Re: [BUG] bisected: PandaBoard smsc95xx ethernet driver error from USB timeout

[Mats Liljegren <liljegren.mats2@gmail.com>]

Frank Rowand wrote:
> On 03/21/13 07:41, Alan Stern wrote:
> > On Wed, 20 Mar 2013, Frank Rowand wrote:
> > 
> >> Hi All,
> >>
> >> Not quite sure quite where the problem is (USB, OMAP, smsc95xx driver, other???),
> >> so casting the nets wide...
> >>
> >> The PandaBoard frequently fails to boot with an eth0 error when mounting
> >> the root file system via NFS (ethernet driver fails due to a USB timeout;
> >> no ethernet means NFS won't work).  A typical set of error messages is:
> >>
> >> [    3.264373] smsc95xx 1-1.1:1.0: usb_probe_interface
> >> [    3.269500] smsc95xx 1-1.1:1.0: usb_probe_interface - got id
> >> [    3.275543] smsc95xx v1.0.4
> >> [    8.078674] smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-ehci-omap.0-1.1, smsc95xx USB 2.0 Ethernet, 82:b9:1d:fa:67:0d
> >> [    8.091003] hub 1-1:1.0: state 7 ports 5 chg 0000 evt 0002
> >> [   13.509918] usb 1-1.1: swapper/0 timed out on ep0out len=0/4
> >> [   13.515869] smsc95xx 1-1.1:1.0: eth0: Failed to write register index 0x00000108
> >> [   13.523559] smsc95xx 1-1.1:1.0: eth0: Failed to write ADDRL: -110
> >> [   13.529998] IP-Config: Failed to open eth0
> >>
> >> I have bisected this to:
> >>
> >>   commit 18aafe64d75d0e27dae206cacf4171e4e485d285
> >>   Author: Alan Stern <stern@rowland.harvard.edu>
> >>   Date:   Wed Jul 11 11:23:04 2012 -0400
> >>
> >>      USB: EHCI: use hrtimer for the I/O watchdog
> > 
> > I don't understand how that commit could cause a timeout unless there 
> > are at least two other bugs present in your system.
> > 
> >> Note that to compile this version of the kernel, an additional fix must
> >> also be applied:
> >>
> >>   commit ba5952e0711b14d8d4fe172671f8aa6091ace3ee
> >>   Author: Ming Lei <ming.lei@canonical.com>
> >>   Date:   Fri Jul 13 17:25:24 2012 +0800
> >>
> >>      USB: ehci-omap: fix compile failure(v1)
> >>
> >> The symptom can be worked around by retrying the USB access if a timeout
> >> occurs.  This is clearly _not_ the fix, just a hack that I used to
> >> investigate the problem:
> >>
> >>   http://article.gmane.org/gmane.linux.rt.user/9773
> >>
> >> My kernel configuration is:
> >>
> >>   arch/arm/configs/omap2plus_defconfig
> >>
> >>   plus to get the ethernet driver I add:
> >>
> >>     CONFIG_USB_EHCI_HCD
> >>     CONFIG_USB_NET_SMSC95XX
> >>
> >> I found the problem on 3.6.11, but have not replicated it on 3.9-rcX
> >> yet because my config fails to build on 3.9-rc1 and 3.9-rc2.  I'll try
> >> to work on that issue tomorrow.
> > 
> > Let me know how it works out.
> 
> My PandaBoard builds fail on 3.9-rcX due to ARM multiplatform issues.
> Either there is something I need to change about the way I build it,
> or it is broken (that is a side issue).  My simple expedient was to
> hack around multiplatform, and just make it build (patch below if
> anyone else wants a _temporary_ hack).

I have built 3.9-RC2 for PandaBoard ES and the only problem I have seen is
that you need to add "LOADADDR=0x80008000" when building uImage target.

-- Mats