From: Jarod Wilson <jarod@redhat.com>
To: linux-kernel@vger.kernel.org
Cc: Jarod Wilson <jarod@redhat.com>,
netdev@vger.kernel.org, Mirko Lindner <mlindner@marvell.com>,
Stephen Hemminger <stephen@networkplumber.org>,
Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Subject: [PATCH net-next 04/15] ethernet/marvell: use core min/max MTU checking
Date: Mon, 17 Oct 2016 15:54:06 -0400 [thread overview]
Message-ID: <20161017195417.48259-5-jarod@redhat.com> (raw)
In-Reply-To: <20161017195417.48259-1-jarod@redhat.com>
mvneta: min_mtu 68, max_mtu 9676
- mtu validation routine mostly did range check, merge back into
mvneta_change_mtu for simplicity
mvpp2: min_mtu 68, max_mtu 9676
- mtu validation routine mostly did range check, merge back into
mvpp2_change_mtu for simplicity
pxa168_eth: min_mtu 68, max_mtu 9500
skge: min_mtu 60, max_mtu 9000
sky2: min_mtu 68, max_mtu 1500 or 9000, depending on hw
CC: netdev@vger.kernel.org
CC: Mirko Lindner <mlindner@marvell.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
---
drivers/net/ethernet/marvell/mvneta.c | 36 +++++++++----------------------
drivers/net/ethernet/marvell/mvpp2.c | 36 ++++++++-----------------------
drivers/net/ethernet/marvell/pxa168_eth.c | 7 +++---
drivers/net/ethernet/marvell/skge.c | 7 +++---
drivers/net/ethernet/marvell/sky2.c | 18 +++++++---------
5 files changed, 35 insertions(+), 69 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index 5cb07c2..b85819e 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -3024,29 +3024,6 @@ static void mvneta_stop_dev(struct mvneta_port *pp)
mvneta_rx_reset(pp);
}
-/* Return positive if MTU is valid */
-static int mvneta_check_mtu_valid(struct net_device *dev, int mtu)
-{
- if (mtu < 68) {
- netdev_err(dev, "cannot change mtu to less than 68\n");
- return -EINVAL;
- }
-
- /* 9676 == 9700 - 20 and rounding to 8 */
- if (mtu > 9676) {
- netdev_info(dev, "Illegal MTU value %d, round to 9676\n", mtu);
- mtu = 9676;
- }
-
- if (!IS_ALIGNED(MVNETA_RX_PKT_SIZE(mtu), 8)) {
- netdev_info(dev, "Illegal MTU value %d, rounding to %d\n",
- mtu, ALIGN(MVNETA_RX_PKT_SIZE(mtu), 8));
- mtu = ALIGN(MVNETA_RX_PKT_SIZE(mtu), 8);
- }
-
- return mtu;
-}
-
static void mvneta_percpu_enable(void *arg)
{
struct mvneta_port *pp = arg;
@@ -3067,9 +3044,11 @@ static int mvneta_change_mtu(struct net_device *dev, int mtu)
struct mvneta_port *pp = netdev_priv(dev);
int ret;
- mtu = mvneta_check_mtu_valid(dev, mtu);
- if (mtu < 0)
- return -EINVAL;
+ if (!IS_ALIGNED(MVNETA_RX_PKT_SIZE(mtu), 8)) {
+ netdev_info(dev, "Illegal MTU value %d, rounding to %d\n",
+ mtu, ALIGN(MVNETA_RX_PKT_SIZE(mtu), 8));
+ mtu = ALIGN(MVNETA_RX_PKT_SIZE(mtu), 8);
+ }
dev->mtu = mtu;
@@ -4154,6 +4133,11 @@ static int mvneta_probe(struct platform_device *pdev)
dev->priv_flags |= IFF_UNICAST_FLT | IFF_LIVE_ADDR_CHANGE;
dev->gso_max_segs = MVNETA_MAX_TSO_SEGS;
+ /* MTU range: 68 - 9676 */
+ dev->min_mtu = ETH_MIN_MTU;
+ /* 9676 == 9700 - 20 and rounding to 8 */
+ dev->max_mtu = 9676;
+
err = register_netdev(dev);
if (err < 0) {
dev_err(&pdev->dev, "failed to register\n");
diff --git a/drivers/net/ethernet/marvell/mvpp2.c b/drivers/net/ethernet/marvell/mvpp2.c
index 60227a3..c8bf155 100644
--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -5453,29 +5453,6 @@ static void mvpp2_stop_dev(struct mvpp2_port *port)
phy_stop(ndev->phydev);
}
-/* Return positive if MTU is valid */
-static inline int mvpp2_check_mtu_valid(struct net_device *dev, int mtu)
-{
- if (mtu < 68) {
- netdev_err(dev, "cannot change mtu to less than 68\n");
- return -EINVAL;
- }
-
- /* 9676 == 9700 - 20 and rounding to 8 */
- if (mtu > 9676) {
- netdev_info(dev, "illegal MTU value %d, round to 9676\n", mtu);
- mtu = 9676;
- }
-
- if (!IS_ALIGNED(MVPP2_RX_PKT_SIZE(mtu), 8)) {
- netdev_info(dev, "illegal MTU value %d, round to %d\n", mtu,
- ALIGN(MVPP2_RX_PKT_SIZE(mtu), 8));
- mtu = ALIGN(MVPP2_RX_PKT_SIZE(mtu), 8);
- }
-
- return mtu;
-}
-
static int mvpp2_check_ringparam_valid(struct net_device *dev,
struct ethtool_ringparam *ring)
{
@@ -5717,10 +5694,10 @@ static int mvpp2_change_mtu(struct net_device *dev, int mtu)
struct mvpp2_port *port = netdev_priv(dev);
int err;
- mtu = mvpp2_check_mtu_valid(dev, mtu);
- if (mtu < 0) {
- err = mtu;
- goto error;
+ if (!IS_ALIGNED(MVPP2_RX_PKT_SIZE(mtu), 8)) {
+ netdev_info(dev, "illegal MTU value %d, round to %d\n", mtu,
+ ALIGN(MVPP2_RX_PKT_SIZE(mtu), 8));
+ mtu = ALIGN(MVPP2_RX_PKT_SIZE(mtu), 8);
}
if (!netif_running(dev)) {
@@ -6212,6 +6189,11 @@ static int mvpp2_port_probe(struct platform_device *pdev,
dev->hw_features |= features | NETIF_F_RXCSUM | NETIF_F_GRO;
dev->vlan_features |= features;
+ /* MTU range: 68 - 9676 */
+ dev->min_mtu = ETH_MIN_MTU;
+ /* 9676 == 9700 - 20 and rounding to 8 */
+ dev->max_mtu = 9676;
+
err = register_netdev(dev);
if (err < 0) {
dev_err(&pdev->dev, "failed to register netdev\n");
diff --git a/drivers/net/ethernet/marvell/pxa168_eth.c b/drivers/net/ethernet/marvell/pxa168_eth.c
index 5d5000c..b78a838 100644
--- a/drivers/net/ethernet/marvell/pxa168_eth.c
+++ b/drivers/net/ethernet/marvell/pxa168_eth.c
@@ -1209,9 +1209,6 @@ static int pxa168_eth_change_mtu(struct net_device *dev, int mtu)
int retval;
struct pxa168_eth_private *pep = netdev_priv(dev);
- if ((mtu > 9500) || (mtu < 68))
- return -EINVAL;
-
dev->mtu = mtu;
retval = set_port_config_ext(pep);
@@ -1459,6 +1456,10 @@ static int pxa168_eth_probe(struct platform_device *pdev)
dev->base_addr = 0;
dev->ethtool_ops = &pxa168_ethtool_ops;
+ /* MTU range: 68 - 9500 */
+ dev->min_mtu = ETH_MIN_MTU;
+ dev->max_mtu = 9500;
+
INIT_WORK(&pep->tx_timeout_task, pxa168_eth_tx_timeout_task);
if (pdev->dev.of_node)
diff --git a/drivers/net/ethernet/marvell/skge.c b/drivers/net/ethernet/marvell/skge.c
index 7173836..9c4b722 100644
--- a/drivers/net/ethernet/marvell/skge.c
+++ b/drivers/net/ethernet/marvell/skge.c
@@ -2900,9 +2900,6 @@ static int skge_change_mtu(struct net_device *dev, int new_mtu)
{
int err;
- if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
- return -EINVAL;
-
if (!netif_running(dev)) {
dev->mtu = new_mtu;
return 0;
@@ -3857,6 +3854,10 @@ static struct net_device *skge_devinit(struct skge_hw *hw, int port,
dev->watchdog_timeo = TX_WATCHDOG;
dev->irq = hw->pdev->irq;
+ /* MTU range: 60 - 9000 */
+ dev->min_mtu = ETH_ZLEN;
+ dev->max_mtu = ETH_JUMBO_MTU;
+
if (highmem)
dev->features |= NETIF_F_HIGHDMA;
diff --git a/drivers/net/ethernet/marvell/sky2.c b/drivers/net/ethernet/marvell/sky2.c
index f05ea56..aa60f4d 100644
--- a/drivers/net/ethernet/marvell/sky2.c
+++ b/drivers/net/ethernet/marvell/sky2.c
@@ -2398,16 +2398,6 @@ static int sky2_change_mtu(struct net_device *dev, int new_mtu)
u16 ctl, mode;
u32 imask;
- /* MTU size outside the spec */
- if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
- return -EINVAL;
-
- /* MTU > 1500 on yukon FE and FE+ not allowed */
- if (new_mtu > ETH_DATA_LEN &&
- (hw->chip_id == CHIP_ID_YUKON_FE ||
- hw->chip_id == CHIP_ID_YUKON_FE_P))
- return -EINVAL;
-
if (!netif_running(dev)) {
dev->mtu = new_mtu;
netdev_update_features(dev);
@@ -4808,6 +4798,14 @@ static struct net_device *sky2_init_netdev(struct sky2_hw *hw, unsigned port,
dev->features |= dev->hw_features;
+ /* MTU range: 60 - 1500 or 9000 */
+ dev->min_mtu = ETH_ZLEN;
+ if (hw->chip_id == CHIP_ID_YUKON_FE ||
+ hw->chip_id == CHIP_ID_YUKON_FE_P)
+ dev->max_mtu = ETH_DATA_LEN;
+ else
+ dev->max_mtu = ETH_JUMBO_MTU;
+
/* try to get mac address in the following order:
* 1) from device tree data
* 2) from internal registers set by bootloader
--
2.10.0
next prev parent reply other threads:[~2016-10-17 19:54 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-10-17 19:54 [PATCH net-next 00/15] ethernet: use core min/max MTU checking Jarod Wilson
2016-10-17 19:54 ` [PATCH net-next 01/15] ethernet/atheros: " Jarod Wilson
2016-10-17 19:54 ` [PATCH net-next 02/15] ethernet/broadcom: " Jarod Wilson
2016-10-17 19:54 ` [PATCH net-next 03/15] ethernet/intel: " Jarod Wilson
2016-10-17 20:20 ` Jakub Kicinski
2016-10-17 19:54 ` Jarod Wilson [this message]
2016-10-17 19:54 ` [PATCH net-next 05/15] ethernet/mellanox: " Jarod Wilson
2016-10-17 19:54 ` [PATCH net-next 06/15] ethernet/qlogic: " Jarod Wilson
2016-10-17 19:54 ` [PATCH net-next 07/15] ethernet/realtek: " Jarod Wilson
2016-10-17 19:54 ` [PATCH net-next 08/15] ethernet/sun: " Jarod Wilson
2016-10-17 19:54 ` [PATCH net-next 09/15] ethernet/dlink: " Jarod Wilson
2016-10-18 13:45 ` Denis Kirjanov
2016-10-18 15:04 ` Jarod Wilson
2016-10-22 9:54 ` Stefan Richter
2016-10-17 19:54 ` [PATCH net-next 10/15] ethernet/neterion: " Jarod Wilson
2016-10-17 19:54 ` [PATCH net-next 11/15] ethernet/cavium: " Jarod Wilson
2016-10-17 19:54 ` [PATCH net-next 12/15] ethernet/ibm: " Jarod Wilson
2016-10-17 19:54 ` [PATCH net-next 13/15] ethernet/tile: " Jarod Wilson
2016-10-17 19:54 ` [PATCH net-next 14/15] ethernet/toshiba: " Jarod Wilson
2016-10-17 19:54 ` [PATCH net-next 15/15] ethernet: " Jarod Wilson
2016-10-17 20:03 ` [PATCH net-next 00/15] " David Miller
2016-10-17 20:29 ` Jarod Wilson
2016-10-18 15:33 ` David Miller
2016-10-18 22:28 ` Jarod Wilson
2016-10-19 2:35 ` Jarod Wilson
2016-10-18 15:34 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20161017195417.48259-5-jarod@redhat.com \
--to=jarod@redhat.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mlindner@marvell.com \
--cc=netdev@vger.kernel.org \
--cc=stephen@networkplumber.org \
--cc=thomas.petazzoni@free-electrons.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).