[PATCH 02/14] atm/nicstar: don't use idr_remove_all()

[PATCH 02/14] atm/nicstar: don't use idr_remove_all()

[Tejun Heo]

idr_destroy() can destroy idr by itself and idr_remove_all() is being
deprecated.  Drop its usage.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Cc: netdev@vger.kernel.org
---
This patch depends on an earlier idr patch and given the trivial
nature of the patch, I think it would be best to route these together
through -mm.  Please holler if there's any objection.

Thanks.

 drivers/atm/nicstar.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/atm/nicstar.c b/drivers/atm/nicstar.c
index ed1d2b7..628787e 100644
--- a/drivers/atm/nicstar.c
+++ b/drivers/atm/nicstar.c
@@ -251,7 +251,6 @@ static void nicstar_remove_one(struct pci_dev *pcidev)
 		if (card->scd2vc[j] != NULL)
 			free_scq(card, card->scd2vc[j]->scq, card->scd2vc[j]->tx_vcc);
 	}
-	idr_remove_all(&card->idr);
 	idr_destroy(&card->idr);
 	pci_free_consistent(card->pcidev, NS_RSQSIZE + NS_RSQ_ALIGNMENT,
 			    card->rsq.org, card->rsq.dma);
-- 
1.8.1

Re: [PATCH 02/14] atm/nicstar: don't use idr_remove_all()

[David Miller]

From: Tejun Heo <tj@kernel.org>
Date: Fri, 25 Jan 2013 17:31:00 -0800

> idr_destroy() can destroy idr by itself and idr_remove_all() is being
> deprecated.  Drop its usage.
> 
> Signed-off-by: Tejun Heo <tj@kernel.org>
> Cc: Chas Williams <chas@cmf.nrl.navy.mil>
> Cc: netdev@vger.kernel.org
> ---
> This patch depends on an earlier idr patch and given the trivial
> nature of the patch, I think it would be best to route these together
> through -mm.  Please holler if there's any objection.

Please do:

Acked-by: David S. Miller <davem@davemloft.net>

[PATCH v2 02/14] atm/nicstar: don't use idr_remove_all()

[Tejun Heo]

Subject: atm/nicstar: convert to idr_alloc()

Convert to the much saner new idr interface.  The existing code looks
buggy to me - ID 0 is treated as no-ID but allocation specifies 0 as
lower limit and there's no error handling after partial success.  This
conversion keeps the bugs unchanged.

Only compile tested.

v2: id1 and id2 are now directly used for -errno return and thus
    should be signed.  Make them int instead of u32.  This was spotted
    by kbuild test robot.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: netdev@vger.kernel.org
---
 drivers/atm/nicstar.c |   29 +++++++++++++----------------
 1 file changed, 13 insertions(+), 16 deletions(-)

--- a/drivers/atm/nicstar.c
+++ b/drivers/atm/nicstar.c
@@ -949,7 +949,7 @@ static void free_scq(ns_dev *card, scq_i
 static void push_rxbufs(ns_dev * card, struct sk_buff *skb)
 {
 	struct sk_buff *handle1, *handle2;
-	u32 id1 = 0, id2 = 0;
+	int id1 = 0, id2 = 0;
 	u32 addr1, addr2;
 	u32 stat;
 	unsigned long flags;
@@ -1026,24 +1026,21 @@ static void push_rxbufs(ns_dev * card, s
 				card->lbfqc += 2;
 		}
 
-		do {
-			if (!idr_pre_get(&card->idr, GFP_ATOMIC)) {
-				printk(KERN_ERR
-				       "nicstar%d: no free memory for idr\n",
-				       card->index);
+		if (id1 < 0) {
+			id1 = idr_alloc(&card->idr, handle1, 0, 0, GFP_ATOMIC);
+			if (id1 < 0) {
+				err = id1;
 				goto out;
 			}
+		}
 
-			if (!id1)
-				err = idr_get_new_above(&card->idr, handle1, 0, &id1);
-
-			if (!id2 && err == 0)
-				err = idr_get_new_above(&card->idr, handle2, 0, &id2);
-
-		} while (err == -EAGAIN);
-
-		if (err)
-			goto out;
+		if (id2 < 0) {
+			id2 = idr_alloc(&card->idr, handle2, 0, 0, GFP_ATOMIC);
+			if (id2 < 0) {
+				err = id2;
+				goto out;
+			}
+		}
 
 		spin_lock_irqsave(&card->res_lock, flags);
 		while (CMD_BUSY(card)) ;

Re: [PATCH v2 02/14] atm/nicstar: don't use idr_remove_all()

[chas williams - CONTRACTOR]

On Mon, 4 Feb 2013 09:52:10 -0800
Tejun Heo <tj@kernel.org> wrote:

> Subject: atm/nicstar: convert to idr_alloc()
> 
> Convert to the much saner new idr interface.  The existing code looks
> buggy to me - ID 0 is treated as no-ID but allocation specifies 0 as
> lower limit and there's no error handling after partial success.  This
> conversion keeps the bugs unchanged.
> 
> Only compile tested.
> 
> v2: id1 and id2 are now directly used for -errno return and thus
>     should be signed.  Make them int instead of u32.  This was spotted
>     by kbuild test robot.
> 
> Signed-off-by: Tejun Heo <tj@kernel.org>
> Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
> Reported-by: kbuild test robot <fengguang.wu@intel.com>
> Cc: netdev@vger.kernel.org
> ---
>  drivers/atm/nicstar.c |   29 +++++++++++++----------------
>  1 file changed, 13 insertions(+), 16 deletions(-)
> 
> --- a/drivers/atm/nicstar.c
> +++ b/drivers/atm/nicstar.c
> @@ -949,7 +949,7 @@ static void free_scq(ns_dev *card, scq_i
>  static void push_rxbufs(ns_dev * card, struct sk_buff *skb)
>  {
>  	struct sk_buff *handle1, *handle2;
> -	u32 id1 = 0, id2 = 0;
> +	int id1 = 0, id2 = 0;
>  	u32 addr1, addr2;
>  	u32 stat;
>  	unsigned long flags;
> @@ -1026,24 +1026,21 @@ static void push_rxbufs(ns_dev * card, s
>  				card->lbfqc += 2;
>  		}
>  
> -		do {
> -			if (!idr_pre_get(&card->idr, GFP_ATOMIC)) {
> -				printk(KERN_ERR
> -				       "nicstar%d: no free memory for idr\n",
> -				       card->index);
> +		if (id1 < 0) {

you assign id1 to 0, so this never happens i think.  i don't think the
reason to preassign id1/id2 exists anymore once the do loop is removed.

> +			id1 = idr_alloc(&card->idr, handle1, 0, 0, GFP_ATOMIC);
> +			if (id1 < 0) {
> +				err = id1;

you dont need to assign err since it isn't returned.

>  				goto out;
>  			}
> +		}
>  
> -			if (!id1)
> -				err = idr_get_new_above(&card->idr, handle1, 0, &id1);
> -
> -			if (!id2 && err == 0)
> -				err = idr_get_new_above(&card->idr, handle2, 0, &id2);
> -
> -		} while (err == -EAGAIN);
> -
> -		if (err)
> -			goto out;
> +		if (id2 < 0) {

same as above.

> +			id2 = idr_alloc(&card->idr, handle2, 0, 0, GFP_ATOMIC);
> +			if (id2 < 0) {
> +				err = id2;
> +				goto out;
> +			}
> +		}
>  
>  		spin_lock_irqsave(&card->res_lock, flags);
>  		while (CMD_BUSY(card)) ;

Re: [PATCH v2 02/14] atm/nicstar: don't use idr_remove_all()

[Tejun Heo]

Hey,

On Mon, Feb 04, 2013 at 01:10:34PM -0500, chas williams - CONTRACTOR wrote:
> you assign id1 to 0, so this never happens i think.  i don't think the
> reason to preassign id1/id2 exists anymore once the do loop is removed.
> 
> > +			id1 = idr_alloc(&card->idr, handle1, 0, 0, GFP_ATOMIC);
> > +			if (id1 < 0) {
> > +				err = id1;
> 
> you dont need to assign err since it isn't returned.

Heh, I put v2 under the wrong thread.  I'll do v3 and post it under
v1.

Thanks.

-- 
tejun