
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_DMI=y
CONFIG_GART_IOMMU=y
# CONFIG_CALGARY_IOMMU is not set
# CONFIG_AMD_IOMMU is not set
CONFIG_SWIOTLB=y
CONFIG_IOMMU_HELPER=y
# CONFIG_IOMMU_API is not set
# CONFIG_MAXSMP is not set
CONFIG_NR_CPUS=64
CONFIG_SCHED_SMT=y
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
# CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS is not set
CONFIG_X86_MCE=y
CONFIG_X86_MCE_INTEL=y
CONFIG_X86_MCE_AMD=y
CONFIG_X86_MCE_THRESHOLD=y
# CONFIG_X86_MCE_INJECT is not set
CONFIG_X86_THERMAL_VECTOR=y
# CONFIG_I8K is not set
# CONFIG_MICROCODE is not set
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
# CONFIG_X86_CPU_DEBUG is not set
CONFIG_ARCH_PHYS_ADDR_T_64BIT=y
CONFIG_DIRECT_GBPAGES=y
# CONFIG_NUMA is not set
CONFIG_ARCH_PROC_KCORE_TEXT=y
CONFIG_ARCH_SPARSEMEM_DEFAULT=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_SELECT_MEMORY_MODEL=y
# CONFIG_FLATMEM_MANUAL is not set
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_SPARSEMEM_MANUAL=y
CONFIG_SPARSEMEM=y
CONFIG_HAVE_MEMORY_PRESENT=y
CONFIG_SPARSEMEM_EXTREME=y
CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
CONFIG_SPARSEMEM_VMEMMAP=y
# CONFIG_MEMORY_HOTPLUG is not set
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_PHYS_ADDR_T_64BIT=y
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_ARCH_SUPPORTS_MEMORY_FAILURE=y
# CONFIG_MEMORY_FAILURE is not set
# CONFIG_X86_CHECK_BIOS_CORRUPTION is not set
CONFIG_X86_RESERVE_LOW_64K=y
CONFIG_MTRR=y
# CONFIG_MTRR_SANITIZER is not set
# CONFIG_X86_PAT is not set
# CONFIG_EFI is not set
CONFIG_SECCOMP=y
# CONFIG_CC_STACKPROTECTOR is not set
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
# CONFIG_SCHED_HRTICK is not set
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x1000000
# CONFIG_RELOCATABLE is not set
CONFIG_PHYSICAL_ALIGN=0x1000000
CONFIG_HOTPLUG_CPU=y
CONFIG_COMPAT_VDSO=y
# CONFIG_CMDLINE_BOOL is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y

#
# Power management and ACPI options
#
CONFIG_ARCH_HIBERNATION_HEADER=y
CONFIG_PM=y
# CONFIG_PM_DEBUG is not set
CONFIG_PM_SLEEP_SMP=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
CONFIG_HIBERNATION_NVS=y
CONFIG_HIBERNATION=y
CONFIG_PM_STD_PARTITION=""
# CONFIG_PM_RUNTIME is not set
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_PROCFS=y
CONFIG_ACPI_PROCFS_POWER=y
CONFIG_ACPI_SYSFS_POWER=y
CONFIG_ACPI_PROC_EVENT=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_DOCK=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_HOTPLUG_CPU=y
# CONFIG_ACPI_PROCESSOR_AGGREGATOR is not set
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_CUSTOM_DSDT is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
# CONFIG_ACPI_PCI_SLOT is not set
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=y
# CONFIG_ACPI_SBS is not set
# CONFIG_SFI is not set

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
CONFIG_CPU_FREQ_DEBUG=y
CONFIG_CPU_FREQ_STAT=y
# CONFIG_CPU_FREQ_STAT_DETAILS is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y

#
# CPUFreq processor drivers
#
CONFIG_X86_ACPI_CPUFREQ=y
CONFIG_X86_POWERNOW_K8=y
# CONFIG_X86_SPEEDSTEP_CENTRINO is not set
# CONFIG_X86_P4_CLOCKMOD is not set

#
# shared options
#
# CONFIG_X86_SPEEDSTEP_LIB is not set
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y

#
# Memory power savings
#
# CONFIG_I7300_IDLE is not set

#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_DOMAINS=y
# CONFIG_DMAR is not set
# CONFIG_INTR_REMAP is not set
CONFIG_PCIEPORTBUS=y
CONFIG_PCIEAER=y
# CONFIG_PCIE_ECRC is not set
# CONFIG_PCIEAER_INJECT is not set
# CONFIG_PCIEASPM is not set
CONFIG_ARCH_SUPPORTS_MSI=y
CONFIG_PCI_MSI=y
CONFIG_PCI_LEGACY=y
# CONFIG_PCI_DEBUG is not set
# CONFIG_PCI_STUB is not set
# CONFIG_HT_IRQ is not set
# CONFIG_PCI_IOV is not set
CONFIG_ISA_DMA_API=y
CONFIG_K8_NB=y
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set

#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
CONFIG_COMPAT_BINFMT_ELF=y
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
# CONFIG_HAVE_AOUT is not set
# CONFIG_BINFMT_MISC is not set
CONFIG_IA32_EMULATION=y
CONFIG_IA32_AOUT=y
CONFIG_COMPAT=y
CONFIG_COMPAT_FOR_U64_ALIGNMENT=y
CONFIG_SYSVIPC_COMPAT=y
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
# CONFIG_XFRM_STATISTICS is not set
CONFIG_XFRM_IPCOMP=m
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
# CONFIG_IP_PNP_BOOTP is not set
# CONFIG_IP_PNP_RARP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
CONFIG_INET_TUNNEL=m
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
CONFIG_INET_LRO=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
CONFIG_IPV6=y
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
CONFIG_IPV6_ROUTE_INFO=y
CONFIG_IPV6_OPTIMISTIC_DAD=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_IPV6_MIP6=m
CONFIG_INET6_XFRM_TUNNEL=m
CONFIG_INET6_TUNNEL=m
CONFIG_INET6_XFRM_MODE_TRANSPORT=m
CONFIG_INET6_XFRM_MODE_TUNNEL=m
CONFIG_INET6_XFRM_MODE_BEET=m
CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
CONFIG_IPV6_SIT=m
# CONFIG_IPV6_SIT_6RD is not set
CONFIG_IPV6_NDISC_NODETYPE=y
CONFIG_IPV6_TUNNEL=m
CONFIG_IPV6_MULTIPLE_TABLES=y
CONFIG_IPV6_SUBTREES=y
CONFIG_IPV6_MROUTE=y
CONFIG_IPV6_PIMSM_V2=y
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
CONFIG_STP=m
CONFIG_BRIDGE=m
# CONFIG_NET_DSA is not set
CONFIG_VLAN_8021Q=m
# CONFIG_VLAN_8021Q_GVRP is not set
# CONFIG_DECNET is not set
CONFIG_LLC=m
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_PHONET is not set
# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
# CONFIG_DCB is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NET_TCPPROBE is not set
# CONFIG_NET_DROP_MONITOR is not set
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
CONFIG_FIB_RULES=y
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
# CONFIG_LIB80211 is not set

#
# CFG80211 needs to be enabled for MAC80211
#
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
CONFIG_FIRMWARE_IN_KERNEL=y
CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
# CONFIG_PARPORT is not set
CONFIG_PNP=y
CONFIG_PNP_DEBUG_MESSAGES=y

#
# Protocols
#
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set

#
# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
#
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_IBM_ASM is not set
# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_HP_ILO is not set
# CONFIG_C2PORT is not set

#
# EEPROM support
#
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_CB710_CORE is not set
CONFIG_HAVE_IDE=y
CONFIG_IDE=y

#
# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
CONFIG_IDE_XFER_MODE=y
CONFIG_IDE_TIMINGS=y
CONFIG_IDE_ATAPI=y
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_IDE_GD=y
CONFIG_IDE_GD_ATA=y
# CONFIG_IDE_GD_ATAPI is not set
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEACPI=y
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_PROC_FS=y

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_PLATFORM is not set
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEDMA_SFF=y

#
# PCI IDE chipsets support
#
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_GENERIC is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
CONFIG_BLK_DEV_ATIIXP=y
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_IT8172 is not set
# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
CONFIG_BLK_DEV_PDC202XX_NEW=y
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_BLK_DEV_TC86C001 is not set
CONFIG_BLK_DEV_IDEDMA=y

#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
CONFIG_SCSI_NETLINK=y
# CONFIG_SCSI_PROC_FS is not set

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
CONFIG_SCSI_WAIT_SCAN=m

#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
CONFIG_SCSI_FC_ATTRS=y
# CONFIG_SCSI_ISCSI_ATTRS is not set
CONFIG_SCSI_SAS_ATTRS=y
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_SCSI_CXGB3_ISCSI is not set
# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_BE2ISCSI is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
CONFIG_SCSI_AIC79XX=y
CONFIG_AIC79XX_CMDS_PER_DEVICE=32
CONFIG_AIC79XX_RESET_DELAY_MS=4000
# CONFIG_AIC79XX_DEBUG_ENABLE is not set
CONFIG_AIC79XX_DEBUG_MASK=0
# CONFIG_AIC79XX_REG_PRETTY_PRINT is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_MPT2SAS is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_FCOE is not set
# CONFIG_FCOE_FNIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_BFA_FC is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_ATA_ACPI=y
CONFIG_SATA_PMP=y
CONFIG_SATA_AHCI=y
# CONFIG_SATA_SIL24 is not set
CONFIG_ATA_SFF=y
CONFIG_SATA_SVW=y
CONFIG_ATA_PIIX=y
# CONFIG_SATA_MV is not set
CONFIG_SATA_NV=y
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
CONFIG_SATA_SIL=y
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
CONFIG_SATA_VIA=y
# CONFIG_SATA_VITESSE is not set
# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ACPI is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_TOSHIBA is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
# CONFIG_PATA_SCH is not set
CONFIG_MD=y
# CONFIG_BLK_DEV_MD is not set
CONFIG_BLK_DEV_DM=y
# CONFIG_DM_DEBUG is not set
# CONFIG_DM_CRYPT is not set
# CONFIG_DM_SNAPSHOT is not set
# CONFIG_DM_MIRROR is not set
# CONFIG_DM_ZERO is not set
# CONFIG_DM_MULTIPATH is not set
# CONFIG_DM_DELAY is not set
# CONFIG_DM_UEVENT is not set
CONFIG_FUSION=y
CONFIG_FUSION_SPI=y
CONFIG_FUSION_FC=y
CONFIG_FUSION_SAS=y
CONFIG_FUSION_MAX_SGE=128
CONFIG_FUSION_CTL=y
CONFIG_FUSION_LOGGING=y

#
# IEEE 1394 (FireWire) support
#

#
# You can enable one or both FireWire driver stacks.
#

#
# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
CONFIG_IEEE1394=y
CONFIG_IEEE1394_OHCI1394=y

#
# PCILynx controller requires I2C
#
# CONFIG_IEEE1394_SBP2 is not set
# CONFIG_IEEE1394_ETH1394_ROM_ENTRY is not set
# CONFIG_IEEE1394_ETH1394 is not set
CONFIG_IEEE1394_RAWIO=y
# CONFIG_IEEE1394_VIDEO1394 is not set
# CONFIG_IEEE1394_DV1394 is not set
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_I2O is not set
CONFIG_MACINTOSH_DRIVERS=y
# CONFIG_MAC_EMUMOUSEBTN is not set
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
CONFIG_BONDING=m
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=y
# CONFIG_VETH is not set
# CONFIG_NET_SB1000 is not set
# CONFIG_ARCNET is not set
CONFIG_PHYLIB=m

#
# MII PHY device drivers
#
# CONFIG_MARVELL_PHY is not set
# CONFIG_DAVICOM_PHY is not set
# CONFIG_QSEMI_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_CICADA_PHY is not set
# CONFIG_VITESSE_PHY is not set
# CONFIG_SMSC_PHY is not set
# CONFIG_BROADCOM_PHY is not set
# CONFIG_ICPLUS_PHY is not set
# CONFIG_REALTEK_PHY is not set
# CONFIG_NATIONAL_PHY is not set
# CONFIG_STE10XP is not set
# CONFIG_LSI_ET1011C_PHY is not set
# CONFIG_MDIO_BITBANG is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_ETHOC is not set
# CONFIG_DNET is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
CONFIG_E100=m
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_R6040 is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SMSC9420 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_KS8842 is not set
# CONFIG_KS8851_MLL is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
# CONFIG_ATL2 is not set
CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
CONFIG_E1000=m
CONFIG_E1000E=m
# CONFIG_IP1000 is not set
CONFIG_IGB=m
CONFIG_IGB_DCA=y
# CONFIG_IGBVF is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_VIA_VELOCITY is not set
CONFIG_TIGON3=m
# CONFIG_BNX2 is not set
# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_ATL1C is not set
# CONFIG_JME is not set
CONFIG_NETDEV_10000=y
CONFIG_MDIO=m
# CONFIG_CHELSIO_T1 is not set
CONFIG_CHELSIO_T3_DEPENDS=y
# CONFIG_CHELSIO_T3 is not set
# CONFIG_ENIC is not set
CONFIG_IXGBE=m
CONFIG_IXGBE_DCA=y
CONFIG_IXGB=m
# CONFIG_S2IO is not set
# CONFIG_VXGE is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
# CONFIG_NIU is not set
# CONFIG_MLX4_EN is not set
# CONFIG_MLX4_CORE is not set
# CONFIG_TEHUTI is not set
# CONFIG_BNX2X is not set
# CONFIG_QLGE is not set
# CONFIG_SFC is not set
# CONFIG_BE2NET is not set
# CONFIG_TR is not set
CONFIG_WLAN=y
# CONFIG_AIRO is not set
# CONFIG_ATMEL is not set
# CONFIG_PRISM54 is not set
# CONFIG_USB_ZD1201 is not set
# CONFIG_HOSTAP is not set

#
# Enable WiMAX (Networking options) to see the WiMAX drivers
#

#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
CONFIG_NETCONSOLE=y
# CONFIG_NETCONSOLE_DYNAMIC is not set
CONFIG_NETPOLL=y
# CONFIG_NETPOLL_TRAP is not set
CONFIG_NET_POLL_CONTROLLER=y
# CONFIG_VMXNET3 is not set
# CONFIG_ISDN is not set
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_LIFEBOOK=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
# CONFIG_MOUSE_PS2_ELANTECH is not set
# CONFIG_MOUSE_PS2_SENTELIC is not set
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_BCM5974 is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NOZOMI is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_FIX_EARLYCON_MEM=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_PNP=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
CONFIG_HW_RANDOM=y
# CONFIG_HW_RANDOM_TIMERIOMEM is not set
CONFIG_HW_RANDOM_INTEL=y
CONFIG_HW_RANDOM_AMD=y
CONFIG_HW_RANDOM_VIA=y
# CONFIG_NVRAM is not set
CONFIG_RTC=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
CONFIG_RAW_DRIVER=y
CONFIG_MAX_RAW_DEVS=256
CONFIG_HPET=y
CONFIG_HPET_MMAP=y
# CONFIG_HANGCHECK_TIMER is not set
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
# CONFIG_SPI is not set

#
# PPS support
#
# CONFIG_PPS is not set
CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
# CONFIG_GPIOLIB is not set
# CONFIG_W1 is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
# CONFIG_HWMON is not set
CONFIG_THERMAL=y
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y

#
# Sonics Silicon Backplane
#
CONFIG_SSB=y
CONFIG_SSB_SPROM=y
CONFIG_SSB_PCIHOST_POSSIBLE=y
CONFIG_SSB_PCIHOST=y
# CONFIG_SSB_B43_PCI_BRIDGE is not set
# CONFIG_SSB_DEBUG is not set
CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
CONFIG_SSB_DRIVER_PCICORE=y

#
# Multifunction device drivers
#
# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set

#
# Graphics support
#
CONFIG_AGP=y
CONFIG_AGP_AMD64=y
CONFIG_AGP_INTEL=y
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_VIA is not set
CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set

#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_VGACON_SOFT_SCROLLBACK=y
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=256
CONFIG_DUMMY_CONSOLE=y
CONFIG_SOUND=y
CONFIG_SOUND_OSS_CORE=y
CONFIG_SOUND_OSS_CORE_PRECLAIM=y
# CONFIG_SND is not set
CONFIG_SOUND_PRIME=y
# CONFIG_SOUND_OSS is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HIDRAW is not set

#
# USB Input Devices
#
CONFIG_USB_HID=y
# CONFIG_HID_PID is not set
# CONFIG_USB_HIDDEV is not set

#
# Special HID drivers
#
CONFIG_HID_A4TECH=y
CONFIG_HID_APPLE=y
CONFIG_HID_BELKIN=y
CONFIG_HID_CHERRY=y
CONFIG_HID_CHICONY=y
CONFIG_HID_CYPRESS=y
CONFIG_HID_DRAGONRISE=y
# CONFIG_DRAGONRISE_FF is not set
CONFIG_HID_EZKEY=y
CONFIG_HID_KYE=y
CONFIG_HID_GYRATION=y
CONFIG_HID_TWINHAN=y
CONFIG_HID_KENSINGTON=y
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
# CONFIG_LOGIRUMBLEPAD2_FF is not set
CONFIG_HID_MICROSOFT=y
CONFIG_HID_MONTEREY=y
CONFIG_HID_NTRIG=y
CONFIG_HID_PANTHERLORD=y
# CONFIG_PANTHERLORD_FF is not set
CONFIG_HID_PETALYNX=y
CONFIG_HID_SAMSUNG=y
CONFIG_HID_SONY=y
CONFIG_HID_SUNPLUS=y
CONFIG_HID_GREENASIA=y
# CONFIG_GREENASIA_FF is not set
CONFIG_HID_SMARTJOYPLUS=y
# CONFIG_SMARTJOYPLUS_FF is not set
CONFIG_HID_TOPSEED=y
CONFIG_HID_THRUSTMASTER=y
# CONFIG_THRUSTMASTER_FF is not set
CONFIG_HID_ZEROPLUS=y
# CONFIG_ZEROPLUS_FF is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_DEVICE_CLASS is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
CONFIG_USB_MON=y
# CONFIG_USB_WUSB is not set
# CONFIG_USB_WUSB_CBAF is not set

#
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
# CONFIG_USB_XHCI_HCD is not set
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_HCD_SSB is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_WHCI_HCD is not set
# CONFIG_USB_HWA_HCD is not set

#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=y
# CONFIG_USB_WDM is not set
# CONFIG_USB_TMC is not set

#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#

#
# also be needed; see USB_STORAGE Help for more info
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_LIBUSUAL is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set

#
# USB port drivers
#
# CONFIG_USB_SERIAL is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_SEVSEG is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
# CONFIG_USB_GADGET is not set

#
# OTG and related infrastructure
#
# CONFIG_NOP_USB_XCEIV is not set
# CONFIG_UWB is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
# CONFIG_RTC_CLASS is not set
CONFIG_DMADEVICES=y

#
# DMA Devices
#
CONFIG_ASYNC_TX_DISABLE_CHANNEL_SWITCH=y
CONFIG_INTEL_IOATDMA=m
CONFIG_DMA_ENGINE=y

#
# DMA Clients
#
CONFIG_NET_DMA=y
# CONFIG_ASYNC_TX_DMA is not set
# CONFIG_DMATEST is not set
CONFIG_DCA=m
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set

#
# TI VLYNQ
#
# CONFIG_STAGING is not set
CONFIG_X86_PLATFORM_DEVICES=y
# CONFIG_ASUS_LAPTOP is not set
# CONFIG_THINKPAD_ACPI is not set
# CONFIG_INTEL_MENLOW is not set
# CONFIG_ACPI_WMI is not set
# CONFIG_ACPI_ASUS is not set
# CONFIG_TOPSTAR_LAPTOP is not set
# CONFIG_ACPI_TOSHIBA is not set

#
# Firmware Drivers
#
# CONFIG_EDD is not set
CONFIG_FIRMWARE_MEMMAP=y
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set
CONFIG_DMIID=y
# CONFIG_ISCSI_IBFT_FIND is not set

#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
# CONFIG_EXT2_FS_SECURITY is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
# CONFIG_EXT4_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
# CONFIG_INOTIFY is not set
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
CONFIG_GENERIC_ACL=y

#
# Caches
#
# CONFIG_FSCACHE is not set

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
# CONFIG_UDF_FS is not set

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
# CONFIG_CONFIGFS_FS is not set
CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_RPCSEC_GSS_KRB5=m
CONFIG_RPCSEC_GSS_SPKM3=m
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
# CONFIG_CIFS_WEAK_PW_HASH is not set
# CONFIG_CIFS_XATTR is not set
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y
# CONFIG_DLM is not set

#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=2048
CONFIG_MAGIC_SYSRQ=y
# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_UNUSED_SYMBOLS=y
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_DETECT_HUNG_TASK=y
# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_OBJECTS is not set
CONFIG_DEBUG_SLAB=y
CONFIG_DEBUG_SLAB_LEAK=y
# CONFIG_DEBUG_KMEMLEAK is not set
CONFIG_DEBUG_PREEMPT=y
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
CONFIG_STACKTRACE=y
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_VIRTUAL is not set
# CONFIG_DEBUG_WRITECOUNT is not set
CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_ARCH_WANT_FRAME_POINTERS=y
CONFIG_FRAME_POINTER=y
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_KPROBES_SANITY_TEST is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_LKDTM is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_USER_STACKTRACE_SUPPORT=y
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_FP_TEST=y
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_PROVIDE_OHCI1394_DMA_INIT is not set
# CONFIG_DYNAMIC_DEBUG is not set
CONFIG_DMA_API_DEBUG=y
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
CONFIG_HAVE_ARCH_KMEMCHECK=y
# CONFIG_STRICT_DEVMEM is not set
CONFIG_X86_VERBOSE_BOOTUP=y
CONFIG_EARLY_PRINTK=y
# CONFIG_EARLY_PRINTK_DBGP is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_PER_CPU_MAPS is not set
# CONFIG_X86_PTDUMP is not set
CONFIG_DEBUG_RODATA=y
CONFIG_DEBUG_RODATA_TEST=y
# CONFIG_DEBUG_NX_TEST is not set
# CONFIG_IOMMU_DEBUG is not set
# CONFIG_IOMMU_STRESS is not set
CONFIG_HAVE_MMIOTRACE_SUPPORT=y
# CONFIG_X86_DECODER_SELFTEST is not set
CONFIG_IO_DELAY_TYPE_0X80=0
CONFIG_IO_DELAY_TYPE_0XED=1
CONFIG_IO_DELAY_TYPE_UDELAY=2
CONFIG_IO_DELAY_TYPE_NONE=3
CONFIG_IO_DELAY_0X80=y
# CONFIG_IO_DELAY_0XED is not set
# CONFIG_IO_DELAY_UDELAY is not set
# CONFIG_IO_DELAY_NONE is not set
CONFIG_DEFAULT_IO_DELAY_TYPE=0
# CONFIG_DEBUG_BOOT_PARAMS is not set
# CONFIG_CPA_DEBUG is not set
# CONFIG_OPTIMIZE_INLINING is not set
# CONFIG_DEBUG_STRICT_USER_COPY_CHECKS is not set

#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
# CONFIG_DEFAULT_SECURITY_SELINUX is not set
# CONFIG_DEFAULT_SECURITY_SMACK is not set
# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
CONFIG_DEFAULT_SECURITY_DAC=y
CONFIG_DEFAULT_SECURITY=""
CONFIG_ASYNC_TX_DISABLE_PQ_VAL_DMA=y
CONFIG_ASYNC_TX_DISABLE_XOR_VAL_DMA=y
CONFIG_CRYPTO=y

#
# Crypto core or helper
#
# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=m
CONFIG_CRYPTO_ALGAPI2=m
CONFIG_CRYPTO_AEAD=m
CONFIG_CRYPTO_AEAD2=m
CONFIG_CRYPTO_BLKCIPHER=m
CONFIG_CRYPTO_BLKCIPHER2=m
CONFIG_CRYPTO_HASH=m
CONFIG_CRYPTO_HASH2=m
CONFIG_CRYPTO_RNG=m
CONFIG_CRYPTO_RNG2=m
CONFIG_CRYPTO_PCOMP=m
CONFIG_CRYPTO_MANAGER=m
CONFIG_CRYPTO_MANAGER2=m
# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_NULL is not set
CONFIG_CRYPTO_WORKQUEUE=m
# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_AUTHENC=m
# CONFIG_CRYPTO_TEST is not set

#
# Authenticated Encryption with Associated Data
#
# CONFIG_CRYPTO_CCM is not set
# CONFIG_CRYPTO_GCM is not set
# CONFIG_CRYPTO_SEQIV is not set

#
# Block modes
#
CONFIG_CRYPTO_CBC=m
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
# CONFIG_CRYPTO_ECB is not set
# CONFIG_CRYPTO_LRW is not set
# CONFIG_CRYPTO_PCBC is not set
# CONFIG_CRYPTO_XTS is not set

#
# Hash modes
#
CONFIG_CRYPTO_HMAC=m
# CONFIG_CRYPTO_XCBC is not set
# CONFIG_CRYPTO_VMAC is not set

#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_CRC32C_INTEL is not set
# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=m
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_RMD128 is not set
# CONFIG_CRYPTO_RMD160 is not set
# CONFIG_CRYPTO_RMD256 is not set
# CONFIG_CRYPTO_RMD320 is not set
CONFIG_CRYPTO_SHA1=m
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_WP512 is not set

#
# Ciphers
#
CONFIG_CRYPTO_AES=m
# CONFIG_CRYPTO_AES_X86_64 is not set
# CONFIG_CRYPTO_AES_NI_INTEL is not set
# CONFIG_CRYPTO_ANUBIS is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_CAMELLIA is not set
CONFIG_CRYPTO_CAST5=m
# CONFIG_CRYPTO_CAST6 is not set
CONFIG_CRYPTO_DES=m
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_SALSA20 is not set
# CONFIG_CRYPTO_SALSA20_X86_64 is not set
# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_TWOFISH_X86_64 is not set

#
# Compression
#
CONFIG_CRYPTO_DEFLATE=m
# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set

#
# Random Number Generation
#
CONFIG_CRYPTO_ANSI_CPRNG=m
CONFIG_CRYPTO_HW=y
# CONFIG_CRYPTO_DEV_PADLOCK is not set
# CONFIG_CRYPTO_DEV_HIFN_795X is not set
CONFIG_HAVE_KVM=y
CONFIG_VIRTUALIZATION=y
# CONFIG_KVM is not set
# CONFIG_VIRTIO_PCI is not set
# CONFIG_VIRTIO_BALLOON is not set
CONFIG_BINARY_PRINTF=y

#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_GENERIC_FIND_FIRST_BIT=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_FIND_LAST_BIT=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_DECOMPRESS_GZIP=y
CONFIG_DECOMPRESS_BZIP2=y
CONFIG_DECOMPRESS_LZMA=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_NLATTR=y

Re: [PATCH 0/3] increase skb size to prevent dma over skb boundary

[Neil Horman]

On Thu, Dec 10, 2009 at 11:20:58AM -0700, Tantilov, Emil S wrote:
> Neil Horman wrote:
> > On Tue, Dec 08, 2009 at 04:37:39PM -0700, Tantilov, Emil S wrote:
> >> Neil Horman wrote:
> >>> Hey all-
> >>> 	I was tracking down a memory corruptor lately in which, with
> >>> DEBUG_SLAB enabled we were getting several redzone violoations,
> >>> which was always followed by an oops in the rx receive path when
> >>> using the e1000e driver.  Looking at the cores, the slabs that had
> >>> their redzone violated were always adjacent to a size-2048 slab
> >>> which was allocated by __netdev_alloc_skb.  Doing some
> >>> instrumentation led me to see the following.  When the e1000e
> >>> driver sets up its rctl register, which defines the length of each
> >>> of the buffers in the rx ring, we do this: 
> >>> 
> >>> switch (adapter->rx_buffer_len) {
> >>>         case 256:
> >>>                 rctl |= E1000_RCTL_SZ_256;
> >>>                 rctl &= ~E1000_RCTL_BSEX;
> >>>                 break;
> >>>         case 512:
> >>>                 rctl |= E1000_RCTL_SZ_512;
> >>>                 rctl &= ~E1000_RCTL_BSEX;
> >>>                 break;
> >>>         case 1024:
> >>>                 rctl |= E1000_RCTL_SZ_1024;
> >>>                 rctl &= ~E1000_RCTL_BSEX;
> >>>                 break;
> >>>         case 2048:
> >>>         default:
> >>>                 rctl |= E1000_RCTL_SZ_2048;
> >>>                 rctl &= ~E1000_RCTL_BSEX;
> >>>                 break;
> >>>         case 4096:
> >>>                 rctl |= E1000_RCTL_SZ_4096;
> >>>                 break;
> >>>         case 8192:
> >>>                 rctl |= E1000_RCTL_SZ_8192;
> >>>                 break;
> >>>         case 16384:
> >>>                 rctl |= E1000_RCTL_SZ_16384;
> >>>                 break;
> >>>         }
> >>> }
> >>> 
> >>> This is problematic since rx_buffer_len is set to 1500, which causes
> >>> the rctl value to fall into the default case, which configures the
> >>> hardware to think it can dma up to 2048 bytes into each buffer,
> >>> despite the fact that the buffer is only 1500 bytes long.  If we
> >>> receive a frame that is longer than 1500 bytes, then the dma will
> >>> overrun the 1500 byte limit of the sk_buff's data block spilling
> >>> into the skb_shared_info structure (which is placed immediately
> >>> after the end of the skb->end pointer (or at skb->head + skb->end if
> >>> NET_SKBUFF_DATA_USES_OFFSET is configured).  In either case, the
> >>> spillover corrupts the skb_shared_info structure, and sets us up for
> >>> any number of subsequent corruptions/oopses/failures.  I've fixed
> >>> this by normalizing the rx_buffer_length value in the setup_rctl
> >>> function, which rounds up the length to the configured value of
> >>> rctl, forcing us to allocate buffers of a size that meet the
> >>> hardwares configuration needs. 
> >>> 
> >>> I've tested this on e1000e and confirmed that it fixes my redzone
> >>> violations and the observed oops.  Visual inspection indicates that
> >>> e1000 and ixgb also need this fix.  I've not explicitly tested them
> >>> though, so I've split this into three separate patches
> >>> 
> >>> Regards
> >>> Neil
> >>> 
> >>> Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
> >> 
> >> Hi Neil,
> >> 
> >> I am trying to test the patches you submitted (thanks btw) and so
> >> far am not able to reproduce the panic you described. When MTU is at
> >> 1500 RCTL.LPE (bit 5) is set to 0 and the HW will not allow the
> >> reception of large packets (>1522 bytes, which is what rx_buffer_len
> >> is set to). This is basically what I am seeing in my tests - packets
> >> are discarded by the HW.     
> >> 
> >> Can you provide more details about the setup you used? Steps to
> >> reproduce and also details (lspci -vvv, ethtool -e, ethtool -d) of
> >> the HW you used and kernel config should help as well.  
> >> 
> >> Thanks,
> >> Emil--
> >> To unsubscribe from this list: send the line "unsubscribe netdev" in
> >> the body of a message to majordomo@vger.kernel.org
> >> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> >> 
> > 
> > 
> > Heres the data you asked for.  The config isn't exact, as the system
> > in question was installed a few times over since I worked on this,
> > but it should be very close.  The only differnce I see on this config
> > is that CONFIG_SLAB_DEBUG is turned on.  Everything else should be
> > identical 
> 
> Thanks for the data. Your config could not apply on my kernel (net-next-2.6 master branch). So I attached the one I used for testing in case you see anything that is different. I made sure DEBUG_SLAB is enabled.
> 
It might not apply cleanly no.  as I said, I had to reconstruct it (it was
originoally from an older kernel that I applied to a newer kernel)

> Is this the connectathon suite you were talking about:
> http://www.connectathon.org/nfstests.html
> 
Yes, thats the one.

> I ran overnight stress (1000 iterations of the suite)  plus some netperf stress and so far no signs of issues on a z-200 platform. 
> 
> BTW the HP z-200 is still in pre-production stage. Looking at the eeprom you provided it seems older than what we have. You should probably look into getting an updated FW.
> 
That might be worth looking into.  Thanks.  That said however, if its possible
for the eeprom to allow overlength frames to get dma-ed, isn't it worthwhile to
ensure that our allocation size matches what we tell the driver it is?  We
already do so in e1000_change_mtu:
...

	if (max_frame <= 256)
                adapter->rx_buffer_len = 256;
        else if (max_frame <= 512)
                adapter->rx_buffer_len = 512;
        else if (max_frame <= 1024)
                adapter->rx_buffer_len = 1024;
        else if (max_frame <= 2048)
                adapter->rx_buffer_len = 2048;
        else
                adapter->rx_buffer_len = 4096;
...

These patches just ensure that the same normalization is done for the initial
size of rx_buffer_len, should userspace never change the mtu of the NIC.

Regards
Neil

> Thanks,
> Emil
> 

Re: [PATCH 0/3] increase skb size to prevent dma over skb boundary

[Brandon Philips]

On 11:20 Thu 10 Dec 2009, Tantilov, Emil S wrote:
> >> I am trying to test the patches you submitted (thanks btw) and so
> >> far am not able to reproduce the panic you described. When MTU is at
> >> 1500 RCTL.LPE (bit 5) is set to 0 and the HW will not allow the
> >> reception of large packets (>1522 bytes, which is what rx_buffer_len
> >> is set to). This is basically what I am seeing in my tests - packets
> >> are discarded by the HW.     

I have a memory dump from an SLE10 SP3 machine that seems to reproduce
this issue. The testing environment was netperf with the MTU being
switched every minute from 9000 -> 1500 and it took 40 hours to hit
the bug. So, an overnight test, as you tried, may not be enough.

In the memory dump there are 6 skb's in the ring that have memory
overwritten from skb->data to skb->data + 2048. The machine ended up
oopsing in skb_release_data() from e1000_clean_all_rx_rings() from
e1000_change_mtu().

I will let you know if this patch ended up helping.

Cheers,

	Brandon

35:00.1 Ethernet controller: Intel Corporation 82571EB Gigabit Ethernet Controller (Copper) (rev 06)
        Subsystem: Intel Corporation PRO/1000 PT Quad Port LP Server Adapter
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 91
        Region 0: Memory at c9120000 (32-bit, non-prefetchable) [size=128K]
        Region 1: Memory at c9100000 (32-bit, non-prefetchable) [size=128K]
        Region 2: I/O ports at <unassigned>
        Expansion ROM at fda20000 [disabled] [size=128K]
        Capabilities: [c8] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable+
                Address: 00000000fee1d000  Data: 405b
        Capabilities: [e0] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
                LnkCap: Port #2, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 <4us, L1 <64us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Kernel driver in use: e1000
        Kernel modules: e1000

Re: [PATCH 0/3] increase skb size to prevent dma over skb boundary

[Brandeburg, Jesse]

On Tue, 22 Dec 2009, Brandon Philips wrote:
> On 11:20 Thu 10 Dec 2009, Tantilov, Emil S wrote:
> > >> I am trying to test the patches you submitted (thanks btw) and so
> > >> far am not able to reproduce the panic you described. When MTU is at
> > >> 1500 RCTL.LPE (bit 5) is set to 0 and the HW will not allow the
> > >> reception of large packets (>1522 bytes, which is what rx_buffer_len
> > >> is set to). This is basically what I am seeing in my tests - packets
> > >> are discarded by the HW.     
> 
> I have a memory dump from an SLE10 SP3 machine that seems to reproduce
> this issue. The testing environment was netperf with the MTU being
> switched every minute from 9000 -> 1500 and it took 40 hours to hit
> the bug. So, an overnight test, as you tried, may not be enough.

Thanks for testing Brandon, I think your test (with e1000e 1.0.2.5) is 
significantly different than the test that Neil started with.  That said I 
think it is a valuable test and we are going to start a test today that 
uses pktgen on two machines to send 64 byte and 9014 byte packets to a 
host that is changing its MTU every 5-10 seconds.
 
> In the memory dump there are 6 skb's in the ring that have memory
> overwritten from skb->data to skb->data + 2048. The machine ended up
> oopsing in skb_release_data() from e1000_clean_all_rx_rings() from
> e1000_change_mtu().

I think we should put a patch like the below into the kernel and actually 
*catch* any overrun DMAs even on a production machine.  At that point we 
could even leak that skb memory to prevent the corrupted memory from 
making its way into the general environment.
 
> 35:00.1 Ethernet controller: Intel Corporation 82571EB Gigabit Ethernet Controller (Copper) (rev 06)

what kind of system is this that had such a high bus number? PPC64?

>         Subsystem: Intel Corporation PRO/1000 PT Quad Port LP Server Adapter
>         Kernel driver in use: e1000
>         Kernel modules: e1000

e1000_change_mtu could possibly have a race that would allow corruption if 
all receives were not completed in the time we waited (10 millseconds) for 
some reason, but only if LPE was cleared already.  I still think your test 
is significantly different and maybe showing a different (but similar) 
edge case bug than Neil.

shouldn't IOMMU systems be catching this too when it was occuring?  we 
only call pci_map_* with buffer_info->length which is assigned 
rx_buffer_len.

e1000/e1000e: check rx length for overruns

From: Jesse Brandeburg <jesse.brandeburg@intel.com>

it has been reported that some tests can cause DMA overruns resulting in
corrupted memory.  If the hardware writes more data to memory than we had
allocated this is something we can check for.

For now, WARN_ON, with the future capability of doing something like leaking
the memory rather than returning a known corrupt buffer to userspace.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: brandon@ifup.org
CC: nhorman@tuxdriver.com
---

 drivers/net/e1000/e1000_main.c |    3 +++
 drivers/net/e1000e/netdev.c    |    4 ++++
 2 files changed, 7 insertions(+), 0 deletions(-)


diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
index 7e855f9..911258b 100644
--- a/drivers/net/e1000/e1000_main.c
+++ b/drivers/net/e1000/e1000_main.c
@@ -3666,6 +3666,7 @@ static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
 		buffer_info->dma = 0;
 
 		length = le16_to_cpu(rx_desc->length);
+		WARN_ON(length > buffer_info->length);
 
 		/* errors is only valid for DD + EOP descriptors */
 		if (unlikely((status & E1000_RXD_STAT_EOP) &&
@@ -3849,6 +3850,8 @@ static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
 		buffer_info->dma = 0;
 
 		length = le16_to_cpu(rx_desc->length);
+		WARN_ON(length > buffer_info->length);
+
 		/* !EOP means multiple descriptors were used to store a single
 		 * packet, also make sure the frame isn't just CRC only */
 		if (unlikely(!(status & E1000_RXD_STAT_EOP) || (length <= 4))) {
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 762b697..394c2dc 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -449,6 +449,7 @@ static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
 		buffer_info->dma = 0;
 
 		length = le16_to_cpu(rx_desc->length);
+		WARN_ON(length > adapter->rx_buffer_len);
 
 		/* !EOP means multiple descriptors were used to store a single
 		 * packet, also make sure the frame isn't just CRC only */
@@ -758,6 +759,7 @@ static bool e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
 		}
 
 		length = le16_to_cpu(rx_desc->wb.middle.length0);
+		WARN_ON(length > adapter->rx_ps_bsize0);
 
 		if (!length) {
 			e_dbg("Last part of the packet spanning multiple "
@@ -814,6 +816,7 @@ static bool e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
 			if (!length)
 				break;
 
+			WARN_ON(length > PAGE_SIZE);
 			ps_page = &buffer_info->ps_pages[j];
 			pci_unmap_page(pdev, ps_page->dma, PAGE_SIZE,
 				       PCI_DMA_FROMDEVICE);
@@ -939,6 +942,7 @@ static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
 		buffer_info->dma = 0;
 
 		length = le16_to_cpu(rx_desc->length);
+		WARN_ON(length > PAGE_SIZE);
 
 		/* errors is only valid for DD + EOP descriptors */
 		if (unlikely((status & E1000_RXD_STAT_EOP) &&

Re: [PATCH 0/3] increase skb size to prevent dma over skb boundary

[Neil Horman]

On Wed, Dec 23, 2009 at 11:43:40AM -0800, Brandeburg, Jesse wrote:
> On Tue, 22 Dec 2009, Brandon Philips wrote:
> > On 11:20 Thu 10 Dec 2009, Tantilov, Emil S wrote:
> > > >> I am trying to test the patches you submitted (thanks btw) and so
> > > >> far am not able to reproduce the panic you described. When MTU is at
> > > >> 1500 RCTL.LPE (bit 5) is set to 0 and the HW will not allow the
> > > >> reception of large packets (>1522 bytes, which is what rx_buffer_len
> > > >> is set to). This is basically what I am seeing in my tests - packets
> > > >> are discarded by the HW.     
> > 
> > I have a memory dump from an SLE10 SP3 machine that seems to reproduce
> > this issue. The testing environment was netperf with the MTU being
> > switched every minute from 9000 -> 1500 and it took 40 hours to hit
> > the bug. So, an overnight test, as you tried, may not be enough.
> 
> Thanks for testing Brandon, I think your test (with e1000e 1.0.2.5) is 
> significantly different than the test that Neil started with.  That said I 
> think it is a valuable test and we are going to start a test today that 
> uses pktgen on two machines to send 64 byte and 9014 byte packets to a 
> host that is changing its MTU every 5-10 seconds.
>  
> > In the memory dump there are 6 skb's in the ring that have memory
> > overwritten from skb->data to skb->data + 2048. The machine ended up
> > oopsing in skb_release_data() from e1000_clean_all_rx_rings() from
> > e1000_change_mtu().
> 
> I think we should put a patch like the below into the kernel and actually 
> *catch* any overrun DMAs even on a production machine.  At that point we 
> could even leak that skb memory to prevent the corrupted memory from 
> making its way into the general environment.
>  
> > 35:00.1 Ethernet controller: Intel Corporation 82571EB Gigabit Ethernet Controller (Copper) (rev 06)
> 
> what kind of system is this that had such a high bus number? PPC64?
> 
> >         Subsystem: Intel Corporation PRO/1000 PT Quad Port LP Server Adapter
> >         Kernel driver in use: e1000
> >         Kernel modules: e1000
> 
> e1000_change_mtu could possibly have a race that would allow corruption if 
> all receives were not completed in the time we waited (10 millseconds) for 
> some reason, but only if LPE was cleared already.  I still think your test 
> is significantly different and maybe showing a different (but similar) 
> edge case bug than Neil.
> 
> shouldn't IOMMU systems be catching this too when it was occuring?  we 
> only call pci_map_* with buffer_info->length which is assigned 
> rx_buffer_len.
> 
> e1000/e1000e: check rx length for overruns
> 
> From: Jesse Brandeburg <jesse.brandeburg@intel.com>
> 
> it has been reported that some tests can cause DMA overruns resulting in
> corrupted memory.  If the hardware writes more data to memory than we had
> allocated this is something we can check for.
> 
> For now, WARN_ON, with the future capability of doing something like leaking
> the memory rather than returning a known corrupt buffer to userspace.
> 
> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
> CC: brandon@ifup.org
> CC: nhorman@tuxdriver.com

I think this seems like a reasonable idea.  Additionally (or perhaps
alternatively), it might be a good idea to (when allocating buffers in the
default setup path), expand the allocation size by a word, that we write a
cannary value into.  Then we can check that cannary on the napi poll should the
hardware dma past the end of the skb.
Neil

>