From: Jon Mason <jon.mason@exar.com>
To: Joe Perches <joe@perches.com>
Cc: Ramkrishna Vepa <Ramkrishna.Vepa@exar.com>,
Sreenivasa Honnur <Sreenivasa.Honnur@exar.com>,
"David S. Miller" <davem@davemloft.net>,
netdev <netdev@vger.kernel.org>,
LKML <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH net-next] drivers/net/vxge/vxge-main.c: Use pr_<level> and netdev_<level>
Date: Tue, 27 Jul 2010 22:21:18 -0500 [thread overview]
Message-ID: <20100728032117.GL28630@exar.com> (raw)
In-Reply-To: <1280267223.24054.44.camel@Joe-Laptop.home>
On Tue, Jul 27, 2010 at 02:47:03PM -0700, Joe Perches wrote:
> Use pr_fmt, pr_<level> and netdev_<level> where appropriate.
>
> Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jon Mason <jon.mason@exar.com>
> ---
> drivers/net/vxge/vxge-main.c | 27 +++++++++++----------------
> 1 files changed, 11 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/net/vxge/vxge-main.c b/drivers/net/vxge/vxge-main.c
> index 94d87e8..c7c5605 100644
> --- a/drivers/net/vxge/vxge-main.c
> +++ b/drivers/net/vxge/vxge-main.c
> @@ -41,6 +41,8 @@
> *
> ******************************************************************************/
>
> +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> +
> #include <linux/if_vlan.h>
> #include <linux/pci.h>
> #include <linux/slab.h>
> @@ -144,7 +146,7 @@ vxge_callback_link_up(struct __vxge_hw_device *hldev)
>
> vxge_debug_entryexit(VXGE_TRACE, "%s: %s:%d",
> vdev->ndev->name, __func__, __LINE__);
> - printk(KERN_NOTICE "%s: Link Up\n", vdev->ndev->name);
> + netdev_notice(vdev->ndev, "Link Up\n");
> vdev->stats.link_up++;
>
> netif_carrier_on(vdev->ndev);
> @@ -168,7 +170,7 @@ vxge_callback_link_down(struct __vxge_hw_device *hldev)
>
> vxge_debug_entryexit(VXGE_TRACE,
> "%s: %s:%d", vdev->ndev->name, __func__, __LINE__);
> - printk(KERN_NOTICE "%s: Link Down\n", vdev->ndev->name);
> + netdev_notice(vdev->ndev, "Link Down\n");
>
> vdev->stats.link_down++;
> netif_carrier_off(vdev->ndev);
> @@ -2679,7 +2681,7 @@ vxge_open(struct net_device *dev)
>
> if (vxge_hw_device_link_state_get(vdev->devh) == VXGE_HW_LINK_UP) {
> netif_carrier_on(vdev->ndev);
> - printk(KERN_NOTICE "%s: Link Up\n", vdev->ndev->name);
> + netdev_notice(vdev->ndev, "Link Up\n");
> vdev->stats.link_up++;
> }
>
> @@ -2817,7 +2819,7 @@ int do_vxge_close(struct net_device *dev, int do_io)
> }
>
> netif_carrier_off(vdev->ndev);
> - printk(KERN_NOTICE "%s: Link Down\n", vdev->ndev->name);
> + netdev_notice(vdev->ndev, "Link Down\n");
> netif_tx_stop_all_queues(vdev->ndev);
>
> /* Note that at this point xmit() is stopped by upper layer */
> @@ -3844,9 +3846,7 @@ static pci_ers_result_t vxge_io_slot_reset(struct pci_dev *pdev)
> struct vxgedev *vdev = netdev_priv(netdev);
>
> if (pci_enable_device(pdev)) {
> - printk(KERN_ERR "%s: "
> - "Cannot re-enable device after reset\n",
> - VXGE_DRIVER_NAME);
> + netdev_err(netdev, "Cannot re-enable device after reset\n");
> return PCI_ERS_RESULT_DISCONNECT;
> }
>
> @@ -3871,9 +3871,8 @@ static void vxge_io_resume(struct pci_dev *pdev)
>
> if (netif_running(netdev)) {
> if (vxge_open(netdev)) {
> - printk(KERN_ERR "%s: "
> - "Can't bring device back up after reset\n",
> - VXGE_DRIVER_NAME);
> + netdev_err(netdev,
> + "Can't bring device back up after reset\n");
> return;
> }
> }
> @@ -4430,13 +4429,9 @@ static int __init
> vxge_starter(void)
> {
> int ret = 0;
> - char version[32];
> - snprintf(version, 32, "%s", DRV_VERSION);
>
> - printk(KERN_INFO "%s: Copyright(c) 2002-2010 Exar Corp.\n",
> - VXGE_DRIVER_NAME);
> - printk(KERN_INFO "%s: Driver version: %s\n",
> - VXGE_DRIVER_NAME, version);
> + pr_info("Copyright(c) 2002-2010 Exar Corp.\n");
> + pr_info("Driver version: %s\n", DRV_VERSION);
>
> verify_bandwidth();
>
>
>
next prev parent reply other threads:[~2010-07-28 3:21 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-07-27 21:47 [PATCH net-next] drivers/net/vxge/vxge-main.c: Use pr_<level> and netdev_<level> Joe Perches
2010-07-28 3:21 ` Jon Mason [this message]
2010-07-31 6:28 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100728032117.GL28630@exar.com \
--to=jon.mason@exar.com \
--cc=Ramkrishna.Vepa@exar.com \
--cc=Sreenivasa.Honnur@exar.com \
--cc=davem@davemloft.net \
--cc=joe@perches.com \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).