From: Neil Horman <nhorman@tuxdriver.com>
To: "Brandeburg, Jesse" <jesse.brandeburg@intel.com>
Cc: davem@davemloft.net,
"netdev@vger.kernel.org" <netdev@vger.kernel.org>,
"Kirsher, Jeffrey T" <jeffrey.t.kirsher@intel.com>,
"Allan, Bruce W" <bruce.w.allan@intel.com>,
"Waskiewicz Jr, Peter P" <peter.p.waskiewicz.jr@intel.com>,
"Ronciak, John" <john.ronciak@intel.com>,
"e1000-devel@lists.sourceforge.net"
<e1000-devel@lists.sourceforge.net>
Subject: Re: [PATCH] e1000: enhance frame fragment detection
Date: Tue, 12 Jan 2010 21:12:38 -0500 [thread overview]
Message-ID: <20100113021238.GA2165@localhost.localdomain> (raw)
In-Reply-To: <alpine.WNT.2.00.1001121720300.3168@jbrandeb-desk1.amr.corp.intel.com>
On Tue, Jan 12, 2010 at 05:56:28PM -0800, Brandeburg, Jesse wrote:
> On Wed, 6 Jan 2010, Brandeburg, Jesse wrote:
> > a counter patch, without atomic ops, since we are protected by napi when
> > modifying this variable.
> >
> > Originally From: Neil Horman <nhorman@tuxdriver.com>
> > Modified by: Jesse Brandeburg <jesse.brandeburg@intel.com>
> >
> > <original message>
> > Hey all-
> > A security discussion was recently given:
> > http://events.ccc.de/congress/2009/Fahrplan//events/3596.en.html
> > And a patch that I submitted awhile back was brought up. Apparently some of
> > their testing revealed that they were able to force a buffer fragment in e1000
> > in which the trailing fragment was greater than 4 bytes. As a result the
> > fragment check I introduced failed to detect the fragement and a partial
> > invalid frame was passed up into the network stack. I've written this patch
> > to correct it. I'm in the process of testing it now, but it makes good
> > logical sense to me. Effectively it maintains a per-adapter state variable
> > which detects a non-EOP frame, and discards it and subsequent non-EOP frames
> > leading up to _and_ _including_ the next positive-EOP frame (as it is by
> > definition the last fragment). This should prevent any and all partial frames
> > from entering the network stack from e1000.
> >
> > Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
>
> I would like to withdraw this patch, at least for 2.6.32+ e1000 and e1000e
> are both not susceptible to this attack. We have verified the below with
> testing, including code modifications to guarantee the correct paths were
> taken when receiving overlong frames.
>
> What has happened is that in commit
> edbbb3ca107715067b27a71e6ea7f58750912aa2 the e1000 driver had a feature
> added to use 4kB data buffers when in jumbo mode. This code understands
> chains of data buffers, (in fact depends on it) so even when receiving a
> packet that is longer than 4kB, the packet is handed in its entirety to
> the stack.
>
> I believe RedHat has not backported this patch, and kernels <= 2.6.31
> still need the fix, so both need some version of this workaround, but
> 2.6.32 does not.
>
> As for e1000e, in jumbo mode it has always used what we call "packet split
> mode" in the driver, where hardware uses a special descriptor that can
> contain 4 dma fragments, a header buffer of 256 bytes and up to 3 4kB data
> buffers. If a packet that arrives is > (12kB + 256) then it will overflow
> into the next descriptor, using only the first 4kB data buffer of the
> second descriptor (our hardware has a hard limit of 16kB for any ethernet
> frame, longer are dropped at the hardware level)
>
> The code correctly handles the !EOP packet and drops it, and the next
> packet will hit the !length (of the header buffer) condition and also be
> dropped.
>
> Other Intel hardware is not susceptible to this attack. Hardware
> supported by the e100 (no jumbo frames), the ixgb driver (MFS register),
> the igb driver (RLPML register), and ixgbe (MHADD/MAXFRS register) do not
> have this issue.
>
> Hope this clears up some things,
>
I'm sorry, it doesn't clear much up, at least not for me. The patch you're
referencing above deals only with the jumbo receive path, not the non-jumbo
case, which is not written to handle skb chains. The vulnerability targets the
latter case specifically. We've seen cases in which an extra data is
transferred into a subsequent buffer in the ring in that path. Normally in our
reproducing cases, I only saw a 4 byte overrun. Theres a check specifically in
the e1000(e) drivers for that case. Unfortunately I never tested other cases,
but if someone sets a low mtu (say 1000 bytes), I don't see why the same issue
can't manifest as a buffer chain consisting of a 1000 byte skb followed by up to
an extra 522 byte skb. such a condition would bypass that check and result in
admitting a garbage frame to the network stack.
Neil
next prev parent reply other threads:[~2010-01-13 2:12 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-12-28 20:10 [PATCH] e1000: enhance frame fragment detection Neil Horman
2009-12-29 0:42 ` Jeff Kirsher
2009-12-29 1:14 ` Neil Horman
2010-01-05 21:44 ` Brandeburg, Jesse
2010-01-05 22:04 ` Neil Horman
2010-01-06 23:27 ` Brandeburg, Jesse
2010-01-07 0:56 ` Neil Horman
2010-01-13 1:56 ` Brandeburg, Jesse
2010-01-13 2:04 ` Ben Hutchings
2010-01-13 2:12 ` Neil Horman [this message]
2010-01-13 2:47 ` Brandeburg, Jesse
2010-01-13 3:33 ` Neil Horman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100113021238.GA2165@localhost.localdomain \
--to=nhorman@tuxdriver.com \
--cc=bruce.w.allan@intel.com \
--cc=davem@davemloft.net \
--cc=e1000-devel@lists.sourceforge.net \
--cc=jeffrey.t.kirsher@intel.com \
--cc=jesse.brandeburg@intel.com \
--cc=john.ronciak@intel.com \
--cc=netdev@vger.kernel.org \
--cc=peter.p.waskiewicz.jr@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).