From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To: jeff@garzik.org
Cc: netdev@vger.kernel.org, gospo@redhat.com,
Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>,
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Subject: [ethtool PATCH 2/2] ethtool: Update manpage with n-tuple information
Date: Fri, 26 Feb 2010 03:56:03 -0800 [thread overview]
Message-ID: <20100226115603.20259.93232.stgit@localhost.localdomain> (raw)
In-Reply-To: <20100226115544.20259.36760.stgit@localhost.localdomain>
From: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Add n-tuple information to the ethtool manpage.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
ethtool.8 | 102 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 102 insertions(+), 0 deletions(-)
diff --git a/ethtool.8 b/ethtool.8
index b45d171..eb6430b 100644
--- a/ethtool.8
+++ b/ethtool.8
@@ -214,6 +214,40 @@ ethtool \- Display or change ethernet card settings
.I ethX
.RI FILE
.RI [ N ]
+
+.B ethtool \-u|\-\-show\-ntuple
+.I ethX
+
+.B ethtool \-U|\-\-config\-ntuple
+.I ethX
+.RB [ flow-type
+.RB tcp4|udp4|sctp4 ]
+.RB [ src-ip
+.IR addr ]
+.RB [ src-ip-mask
+.IR mask ]
+.RB [ dst-ip
+.IR addr ]
+.RB [ dst-ip-mask
+.IR mask ]
+.RB [ src-port
+.IR port ]
+.RB [ src-port-mask
+.IR mask ]
+.RB [ dst-port
+.IR port ]
+.RB [ dst-port-mask
+.IR mask ]
+.RB [ vlan
+.IR VLAN-tag ]
+.RB [ vlan-mask
+.IR mask ]
+.RB [ user-def
+.IR data ]
+.RB [ user-def-mask
+.IR mask ]
+.RB [ action
+.IR queue\ or\ drop ]
.SH DESCRIPTION
.BI ethtool
is used for querying settings of an ethernet device and changing them.
@@ -517,6 +551,74 @@ A number to identify flash region where the image should be flashed.
Default region is 0 which denotes all regions in the flash.
.PD
.RE
+.TP
+.B \-u \-\-show-ntuple
+Get Rx ntuple filters and actions, then display them to the user.
+.PD
+.RE
+.TP
+.B \-U \-\-config-ntuple
+Configure Rx ntuple filters and actions
+.TP
+.B flow-type tcp4|udp4|sctp4
+.RS
+.PD 0
+.TP 3
+.BR "tcp4" " TCP over IPv4"
+.TP 3
+.BR "udp4" " UDP over IPv4"
+.TP 3
+.BR "sctp4" " SCTP over IPv4"
+.PD
+.RE
+.TP
+.BI src-ip \ addr
+Includes the source IP address, specified in hex.
+.TP
+.BI src-ip-mask \ mask
+Specify a mask for the source IP address, specified in hex.
+.TP
+.BI dst-ip \ addr
+Includes the destination IP address, specified in hex.
+.TP
+.BI dst-ip-mask \ mask
+Specify a mask for the destination IP address, specified in hex.
+.TP
+.BI src-port \ port
+Includes the source port, specified in decimal.
+.TP
+.BI src-port-mask \ mask
+Specify a mask for the source port, specified in hex.
+.TP
+.BI dst-port \ port
+Includes the destination port, specified in decimal.
+.TP
+.BI dst-port-mask \ mask
+Specify a mask for the destination port, specified in hex.
+.TP
+.BI vlan \ VLAN-tag
+Includes the VLAN tag, specified in hex.
+.TP
+.BI vlan-mask \ mask
+Specify a mask for the VLAN tag, specified in hex.
+.TP
+.BI user-def \ data
+Includes 64-bits of user-specific data, specified in hex.
+.TP
+.BI user-def-mask \ mask
+Specify a mask for the user-specific data, specified in hex.
+.TP
+.BI action \ N
+Specifies either the Rx queue to send packets to, or to drop
+the matched flow.
+.RS
+.PD 0
+.TP 3
+.BR "-1" " Drop the matched flow"
+.TP 3
+.BR "0 or higher" " Rx queue to route the flow"
+.PD
+.RE
.SH BUGS
Not supported (in part or whole) on all ethernet drivers.
.SH AUTHOR
next prev parent reply other threads:[~2010-02-26 11:56 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-02-26 11:55 [ethtool PATCH 1/2] ethtool: Correctly pull n-tuple string length for get_rx_ntuple Jeff Kirsher
2010-02-26 11:56 ` Jeff Kirsher [this message]
2010-02-26 13:51 ` [ethtool PATCH 2/2] ethtool: Update manpage with n-tuple information Jeff Garzik
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100226115603.20259.93232.stgit@localhost.localdomain \
--to=jeffrey.t.kirsher@intel.com \
--cc=gospo@redhat.com \
--cc=jeff@garzik.org \
--cc=netdev@vger.kernel.org \
--cc=peter.p.waskiewicz.jr@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).