From: Anton Blanchard <anton@samba.org>
To: Santiago Leon <santil@linux.vnet.ibm.com>,
brking@linux.vnet.ibm.com, rcj@linux.vnet.ibm.com,
mirq-linux@rere.qmqm.pl
Cc: netdev@vger.kernel.org
Subject: [PATCH 4/4] ibmveth: Fix checksum offload failure handling
Date: Thu, 08 Sep 2011 10:41:06 +1000 [thread overview]
Message-ID: <20110908004121.819855965@samba.org> (raw)
In-Reply-To: 20110908004102.355674129@samba.org
[-- Attachment #1: ibmveth_fix_csum2.patch --]
[-- Type: text/plain, Size: 2988 bytes --]
Fix a number of issues in ibmveth_set_csum_offload:
- set_attr6 and clr_attr6 may be used uninitialised
- We store the result of the IPV4 checksum change in ret but overwrite
it in a couple of places before checking it again later. Add ret4
to make it obvious what we are doing.
- We weren't clearing the NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM flags
if the enable of that hypervisor feature failed.
Signed-off-by: Anton Blanchard <anton@samba.org>
---
This patch could do with some review and I haven't marked it -stable
yet.
One thing that stands out is that we need to return an error back
through set_features if any feature bit gets changed.
Index: linux-build/drivers/net/ibmveth.c
===================================================================
--- linux-build.orig/drivers/net/ibmveth.c 2011-09-01 16:06:19.000000000 +1000
+++ linux-build/drivers/net/ibmveth.c 2011-09-02 09:05:57.585353722 +1000
@@ -757,7 +757,7 @@ static int ibmveth_set_csum_offload(stru
struct ibmveth_adapter *adapter = netdev_priv(dev);
unsigned long set_attr, clr_attr, ret_attr;
unsigned long set_attr6, clr_attr6;
- long ret, ret6;
+ long ret, ret4, ret6;
int rc1 = 0, rc2 = 0;
int restart = 0;
@@ -770,6 +770,8 @@ static int ibmveth_set_csum_offload(stru
set_attr = 0;
clr_attr = 0;
+ set_attr6 = 0;
+ clr_attr6 = 0;
if (data) {
set_attr = IBMVETH_ILLAN_IPV4_TCP_CSUM;
@@ -784,16 +786,20 @@ static int ibmveth_set_csum_offload(stru
if (ret == H_SUCCESS && !(ret_attr & IBMVETH_ILLAN_ACTIVE_TRUNK) &&
!(ret_attr & IBMVETH_ILLAN_TRUNK_PRI_MASK) &&
(ret_attr & IBMVETH_ILLAN_PADDED_PKT_CSUM)) {
- ret = h_illan_attributes(adapter->vdev->unit_address, clr_attr,
+ ret4 = h_illan_attributes(adapter->vdev->unit_address, clr_attr,
set_attr, &ret_attr);
- if (ret != H_SUCCESS) {
+ if (ret4 != H_SUCCESS) {
netdev_err(dev, "unable to change IPv4 checksum "
"offload settings. %d rc=%ld\n",
- data, ret);
+ data, ret4);
+
+ h_illan_attributes(adapter->vdev->unit_address,
+ set_attr, clr_attr, &ret_attr);
+
+ if (data == 1)
+ dev->features &= ~NETIF_F_IP_CSUM;
- ret = h_illan_attributes(adapter->vdev->unit_address,
- set_attr, clr_attr, &ret_attr);
} else {
adapter->fw_ipv4_csum_support = data;
}
@@ -804,15 +810,18 @@ static int ibmveth_set_csum_offload(stru
if (ret6 != H_SUCCESS) {
netdev_err(dev, "unable to change IPv6 checksum "
"offload settings. %d rc=%ld\n",
- data, ret);
+ data, ret6);
+
+ h_illan_attributes(adapter->vdev->unit_address,
+ set_attr6, clr_attr6, &ret_attr);
+
+ if (data == 1)
+ dev->features &= ~NETIF_F_IPV6_CSUM;
- ret = h_illan_attributes(adapter->vdev->unit_address,
- set_attr6, clr_attr6,
- &ret_attr);
} else
adapter->fw_ipv6_csum_support = data;
- if (ret == H_SUCCESS || ret6 == H_SUCCESS)
+ if (ret4 == H_SUCCESS || ret6 == H_SUCCESS)
adapter->rx_csum = data;
else
rc1 = -EIO;
next prev parent reply other threads:[~2011-09-08 0:45 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-08 0:41 [PATCH 0/4] ibmveth fixes Anton Blanchard
2011-09-08 0:41 ` [PATCH 1/4] ibmveth: Fix DMA unmap error Anton Blanchard
2011-09-08 0:41 ` [PATCH 2/4] ibmveth: Fix issue with DMA mapping failure Anton Blanchard
2011-09-08 0:41 ` [PATCH 3/4] ibmveth: Checksum offload is always disabled Anton Blanchard
2011-09-08 0:41 ` Anton Blanchard [this message]
2011-09-16 19:28 ` [PATCH 0/4] ibmveth fixes David Miller
2011-09-16 20:51 ` Anton Blanchard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20110908004121.819855965@samba.org \
--to=anton@samba.org \
--cc=brking@linux.vnet.ibm.com \
--cc=mirq-linux@rere.qmqm.pl \
--cc=netdev@vger.kernel.org \
--cc=rcj@linux.vnet.ibm.com \
--cc=santil@linux.vnet.ibm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).