From: Stephen Hemminger <shemminger@vyatta.com>
To: Jesse Gross <jesse@nicira.com>, David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Subject: [PATCH 2/2] sky2: convert to new VLAN model (v0.2)
Date: Fri, 7 Jan 2011 20:13:50 -0800 [thread overview]
Message-ID: <20110107201350.0be350bf@nehalam> (raw)
In-Reply-To: <AANLkTikwGQFByOZGgCCjTJySPa8QYndZ903CFmOkS1Ha@mail.gmail.com>
This converts sky2 to new VLAN offload flags control via ethtool.
It also allows for transmit offload of vlan tagged frames which
was not possible before.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
---
Changed the setting of vlan_features in this version to keep
non-offload settings (GRO|HIGHDMA) even if vlan offload is not
enabled.
--- a/drivers/net/sky2.c 2011-01-07 20:06:03.082168965 -0800
+++ b/drivers/net/sky2.c 2011-01-07 20:09:06.006180327 -0800
@@ -46,10 +46,6 @@
#include <asm/irq.h>
-#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
-#define SKY2_VLAN_TAG_USED 1
-#endif
-
#include "sky2.h"
#define DRV_NAME "sky2"
@@ -1326,39 +1322,34 @@ static int sky2_ioctl(struct net_device
return err;
}
-#ifdef SKY2_VLAN_TAG_USED
-static void sky2_set_vlan_mode(struct sky2_hw *hw, u16 port, bool onoff)
-{
- if (onoff) {
- sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T),
- RX_VLAN_STRIP_ON);
- sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T),
- TX_VLAN_TAG_ON);
- } else {
- sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T),
- RX_VLAN_STRIP_OFF);
- sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T),
- TX_VLAN_TAG_OFF);
- }
-}
+#define NETIF_F_ALL_VLAN (NETIF_F_HW_VLAN_TX|NETIF_F_HW_VLAN_RX)
-static void sky2_vlan_rx_register(struct net_device *dev, struct vlan_group *grp)
+static void sky2_vlan_mode(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
u16 port = sky2->port;
- netif_tx_lock_bh(dev);
- napi_disable(&hw->napi);
+ if (dev->features & NETIF_F_HW_VLAN_RX)
+ sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T),
+ RX_VLAN_STRIP_ON);
+ else
+ sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T),
+ RX_VLAN_STRIP_OFF);
- sky2->vlgrp = grp;
- sky2_set_vlan_mode(hw, port, grp != NULL);
+ dev->vlan_features = dev->features &~ NETIF_F_ALL_VLAN;
+ if (dev->features & NETIF_F_HW_VLAN_TX)
+ sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T),
+ TX_VLAN_TAG_ON);
+ else {
+ sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T),
+ TX_VLAN_TAG_OFF);
- sky2_read32(hw, B0_Y2_SP_LISR);
- napi_enable(&hw->napi);
- netif_tx_unlock_bh(dev);
+ /* Can't do transmit offload of vlan without hw vlan */
+ dev->vlan_features &= ~(NETIF_F_TSO | NETIF_F_SG
+ | NETIF_F_ALL_CSUM);
+ }
}
-#endif
/* Amount of required worst case padding in rx buffer */
static inline unsigned sky2_rx_pad(const struct sky2_hw *hw)
@@ -1635,9 +1626,7 @@ static void sky2_hw_up(struct sky2_port
sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
sky2->tx_ring_size - 1);
-#ifdef SKY2_VLAN_TAG_USED
- sky2_set_vlan_mode(hw, port, sky2->vlgrp != NULL);
-#endif
+ sky2_vlan_mode(sky2->netdev);
sky2_rx_start(sky2);
}
@@ -1780,7 +1769,7 @@ static netdev_tx_t sky2_xmit_frame(struc
}
ctrl = 0;
-#ifdef SKY2_VLAN_TAG_USED
+
/* Add VLAN tag, can piggyback on LRGLEN or ADDR64 */
if (vlan_tx_tag_present(skb)) {
if (!le) {
@@ -1792,7 +1781,6 @@ static netdev_tx_t sky2_xmit_frame(struc
le->length = cpu_to_be16(vlan_tx_tag_get(skb));
ctrl |= INS_VLAN;
}
-#endif
/* Handle TCP checksum offload */
if (skb->ip_summed == CHECKSUM_PARTIAL) {
@@ -2432,11 +2420,8 @@ static struct sk_buff *sky2_receive(stru
struct sk_buff *skb = NULL;
u16 count = (status & GMR_FS_LEN) >> 16;
-#ifdef SKY2_VLAN_TAG_USED
- /* Account for vlan tag */
- if (sky2->vlgrp && (status & GMR_FS_VLAN))
- count -= VLAN_HLEN;
-#endif
+ if (status & GMR_FS_VLAN)
+ count -= VLAN_HLEN; /* Account for vlan tag */
netif_printk(sky2, rx_status, KERN_DEBUG, dev,
"rx slot %u status 0x%x len %d\n",
@@ -2504,17 +2489,9 @@ static inline void sky2_tx_done(struct n
static inline void sky2_skb_rx(const struct sky2_port *sky2,
u32 status, struct sk_buff *skb)
{
-#ifdef SKY2_VLAN_TAG_USED
- u16 vlan_tag = be16_to_cpu(sky2->rx_tag);
- if (sky2->vlgrp && (status & GMR_FS_VLAN)) {
- if (skb->ip_summed == CHECKSUM_NONE)
- vlan_hwaccel_receive_skb(skb, sky2->vlgrp, vlan_tag);
- else
- vlan_gro_receive(&sky2->hw->napi, sky2->vlgrp,
- vlan_tag, skb);
- return;
- }
-#endif
+ if (status & GMR_FS_VLAN)
+ __vlan_hwaccel_put_tag(skb, be16_to_cpu(sky2->rx_tag));
+
if (skb->ip_summed == CHECKSUM_NONE)
netif_receive_skb(skb);
else
@@ -2631,7 +2608,6 @@ static int sky2_status_intr(struct sky2_
goto exit_loop;
break;
-#ifdef SKY2_VLAN_TAG_USED
case OP_RXVLAN:
sky2->rx_tag = length;
break;
@@ -2639,7 +2615,6 @@ static int sky2_status_intr(struct sky2_
case OP_RXCHKSVLAN:
sky2->rx_tag = length;
/* fall through */
-#endif
case OP_RXCHKS:
if (likely(sky2->flags & SKY2_FLAG_RX_CHECKSUM))
sky2_rx_checksum(sky2, status);
@@ -3042,6 +3017,10 @@ static int __devinit sky2_init(struct sk
| SKY2_HW_NEW_LE
| SKY2_HW_AUTO_TX_SUM
| SKY2_HW_ADV_POWER_CTL;
+
+ /* The workaround for status conflicts VLAN tag detection. */
+ if (hw->chip_rev == CHIP_REV_YU_FE2_A0)
+ hw->flags |= SKY2_HW_VLAN_BROKEN;
break;
case CHIP_ID_YUKON_SUPR:
@@ -4237,15 +4216,28 @@ static int sky2_set_eeprom(struct net_de
static int sky2_set_flags(struct net_device *dev, u32 data)
{
struct sky2_port *sky2 = netdev_priv(dev);
- u32 supported =
- (sky2->hw->flags & SKY2_HW_RSS_BROKEN) ? 0 : ETH_FLAG_RXHASH;
+ unsigned long old_feat = dev->features;
+ u32 supported = 0;
int rc;
+ if (!(sky2->hw->flags & SKY2_HW_RSS_BROKEN))
+ supported |= ETH_FLAG_RXHASH;
+
+ if (!(sky2->hw->flags & SKY2_HW_VLAN_BROKEN))
+ supported |= ETH_FLAG_RXVLAN | ETH_FLAG_TXVLAN;
+
+ printk(KERN_DEBUG "sky2 set_flags: supported %x data %x\n",
+ supported, data);
+
rc = ethtool_op_set_flags(dev, data, supported);
if (rc)
return rc;
- rx_set_rss(dev);
+ if ((old_feat ^ dev->features) & NETIF_F_RXHASH)
+ rx_set_rss(dev);
+
+ if ((old_feat ^ dev->features) & NETIF_F_ALL_VLAN)
+ sky2_vlan_mode(dev);
return 0;
}
@@ -4281,6 +4273,7 @@ static const struct ethtool_ops sky2_eth
.get_sset_count = sky2_get_sset_count,
.get_ethtool_stats = sky2_get_ethtool_stats,
.set_flags = sky2_set_flags,
+ .get_flags = ethtool_op_get_flags,
};
#ifdef CONFIG_SKY2_DEBUG
@@ -4562,9 +4555,6 @@ static const struct net_device_ops sky2_
.ndo_change_mtu = sky2_change_mtu,
.ndo_tx_timeout = sky2_tx_timeout,
.ndo_get_stats64 = sky2_get_stats,
-#ifdef SKY2_VLAN_TAG_USED
- .ndo_vlan_rx_register = sky2_vlan_rx_register,
-#endif
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_poll_controller = sky2_netpoll,
#endif
@@ -4580,9 +4570,6 @@ static const struct net_device_ops sky2_
.ndo_change_mtu = sky2_change_mtu,
.ndo_tx_timeout = sky2_tx_timeout,
.ndo_get_stats64 = sky2_get_stats,
-#ifdef SKY2_VLAN_TAG_USED
- .ndo_vlan_rx_register = sky2_vlan_rx_register,
-#endif
},
};
@@ -4633,7 +4620,8 @@ static __devinit struct net_device *sky2
sky2->port = port;
dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG
- | NETIF_F_TSO | NETIF_F_GRO;
+ | NETIF_F_TSO | NETIF_F_GRO;
+
if (highmem)
dev->features |= NETIF_F_HIGHDMA;
@@ -4641,13 +4629,8 @@ static __devinit struct net_device *sky2
if (!(hw->flags & SKY2_HW_RSS_BROKEN))
dev->features |= NETIF_F_RXHASH;
-#ifdef SKY2_VLAN_TAG_USED
- /* The workaround for FE+ status conflicts with VLAN tag detection. */
- if (!(sky2->hw->chip_id == CHIP_ID_YUKON_FE_P &&
- sky2->hw->chip_rev == CHIP_REV_YU_FE2_A0)) {
+ if (!(hw->flags & SKY2_HW_VLAN_BROKEN))
dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
- }
-#endif
/* read the mac address */
memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port * 8, ETH_ALEN);
--- a/drivers/net/sky2.h 2011-01-07 20:05:59.982101189 -0800
+++ b/drivers/net/sky2.h 2011-01-07 20:06:03.094169226 -0800
@@ -2236,11 +2236,8 @@ struct sky2_port {
u16 rx_pending;
u16 rx_data_size;
u16 rx_nfrags;
-
-#ifdef SKY2_VLAN_TAG_USED
u16 rx_tag;
- struct vlan_group *vlgrp;
-#endif
+
struct {
unsigned long last;
u32 mac_rp;
@@ -2284,6 +2281,7 @@ struct sky2_hw {
#define SKY2_HW_AUTO_TX_SUM 0x00000040 /* new IP decode for Tx */
#define SKY2_HW_ADV_POWER_CTL 0x00000080 /* additional PHY power regs */
#define SKY2_HW_RSS_BROKEN 0x00000100
+#define SKY2_HW_VLAN_BROKEN 0x00000200
u8 chip_id;
u8 chip_rev;
next prev parent reply other threads:[~2011-01-08 4:14 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-01-07 4:41 [PATCH 2/2] sky2: convert to new VLAN model Stephen Hemminger
2011-01-07 17:14 ` Jesse Gross
2011-01-07 17:27 ` Stephen Hemminger
2011-01-09 15:50 ` Jesse Gross
2011-01-08 4:13 ` Stephen Hemminger [this message]
2011-01-09 16:13 ` [PATCH 2/2] sky2: convert to new VLAN model (v0.2) Jesse Gross
2011-01-09 23:54 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20110107201350.0be350bf@nehalam \
--to=shemminger@vyatta.com \
--cc=davem@davemloft.net \
--cc=jesse@nicira.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).