[net-next 00/21][pull request] 10GbE Intel Wired LAN Driver Updates 2016-12-29

[net-next 00/21][pull request] 10GbE Intel Wired LAN Driver Updates 2016-12-29

[Jeff Kirsher]

This series contains updates to ixgbe and ixgbevf only.

Emil fixes ixgbe to use the NVM settings for FEC, so do not override the
settings.  Fixed the indirection table for x550, where newer devices can
support up to 64 RSS queues.  Extends the rtnl_lock() to protect the call
to netif_device_detach() and ixgbe_clear_interrupt_scheme() to avoid
against a double free WARN and/or a BUG in free_msi_irqs().  Fixed AER
error handling by making sure that the driver frees the IRQs in
ixgbe_io_error_detected() when responding to a PCIe AER error, and to
restore them when the interface recovers.

Tony updates the driver to report the driver version to the firmware using
the host interface command for x550 devices.  Fixed the PHY reset check
for x550em_ext_t PHY type.  Fixed bounds checking for x540 devices to
ensure the index is valid for the LED function.  Fixed the BaseT adapters
which support 100Mb capability and were not reporting the capability.

Ken Cox adds a missing check for the trusted bit before trying to set the
MACVLAN MAC address.

Yusuke Suzuki fixes an issue with 82599 and x540 devices where receive
timestamps were not working becase the bitwise operation for RX_HWSTAMP
falg was incorrect.

Don ensures that x553 KR/KX devices correctly advertise link speeds.
Adds the mailbox message to allow for VF promiscuous mode support.

Mark fixes two issues with EEPROM access, where the semaphore was not
being held until the entire response was read and the acquiring/releasing
of the semaphore is slow.  Cleaned up firmware version method and
functions which are no longer used.  Added new interfaces for firmware
commands to access some new PHYs.

The following are changes since commit 15d3afcc051f74d04a285c08594629172a1a9131:
  liquidio: optimize reads from Octeon PCI console
and are available in the git repository at:
  git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue 10GbE

Don Skidmore (3):
  ixgbe: Configure advertised speeds correctly for KR/KX backplane
  ixgbevf: Add support for VF promiscuous mode
  ixgbe: Add PF support for VF promiscuous mode

Emil Tantilov (7):
  ixgbe: do not disable FEC from the driver
  ixgbe: add mask for 64 RSS queues
  ixgbe: handle close/suspend race with netif_device_detach/present
  ixgbevf: handle race between close and suspend on shutdown
  ixgbe: fix AER error handling
  ixgbevf: fix AER error handling
  ixgbevf: restore hw_addr on resume or error

Ken Cox (1):
  ixgbe: test for trust in macvlan adjustments for VF

Mark Rustad (4):
  ixgbe: Fix issues with EEPROM access
  ixgbe: Remove unused firmware version functions and method
  ixgbe: Implement firmware interface to access some PHYs
  ixgbe: Implement support for firmware-controlled PHYs

Tony Nguyen (5):
  ixgbe: Report driver version to firmware for x550 devices
  ixgbe: Fix check for ixgbe_phy_x550em_ext_t reset
  ixgbe: Add bounds check for x540 LED functions
  ixgbe: Reduce I2C retry count on X550 devices
  ixgbe: Fix reporting of 100Mb capability

Yusuke Suzuki (1):
  ixgbe: Fix incorrect bitwise operations of PTP Rx timestamp flags

 drivers/net/ethernet/intel/ixgbe/ixgbe.h          |   5 +
 drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c    |   2 -
 drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c    |   2 -
 drivers/net/ethernet/intel/ixgbe/ixgbe_common.c   | 113 ++--
 drivers/net/ethernet/intel/ixgbe/ixgbe_common.h   |   6 +-
 drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c  | 153 +++++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c      |   8 +-
 drivers/net/ethernet/intel/ixgbe/ixgbe_main.c     |  92 +++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h      |   1 +
 drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c      |  66 +--
 drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h      |   4 -
 drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c      |  12 +-
 drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c    |  50 +-
 drivers/net/ethernet/intel/ixgbe/ixgbe_type.h     |  90 +++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c     |  10 +-
 drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c     | 594 +++++++++++++++++++---
 drivers/net/ethernet/intel/ixgbevf/ixgbevf.h      |   1 +
 drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c |  66 ++-
 drivers/net/ethernet/intel/ixgbevf/mbx.h          |   1 +
 drivers/net/ethernet/intel/ixgbevf/vf.c           |  24 +-
 20 files changed, 1101 insertions(+), 199 deletions(-)

-- 
2.9.3

[net-next 01/21] ixgbe: do not disable FEC from the driver

[Jeff Kirsher]

From: Emil Tantilov <emil.s.tantilov@intel.com>

FEC is configured by the NVM and the driver should not be
overriding it.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index 11fb433..f06b0e1 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -2108,8 +2108,6 @@ static s32 ixgbe_setup_kr_speed_x550em(struct ixgbe_hw *hw,
 		return status;
 
 	reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
-	reg_val &= ~(IXGBE_KRM_LINK_CTRL_1_TETH_AN_FEC_REQ |
-		     IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC);
 	reg_val &= ~(IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KR |
 		     IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KX);
 
-- 
2.9.3

[net-next 02/21] ixgbe: Report driver version to firmware for x550 devices

[Jeff Kirsher]

From: Tony Nguyen <anthony.l.nguyen@intel.com>

Some x550 devices require the driver version reported to its firmware; this
patch sends the driver version string to the firmware through the host
interface command for x550 devices.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_common.c |  7 ++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_common.h |  3 +-
 drivers/net/ethernet/intel/ixgbe/ixgbe_main.c   |  5 ++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_type.h   | 14 +++++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c   | 58 ++++++++++++++++++++++++-
 5 files changed, 80 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
index 8832df3..5d8f1ae 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
@@ -3578,7 +3578,7 @@ void ixgbe_set_rxpba_generic(struct ixgbe_hw *hw,
  *  Calculates the checksum for some buffer on a specified length.  The
  *  checksum calculated is returned.
  **/
-static u8 ixgbe_calculate_checksum(u8 *buffer, u32 length)
+u8 ixgbe_calculate_checksum(u8 *buffer, u32 length)
 {
 	u32 i;
 	u8 sum = 0;
@@ -3722,6 +3722,8 @@ s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
  *  @min: driver version minor number
  *  @build: driver version build number
  *  @sub: driver version sub build number
+ *  @len: length of driver_ver string
+ *  @driver_ver: driver string
  *
  *  Sends driver version number to firmware through the manageability
  *  block.  On success return 0
@@ -3729,7 +3731,8 @@ s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
  *  semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
  **/
 s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
-				 u8 build, u8 sub)
+				 u8 build, u8 sub, __always_unused u16 len,
+				 __always_unused const char *driver_ver)
 {
 	struct ixgbe_hic_drv_info fw_cmd;
 	int i;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
index 5b3e3c6..393aeab 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
@@ -111,7 +111,8 @@ void ixgbe_set_mac_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf);
 void ixgbe_set_vlan_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf);
 s32 ixgbe_get_device_caps_generic(struct ixgbe_hw *hw, u16 *device_caps);
 s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
-				 u8 build, u8 ver);
+				 u8 build, u8 ver, u16 len, const char *str);
+u8 ixgbe_calculate_checksum(u8 *buffer, u32 length);
 s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *, u32 length,
 				 u32 timeout, bool return_data);
 void ixgbe_clear_tx_pending(struct ixgbe_hw *hw);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
index 1e2f39e..6732c90 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -9833,8 +9833,9 @@ static int ixgbe_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	 * since os does not support feature
 	 */
 	if (hw->mac.ops.set_fw_drv_ver)
-		hw->mac.ops.set_fw_drv_ver(hw, 0xFF, 0xFF, 0xFF,
-					   0xFF);
+		hw->mac.ops.set_fw_drv_ver(hw, 0xFF, 0xFF, 0xFF, 0xFF,
+					   sizeof(ixgbe_driver_version) - 1,
+					   ixgbe_driver_version);
 
 	/* add san mac addr to netdev */
 	ixgbe_add_sanmac_netdev(netdev);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
index cf21273..0d85511 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
@@ -2619,6 +2619,7 @@ enum ixgbe_fdir_pballoc_type {
 #define FW_CEM_UNUSED_VER		0x0
 #define FW_CEM_MAX_RETRIES		3
 #define FW_CEM_RESP_STATUS_SUCCESS	0x1
+#define FW_CEM_DRIVER_VERSION_SIZE	39 /* +9 would send 48 bytes to fw */
 #define FW_READ_SHADOW_RAM_CMD		0x31
 #define FW_READ_SHADOW_RAM_LEN		0x6
 #define FW_WRITE_SHADOW_RAM_CMD		0x33
@@ -2686,6 +2687,16 @@ struct ixgbe_hic_drv_info {
 	u16 pad2; /* end spacing to ensure length is mult. of dword2 */
 };
 
+struct ixgbe_hic_drv_info2 {
+	struct ixgbe_hic_hdr hdr;
+	u8 port_num;
+	u8 ver_sub;
+	u8 ver_build;
+	u8 ver_min;
+	u8 ver_maj;
+	char driver_string[FW_CEM_DRIVER_VERSION_SIZE];
+};
+
 /* These need to be dword aligned */
 struct ixgbe_hic_read_shadow_ram {
 	union ixgbe_hic_hdr2 hdr;
@@ -3362,7 +3373,8 @@ struct ixgbe_mac_operations {
 	void (*fc_autoneg)(struct ixgbe_hw *);
 
 	/* Manageability interface */
-	s32 (*set_fw_drv_ver)(struct ixgbe_hw *, u8, u8, u8, u8);
+	s32 (*set_fw_drv_ver)(struct ixgbe_hw *, u8, u8, u8, u8, u16,
+			      const char *);
 	s32 (*get_thermal_sensor_data)(struct ixgbe_hw *);
 	s32 (*init_thermal_sensor_thresh)(struct ixgbe_hw *hw);
 	void (*disable_rx)(struct ixgbe_hw *hw);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index f06b0e1..92f2b5e 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -2354,6 +2354,62 @@ static s32 ixgbe_led_off_t_x550em(struct ixgbe_hw *hw, u32 led_idx)
 	return 0;
 }
 
+/**
+ *  ixgbe_set_fw_drv_ver_x550 - Sends driver version to firmware
+ *  @hw: pointer to the HW structure
+ *  @maj: driver version major number
+ *  @min: driver version minor number
+ *  @build: driver version build number
+ *  @sub: driver version sub build number
+ *  @len: length of driver_ver string
+ *  @driver_ver: driver string
+ *
+ *  Sends driver version number to firmware through the manageability
+ *  block.  On success return 0
+ *  else returns IXGBE_ERR_SWFW_SYNC when encountering an error acquiring
+ *  semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
+ **/
+static s32 ixgbe_set_fw_drv_ver_x550(struct ixgbe_hw *hw, u8 maj, u8 min,
+				     u8 build, u8 sub, u16 len,
+				     const char *driver_ver)
+{
+	struct ixgbe_hic_drv_info2 fw_cmd;
+	s32 ret_val;
+	int i;
+
+	if (!len || !driver_ver || (len > sizeof(fw_cmd.driver_string)))
+		return IXGBE_ERR_INVALID_ARGUMENT;
+
+	fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO;
+	fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN + len;
+	fw_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED;
+	fw_cmd.port_num = (u8)hw->bus.func;
+	fw_cmd.ver_maj = maj;
+	fw_cmd.ver_min = min;
+	fw_cmd.ver_build = build;
+	fw_cmd.ver_sub = sub;
+	fw_cmd.hdr.checksum = 0;
+	memcpy(fw_cmd.driver_string, driver_ver, len);
+	fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd,
+			      (FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len));
+
+	for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) {
+		ret_val = ixgbe_host_interface_command(hw, (u32 *)&fw_cmd,
+						       sizeof(fw_cmd),
+						       IXGBE_HI_COMMAND_TIMEOUT,
+						       true);
+		if (ret_val)
+			continue;
+
+		if (fw_cmd.hdr.cmd_or_resp.ret_status !=
+		    FW_CEM_RESP_STATUS_SUCCESS)
+			return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+		return 0;
+	}
+
+	return ret_val;
+}
+
 /** ixgbe_get_lcd_x550em - Determine lowest common denominator
  *  @hw: pointer to hardware structure
  *  @lcd_speed: pointer to lowest common link speed
@@ -3273,7 +3329,7 @@ static s32 ixgbe_write_phy_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr,
 	.clear_vfta			= &ixgbe_clear_vfta_generic, \
 	.set_vfta			= &ixgbe_set_vfta_generic, \
 	.fc_enable			= &ixgbe_fc_enable_generic, \
-	.set_fw_drv_ver			= &ixgbe_set_fw_drv_ver_generic, \
+	.set_fw_drv_ver			= &ixgbe_set_fw_drv_ver_x550, \
 	.init_uta_tables		= &ixgbe_init_uta_tables_generic, \
 	.set_mac_anti_spoofing		= &ixgbe_set_mac_anti_spoofing, \
 	.set_vlan_anti_spoofing		= &ixgbe_set_vlan_anti_spoofing, \
-- 
2.9.3

[net-next 03/21] ixgbe: Fix check for ixgbe_phy_x550em_ext_t reset

[Jeff Kirsher]

From: Tony Nguyen <anthony.l.nguyen@intel.com>

The generic PHY reset check we had previously is not sufficient for the
ixgbe_phy_x550em_ext_t PHY type.  Check 1.CC02.0 instead - same as
ixgbe_init_ext_t_x550().

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c | 25 +++++++++++++++++++++----
 1 file changed, 21 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
index 3b83620..b272938 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
@@ -452,10 +452,27 @@ s32 ixgbe_reset_phy_generic(struct ixgbe_hw *hw)
 	 */
 	for (i = 0; i < 30; i++) {
 		msleep(100);
-		hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS, &ctrl);
-		if (!(ctrl & MDIO_CTRL1_RESET)) {
-			udelay(2);
-			break;
+		if (hw->phy.type == ixgbe_phy_x550em_ext_t) {
+			status = hw->phy.ops.read_reg(hw,
+						  IXGBE_MDIO_TX_VENDOR_ALARMS_3,
+						  MDIO_MMD_PMAPMD, &ctrl);
+			if (status)
+				return status;
+
+			if (ctrl & IXGBE_MDIO_TX_VENDOR_ALARMS_3_RST_MASK) {
+				udelay(2);
+				break;
+			}
+		} else {
+			status = hw->phy.ops.read_reg(hw, MDIO_CTRL1,
+						      MDIO_MMD_PHYXS, &ctrl);
+			if (status)
+				return status;
+
+			if (!(ctrl & MDIO_CTRL1_RESET)) {
+				udelay(2);
+				break;
+			}
 		}
 	}
 
-- 
2.9.3

[net-next 04/21] ixgbe: add mask for 64 RSS queues

[Jeff Kirsher]

From: Emil Tantilov <emil.s.tantilov@intel.com>

The indirection table was reported incorrectly for X550 and newer
where we can support up to 64 RSS queues.

Reported-by Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c
index 15ab337..10d2967 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c
@@ -308,6 +308,7 @@ static void ixgbe_cache_ring_register(struct ixgbe_adapter *adapter)
 	ixgbe_cache_ring_rss(adapter);
 }
 
+#define IXGBE_RSS_64Q_MASK	0x3F
 #define IXGBE_RSS_16Q_MASK	0xF
 #define IXGBE_RSS_8Q_MASK	0x7
 #define IXGBE_RSS_4Q_MASK	0x3
@@ -604,6 +605,7 @@ static bool ixgbe_set_sriov_queues(struct ixgbe_adapter *adapter)
  **/
 static bool ixgbe_set_rss_queues(struct ixgbe_adapter *adapter)
 {
+	struct ixgbe_hw *hw = &adapter->hw;
 	struct ixgbe_ring_feature *f;
 	u16 rss_i;
 
@@ -612,7 +614,11 @@ static bool ixgbe_set_rss_queues(struct ixgbe_adapter *adapter)
 	rss_i = f->limit;
 
 	f->indices = rss_i;
-	f->mask = IXGBE_RSS_16Q_MASK;
+
+	if (hw->mac.type < ixgbe_mac_X550)
+		f->mask = IXGBE_RSS_16Q_MASK;
+	else
+		f->mask = IXGBE_RSS_64Q_MASK;
 
 	/* disable ATR by default, it will be configured below */
 	adapter->flags &= ~IXGBE_FLAG_FDIR_HASH_CAPABLE;
-- 
2.9.3

[net-next 05/21] ixgbe: Add bounds check for x540 LED functions

[Jeff Kirsher]

From: Tony Nguyen <anthony.l.nguyen@intel.com>

This is an extension of commit 003287e0f087 ("ixgbevf: Correct parameter
sent to LED function"); add bounds checking to x540 functions to ensure the
index is valid.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
index e2ff823..afc4d16 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
@@ -780,8 +780,10 @@ s32 ixgbe_blink_led_start_X540(struct ixgbe_hw *hw, u32 index)
 	ixgbe_link_speed speed;
 	bool link_up;
 
-	/*
-	 * Link should be up in order for the blink bit in the LED control
+	if (index > 3)
+		return IXGBE_ERR_PARAM;
+
+	/* Link should be up in order for the blink bit in the LED control
 	 * register to work. Force link and speed in the MAC if link is down.
 	 * This will be reversed when we stop the blinking.
 	 */
@@ -814,6 +816,9 @@ s32 ixgbe_blink_led_stop_X540(struct ixgbe_hw *hw, u32 index)
 	u32 macc_reg;
 	u32 ledctl_reg;
 
+	if (index > 3)
+		return IXGBE_ERR_PARAM;
+
 	/* Restore the LED to its default value. */
 	ledctl_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
 	ledctl_reg &= ~IXGBE_LED_MODE_MASK(index);
-- 
2.9.3

[net-next 06/21] ixgbe: Reduce I2C retry count on X550 devices

[Jeff Kirsher]

From: Tony Nguyen <anthony.l.nguyen@intel.com>

A retry count of 10 is likely to run into problems on X550 devices that
have to detect and reset unresponsive CS4227 devices. So, reduce the I2C
retry count to 3 for X550 and above. This should avoid any possible
regressions in existing devices.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
index b272938..019b3c2 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
@@ -113,7 +113,7 @@ s32 ixgbe_read_i2c_combined_generic_int(struct ixgbe_hw *hw, u8 addr,
 					u16 reg, u16 *val, bool lock)
 {
 	u32 swfw_mask = hw->phy.phy_semaphore_mask;
-	int max_retry = 10;
+	int max_retry = 3;
 	int retry = 0;
 	u8 csum_byte;
 	u8 high_bits;
@@ -1755,6 +1755,8 @@ static s32 ixgbe_read_i2c_byte_generic_int(struct ixgbe_hw *hw, u8 byte_offset,
 	u32 swfw_mask = hw->phy.phy_semaphore_mask;
 	bool nack = true;
 
+	if (hw->mac.type >= ixgbe_mac_X550)
+		max_retry = 3;
 	if (ixgbe_is_sfp_probe(hw, byte_offset, dev_addr))
 		max_retry = IXGBE_SFP_DETECT_RETRIES;
 
-- 
2.9.3

[net-next 07/21] ixgbe: Fix reporting of 100Mb capability

[Jeff Kirsher]

From: Tony Nguyen <anthony.l.nguyen@intel.com>

BaseT adapters that are capable of supporting 100Mb are not reporting this
capability.  This patch corrects the reporting so that 100Mb is shown as
supported on those adapters.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
index fd192bf..8789f21 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
@@ -199,7 +199,7 @@ static int ixgbe_get_settings(struct net_device *netdev,
 	if (supported_link & IXGBE_LINK_SPEED_100_FULL)
 		ecmd->supported |= ixgbe_isbackplane(hw->phy.media_type) ?
 				   SUPPORTED_1000baseKX_Full :
-				   SUPPORTED_1000baseT_Full;
+				   SUPPORTED_100baseT_Full;
 
 	/* default advertised speed if phy.autoneg_advertised isn't set */
 	ecmd->advertising = ecmd->supported;
-- 
2.9.3

[net-next 08/21] ixgbe: handle close/suspend race with netif_device_detach/present

[Jeff Kirsher]

From: Emil Tantilov <emil.s.tantilov@intel.com>

When an interface is part of a namespace it is possible that
ixgbe_close() may be called while __ixgbe_shutdown() is running
which ends up in a double free WARN and/or a BUG in free_msi_irqs().

To handle this situation we extend the rtnl_lock() to protect the
call to netif_device_detach() and ixgbe_clear_interrupt_scheme()
in __ixgbe_shutdown() and check for netif_device_present()
to avoid clearing the interrupts second time in ixgbe_close();

Also extend the rtnl lock in ixgbe_resume() to netif_device_attach().

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 17 ++++++++---------
 1 file changed, 8 insertions(+), 9 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
index 6732c90..476f012 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -6200,7 +6200,8 @@ int ixgbe_close(struct net_device *netdev)
 
 	ixgbe_ptp_stop(adapter);
 
-	ixgbe_close_suspend(adapter);
+	if (netif_device_present(netdev))
+		ixgbe_close_suspend(adapter);
 
 	ixgbe_fdir_filter_exit(adapter);
 
@@ -6245,14 +6246,12 @@ static int ixgbe_resume(struct pci_dev *pdev)
 	if (!err && netif_running(netdev))
 		err = ixgbe_open(netdev);
 
-	rtnl_unlock();
 
-	if (err)
-		return err;
-
-	netif_device_attach(netdev);
+	if (!err)
+		netif_device_attach(netdev);
+	rtnl_unlock();
 
-	return 0;
+	return err;
 }
 #endif /* CONFIG_PM */
 
@@ -6267,14 +6266,14 @@ static int __ixgbe_shutdown(struct pci_dev *pdev, bool *enable_wake)
 	int retval = 0;
 #endif
 
+	rtnl_lock();
 	netif_device_detach(netdev);
 
-	rtnl_lock();
 	if (netif_running(netdev))
 		ixgbe_close_suspend(adapter);
-	rtnl_unlock();
 
 	ixgbe_clear_interrupt_scheme(adapter);
+	rtnl_unlock();
 
 #ifdef CONFIG_PM
 	retval = pci_save_state(pdev);
-- 
2.9.3

[net-next 09/21] ixgbevf: handle race between close and suspend on shutdown

[Jeff Kirsher]

From: Emil Tantilov <emil.s.tantilov@intel.com>

When an interface is part of a namespace it is possible that
ixgbevf_close() may be called while ixgbevf_suspend() is running
which ends up in a double free WARN and/or a BUG in free_msi_irqs()

To handle this situation we extend the rtnl_lock() to protect the
call to netif_device_detach() and check for !netif_device_present()
to avoid entering close while in suspend.

Also added rtnl locks to ixgbevf_queue_reset_subtask().

CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
index 6d4bef5..8574f21 100644
--- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
+++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
@@ -3242,6 +3242,9 @@ int ixgbevf_close(struct net_device *netdev)
 {
 	struct ixgbevf_adapter *adapter = netdev_priv(netdev);
 
+	if (!netif_device_present(netdev))
+		return 0;
+
 	ixgbevf_down(adapter);
 	ixgbevf_free_irq(adapter);
 
@@ -3268,6 +3271,8 @@ static void ixgbevf_queue_reset_subtask(struct ixgbevf_adapter *adapter)
 	 * match packet buffer alignment. Unfortunately, the
 	 * hardware is not flexible enough to do this dynamically.
 	 */
+	rtnl_lock();
+
 	if (netif_running(dev))
 		ixgbevf_close(dev);
 
@@ -3276,6 +3281,8 @@ static void ixgbevf_queue_reset_subtask(struct ixgbevf_adapter *adapter)
 
 	if (netif_running(dev))
 		ixgbevf_open(dev);
+
+	rtnl_unlock();
 }
 
 static void ixgbevf_tx_ctxtdesc(struct ixgbevf_ring *tx_ring,
@@ -3796,17 +3803,17 @@ static int ixgbevf_suspend(struct pci_dev *pdev, pm_message_t state)
 	int retval = 0;
 #endif
 
+	rtnl_lock();
 	netif_device_detach(netdev);
 
 	if (netif_running(netdev)) {
-		rtnl_lock();
 		ixgbevf_down(adapter);
 		ixgbevf_free_irq(adapter);
 		ixgbevf_free_all_tx_resources(adapter);
 		ixgbevf_free_all_rx_resources(adapter);
 		ixgbevf_clear_interrupt_scheme(adapter);
-		rtnl_unlock();
 	}
+	rtnl_unlock();
 
 #ifdef CONFIG_PM
 	retval = pci_save_state(pdev);
-- 
2.9.3

[net-next 10/21] ixgbe: test for trust in macvlan adjustments for VF

[Jeff Kirsher]

From: Ken Cox <jkc@redhat.com>

There are two methods for setting mac addresses in a Macvlan, that
differentiate themselves in the function macvlan_set_mac_Address.
If the macvlan mode is passthru, then we use the dev_set_mac_address
method, otherwise we use the dev_uc api via macvlan_sync_addresses.
The latter method (which would stem from using any non-passthru mode,
like bridge, or vepa), calls down into the driver in a path that terminates
in ixgbevf_set_uc_addr_vf, which sends a IXGBE_VF_SET_MACVLAN message,
which causes the pf to spawn the noted error message.  This occurs because
it appears that the guest is trying to delete the mac address of the macvlan
before adding another.

The other path in macvlan_set_mac_address uses dev_set_mac_address, which
calls into ixgbevf_set_mac which uses the IXGBE_VF_SET_MAC_ADDR to the
pf to set the macvlan mac address.

The discrepancy here is in the handlers.  The handler function for
IXGBE_VF_SET_MAC_ADDR (ixgbe_set_vf_mac_addr) has a check for
the vfinfo[].trusted bit to allow the operation if the vf is trusted.
In comparison, the IXGBE_VF_SET_MACVLAN message handler
(ixgbe_set_vf_macvlan_msg) has no such check of the trusted bit.

Signed-off-by: Ken Cox <jkc@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c
index 7e5d985..dd1187c 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c
@@ -934,7 +934,8 @@ static int ixgbe_set_vf_macvlan_msg(struct ixgbe_adapter *adapter,
 		    IXGBE_VT_MSGINFO_SHIFT;
 	int err;
 
-	if (adapter->vfinfo[vf].pf_set_mac && index > 0) {
+	if (adapter->vfinfo[vf].pf_set_mac && !adapter->vfinfo[vf].trusted &&
+	    index > 0) {
 		e_warn(drv,
 		       "VF %d requested MACVLAN filter but is administratively denied\n",
 		       vf);
-- 
2.9.3

[net-next 11/21] ixgbe: fix AER error handling

[Jeff Kirsher]

From: Emil Tantilov <emil.s.tantilov@intel.com>

Make sure that we free the IRQs in ixgbe_io_error_detected() when
responding to an PCIe AER error and also restore them when the
interface recovers from it.

Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
in the case where we call ixgbe_remove() after a failed recovery from
AER error because the interrupts were not freed.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
index 476f012..9ca167c 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -10082,7 +10082,7 @@ static pci_ers_result_t ixgbe_io_error_detected(struct pci_dev *pdev,
 	}
 
 	if (netif_running(netdev))
-		ixgbe_down(adapter);
+		ixgbe_close_suspend(adapter);
 
 	if (!test_and_set_bit(__IXGBE_DISABLED, &adapter->state))
 		pci_disable_device(pdev);
@@ -10152,10 +10152,12 @@ static void ixgbe_io_resume(struct pci_dev *pdev)
 	}
 
 #endif
+	rtnl_lock();
 	if (netif_running(netdev))
-		ixgbe_up(adapter);
+		ixgbe_open(netdev);
 
 	netif_device_attach(netdev);
+	rtnl_unlock();
 }
 
 static const struct pci_error_handlers ixgbe_err_handler = {
-- 
2.9.3

[net-next 12/21] ixgbevf: fix AER error handling

[Jeff Kirsher]

From: Emil Tantilov <emil.s.tantilov@intel.com>

Make sure that we free the IRQs in ixgbevf_io_error_detected() when
responding to an PCIe AER error and also restore them when the
interface recovers from it.

Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
in the case where we call ixgbevf_remove() after a failed recovery from
AER error because the interrupts were not freed.

Also moved the down and free functions into ixgbevf_close_suspend()
same as with ixgbe.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 43 +++++++++++++----------
 1 file changed, 25 insertions(+), 18 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
index 8574f21..7dfd1df 100644
--- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
+++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
@@ -3228,6 +3228,21 @@ int ixgbevf_open(struct net_device *netdev)
 }
 
 /**
+ * ixgbevf_close_suspend - actions necessary to both suspend and close flows
+ * @adapter: the private adapter struct
+ *
+ * This function should contain the necessary work common to both suspending
+ * and closing of the device.
+ */
+static void ixgbevf_close_suspend(struct ixgbevf_adapter *adapter)
+{
+		ixgbevf_down(adapter);
+		ixgbevf_free_irq(adapter);
+		ixgbevf_free_all_tx_resources(adapter);
+		ixgbevf_free_all_rx_resources(adapter);
+}
+
+/**
  * ixgbevf_close - Disables a network interface
  * @netdev: network interface device structure
  *
@@ -3242,14 +3257,8 @@ int ixgbevf_close(struct net_device *netdev)
 {
 	struct ixgbevf_adapter *adapter = netdev_priv(netdev);
 
-	if (!netif_device_present(netdev))
-		return 0;
-
-	ixgbevf_down(adapter);
-	ixgbevf_free_irq(adapter);
-
-	ixgbevf_free_all_tx_resources(adapter);
-	ixgbevf_free_all_rx_resources(adapter);
+	if (netif_device_present(netdev))
+		ixgbevf_close_suspend(adapter);
 
 	return 0;
 }
@@ -3806,13 +3815,10 @@ static int ixgbevf_suspend(struct pci_dev *pdev, pm_message_t state)
 	rtnl_lock();
 	netif_device_detach(netdev);
 
-	if (netif_running(netdev)) {
-		ixgbevf_down(adapter);
-		ixgbevf_free_irq(adapter);
-		ixgbevf_free_all_tx_resources(adapter);
-		ixgbevf_free_all_rx_resources(adapter);
-		ixgbevf_clear_interrupt_scheme(adapter);
-	}
+	if (netif_running(netdev))
+		ixgbevf_close_suspend(adapter);
+
+	ixgbevf_clear_interrupt_scheme(adapter);
 	rtnl_unlock();
 
 #ifdef CONFIG_PM
@@ -4251,7 +4257,7 @@ static pci_ers_result_t ixgbevf_io_error_detected(struct pci_dev *pdev,
 	}
 
 	if (netif_running(netdev))
-		ixgbevf_down(adapter);
+		ixgbevf_close_suspend(adapter);
 
 	if (!test_and_set_bit(__IXGBEVF_DISABLED, &adapter->state))
 		pci_disable_device(pdev);
@@ -4299,12 +4305,13 @@ static pci_ers_result_t ixgbevf_io_slot_reset(struct pci_dev *pdev)
 static void ixgbevf_io_resume(struct pci_dev *pdev)
 {
 	struct net_device *netdev = pci_get_drvdata(pdev);
-	struct ixgbevf_adapter *adapter = netdev_priv(netdev);
 
+	rtnl_lock();
 	if (netif_running(netdev))
-		ixgbevf_up(adapter);
+		ixgbevf_open(netdev);
 
 	netif_device_attach(netdev);
+	rtnl_unlock();
 }
 
 /* PCI Error Recovery (ERS) */
-- 
2.9.3

Re: [net-next 12/21] ixgbevf: fix AER error handling

[Sergei Shtylyov]

Hello!

On 12/30/2016 12:33 PM, Jeff Kirsher wrote:

> From: Emil Tantilov <emil.s.tantilov@intel.com>
>
> Make sure that we free the IRQs in ixgbevf_io_error_detected() when
> responding to an PCIe AER error and also restore them when the
> interface recovers from it.
>
> Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
> in the case where we call ixgbevf_remove() after a failed recovery from
> AER error because the interrupts were not freed.
>
> Also moved the down and free functions into ixgbevf_close_suspend()
> same as with ixgbe.
>
> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
> Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> ---
>  drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 43 +++++++++++++----------
>  1 file changed, 25 insertions(+), 18 deletions(-)
>
> diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
> index 8574f21..7dfd1df 100644
> --- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
> +++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
> @@ -3228,6 +3228,21 @@ int ixgbevf_open(struct net_device *netdev)
>  }
>
>  /**
> + * ixgbevf_close_suspend - actions necessary to both suspend and close flows
> + * @adapter: the private adapter struct
> + *
> + * This function should contain the necessary work common to both suspending
> + * and closing of the device.
> + */
> +static void ixgbevf_close_suspend(struct ixgbevf_adapter *adapter)
> +{
> +		ixgbevf_down(adapter);
> +		ixgbevf_free_irq(adapter);
> +		ixgbevf_free_all_tx_resources(adapter);
> +		ixgbevf_free_all_rx_resources(adapter);

    Hum, why 2 tabs?

> +}
> +
> +/**
>   * ixgbevf_close - Disables a network interface
>   * @netdev: network interface device structure
>   *
[...]

MBR, Sergei

[net-next 13/21] ixgbe: Fix incorrect bitwise operations of PTP Rx timestamp flags

[Jeff Kirsher]

From: Yusuke Suzuki <yus-suzuki@uf.jp.nec.com>

Rx timestamp does not work on 82599 and X540 because bitwise operation
of RX_HWTSTAMP flags is incorrect and ixgbe_ptp_rx_hwtstamp() is never
called. This patch fixes it to enable Rx timestamp on 82599 and X540.

Without this fix:
ptp4l[278.730]: selected /dev/ptp8 as PTP clock
ptp4l[278.733]: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l[278.733]: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l[278.834]: port 1: received SYNC without timestamp
ptp4l[278.835]: port 1: new foreign master 1c3947.fffe.60f9cc-1
ptp4l[279.834]: port 1: received SYNC without timestamp
ptp4l[280.834]: port 1: received SYNC without timestamp
ptp4l[281.834]: port 1: received SYNC without timestamp
ptp4l[282.834]: port 1: received SYNC without timestamp
ptp4l[282.835]: selected best master clock 1c3947.fffe.60f9cc
ptp4l[282.835]: port 1: LISTENING to UNCALIBRATED on RS_SLAVE
ptp4l[283.834]: port 1: received SYNC without timestamp

With this fix:
ptp4l[239.154]: selected /dev/ptp8 as PTP clock
ptp4l[239.157]: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l[239.157]: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l[240.989]: port 1: new foreign master 1c3947.fffe.60f9cc-1
ptp4l[244.989]: selected best master clock 1c3947.fffe.60f9cc
ptp4l[244.989]: port 1: LISTENING to UNCALIBRATED on RS_SLAVE
ptp4l[246.977]: master offset -899583339542096 s0 freq      +0 path delay     16222
ptp4l[247.977]: master offset -899583339617265 s1 freq  -75169 path delay     16177
ptp4l[248.977]: master offset       -130 s2 freq  -75299 path delay     16177
ptp4l[248.977]: port 1: UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[249.977]: master offset         -9 s2 freq  -75217 path delay     16177
ptp4l[250.977]: master offset         88 s2 freq  -75123 path delay     16132

Fixes: a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x devices")
Signed-off-by: Yusuke Suzuki <yus-suzuki@uf.jp.nec.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c
index 1efb404..ef0635e 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c
@@ -858,14 +858,14 @@ static int ixgbe_ptp_set_timestamp_mode(struct ixgbe_adapter *adapter,
 	case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
 		tsync_rx_ctl |= IXGBE_TSYNCRXCTL_TYPE_L4_V1;
 		tsync_rx_mtrl |= IXGBE_RXMTRL_V1_SYNC_MSG;
-		adapter->flags &= ~(IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
-				    IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
+		adapter->flags |= (IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
+				   IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
 		break;
 	case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
 		tsync_rx_ctl |= IXGBE_TSYNCRXCTL_TYPE_L4_V1;
 		tsync_rx_mtrl |= IXGBE_RXMTRL_V1_DELAY_REQ_MSG;
-		adapter->flags &= ~(IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
-				    IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
+		adapter->flags |= (IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
+				   IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
 		break;
 	case HWTSTAMP_FILTER_PTP_V2_EVENT:
 	case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
@@ -879,8 +879,8 @@ static int ixgbe_ptp_set_timestamp_mode(struct ixgbe_adapter *adapter,
 		tsync_rx_ctl |= IXGBE_TSYNCRXCTL_TYPE_EVENT_V2;
 		is_l2 = true;
 		config->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
-		adapter->flags &= ~(IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
-				    IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
+		adapter->flags |= (IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
+				   IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
 		break;
 	case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
 	case HWTSTAMP_FILTER_ALL:
-- 
2.9.3

[net-next 14/21] ixgbevf: restore hw_addr on resume or error

[Jeff Kirsher]

From: Emil Tantilov <emil.s.tantilov@intel.com>

Restore adapter->hw.hw_addr after handling an error, or a resume
operation to make sure we can access the registers.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
index 7dfd1df..544307c 100644
--- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
+++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
@@ -3851,6 +3851,8 @@ static int ixgbevf_resume(struct pci_dev *pdev)
 		dev_err(&pdev->dev, "Cannot enable PCI device from suspend\n");
 		return err;
 	}
+
+	adapter->hw.hw_addr = adapter->io_addr;
 	smp_mb__before_atomic();
 	clear_bit(__IXGBEVF_DISABLED, &adapter->state);
 	pci_set_master(pdev);
@@ -4285,6 +4287,7 @@ static pci_ers_result_t ixgbevf_io_slot_reset(struct pci_dev *pdev)
 		return PCI_ERS_RESULT_DISCONNECT;
 	}
 
+	adapter->hw.hw_addr = adapter->io_addr;
 	smp_mb__before_atomic();
 	clear_bit(__IXGBEVF_DISABLED, &adapter->state);
 	pci_set_master(pdev);
-- 
2.9.3

[net-next 15/21] ixgbe: Configure advertised speeds correctly for KR/KX backplane

[Jeff Kirsher]

From: Don Skidmore <donald.c.skidmore@intel.com>

This patch ensures that the advertised link speeds are configured
for X553 KR/KX backplane.  Without this patch the link remains at
1G when resuming form low power after being downshifted by LPLU.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index 92f2b5e..675c198 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -2187,12 +2187,11 @@ static s32 ixgbe_setup_kx4_x550em(struct ixgbe_hw *hw)
 /**
  * ixgbe_setup_kr_x550em - Configure the KR PHY
  * @hw: pointer to hardware structure
- *
- * Configures the integrated KR PHY for X550EM_x.
  **/
 static s32 ixgbe_setup_kr_x550em(struct ixgbe_hw *hw)
 {
-	if (hw->mac.type != ixgbe_mac_X550EM_x)
+	/* leave linke alone for 2.5G */
+	if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_2_5GB_FULL)
 		return 0;
 
 	return ixgbe_setup_kr_speed_x550em(hw, hw->phy.autoneg_advertised);
-- 
2.9.3

Re: [net-next 15/21] ixgbe: Configure advertised speeds correctly for KR/KX backplane

[Sergei Shtylyov]

Hello.

On 12/30/2016 12:33 PM, Jeff Kirsher wrote:

> From: Don Skidmore <donald.c.skidmore@intel.com>
>
> This patch ensures that the advertised link speeds are configured
> for X553 KR/KX backplane.  Without this patch the link remains at
> 1G when resuming form low power after being downshifted by LPLU.
>
> Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> ---
>  drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 5 ++---
>  1 file changed, 2 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
> index 92f2b5e..675c198 100644
> --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
> +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
> @@ -2187,12 +2187,11 @@ static s32 ixgbe_setup_kx4_x550em(struct ixgbe_hw *hw)
>  /**
>   * ixgbe_setup_kr_x550em - Configure the KR PHY
>   * @hw: pointer to hardware structure
> - *
> - * Configures the integrated KR PHY for X550EM_x.
>   **/
>  static s32 ixgbe_setup_kr_x550em(struct ixgbe_hw *hw)
>  {
> -	if (hw->mac.type != ixgbe_mac_X550EM_x)
> +	/* leave linke alone for 2.5G */

    Link, maybe?

> +	if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_2_5GB_FULL)
>  		return 0;
>
>  	return ixgbe_setup_kr_speed_x550em(hw, hw->phy.autoneg_advertised);

MBR, Sergei

RE: [net-next 15/21] ixgbe: Configure advertised speeds correctly for KR/KX backplane

[Rosen, Rami]

Hi,

Hi,

On this occasion, also the next can be fixed:

> From: Don Skidmore <donald.c.skidmore@intel.com>
>
> This patch ensures that the advertised link speeds are configured for 
> X553 KR/KX backplane.  Without this patch the link remains at 1G when 
> resuming form low power after being downshifted by LPLU.

Should be "from" instead "from", I would assume.

Regards,
Rami Rosen
Intel Corporation

[net-next 16/21] ixgbe: Fix issues with EEPROM access

[Jeff Kirsher]

From: Mark Rustad <mark.d.rustad@intel.com>

There are two problems with EEPROM access. One is that it needs to
hold the semaphore until the entire response is read or else the
response can be corrupted by other firmware accesses. The second
problem is that acquiring and releasing the semaphore is slow, so
it should be taken and released once when multiple EEPROM accesses
will be done.

Both of these issues can be solved by adding a new function,
ixgbe_hic_unlocked, to issue firmware commands that will assume
that the caller has acquired the needed semaphore.

Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | 97 ++++++++++++++++---------
 drivers/net/ethernet/intel/ixgbe/ixgbe_common.h |  1 +
 drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c   | 75 +++++++------------
 3 files changed, 91 insertions(+), 82 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
index 5d8f1ae..851f485 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
@@ -3593,43 +3593,29 @@ u8 ixgbe_calculate_checksum(u8 *buffer, u32 length)
 }
 
 /**
- *  ixgbe_host_interface_command - Issue command to manageability block
+ *  ixgbe_hic_unlocked - Issue command to manageability block unlocked
  *  @hw: pointer to the HW structure
- *  @buffer: contains the command to write and where the return status will
- *           be placed
+ *  @buffer: command to write and where the return status will be placed
  *  @length: length of buffer, must be multiple of 4 bytes
  *  @timeout: time in ms to wait for command completion
- *  @return_data: read and return data from the buffer (true) or not (false)
- *  Needed because FW structures are big endian and decoding of
- *  these fields can be 8 bit or 16 bit based on command. Decoding
- *  is not easily understood without making a table of commands.
- *  So we will leave this up to the caller to read back the data
- *  in these cases.
  *
- *  Communicates with the manageability block.  On success return 0
- *  else return IXGBE_ERR_HOST_INTERFACE_COMMAND.
+ *  Communicates with the manageability block. On success return 0
+ *  else returns semaphore error when encountering an error acquiring
+ *  semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
+ *
+ *  This function assumes that the IXGBE_GSSR_SW_MNG_SM semaphore is held
+ *  by the caller.
  **/
-s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
-				 u32 length, u32 timeout,
-				 bool return_data)
+s32 ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 length,
+		       u32 timeout)
 {
-	u32 hdr_size = sizeof(struct ixgbe_hic_hdr);
-	u32 hicr, i, bi, fwsts;
-	u16 buf_len, dword_len;
-	union {
-		struct ixgbe_hic_hdr hdr;
-		u32 u32arr[1];
-	} *bp = buffer;
-	s32 status;
+	u32 hicr, i, fwsts;
+	u16 dword_len;
 
 	if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
 		hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
 		return IXGBE_ERR_HOST_INTERFACE_COMMAND;
 	}
-	/* Take management host interface semaphore */
-	status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
-	if (status)
-		return status;
 
 	/* Set bit 9 of FWSTS clearing FW reset indication */
 	fwsts = IXGBE_READ_REG(hw, IXGBE_FWSTS);
@@ -3639,15 +3625,13 @@ s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
 	hicr = IXGBE_READ_REG(hw, IXGBE_HICR);
 	if (!(hicr & IXGBE_HICR_EN)) {
 		hw_dbg(hw, "IXGBE_HOST_EN bit disabled.\n");
-		status = IXGBE_ERR_HOST_INTERFACE_COMMAND;
-		goto rel_out;
+		return IXGBE_ERR_HOST_INTERFACE_COMMAND;
 	}
 
 	/* Calculate length in DWORDs. We must be DWORD aligned */
 	if (length % sizeof(u32)) {
 		hw_dbg(hw, "Buffer length failure, not aligned to dword");
-		status = IXGBE_ERR_INVALID_ARGUMENT;
-		goto rel_out;
+		return IXGBE_ERR_INVALID_ARGUMENT;
 	}
 
 	dword_len = length >> 2;
@@ -3657,7 +3641,7 @@ s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
 	 */
 	for (i = 0; i < dword_len; i++)
 		IXGBE_WRITE_REG_ARRAY(hw, IXGBE_FLEX_MNG,
-				      i, cpu_to_le32(bp->u32arr[i]));
+				      i, cpu_to_le32(buffer[i]));
 
 	/* Setting this bit tells the ARC that a new command is pending. */
 	IXGBE_WRITE_REG(hw, IXGBE_HICR, hicr | IXGBE_HICR_C);
@@ -3671,11 +3655,54 @@ s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
 
 	/* Check command successful completion. */
 	if ((timeout && i == timeout) ||
-	    !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV)) {
-		hw_dbg(hw, "Command has failed with no status valid.\n");
-		status = IXGBE_ERR_HOST_INTERFACE_COMMAND;
-		goto rel_out;
+	    !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV))
+		return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+
+	return 0;
+}
+
+/**
+ *  ixgbe_host_interface_command - Issue command to manageability block
+ *  @hw: pointer to the HW structure
+ *  @buffer: contains the command to write and where the return status will
+ *           be placed
+ *  @length: length of buffer, must be multiple of 4 bytes
+ *  @timeout: time in ms to wait for command completion
+ *  @return_data: read and return data from the buffer (true) or not (false)
+ *  Needed because FW structures are big endian and decoding of
+ *  these fields can be 8 bit or 16 bit based on command. Decoding
+ *  is not easily understood without making a table of commands.
+ *  So we will leave this up to the caller to read back the data
+ *  in these cases.
+ *
+ *  Communicates with the manageability block.  On success return 0
+ *  else return IXGBE_ERR_HOST_INTERFACE_COMMAND.
+ **/
+s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
+				 u32 length, u32 timeout,
+				 bool return_data)
+{
+	u32 hdr_size = sizeof(struct ixgbe_hic_hdr);
+	union {
+		struct ixgbe_hic_hdr hdr;
+		u32 u32arr[1];
+	} *bp = buffer;
+	u16 buf_len, dword_len;
+	s32 status;
+	u32 bi;
+
+	if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
+		hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
+		return IXGBE_ERR_HOST_INTERFACE_COMMAND;
 	}
+	/* Take management host interface semaphore */
+	status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
+	if (status)
+		return status;
+
+	status = ixgbe_hic_unlocked(hw, buffer, length, timeout);
+	if (status)
+		goto rel_out;
 
 	if (!return_data)
 		goto rel_out;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
index 393aeab..671a0cd 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
@@ -115,6 +115,7 @@ s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
 u8 ixgbe_calculate_checksum(u8 *buffer, u32 length);
 s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *, u32 length,
 				 u32 timeout, bool return_data);
+s32 ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 len, u32 timeout);
 void ixgbe_clear_tx_pending(struct ixgbe_hw *hw);
 bool ixgbe_mng_present(struct ixgbe_hw *hw);
 bool ixgbe_mng_enabled(struct ixgbe_hw *hw);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index 675c198..d2fee52 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -624,41 +624,6 @@ static s32 ixgbe_read_iosf_sb_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr,
 	return status;
 }
 
-/** ixgbe_read_ee_hostif_data_X550 - Read EEPROM word using a host interface
- *  command assuming that the semaphore is already obtained.
- *  @hw: pointer to hardware structure
- *  @offset: offset of  word in the EEPROM to read
- *  @data: word read from the EEPROM
- *
- *  Reads a 16 bit word from the EEPROM using the hostif.
- **/
-static s32 ixgbe_read_ee_hostif_data_X550(struct ixgbe_hw *hw, u16 offset,
-					  u16 *data)
-{
-	s32 status;
-	struct ixgbe_hic_read_shadow_ram buffer;
-
-	buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD;
-	buffer.hdr.req.buf_lenh = 0;
-	buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN;
-	buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM;
-
-	/* convert offset from words to bytes */
-	buffer.address = cpu_to_be32(offset * 2);
-	/* one word */
-	buffer.length = cpu_to_be16(sizeof(u16));
-
-	status = ixgbe_host_interface_command(hw, &buffer, sizeof(buffer),
-					      IXGBE_HI_COMMAND_TIMEOUT, false);
-	if (status)
-		return status;
-
-	*data = (u16)IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG,
-					  FW_NVM_DATA_OFFSET);
-
-	return 0;
-}
-
 /** ixgbe_read_ee_hostif_buffer_X550- Read EEPROM word(s) using hostif
  *  @hw: pointer to hardware structure
  *  @offset: offset of  word in the EEPROM to read
@@ -670,6 +635,7 @@ static s32 ixgbe_read_ee_hostif_data_X550(struct ixgbe_hw *hw, u16 offset,
 static s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw,
 					    u16 offset, u16 words, u16 *data)
 {
+	const u32 mask = IXGBE_GSSR_SW_MNG_SM | IXGBE_GSSR_EEP_SM;
 	struct ixgbe_hic_read_shadow_ram buffer;
 	u32 current_word = 0;
 	u16 words_to_read;
@@ -677,7 +643,7 @@ static s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw,
 	u32 i;
 
 	/* Take semaphore for the entire operation. */
-	status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+	status = hw->mac.ops.acquire_swfw_sync(hw, mask);
 	if (status) {
 		hw_dbg(hw, "EEPROM read buffer - semaphore failed\n");
 		return status;
@@ -698,10 +664,8 @@ static s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw,
 		buffer.address = cpu_to_be32((offset + current_word) * 2);
 		buffer.length = cpu_to_be16(words_to_read * 2);
 
-		status = ixgbe_host_interface_command(hw, &buffer,
-						      sizeof(buffer),
-						      IXGBE_HI_COMMAND_TIMEOUT,
-						      false);
+		status = ixgbe_hic_unlocked(hw, (u32 *)&buffer, sizeof(buffer),
+					    IXGBE_HI_COMMAND_TIMEOUT);
 		if (status) {
 			hw_dbg(hw, "Host interface command failed\n");
 			goto out;
@@ -725,7 +689,7 @@ static s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw,
 	}
 
 out:
-	hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+	hw->mac.ops.release_swfw_sync(hw, mask);
 	return status;
 }
 
@@ -896,15 +860,32 @@ static s32 ixgbe_calc_eeprom_checksum_X550(struct ixgbe_hw *hw)
  **/
 static s32 ixgbe_read_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset, u16 *data)
 {
-	s32 status = 0;
+	const u32 mask = IXGBE_GSSR_SW_MNG_SM | IXGBE_GSSR_EEP_SM;
+	struct ixgbe_hic_read_shadow_ram buffer;
+	s32 status;
 
-	if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) == 0) {
-		status = ixgbe_read_ee_hostif_data_X550(hw, offset, data);
-		hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
-	} else {
-		status = IXGBE_ERR_SWFW_SYNC;
+	buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD;
+	buffer.hdr.req.buf_lenh = 0;
+	buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN;
+	buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM;
+
+	/* convert offset from words to bytes */
+	buffer.address = cpu_to_be32(offset * 2);
+	/* one word */
+	buffer.length = cpu_to_be16(sizeof(u16));
+
+	status = hw->mac.ops.acquire_swfw_sync(hw, mask);
+	if (status)
+		return status;
+
+	status = ixgbe_hic_unlocked(hw, (u32 *)&buffer, sizeof(buffer),
+				    IXGBE_HI_COMMAND_TIMEOUT);
+	if (!status) {
+		*data = (u16)IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG,
+						  FW_NVM_DATA_OFFSET);
 	}
 
+	hw->mac.ops.release_swfw_sync(hw, mask);
 	return status;
 }
 
-- 
2.9.3

[net-next 17/21] ixgbe: Remove unused firmware version functions and method

[Jeff Kirsher]

From: Mark Rustad <mark.d.rustad@intel.com>

The firmware version method and functions are not used anywhere, so
remove them all.

Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c |  2 --
 drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c |  2 --
 drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c   | 34 --------------------------
 drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h   |  4 ---
 drivers/net/ethernet/intel/ixgbe/ixgbe_type.h  |  1 -
 drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c  |  1 -
 drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c  |  3 +--
 7 files changed, 1 insertion(+), 46 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c
index 805ab31..523f9d0 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c
@@ -139,8 +139,6 @@ static s32 ixgbe_init_phy_ops_82598(struct ixgbe_hw *hw)
 	case ixgbe_phy_tn:
 		phy->ops.setup_link = &ixgbe_setup_phy_link_tnx;
 		phy->ops.check_link = &ixgbe_check_phy_link_tnx;
-		phy->ops.get_firmware_version =
-			     &ixgbe_get_phy_firmware_version_tnx;
 		break;
 	case ixgbe_phy_nl:
 		phy->ops.reset = &ixgbe_reset_phy_nl;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
index e00aaeb..30535e6 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
@@ -331,8 +331,6 @@ static s32 ixgbe_init_phy_ops_82599(struct ixgbe_hw *hw)
 	case ixgbe_phy_tn:
 		phy->ops.check_link = &ixgbe_check_phy_link_tnx;
 		phy->ops.setup_link = &ixgbe_setup_phy_link_tnx;
-		phy->ops.get_firmware_version =
-			     &ixgbe_get_phy_firmware_version_tnx;
 		break;
 	default:
 		break;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
index 019b3c2..67a399b 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
@@ -977,40 +977,6 @@ s32 ixgbe_setup_phy_link_tnx(struct ixgbe_hw *hw)
 }
 
 /**
- *  ixgbe_get_phy_firmware_version_tnx - Gets the PHY Firmware Version
- *  @hw: pointer to hardware structure
- *  @firmware_version: pointer to the PHY Firmware Version
- **/
-s32 ixgbe_get_phy_firmware_version_tnx(struct ixgbe_hw *hw,
-				       u16 *firmware_version)
-{
-	s32 status;
-
-	status = hw->phy.ops.read_reg(hw, TNX_FW_REV,
-				      MDIO_MMD_VEND1,
-				      firmware_version);
-
-	return status;
-}
-
-/**
- *  ixgbe_get_phy_firmware_version_generic - Gets the PHY Firmware Version
- *  @hw: pointer to hardware structure
- *  @firmware_version: pointer to the PHY Firmware Version
- **/
-s32 ixgbe_get_phy_firmware_version_generic(struct ixgbe_hw *hw,
-					   u16 *firmware_version)
-{
-	s32 status;
-
-	status = hw->phy.ops.read_reg(hw, AQ_FW_REV,
-				      MDIO_MMD_VEND1,
-				      firmware_version);
-
-	return status;
-}
-
-/**
  *  ixgbe_reset_phy_nl - Performs a PHY reset
  *  @hw: pointer to hardware structure
  **/
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
index ecf05f8..5aa2c3c 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
@@ -168,10 +168,6 @@ s32 ixgbe_check_phy_link_tnx(struct ixgbe_hw *hw,
 			     ixgbe_link_speed *speed,
 			     bool *link_up);
 s32 ixgbe_setup_phy_link_tnx(struct ixgbe_hw *hw);
-s32 ixgbe_get_phy_firmware_version_tnx(struct ixgbe_hw *hw,
-				       u16 *firmware_version);
-s32 ixgbe_get_phy_firmware_version_generic(struct ixgbe_hw *hw,
-					   u16 *firmware_version);
 
 s32 ixgbe_reset_phy_nl(struct ixgbe_hw *hw);
 s32 ixgbe_set_copper_phy_power(struct ixgbe_hw *hw, bool on);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
index 0d85511..5c59b3c 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
@@ -3404,7 +3404,6 @@ struct ixgbe_phy_operations {
 	s32 (*setup_internal_link)(struct ixgbe_hw *);
 	s32 (*setup_link_speed)(struct ixgbe_hw *, ixgbe_link_speed, bool);
 	s32 (*check_link)(struct ixgbe_hw *, ixgbe_link_speed *, bool *);
-	s32 (*get_firmware_version)(struct ixgbe_hw *, u16 *);
 	s32 (*read_i2c_byte)(struct ixgbe_hw *, u8, u8, u8 *);
 	s32 (*write_i2c_byte)(struct ixgbe_hw *, u8, u8, u8);
 	s32 (*read_i2c_sff8472)(struct ixgbe_hw *, u8 , u8 *);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
index afc4d16..84a467a 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
@@ -918,7 +918,6 @@ static const struct ixgbe_phy_operations phy_ops_X540 = {
 	.write_i2c_eeprom       = &ixgbe_write_i2c_eeprom_generic,
 	.check_overtemp         = &ixgbe_tn_check_overtemp,
 	.set_phy_power          = &ixgbe_set_copper_phy_power,
-	.get_firmware_version   = &ixgbe_get_phy_firmware_version_generic,
 };
 
 static const u32 ixgbe_mvals_X540[IXGBE_MVALS_IDX_LIMIT] = {
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index d2fee52..3c3bf48 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -3419,8 +3419,7 @@ static const struct ixgbe_eeprom_operations eeprom_ops_X550EM_x = {
 	.write_i2c_eeprom	= &ixgbe_write_i2c_eeprom_generic, \
 	.setup_link		= &ixgbe_setup_phy_link_generic, \
 	.set_phy_power		= NULL, \
-	.check_overtemp		= &ixgbe_tn_check_overtemp, \
-	.get_firmware_version	= &ixgbe_get_phy_firmware_version_generic,
+	.check_overtemp		= &ixgbe_tn_check_overtemp,
 
 static const struct ixgbe_phy_operations phy_ops_X550 = {
 	X550_COMMON_PHY
-- 
2.9.3

[net-next 18/21] ixgbe: Implement firmware interface to access some PHYs

[Jeff Kirsher]

From: Mark Rustad <mark.d.rustad@intel.com>

Implement new interface for firmware commands to access some PHYs.

Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_common.h |  2 +
 drivers/net/ethernet/intel/ixgbe/ixgbe_type.h   | 66 +++++++++++++++++++++++++
 drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c   | 45 +++++++++++++++++
 3 files changed, 113 insertions(+)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
index 671a0cd..e083732 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
@@ -116,6 +116,8 @@ u8 ixgbe_calculate_checksum(u8 *buffer, u32 length);
 s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *, u32 length,
 				 u32 timeout, bool return_data);
 s32 ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 len, u32 timeout);
+s32 ixgbe_fw_phy_activity(struct ixgbe_hw *hw, u16 activity,
+			  u32 (*data)[FW_PHY_ACT_DATA_COUNT]);
 void ixgbe_clear_tx_pending(struct ixgbe_hw *hw);
 bool ixgbe_mng_present(struct ixgbe_hw *hw);
 bool ixgbe_mng_enabled(struct ixgbe_hw *hw);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
index 5c59b3c..a8f2d70 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
@@ -2645,6 +2645,59 @@ enum ixgbe_fdir_pballoc_type {
 #define FW_INT_PHY_REQ_LEN		10
 #define FW_INT_PHY_REQ_READ		0
 #define FW_INT_PHY_REQ_WRITE		1
+#define FW_PHY_ACT_REQ_CMD		5
+#define FW_PHY_ACT_DATA_COUNT		4
+#define FW_PHY_ACT_REQ_LEN		(4 + 4 * FW_PHY_ACT_DATA_COUNT)
+#define FW_PHY_ACT_INIT_PHY		1
+#define FW_PHY_ACT_SETUP_LINK		2
+#define FW_PHY_ACT_LINK_SPEED_10	BIT(0)
+#define FW_PHY_ACT_LINK_SPEED_100	BIT(1)
+#define FW_PHY_ACT_LINK_SPEED_1G	BIT(2)
+#define FW_PHY_ACT_LINK_SPEED_2_5G	BIT(3)
+#define FW_PHY_ACT_LINK_SPEED_5G	BIT(4)
+#define FW_PHY_ACT_LINK_SPEED_10G	BIT(5)
+#define FW_PHY_ACT_LINK_SPEED_20G	BIT(6)
+#define FW_PHY_ACT_LINK_SPEED_25G	BIT(7)
+#define FW_PHY_ACT_LINK_SPEED_40G	BIT(8)
+#define FW_PHY_ACT_LINK_SPEED_50G	BIT(9)
+#define FW_PHY_ACT_LINK_SPEED_100G	BIT(10)
+#define FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT 16
+#define FW_PHY_ACT_SETUP_LINK_PAUSE_MASK (3 << \
+					  HW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT)
+#define FW_PHY_ACT_SETUP_LINK_PAUSE_NONE 0u
+#define FW_PHY_ACT_SETUP_LINK_PAUSE_TX	1u
+#define FW_PHY_ACT_SETUP_LINK_PAUSE_RX	2u
+#define FW_PHY_ACT_SETUP_LINK_PAUSE_RXTX 3u
+#define FW_PHY_ACT_SETUP_LINK_LP	BIT(18)
+#define FW_PHY_ACT_SETUP_LINK_HP	BIT(19)
+#define FW_PHY_ACT_SETUP_LINK_EEE	BIT(20)
+#define FW_PHY_ACT_SETUP_LINK_AN	BIT(22)
+#define FW_PHY_ACT_SETUP_LINK_RSP_DOWN	BIT(0)
+#define FW_PHY_ACT_GET_LINK_INFO	3
+#define FW_PHY_ACT_GET_LINK_INFO_EEE	BIT(19)
+#define FW_PHY_ACT_GET_LINK_INFO_FC_TX	BIT(20)
+#define FW_PHY_ACT_GET_LINK_INFO_FC_RX	BIT(21)
+#define FW_PHY_ACT_GET_LINK_INFO_POWER	BIT(22)
+#define FW_PHY_ACT_GET_LINK_INFO_AN_COMPLETE	BIT(24)
+#define FW_PHY_ACT_GET_LINK_INFO_TEMP	BIT(25)
+#define FW_PHY_ACT_GET_LINK_INFO_LP_FC_TX	BIT(28)
+#define FW_PHY_ACT_GET_LINK_INFO_LP_FC_RX	BIT(29)
+#define FW_PHY_ACT_FORCE_LINK_DOWN	4
+#define FW_PHY_ACT_FORCE_LINK_DOWN_OFF	BIT(0)
+#define FW_PHY_ACT_PHY_SW_RESET		5
+#define FW_PHY_ACT_PHY_HW_RESET		6
+#define FW_PHY_ACT_GET_PHY_INFO		7
+#define FW_PHY_ACT_UD_2			0x1002
+#define FW_PHY_ACT_UD_2_10G_KR_EEE	BIT(6)
+#define FW_PHY_ACT_UD_2_10G_KX4_EEE	BIT(5)
+#define FW_PHY_ACT_UD_2_1G_KX_EEE	BIT(4)
+#define FW_PHY_ACT_UD_2_10G_T_EEE	BIT(3)
+#define FW_PHY_ACT_UD_2_1G_T_EEE	BIT(2)
+#define FW_PHY_ACT_UD_2_100M_TX_EEE	BIT(1)
+#define FW_PHY_ACT_RETRIES		50
+#define FW_PHY_INFO_SPEED_MASK		0xFFFu
+#define FW_PHY_INFO_ID_HI_MASK		0xFFFF0000u
+#define FW_PHY_INFO_ID_LO_MASK		0x0000FFFFu
 
 /* Host Interface Command Structures */
 struct ixgbe_hic_hdr {
@@ -2745,6 +2798,19 @@ struct ixgbe_hic_internal_phy_resp {
 	__be32 read_data;
 };
 
+struct ixgbe_hic_phy_activity_req {
+	struct ixgbe_hic_hdr hdr;
+	u8 port_number;
+	u8 pad;
+	__le16 activity_id;
+	__be32 data[FW_PHY_ACT_DATA_COUNT];
+};
+
+struct ixgbe_hic_phy_activity_resp {
+	struct ixgbe_hic_hdr hdr;
+	__be32 data[FW_PHY_ACT_DATA_COUNT];
+};
+
 /* Transmit Descriptor - Advanced */
 union ixgbe_adv_tx_desc {
 	struct {
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index 3c3bf48..b9277df 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -402,6 +402,51 @@ ixgbe_write_i2c_combined_generic_unlocked(struct ixgbe_hw *hw,
 	return ixgbe_write_i2c_combined_generic_int(hw, addr, reg, val, false);
 }
 
+/**
+ * ixgbe_fw_phy_activity - Perform an activity on a PHY
+ * @hw: pointer to hardware structure
+ * @activity: activity to perform
+ * @data: Pointer to 4 32-bit words of data
+ */
+s32 ixgbe_fw_phy_activity(struct ixgbe_hw *hw, u16 activity,
+			  u32 (*data)[FW_PHY_ACT_DATA_COUNT])
+{
+	union {
+		struct ixgbe_hic_phy_activity_req cmd;
+		struct ixgbe_hic_phy_activity_resp rsp;
+	} hic;
+	u16 retries = FW_PHY_ACT_RETRIES;
+	s32 rc;
+	u32 i;
+
+	do {
+		memset(&hic, 0, sizeof(hic));
+		hic.cmd.hdr.cmd = FW_PHY_ACT_REQ_CMD;
+		hic.cmd.hdr.buf_len = FW_PHY_ACT_REQ_LEN;
+		hic.cmd.hdr.checksum = FW_DEFAULT_CHECKSUM;
+		hic.cmd.port_number = hw->bus.lan_id;
+		hic.cmd.activity_id = cpu_to_le16(activity);
+		for (i = 0; i < ARRAY_SIZE(hic.cmd.data); ++i)
+			hic.cmd.data[i] = cpu_to_be32((*data)[i]);
+
+		rc = ixgbe_host_interface_command(hw, &hic.cmd, sizeof(hic.cmd),
+						  IXGBE_HI_COMMAND_TIMEOUT,
+						  true);
+		if (rc)
+			return rc;
+		if (hic.rsp.hdr.cmd_or_resp.ret_status ==
+		    FW_CEM_RESP_STATUS_SUCCESS) {
+			for (i = 0; i < FW_PHY_ACT_DATA_COUNT; ++i)
+				(*data)[i] = be32_to_cpu(hic.rsp.data[i]);
+			return 0;
+		}
+		usleep_range(20, 30);
+		--retries;
+	} while (retries > 0);
+
+	return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+}
+
 /** ixgbe_init_eeprom_params_X550 - Initialize EEPROM params
  *  @hw: pointer to hardware structure
  *
-- 
2.9.3

[net-next 19/21] ixgbe: Implement support for firmware-controlled PHYs

[Jeff Kirsher]

From: Mark Rustad <mark.d.rustad@intel.com>

Implement support for devices that have firmware-controlled PHYs.

Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe.h         |   4 +
 drivers/net/ethernet/intel/ixgbe/ixgbe_common.c  |   9 +
 drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c | 153 ++++++++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_main.c    |  64 ++++
 drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c     |   3 +
 drivers/net/ethernet/intel/ixgbe/ixgbe_type.h    |   7 +
 drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c    | 408 ++++++++++++++++++++++-
 7 files changed, 642 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe.h b/drivers/net/ethernet/intel/ixgbe/ixgbe.h
index ef81c3d..53fb427 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe.h
@@ -661,6 +661,8 @@ struct ixgbe_adapter {
 #define IXGBE_FLAG2_PHY_INTERRUPT		BIT(11)
 #define IXGBE_FLAG2_UDP_TUN_REREG_NEEDED	BIT(12)
 #define IXGBE_FLAG2_VLAN_PROMISC		BIT(13)
+#define IXGBE_FLAG2_EEE_CAPABLE			BIT(14)
+#define IXGBE_FLAG2_EEE_ENABLED			BIT(15)
 
 	/* Tx fast path data */
 	int num_tx_queues;
@@ -862,6 +864,7 @@ enum ixgbe_boards {
 	board_X550,
 	board_X550EM_x,
 	board_x550em_a,
+	board_x550em_a_fw,
 };
 
 extern const struct ixgbe_info ixgbe_82598_info;
@@ -870,6 +873,7 @@ extern const struct ixgbe_info ixgbe_X540_info;
 extern const struct ixgbe_info ixgbe_X550_info;
 extern const struct ixgbe_info ixgbe_X550EM_x_info;
 extern const struct ixgbe_info ixgbe_x550em_a_info;
+extern const struct ixgbe_info ixgbe_x550em_a_fw_info;
 #ifdef CONFIG_IXGBE_DCB
 extern const struct dcbnl_rtnl_ops dcbnl_ops;
 #endif
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
index 851f485..094e1d6 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
@@ -100,6 +100,8 @@ bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
 		case IXGBE_DEV_ID_X550T1:
 		case IXGBE_DEV_ID_X550EM_X_10G_T:
 		case IXGBE_DEV_ID_X550EM_A_10G_T:
+		case IXGBE_DEV_ID_X550EM_A_1G_T:
+		case IXGBE_DEV_ID_X550EM_A_1G_T_L:
 			supported = true;
 			break;
 		default:
@@ -3382,6 +3384,13 @@ s32 ixgbe_check_mac_link_generic(struct ixgbe_hw *hw, ixgbe_link_speed *speed,
 		else
 			*speed = IXGBE_LINK_SPEED_100_FULL;
 		break;
+	case IXGBE_LINKS_SPEED_10_X550EM_A:
+		*speed = IXGBE_LINK_SPEED_UNKNOWN;
+		if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
+		    hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L) {
+			*speed = IXGBE_LINK_SPEED_10_FULL;
+		}
+		break;
 	default:
 		*speed = IXGBE_LINK_SPEED_UNKNOWN;
 	}
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
index 8789f21..1758906 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
@@ -197,15 +197,17 @@ static int ixgbe_get_settings(struct net_device *netdev,
 				   SUPPORTED_1000baseKX_Full :
 				   SUPPORTED_1000baseT_Full;
 	if (supported_link & IXGBE_LINK_SPEED_100_FULL)
-		ecmd->supported |= ixgbe_isbackplane(hw->phy.media_type) ?
-				   SUPPORTED_1000baseKX_Full :
-				   SUPPORTED_100baseT_Full;
+		ecmd->supported |= SUPPORTED_100baseT_Full;
+	if (supported_link & IXGBE_LINK_SPEED_10_FULL)
+		ecmd->supported |= SUPPORTED_10baseT_Full;
 
 	/* default advertised speed if phy.autoneg_advertised isn't set */
 	ecmd->advertising = ecmd->supported;
 	/* set the advertised speeds */
 	if (hw->phy.autoneg_advertised) {
 		ecmd->advertising = 0;
+		if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10_FULL)
+			ecmd->advertising |= ADVERTISED_10baseT_Full;
 		if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_100_FULL)
 			ecmd->advertising |= ADVERTISED_100baseT_Full;
 		if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10GB_FULL)
@@ -237,6 +239,7 @@ static int ixgbe_get_settings(struct net_device *netdev,
 	case ixgbe_phy_tn:
 	case ixgbe_phy_aq:
 	case ixgbe_phy_x550em_ext_t:
+	case ixgbe_phy_fw:
 	case ixgbe_phy_cu_unknown:
 		ecmd->supported |= SUPPORTED_TP;
 		ecmd->advertising |= ADVERTISED_TP;
@@ -346,6 +349,9 @@ static int ixgbe_get_settings(struct net_device *netdev,
 		case IXGBE_LINK_SPEED_100_FULL:
 			ethtool_cmd_speed_set(ecmd, SPEED_100);
 			break;
+		case IXGBE_LINK_SPEED_10_FULL:
+			ethtool_cmd_speed_set(ecmd, SPEED_10);
+			break;
 		default:
 			break;
 		}
@@ -394,6 +400,9 @@ static int ixgbe_set_settings(struct net_device *netdev,
 		if (ecmd->advertising & ADVERTISED_100baseT_Full)
 			advertised |= IXGBE_LINK_SPEED_100_FULL;
 
+		if (ecmd->advertising & ADVERTISED_10baseT_Full)
+			advertised |= IXGBE_LINK_SPEED_10_FULL;
+
 		if (old == advertised)
 			return err;
 		/* this sets the link speed and restarts auto-neg */
@@ -3173,6 +3182,9 @@ static int ixgbe_get_module_info(struct net_device *dev,
 	u8 sff8472_rev, addr_mode;
 	bool page_swap = false;
 
+	if (hw->phy.type == ixgbe_phy_fw)
+		return -ENXIO;
+
 	/* Check whether we support SFF-8472 or not */
 	status = hw->phy.ops.read_i2c_eeprom(hw,
 					     IXGBE_SFF_SFF_8472_COMP,
@@ -3218,6 +3230,9 @@ static int ixgbe_get_module_eeprom(struct net_device *dev,
 	if (ee->len == 0)
 		return -EINVAL;
 
+	if (hw->phy.type == ixgbe_phy_fw)
+		return -ENXIO;
+
 	for (i = ee->offset; i < ee->offset + ee->len; i++) {
 		/* I2C reads can take long time */
 		if (test_bit(__IXGBE_IN_SFP_INIT, &adapter->state))
@@ -3237,6 +3252,136 @@ static int ixgbe_get_module_eeprom(struct net_device *dev,
 	return 0;
 }
 
+static const struct {
+	ixgbe_link_speed mac_speed;
+	u32 supported;
+} ixgbe_ls_map[] = {
+	{ IXGBE_LINK_SPEED_10_FULL, SUPPORTED_10baseT_Full },
+	{ IXGBE_LINK_SPEED_100_FULL, SUPPORTED_100baseT_Full },
+	{ IXGBE_LINK_SPEED_1GB_FULL, SUPPORTED_1000baseT_Full },
+	{ IXGBE_LINK_SPEED_2_5GB_FULL, SUPPORTED_2500baseX_Full },
+	{ IXGBE_LINK_SPEED_10GB_FULL, SUPPORTED_10000baseT_Full },
+};
+
+static const struct {
+	u32 lp_advertised;
+	u32 mac_speed;
+} ixgbe_lp_map[] = {
+	{ FW_PHY_ACT_UD_2_100M_TX_EEE, SUPPORTED_100baseT_Full },
+	{ FW_PHY_ACT_UD_2_1G_T_EEE, SUPPORTED_1000baseT_Full },
+	{ FW_PHY_ACT_UD_2_10G_T_EEE, SUPPORTED_10000baseT_Full },
+	{ FW_PHY_ACT_UD_2_1G_KX_EEE, SUPPORTED_1000baseKX_Full },
+	{ FW_PHY_ACT_UD_2_10G_KX4_EEE, SUPPORTED_10000baseKX4_Full },
+	{ FW_PHY_ACT_UD_2_10G_KR_EEE, SUPPORTED_10000baseKR_Full},
+};
+
+static int
+ixgbe_get_eee_fw(struct ixgbe_adapter *adapter, struct ethtool_eee *edata)
+{
+	u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 };
+	struct ixgbe_hw *hw = &adapter->hw;
+	s32 rc;
+	u16 i;
+
+	rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_UD_2, &info);
+	if (rc)
+		return rc;
+
+	edata->lp_advertised = 0;
+	for (i = 0; i < ARRAY_SIZE(ixgbe_lp_map); ++i) {
+		if (info[0] & ixgbe_lp_map[i].lp_advertised)
+			edata->lp_advertised |= ixgbe_lp_map[i].mac_speed;
+	}
+
+	edata->supported = 0;
+	for (i = 0; i < ARRAY_SIZE(ixgbe_ls_map); ++i) {
+		if (hw->phy.eee_speeds_supported & ixgbe_ls_map[i].mac_speed)
+			edata->supported |= ixgbe_ls_map[i].supported;
+	}
+
+	edata->advertised = 0;
+	for (i = 0; i < ARRAY_SIZE(ixgbe_ls_map); ++i) {
+		if (hw->phy.eee_speeds_advertised & ixgbe_ls_map[i].mac_speed)
+			edata->advertised |= ixgbe_ls_map[i].supported;
+	}
+
+	edata->eee_enabled = !!edata->advertised;
+	edata->tx_lpi_enabled = edata->eee_enabled;
+	if (edata->advertised & edata->lp_advertised)
+		edata->eee_active = true;
+
+	return 0;
+}
+
+static int ixgbe_get_eee(struct net_device *netdev, struct ethtool_eee *edata)
+{
+	struct ixgbe_adapter *adapter = netdev_priv(netdev);
+	struct ixgbe_hw *hw = &adapter->hw;
+
+	if (!(adapter->flags2 & IXGBE_FLAG2_EEE_CAPABLE))
+		return -EOPNOTSUPP;
+
+	if (hw->phy.eee_speeds_supported && hw->phy.type == ixgbe_phy_fw)
+		return ixgbe_get_eee_fw(adapter, edata);
+
+	return -EOPNOTSUPP;
+}
+
+static int ixgbe_set_eee(struct net_device *netdev, struct ethtool_eee *edata)
+{
+	struct ixgbe_adapter *adapter = netdev_priv(netdev);
+	struct ixgbe_hw *hw = &adapter->hw;
+	struct ethtool_eee eee_data;
+	s32 ret_val;
+
+	if (!(adapter->flags2 & IXGBE_FLAG2_EEE_CAPABLE))
+		return -EOPNOTSUPP;
+
+	memset(&eee_data, 0, sizeof(struct ethtool_eee));
+
+	ret_val = ixgbe_get_eee(netdev, &eee_data);
+	if (ret_val)
+		return ret_val;
+
+	if (eee_data.eee_enabled && !edata->eee_enabled) {
+		if (eee_data.tx_lpi_enabled != edata->tx_lpi_enabled) {
+			e_err(drv, "Setting EEE tx-lpi is not supported\n");
+			return -EINVAL;
+		}
+
+		if (eee_data.tx_lpi_timer != edata->tx_lpi_timer) {
+			e_err(drv,
+			      "Setting EEE Tx LPI timer is not supported\n");
+			return -EINVAL;
+		}
+
+		if (eee_data.advertised != edata->advertised) {
+			e_err(drv,
+			      "Setting EEE advertised speeds is not supported\n");
+			return -EINVAL;
+		}
+	}
+
+	if (eee_data.eee_enabled != edata->eee_enabled) {
+		if (edata->eee_enabled) {
+			adapter->flags2 |= IXGBE_FLAG2_EEE_ENABLED;
+			hw->phy.eee_speeds_advertised =
+						   hw->phy.eee_speeds_supported;
+		} else {
+			adapter->flags2 &= ~IXGBE_FLAG2_EEE_ENABLED;
+			hw->phy.eee_speeds_advertised = 0;
+		}
+
+		/* reset link */
+		if (netif_running(netdev))
+			ixgbe_reinit_locked(adapter);
+		else
+			ixgbe_reset(adapter);
+	}
+
+	return 0;
+}
+
 static const struct ethtool_ops ixgbe_ethtool_ops = {
 	.get_settings           = ixgbe_get_settings,
 	.set_settings           = ixgbe_set_settings,
@@ -3269,6 +3414,8 @@ static const struct ethtool_ops ixgbe_ethtool_ops = {
 	.get_rxfh_key_size	= ixgbe_get_rxfh_key_size,
 	.get_rxfh		= ixgbe_get_rxfh,
 	.set_rxfh		= ixgbe_set_rxfh,
+	.get_eee		= ixgbe_get_eee,
+	.set_eee		= ixgbe_set_eee,
 	.get_channels		= ixgbe_get_channels,
 	.set_channels		= ixgbe_set_channels,
 	.get_ts_info		= ixgbe_get_ts_info,
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
index 9ca167c..0c6eca5 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -86,6 +86,7 @@ static const struct ixgbe_info *ixgbe_info_tbl[] = {
 	[board_X550]		= &ixgbe_X550_info,
 	[board_X550EM_x]	= &ixgbe_X550EM_x_info,
 	[board_x550em_a]	= &ixgbe_x550em_a_info,
+	[board_x550em_a_fw]	= &ixgbe_x550em_a_fw_info,
 };
 
 /* ixgbe_pci_tbl - PCI Device ID Table
@@ -140,6 +141,8 @@ static const struct pci_device_id ixgbe_pci_tbl[] = {
 	{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_A_SGMII_L), board_x550em_a },
 	{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_A_10G_T), board_x550em_a},
 	{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_A_SFP), board_x550em_a },
+	{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_A_1G_T), board_x550em_a_fw },
+	{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_A_1G_T_L), board_x550em_a_fw },
 	/* required last entry */
 	{0, }
 };
@@ -180,6 +183,7 @@ MODULE_VERSION(DRV_VERSION);
 static struct workqueue_struct *ixgbe_wq;
 
 static bool ixgbe_check_cfg_remove(struct ixgbe_hw *hw, struct pci_dev *pdev);
+static void ixgbe_watchdog_link_is_down(struct ixgbe_adapter *);
 
 static int ixgbe_read_pci_cfg_word_parent(struct ixgbe_adapter *adapter,
 					  u32 reg, u16 *value)
@@ -2447,6 +2451,7 @@ static void ixgbe_check_overtemp_subtask(struct ixgbe_adapter *adapter)
 {
 	struct ixgbe_hw *hw = &adapter->hw;
 	u32 eicr = adapter->interrupt_event;
+	s32 rc;
 
 	if (test_bit(__IXGBE_DOWN, &adapter->state))
 		return;
@@ -2485,6 +2490,12 @@ static void ixgbe_check_overtemp_subtask(struct ixgbe_adapter *adapter)
 			return;
 
 		break;
+	case IXGBE_DEV_ID_X550EM_A_1G_T:
+	case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+		rc = hw->phy.ops.check_overtemp(hw);
+		if (rc != IXGBE_ERR_OVERTEMP)
+			return;
+		break;
 	default:
 		if (adapter->hw.mac.type >= ixgbe_mac_X540)
 			return;
@@ -2531,6 +2542,18 @@ static void ixgbe_check_overtemp_event(struct ixgbe_adapter *adapter, u32 eicr)
 			return;
 		}
 		return;
+	case ixgbe_mac_x550em_a:
+		if (eicr & IXGBE_EICR_GPI_SDP0_X550EM_a) {
+			adapter->interrupt_event = eicr;
+			adapter->flags2 |= IXGBE_FLAG2_TEMP_SENSOR_EVENT;
+			ixgbe_service_event_schedule(adapter);
+			IXGBE_WRITE_REG(&adapter->hw, IXGBE_EIMC,
+					IXGBE_EICR_GPI_SDP0_X550EM_a);
+			IXGBE_WRITE_REG(&adapter->hw, IXGBE_EICR,
+					IXGBE_EICR_GPI_SDP0_X550EM_a);
+		}
+		return;
+	case ixgbe_mac_X550:
 	case ixgbe_mac_X540:
 		if (!(eicr & IXGBE_EICR_TS))
 			return;
@@ -5294,6 +5317,8 @@ void ixgbe_reinit_locked(struct ixgbe_adapter *adapter)
 
 	while (test_and_set_bit(__IXGBE_RESETTING, &adapter->state))
 		usleep_range(1000, 2000);
+	if (adapter->hw.phy.type == ixgbe_phy_fw)
+		ixgbe_watchdog_link_is_down(adapter);
 	ixgbe_down(adapter);
 	/*
 	 * If SR-IOV enabled then wait a bit before bringing the adapter
@@ -5554,6 +5579,31 @@ void ixgbe_down(struct ixgbe_adapter *adapter)
 }
 
 /**
+ * ixgbe_eee_capable - helper function to determine EEE support on X550
+ * @adapter: board private structure
+ */
+static void ixgbe_set_eee_capable(struct ixgbe_adapter *adapter)
+{
+	struct ixgbe_hw *hw = &adapter->hw;
+
+	switch (hw->device_id) {
+	case IXGBE_DEV_ID_X550EM_A_1G_T:
+	case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+		if (!hw->phy.eee_speeds_supported)
+			break;
+		adapter->flags2 |= IXGBE_FLAG2_EEE_CAPABLE;
+		if (!hw->phy.eee_speeds_advertised)
+			break;
+		adapter->flags2 |= IXGBE_FLAG2_EEE_ENABLED;
+		break;
+	default:
+		adapter->flags2 &= ~IXGBE_FLAG2_EEE_CAPABLE;
+		adapter->flags2 &= ~IXGBE_FLAG2_EEE_ENABLED;
+		break;
+	}
+}
+
+/**
  * ixgbe_tx_timeout - Respond to a Tx Hang
  * @netdev: network interface device structure
  **/
@@ -5717,6 +5767,14 @@ static int ixgbe_sw_init(struct ixgbe_adapter *adapter,
 		break;
 	case ixgbe_mac_x550em_a:
 		adapter->flags |= IXGBE_FLAG_GENEVE_OFFLOAD_CAPABLE;
+		switch (hw->device_id) {
+		case IXGBE_DEV_ID_X550EM_A_1G_T:
+		case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+			adapter->flags2 |= IXGBE_FLAG2_TEMP_SENSOR_CAPABLE;
+			break;
+		default:
+			break;
+		}
 	/* fall through */
 	case ixgbe_mac_X550EM_x:
 #ifdef CONFIG_IXGBE_DCB
@@ -5730,6 +5788,8 @@ static int ixgbe_sw_init(struct ixgbe_adapter *adapter,
 #endif /* IXGBE_FCOE */
 	/* Fall Through */
 	case ixgbe_mac_X550:
+		if (hw->mac.type == ixgbe_mac_X550)
+			adapter->flags2 |= IXGBE_FLAG2_TEMP_SENSOR_CAPABLE;
 #ifdef CONFIG_IXGBE_DCA
 		adapter->flags &= ~IXGBE_FLAG_DCA_CAPABLE;
 #endif
@@ -6807,6 +6867,9 @@ static void ixgbe_watchdog_link_is_up(struct ixgbe_adapter *adapter)
 	case IXGBE_LINK_SPEED_100_FULL:
 		speed_str = "100 Mbps";
 		break;
+	case IXGBE_LINK_SPEED_10_FULL:
+		speed_str = "10 Mbps";
+		break;
 	default:
 		speed_str = "unknown speed";
 		break;
@@ -9595,6 +9658,7 @@ static int ixgbe_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	hw->phy.reset_if_overtemp = true;
 	err = hw->mac.ops.reset_hw(hw);
 	hw->phy.reset_if_overtemp = false;
+	ixgbe_set_eee_capable(adapter);
 	if (err == IXGBE_ERR_SFP_NOT_PRESENT) {
 		err = 0;
 	} else if (err == IXGBE_ERR_SFP_NOT_SUPPORTED) {
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
index 67a399b..2fcde87 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
@@ -784,6 +784,9 @@ s32 ixgbe_setup_phy_link_speed_generic(struct ixgbe_hw *hw,
 	if (speed & IXGBE_LINK_SPEED_100_FULL)
 		hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_100_FULL;
 
+	if (speed & IXGBE_LINK_SPEED_10_FULL)
+		hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10_FULL;
+
 	/* Setup link based on the new speed settings */
 	hw->phy.ops.setup_link(hw);
 
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
index a8f2d70..b2cd8d4 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
@@ -92,6 +92,8 @@
 #define IXGBE_DEV_ID_X550EM_A_SGMII_L	0x15C7
 #define IXGBE_DEV_ID_X550EM_A_10G_T	0x15C8
 #define IXGBE_DEV_ID_X550EM_A_SFP	0x15CE
+#define IXGBE_DEV_ID_X550EM_A_1G_T	0x15E4
+#define IXGBE_DEV_ID_X550EM_A_1G_T_L	0x15E5
 
 /* VF Device IDs */
 #define IXGBE_DEV_ID_82599_VF		0x10ED
@@ -1914,6 +1916,7 @@ enum {
 #define IXGBE_LINKS_SPEED_10G_82599 0x30000000
 #define IXGBE_LINKS_SPEED_1G_82599  0x20000000
 #define IXGBE_LINKS_SPEED_100_82599 0x10000000
+#define IXGBE_LINKS_SPEED_10_X550EM_A 0
 #define IXGBE_LINK_UP_TIME      90 /* 9.0 Seconds */
 #define IXGBE_AUTO_NEG_TIME     45 /* 4.5 Seconds */
 
@@ -2926,6 +2929,7 @@ typedef u32 ixgbe_autoneg_advertised;
 /* Link speed */
 typedef u32 ixgbe_link_speed;
 #define IXGBE_LINK_SPEED_UNKNOWN	0
+#define IXGBE_LINK_SPEED_10_FULL	0x0002
 #define IXGBE_LINK_SPEED_100_FULL	0x0008
 #define IXGBE_LINK_SPEED_1GB_FULL	0x0020
 #define IXGBE_LINK_SPEED_2_5GB_FULL	0x0400
@@ -3141,6 +3145,7 @@ enum ixgbe_phy_type {
 	ixgbe_phy_qsfp_unknown,
 	ixgbe_phy_sfp_unsupported,
 	ixgbe_phy_sgmii,
+	ixgbe_phy_fw,
 	ixgbe_phy_generic
 };
 
@@ -3555,6 +3560,8 @@ struct ixgbe_phy_info {
 	bool                            reset_disable;
 	ixgbe_autoneg_advertised        autoneg_advertised;
 	ixgbe_link_speed		speeds_supported;
+	ixgbe_link_speed		eee_speeds_supported;
+	ixgbe_link_speed		eee_speeds_advertised;
 	enum ixgbe_smart_speed          smart_speed;
 	bool                            smart_speed_active;
 	bool                            multispeed_fiber;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index b9277df..de5cc70 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -63,6 +63,18 @@ static s32 ixgbe_get_invariants_X550_a(struct ixgbe_hw *hw)
 	return 0;
 }
 
+static s32 ixgbe_get_invariants_X550_a_fw(struct ixgbe_hw *hw)
+{
+	struct ixgbe_phy_info *phy = &hw->phy;
+
+	/* Start with X540 invariants, since so similar */
+	ixgbe_get_invariants_X540(hw);
+
+	phy->ops.set_phy_power = NULL;
+
+	return 0;
+}
+
 /** ixgbe_setup_mux_ctl - Setup ESDP register for I2C mux control
  *  @hw: pointer to hardware structure
  **/
@@ -447,6 +459,159 @@ s32 ixgbe_fw_phy_activity(struct ixgbe_hw *hw, u16 activity,
 	return IXGBE_ERR_HOST_INTERFACE_COMMAND;
 }
 
+static const struct {
+	u16 fw_speed;
+	ixgbe_link_speed phy_speed;
+} ixgbe_fw_map[] = {
+	{ FW_PHY_ACT_LINK_SPEED_10, IXGBE_LINK_SPEED_10_FULL },
+	{ FW_PHY_ACT_LINK_SPEED_100, IXGBE_LINK_SPEED_100_FULL },
+	{ FW_PHY_ACT_LINK_SPEED_1G, IXGBE_LINK_SPEED_1GB_FULL },
+	{ FW_PHY_ACT_LINK_SPEED_2_5G, IXGBE_LINK_SPEED_2_5GB_FULL },
+	{ FW_PHY_ACT_LINK_SPEED_5G, IXGBE_LINK_SPEED_5GB_FULL },
+	{ FW_PHY_ACT_LINK_SPEED_10G, IXGBE_LINK_SPEED_10GB_FULL },
+};
+
+/**
+ * ixgbe_get_phy_id_fw - Get the phy ID via firmware command
+ * @hw: pointer to hardware structure
+ *
+ * Returns error code
+ */
+static s32 ixgbe_get_phy_id_fw(struct ixgbe_hw *hw)
+{
+	u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 };
+	u16 phy_speeds;
+	u16 phy_id_lo;
+	s32 rc;
+	u16 i;
+
+	if (hw->phy.id)
+		return 0;
+
+	rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_PHY_INFO, &info);
+	if (rc)
+		return rc;
+
+	hw->phy.speeds_supported = 0;
+	phy_speeds = info[0] & FW_PHY_INFO_SPEED_MASK;
+	for (i = 0; i < ARRAY_SIZE(ixgbe_fw_map); ++i) {
+		if (phy_speeds & ixgbe_fw_map[i].fw_speed)
+			hw->phy.speeds_supported |= ixgbe_fw_map[i].phy_speed;
+	}
+
+	hw->phy.id = info[0] & FW_PHY_INFO_ID_HI_MASK;
+	phy_id_lo = info[1] & FW_PHY_INFO_ID_LO_MASK;
+	hw->phy.id |= phy_id_lo & IXGBE_PHY_REVISION_MASK;
+	hw->phy.revision = phy_id_lo & ~IXGBE_PHY_REVISION_MASK;
+	if (!hw->phy.id || hw->phy.id == IXGBE_PHY_REVISION_MASK)
+		return IXGBE_ERR_PHY_ADDR_INVALID;
+
+	hw->phy.autoneg_advertised = hw->phy.speeds_supported;
+	hw->phy.eee_speeds_supported = IXGBE_LINK_SPEED_100_FULL |
+				       IXGBE_LINK_SPEED_1GB_FULL;
+	hw->phy.eee_speeds_advertised = hw->phy.eee_speeds_supported;
+	return 0;
+}
+
+/**
+ * ixgbe_identify_phy_fw - Get PHY type based on firmware command
+ * @hw: pointer to hardware structure
+ *
+ * Returns error code
+ */
+static s32 ixgbe_identify_phy_fw(struct ixgbe_hw *hw)
+{
+	if (hw->bus.lan_id)
+		hw->phy.phy_semaphore_mask = IXGBE_GSSR_PHY1_SM;
+	else
+		hw->phy.phy_semaphore_mask = IXGBE_GSSR_PHY0_SM;
+
+	hw->phy.type = ixgbe_phy_fw;
+	hw->phy.ops.read_reg = NULL;
+	hw->phy.ops.write_reg = NULL;
+	return ixgbe_get_phy_id_fw(hw);
+}
+
+/**
+ * ixgbe_shutdown_fw_phy - Shutdown a firmware-controlled PHY
+ * @hw: pointer to hardware structure
+ *
+ * Returns error code
+ */
+static s32 ixgbe_shutdown_fw_phy(struct ixgbe_hw *hw)
+{
+	u32 setup[FW_PHY_ACT_DATA_COUNT] = { 0 };
+
+	setup[0] = FW_PHY_ACT_FORCE_LINK_DOWN_OFF;
+	return ixgbe_fw_phy_activity(hw, FW_PHY_ACT_FORCE_LINK_DOWN, &setup);
+}
+
+/**
+ * ixgbe_setup_fw_link - Setup firmware-controlled PHYs
+ * @hw: pointer to hardware structure
+ */
+static s32 ixgbe_setup_fw_link(struct ixgbe_hw *hw)
+{
+	u32 setup[FW_PHY_ACT_DATA_COUNT] = { 0 };
+	s32 rc;
+	u16 i;
+
+	if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw))
+		return 0;
+
+	if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
+		hw_err(hw, "rx_pause not valid in strict IEEE mode\n");
+		return IXGBE_ERR_INVALID_LINK_SETTINGS;
+	}
+
+	switch (hw->fc.requested_mode) {
+	case ixgbe_fc_full:
+		setup[0] |= FW_PHY_ACT_SETUP_LINK_PAUSE_RXTX <<
+			    FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT;
+		break;
+	case ixgbe_fc_rx_pause:
+		setup[0] |= FW_PHY_ACT_SETUP_LINK_PAUSE_RX <<
+			    FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT;
+		break;
+	case ixgbe_fc_tx_pause:
+		setup[0] |= FW_PHY_ACT_SETUP_LINK_PAUSE_TX <<
+			    FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT;
+		break;
+	default:
+		break;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(ixgbe_fw_map); ++i) {
+		if (hw->phy.autoneg_advertised & ixgbe_fw_map[i].phy_speed)
+			setup[0] |= ixgbe_fw_map[i].fw_speed;
+	}
+	setup[0] |= FW_PHY_ACT_SETUP_LINK_HP | FW_PHY_ACT_SETUP_LINK_AN;
+
+	if (hw->phy.eee_speeds_advertised)
+		setup[0] |= FW_PHY_ACT_SETUP_LINK_EEE;
+
+	rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_SETUP_LINK, &setup);
+	if (rc)
+		return rc;
+	if (setup[0] == FW_PHY_ACT_SETUP_LINK_RSP_DOWN)
+		return IXGBE_ERR_OVERTEMP;
+	return 0;
+}
+
+/**
+ * ixgbe_fc_autoneg_fw - Set up flow control for FW-controlled PHYs
+ * @hw: pointer to hardware structure
+ *
+ * Called at init time to set up flow control.
+ */
+static s32 ixgbe_fc_autoneg_fw(struct ixgbe_hw *hw)
+{
+	if (hw->fc.requested_mode == ixgbe_fc_default)
+		hw->fc.requested_mode = ixgbe_fc_full;
+
+	return ixgbe_setup_fw_link(hw);
+}
+
 /** ixgbe_init_eeprom_params_X550 - Initialize EEPROM params
  *  @hw: pointer to hardware structure
  *
@@ -1794,6 +1959,125 @@ ixgbe_setup_sgmii(struct ixgbe_hw *hw, __always_unused ixgbe_link_speed speed,
 	return rc;
 }
 
+/**
+ * ixgbe_setup_sgmii_fw - Set up link for sgmii with firmware-controlled PHYs
+ * @hw: pointer to hardware structure
+ */
+static s32 ixgbe_setup_sgmii_fw(struct ixgbe_hw *hw, ixgbe_link_speed speed,
+				bool autoneg_wait)
+{
+	struct ixgbe_mac_info *mac = &hw->mac;
+	u32 lval, sval, flx_val;
+	s32 rc;
+
+	rc = mac->ops.read_iosf_sb_reg(hw,
+				       IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+				       IXGBE_SB_IOSF_TARGET_KR_PHY, &lval);
+	if (rc)
+		return rc;
+
+	lval &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
+	lval &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_MASK;
+	lval |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_SGMII_EN;
+	lval |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CLAUSE_37_EN;
+	lval &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_1G;
+	rc = mac->ops.write_iosf_sb_reg(hw,
+					IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+					IXGBE_SB_IOSF_TARGET_KR_PHY, lval);
+	if (rc)
+		return rc;
+
+	rc = mac->ops.read_iosf_sb_reg(hw,
+				       IXGBE_KRM_SGMII_CTRL(hw->bus.lan_id),
+				       IXGBE_SB_IOSF_TARGET_KR_PHY, &sval);
+	if (rc)
+		return rc;
+
+	sval &= ~IXGBE_KRM_SGMII_CTRL_MAC_TAR_FORCE_10_D;
+	sval &= ~IXGBE_KRM_SGMII_CTRL_MAC_TAR_FORCE_100_D;
+	rc = mac->ops.write_iosf_sb_reg(hw,
+					IXGBE_KRM_SGMII_CTRL(hw->bus.lan_id),
+					IXGBE_SB_IOSF_TARGET_KR_PHY, sval);
+	if (rc)
+		return rc;
+
+	rc = mac->ops.write_iosf_sb_reg(hw,
+					IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+					IXGBE_SB_IOSF_TARGET_KR_PHY, lval);
+	if (rc)
+		return rc;
+
+	rc = mac->ops.read_iosf_sb_reg(hw,
+				    IXGBE_KRM_PMD_FLX_MASK_ST20(hw->bus.lan_id),
+				    IXGBE_SB_IOSF_TARGET_KR_PHY, &flx_val);
+	if (rc)
+		return rc;
+
+	flx_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_MASK;
+	flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_AN;
+	flx_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_AN_EN;
+	flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SGMII_EN;
+	flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_AN37_EN;
+
+	rc = mac->ops.write_iosf_sb_reg(hw,
+				    IXGBE_KRM_PMD_FLX_MASK_ST20(hw->bus.lan_id),
+				    IXGBE_SB_IOSF_TARGET_KR_PHY, flx_val);
+	if (rc)
+		return rc;
+
+	ixgbe_restart_an_internal_phy_x550em(hw);
+
+	return hw->phy.ops.setup_link_speed(hw, speed, autoneg_wait);
+}
+
+/**
+ * ixgbe_fc_autoneg_sgmii_x550em_a - Enable flow control IEEE clause 37
+ * @hw: pointer to hardware structure
+ *
+ * Enable flow control according to IEEE clause 37.
+ */
+static void ixgbe_fc_autoneg_sgmii_x550em_a(struct ixgbe_hw *hw)
+{
+	s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED;
+	u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 };
+	ixgbe_link_speed speed;
+	bool link_up;
+
+	/* AN should have completed when the cable was plugged in.
+	 * Look for reasons to bail out.  Bail out if:
+	 * - FC autoneg is disabled, or if
+	 * - link is not up.
+	 */
+	if (hw->fc.disable_fc_autoneg)
+		goto out;
+
+	hw->mac.ops.check_link(hw, &speed, &link_up, false);
+	if (!link_up)
+		goto out;
+
+	/* Check if auto-negotiation has completed */
+	status = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &info);
+	if (status || !(info[0] & FW_PHY_ACT_GET_LINK_INFO_AN_COMPLETE)) {
+		status = IXGBE_ERR_FC_NOT_NEGOTIATED;
+		goto out;
+	}
+
+	/* Negotiate the flow control */
+	status = ixgbe_negotiate_fc(hw, info[0], info[0],
+				    FW_PHY_ACT_GET_LINK_INFO_FC_RX,
+				    FW_PHY_ACT_GET_LINK_INFO_FC_TX,
+				    FW_PHY_ACT_GET_LINK_INFO_LP_FC_RX,
+				    FW_PHY_ACT_GET_LINK_INFO_LP_FC_TX);
+
+out:
+	if (!status) {
+		hw->fc.fc_was_autonegged = true;
+	} else {
+		hw->fc.fc_was_autonegged = false;
+		hw->fc.current_mode = hw->fc.requested_mode;
+	}
+}
+
 /** ixgbe_init_mac_link_ops_X550em_a - Init mac link function pointers
  *  @hw: pointer to hardware structure
  **/
@@ -1806,6 +2090,17 @@ static void ixgbe_init_mac_link_ops_X550em_a(struct ixgbe_hw *hw)
 		mac->ops.setup_fc = NULL;
 		mac->ops.fc_autoneg = ixgbe_fc_autoneg_fiber_x550em_a;
 		break;
+	case ixgbe_media_type_copper:
+		if (hw->device_id != IXGBE_DEV_ID_X550EM_A_1G_T &&
+		    hw->device_id != IXGBE_DEV_ID_X550EM_A_1G_T_L) {
+			mac->ops.setup_link = ixgbe_setup_mac_link_t_X550em;
+			break;
+		}
+		mac->ops.fc_autoneg = ixgbe_fc_autoneg_sgmii_x550em_a;
+		mac->ops.setup_fc = ixgbe_fc_autoneg_fw;
+		mac->ops.setup_link = ixgbe_setup_sgmii_fw;
+		mac->ops.check_link = ixgbe_check_mac_link_generic;
+		break;
 	case ixgbe_media_type_backplane:
 		mac->ops.fc_autoneg = ixgbe_fc_autoneg_backplane_x550em_a;
 		mac->ops.setup_fc = ixgbe_setup_fc_backplane_x550em_a;
@@ -1853,7 +2148,7 @@ static void ixgbe_init_mac_link_ops_X550em(struct ixgbe_hw *hw)
 		mac->ops.setup_link = ixgbe_setup_mac_link_t_X550em;
 		mac->ops.setup_fc = ixgbe_setup_fc_generic;
 		mac->ops.check_link = ixgbe_check_link_t_X550em;
-		return;
+		break;
 	case ixgbe_media_type_backplane:
 		if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SGMII ||
 		    hw->device_id == IXGBE_DEV_ID_X550EM_A_SGMII_L)
@@ -1896,6 +2191,12 @@ static s32 ixgbe_get_link_capabilities_X550em(struct ixgbe_hw *hw,
 					      ixgbe_link_speed *speed,
 					      bool *autoneg)
 {
+	if (hw->phy.type == ixgbe_phy_fw) {
+		*autoneg = true;
+		*speed = hw->phy.speeds_supported;
+		return 0;
+	}
+
 	/* SFP */
 	if (hw->phy.media_type == ixgbe_media_type_fiber) {
 		/* CS4227 SFP must not enable auto-negotiation */
@@ -2734,6 +3035,50 @@ static s32 ixgbe_enter_lplu_t_x550em(struct ixgbe_hw *hw)
 }
 
 /**
+ * ixgbe_reset_phy_fw - Reset firmware-controlled PHYs
+ * @hw: pointer to hardware structure
+ */
+static s32 ixgbe_reset_phy_fw(struct ixgbe_hw *hw)
+{
+	u32 store[FW_PHY_ACT_DATA_COUNT] = { 0 };
+	s32 rc;
+
+	if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw))
+		return 0;
+
+	rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_PHY_SW_RESET, &store);
+	if (rc)
+		return rc;
+	memset(store, 0, sizeof(store));
+
+	rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_INIT_PHY, &store);
+	if (rc)
+		return rc;
+
+	return ixgbe_setup_fw_link(hw);
+}
+
+/**
+ * ixgbe_check_overtemp_fw - Check firmware-controlled PHYs for overtemp
+ * @hw: pointer to hardware structure
+ */
+static s32 ixgbe_check_overtemp_fw(struct ixgbe_hw *hw)
+{
+	u32 store[FW_PHY_ACT_DATA_COUNT] = { 0 };
+	s32 rc;
+
+	rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &store);
+	if (rc)
+		return rc;
+
+	if (store[0] & FW_PHY_ACT_GET_LINK_INFO_TEMP) {
+		ixgbe_shutdown_fw_phy(hw);
+		return IXGBE_ERR_OVERTEMP;
+	}
+	return 0;
+}
+
+/**
  * ixgbe_read_mng_if_sel_x550em - Read NW_MNG_IF_SEL register
  * @hw: pointer to hardware structure
  *
@@ -2819,6 +3164,10 @@ static s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw)
 		phy->ops.handle_lasi = ixgbe_handle_lasi_ext_t_x550em;
 		phy->ops.reset = ixgbe_reset_phy_t_X550em;
 		break;
+	case ixgbe_phy_fw:
+		phy->ops.setup_link = ixgbe_setup_fw_link;
+		phy->ops.reset = ixgbe_reset_phy_fw;
+		break;
 	default:
 		break;
 	}
@@ -2856,6 +3205,8 @@ static enum ixgbe_media_type ixgbe_get_media_type_X550em(struct ixgbe_hw *hw)
 	case IXGBE_DEV_ID_X550EM_X_1G_T:
 	case IXGBE_DEV_ID_X550EM_X_10G_T:
 	case IXGBE_DEV_ID_X550EM_A_10G_T:
+	case IXGBE_DEV_ID_X550EM_A_1G_T:
+	case IXGBE_DEV_ID_X550EM_A_1G_T_L:
 		media_type = ixgbe_media_type_copper;
 		break;
 	default:
@@ -2923,6 +3274,13 @@ static void ixgbe_set_mdio_speed(struct ixgbe_hw *hw)
 		hlreg0 &= ~IXGBE_HLREG0_MDCSPD;
 		IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0);
 		break;
+	case IXGBE_DEV_ID_X550EM_A_1G_T:
+	case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+		/* Select fast MDIO clock speed for these devices */
+		hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0);
+		hlreg0 |= IXGBE_HLREG0_MDCSPD;
+		IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0);
+		break;
 	default:
 		break;
 	}
@@ -3434,6 +3792,27 @@ static struct ixgbe_mac_operations mac_ops_x550em_a = {
 	.write_iosf_sb_reg	= ixgbe_write_iosf_sb_reg_x550a,
 };
 
+static struct ixgbe_mac_operations mac_ops_x550em_a_fw = {
+	X550_COMMON_MAC
+	.led_on			= ixgbe_led_on_generic,
+	.led_off		= ixgbe_led_off_generic,
+	.init_led_link_act	= ixgbe_init_led_link_act_generic,
+	.reset_hw		= ixgbe_reset_hw_X550em,
+	.get_media_type		= ixgbe_get_media_type_X550em,
+	.get_san_mac_addr	= NULL,
+	.get_wwn_prefix		= NULL,
+	.setup_link		= NULL, /* defined later */
+	.get_link_capabilities	= ixgbe_get_link_capabilities_X550em,
+	.get_bus_info		= ixgbe_get_bus_info_X550em,
+	.setup_sfp		= ixgbe_setup_sfp_modules_X550em,
+	.acquire_swfw_sync	= ixgbe_acquire_swfw_sync_x550em_a,
+	.release_swfw_sync	= ixgbe_release_swfw_sync_x550em_a,
+	.setup_fc		= ixgbe_setup_fc_x550em,
+	.fc_autoneg		= ixgbe_fc_autoneg,
+	.read_iosf_sb_reg	= ixgbe_read_iosf_sb_reg_x550a,
+	.write_iosf_sb_reg	= ixgbe_write_iosf_sb_reg_x550a,
+};
+
 #define X550_COMMON_EEP \
 	.read			= &ixgbe_read_ee_hostif_X550, \
 	.read_buffer		= &ixgbe_read_ee_hostif_buffer_X550, \
@@ -3463,11 +3842,11 @@ static const struct ixgbe_eeprom_operations eeprom_ops_X550EM_x = {
 	.read_i2c_eeprom	= &ixgbe_read_i2c_eeprom_generic, \
 	.write_i2c_eeprom	= &ixgbe_write_i2c_eeprom_generic, \
 	.setup_link		= &ixgbe_setup_phy_link_generic, \
-	.set_phy_power		= NULL, \
-	.check_overtemp		= &ixgbe_tn_check_overtemp,
+	.set_phy_power		= NULL,
 
 static const struct ixgbe_phy_operations phy_ops_X550 = {
 	X550_COMMON_PHY
+	.check_overtemp		= &ixgbe_tn_check_overtemp,
 	.init			= NULL,
 	.identify		= &ixgbe_identify_phy_generic,
 	.read_reg		= &ixgbe_read_phy_reg_generic,
@@ -3476,6 +3855,7 @@ static const struct ixgbe_phy_operations phy_ops_X550 = {
 
 static const struct ixgbe_phy_operations phy_ops_X550EM_x = {
 	X550_COMMON_PHY
+	.check_overtemp		= &ixgbe_tn_check_overtemp,
 	.init			= &ixgbe_init_phy_ops_X550em,
 	.identify		= &ixgbe_identify_phy_x550em,
 	.read_reg		= &ixgbe_read_phy_reg_generic,
@@ -3484,6 +3864,7 @@ static const struct ixgbe_phy_operations phy_ops_X550EM_x = {
 
 static const struct ixgbe_phy_operations phy_ops_x550em_a = {
 	X550_COMMON_PHY
+	.check_overtemp		= &ixgbe_tn_check_overtemp,
 	.init			= &ixgbe_init_phy_ops_X550em,
 	.identify		= &ixgbe_identify_phy_x550em,
 	.read_reg		= &ixgbe_read_phy_reg_x550a,
@@ -3492,6 +3873,17 @@ static const struct ixgbe_phy_operations phy_ops_x550em_a = {
 	.write_reg_mdi		= &ixgbe_write_phy_reg_mdi,
 };
 
+static const struct ixgbe_phy_operations phy_ops_x550em_a_fw = {
+	X550_COMMON_PHY
+	.check_overtemp		= ixgbe_check_overtemp_fw,
+	.init			= ixgbe_init_phy_ops_X550em,
+	.identify		= ixgbe_identify_phy_fw,
+	.read_reg		= NULL,
+	.write_reg		= NULL,
+	.read_reg_mdi		= NULL,
+	.write_reg_mdi		= NULL,
+};
+
 static const struct ixgbe_link_operations link_ops_x550em_x = {
 	.read_link		= &ixgbe_read_i2c_combined_generic,
 	.read_link_unlocked	= &ixgbe_read_i2c_combined_generic_unlocked,
@@ -3541,3 +3933,13 @@ const struct ixgbe_info ixgbe_x550em_a_info = {
 	.mbx_ops		= &mbx_ops_generic,
 	.mvals			= ixgbe_mvals_x550em_a,
 };
+
+const struct ixgbe_info ixgbe_x550em_a_fw_info = {
+	.mac			= ixgbe_mac_x550em_a,
+	.get_invariants		= ixgbe_get_invariants_X550_a_fw,
+	.mac_ops		= &mac_ops_x550em_a_fw,
+	.eeprom_ops		= &eeprom_ops_X550EM_x,
+	.phy_ops		= &phy_ops_x550em_a_fw,
+	.mbx_ops		= &mbx_ops_generic,
+	.mvals			= ixgbe_mvals_x550em_a,
+};
-- 
2.9.3

[net-next 20/21] ixgbevf: Add support for VF promiscuous mode

[Jeff Kirsher]

From: Don Skidmore <donald.c.skidmore@intel.com>

This patch extends the mailbox message to allow for VF promiscuous
mode support.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbevf/ixgbevf.h      |  1 +
 drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 15 +++++++++++++-
 drivers/net/ethernet/intel/ixgbevf/mbx.h          |  1 +
 drivers/net/ethernet/intel/ixgbevf/vf.c           | 24 +++++++++++++++++++----
 4 files changed, 36 insertions(+), 5 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf.h b/drivers/net/ethernet/intel/ixgbevf/ixgbevf.h
index 5639fbe..3fe6504 100644
--- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf.h
+++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf.h
@@ -464,6 +464,7 @@ enum ixgbevf_xcast_modes {
 	IXGBEVF_XCAST_MODE_NONE = 0,
 	IXGBEVF_XCAST_MODE_MULTI,
 	IXGBEVF_XCAST_MODE_ALLMULTI,
+	IXGBEVF_XCAST_MODE_PROMISC,
 };
 
 extern const struct ixgbevf_info ixgbevf_82599_vf_info;
diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
index 544307c..dbdd938 100644
--- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
+++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
@@ -1930,6 +1930,16 @@ static void ixgbevf_set_rx_mode(struct net_device *netdev)
 		     (flags & (IFF_BROADCAST | IFF_MULTICAST)) ?
 		     IXGBEVF_XCAST_MODE_MULTI : IXGBEVF_XCAST_MODE_NONE;
 
+	/* request the most inclusive mode we need */
+	if (flags & IFF_PROMISC)
+		xcast_mode = IXGBEVF_XCAST_MODE_PROMISC;
+	else if (flags & IFF_ALLMULTI)
+		xcast_mode = IXGBEVF_XCAST_MODE_ALLMULTI;
+	else if (flags & (IFF_BROADCAST | IFF_MULTICAST))
+		xcast_mode = IXGBEVF_XCAST_MODE_MULTI;
+	else
+		xcast_mode = IXGBEVF_XCAST_MODE_NONE;
+
 	spin_lock_bh(&adapter->mbx_lock);
 
 	hw->mac.ops.update_xcast_mode(hw, xcast_mode);
@@ -2071,7 +2081,8 @@ static void ixgbevf_init_last_counter_stats(struct ixgbevf_adapter *adapter)
 static void ixgbevf_negotiate_api(struct ixgbevf_adapter *adapter)
 {
 	struct ixgbe_hw *hw = &adapter->hw;
-	int api[] = { ixgbe_mbox_api_12,
+	int api[] = { ixgbe_mbox_api_13,
+		      ixgbe_mbox_api_12,
 		      ixgbe_mbox_api_11,
 		      ixgbe_mbox_api_10,
 		      ixgbe_mbox_api_unknown };
@@ -2373,6 +2384,7 @@ static void ixgbevf_set_num_queues(struct ixgbevf_adapter *adapter)
 		switch (hw->api_version) {
 		case ixgbe_mbox_api_11:
 		case ixgbe_mbox_api_12:
+		case ixgbe_mbox_api_13:
 			adapter->num_rx_queues = rss;
 			adapter->num_tx_queues = rss;
 		default:
@@ -4117,6 +4129,7 @@ static int ixgbevf_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	switch (adapter->hw.api_version) {
 	case ixgbe_mbox_api_11:
 	case ixgbe_mbox_api_12:
+	case ixgbe_mbox_api_13:
 		netdev->max_mtu = IXGBE_MAX_JUMBO_FRAME_SIZE -
 				  (ETH_HLEN + ETH_FCS_LEN);
 		break;
diff --git a/drivers/net/ethernet/intel/ixgbevf/mbx.h b/drivers/net/ethernet/intel/ixgbevf/mbx.h
index 340cdd4..bc0442a 100644
--- a/drivers/net/ethernet/intel/ixgbevf/mbx.h
+++ b/drivers/net/ethernet/intel/ixgbevf/mbx.h
@@ -84,6 +84,7 @@ enum ixgbe_pfvf_api_rev {
 	ixgbe_mbox_api_20,	/* API version 2.0, solaris Phase1 VF driver */
 	ixgbe_mbox_api_11,	/* API version 1.1, linux/freebsd VF driver */
 	ixgbe_mbox_api_12,	/* API version 1.2, linux/freebsd VF driver */
+	ixgbe_mbox_api_13,	/* API version 1.3, linux/freebsd VF driver */
 	/* This value should always be last */
 	ixgbe_mbox_api_unknown,	/* indicates that API version is not known */
 };
diff --git a/drivers/net/ethernet/intel/ixgbevf/vf.c b/drivers/net/ethernet/intel/ixgbevf/vf.c
index d46ba1d..8a5db9d 100644
--- a/drivers/net/ethernet/intel/ixgbevf/vf.c
+++ b/drivers/net/ethernet/intel/ixgbevf/vf.c
@@ -330,9 +330,14 @@ int ixgbevf_get_reta_locked(struct ixgbe_hw *hw, u32 *reta, int num_rx_queues)
 	 * Thus return an error if API doesn't support RETA querying or querying
 	 * is not supported for this device type.
 	 */
-	if (hw->api_version != ixgbe_mbox_api_12 ||
-	    hw->mac.type >= ixgbe_mac_X550_vf)
+	switch (hw->api_version) {
+	case ixgbe_mbox_api_13:
+	case ixgbe_mbox_api_12:
+		if (hw->mac.type >= ixgbe_mac_X550_vf)
+			break;
+	default:
 		return -EOPNOTSUPP;
+	}
 
 	msgbuf[0] = IXGBE_VF_GET_RETA;
 
@@ -391,9 +396,14 @@ int ixgbevf_get_rss_key_locked(struct ixgbe_hw *hw, u8 *rss_key)
 	 * Thus return an error if API doesn't support RSS Random Key retrieval
 	 * or if the operation is not supported for this device type.
 	 */
-	if (hw->api_version != ixgbe_mbox_api_12 ||
-	    hw->mac.type >= ixgbe_mac_X550_vf)
+	switch (hw->api_version) {
+	case ixgbe_mbox_api_13:
+	case ixgbe_mbox_api_12:
+		if (hw->mac.type >= ixgbe_mac_X550_vf)
+			break;
+	default:
 		return -EOPNOTSUPP;
+	}
 
 	msgbuf[0] = IXGBE_VF_GET_RSS_KEY;
 	err = hw->mbx.ops.write_posted(hw, msgbuf, 1);
@@ -545,6 +555,11 @@ static s32 ixgbevf_update_xcast_mode(struct ixgbe_hw *hw, int xcast_mode)
 
 	switch (hw->api_version) {
 	case ixgbe_mbox_api_12:
+		/* promisc introduced in 1.3 version */
+		if (xcast_mode == IXGBEVF_XCAST_MODE_PROMISC)
+			return -EOPNOTSUPP;
+		/* Fall threw */
+	case ixgbe_mbox_api_13:
 		break;
 	default:
 		return -EOPNOTSUPP;
@@ -884,6 +899,7 @@ int ixgbevf_get_queues(struct ixgbe_hw *hw, unsigned int *num_tcs,
 	switch (hw->api_version) {
 	case ixgbe_mbox_api_11:
 	case ixgbe_mbox_api_12:
+	case ixgbe_mbox_api_13:
 		break;
 	default:
 		return 0;
-- 
2.9.3

[net-next 21/21] ixgbe: Add PF support for VF promiscuous mode

[Jeff Kirsher]

From: Don Skidmore <donald.c.skidmore@intel.com>

This patch extends the xcast mailbox message to include support for
unicast promiscuous mode.  To allow a VF to enter this mode the PF
must be in promiscuous mode.

A later patch will add the support needed in the VF driver (ixgbevf)

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe.h       |  1 +
 drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h   |  1 +
 drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c | 47 ++++++++++++++++++++++----
 drivers/net/ethernet/intel/ixgbe/ixgbe_type.h  |  2 ++
 4 files changed, 45 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe.h b/drivers/net/ethernet/intel/ixgbe/ixgbe.h
index 53fb427..aeedc81 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe.h
@@ -159,6 +159,7 @@ enum ixgbevf_xcast_modes {
 	IXGBEVF_XCAST_MODE_NONE = 0,
 	IXGBEVF_XCAST_MODE_MULTI,
 	IXGBEVF_XCAST_MODE_ALLMULTI,
+	IXGBEVF_XCAST_MODE_PROMISC,
 };
 
 struct vf_macvlans {
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h
index 01c2667..811cb4f 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h
@@ -74,6 +74,7 @@ enum ixgbe_pfvf_api_rev {
 	ixgbe_mbox_api_20,	/* API version 2.0, solaris Phase1 VF driver */
 	ixgbe_mbox_api_11,	/* API version 1.1, linux/freebsd VF driver */
 	ixgbe_mbox_api_12,	/* API version 1.2, linux/freebsd VF driver */
+	ixgbe_mbox_api_13,	/* API version 1.3, linux/freebsd VF driver */
 	/* This value should always be last */
 	ixgbe_mbox_api_unknown,	/* indicates that API version is not known */
 };
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c
index dd1187c..044cb44 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c
@@ -512,6 +512,7 @@ static s32 ixgbe_set_vf_lpe(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf)
 		switch (adapter->vfinfo[vf].vf_api) {
 		case ixgbe_mbox_api_11:
 		case ixgbe_mbox_api_12:
+		case ixgbe_mbox_api_13:
 			/*
 			 * Version 1.1 supports jumbo frames on VFs if PF has
 			 * jumbo frames enabled which means legacy VFs are
@@ -979,6 +980,7 @@ static int ixgbe_negotiate_vf_api(struct ixgbe_adapter *adapter,
 	case ixgbe_mbox_api_10:
 	case ixgbe_mbox_api_11:
 	case ixgbe_mbox_api_12:
+	case ixgbe_mbox_api_13:
 		adapter->vfinfo[vf].vf_api = api;
 		return 0;
 	default:
@@ -1003,6 +1005,7 @@ static int ixgbe_get_vf_queues(struct ixgbe_adapter *adapter,
 	case ixgbe_mbox_api_20:
 	case ixgbe_mbox_api_11:
 	case ixgbe_mbox_api_12:
+	case ixgbe_mbox_api_13:
 		break;
 	default:
 		return -1;
@@ -1042,8 +1045,13 @@ static int ixgbe_get_vf_reta(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf)
 		return -EPERM;
 
 	/* verify the PF is supporting the correct API */
-	if (adapter->vfinfo[vf].vf_api != ixgbe_mbox_api_12)
+	switch (adapter->vfinfo[vf].vf_api) {
+	case ixgbe_mbox_api_13:
+	case ixgbe_mbox_api_12:
+		break;
+	default:
 		return -EOPNOTSUPP;
+	}
 
 	/* This mailbox command is supported (required) only for 82599 and x540
 	 * VFs which support up to 4 RSS queues. Therefore we will compress the
@@ -1069,8 +1077,13 @@ static int ixgbe_get_vf_rss_key(struct ixgbe_adapter *adapter,
 		return -EPERM;
 
 	/* verify the PF is supporting the correct API */
-	if (adapter->vfinfo[vf].vf_api != ixgbe_mbox_api_12)
+	switch (adapter->vfinfo[vf].vf_api) {
+	case ixgbe_mbox_api_13:
+	case ixgbe_mbox_api_12:
+		break;
+	default:
 		return -EOPNOTSUPP;
+	}
 
 	memcpy(rss_key, adapter->rss_key, sizeof(adapter->rss_key));
 
@@ -1082,11 +1095,16 @@ static int ixgbe_update_vf_xcast_mode(struct ixgbe_adapter *adapter,
 {
 	struct ixgbe_hw *hw = &adapter->hw;
 	int xcast_mode = msgbuf[1];
-	u32 vmolr, disable, enable;
+	u32 vmolr, fctrl, disable, enable;
 
 	/* verify the PF is supporting the correct APIs */
 	switch (adapter->vfinfo[vf].vf_api) {
 	case ixgbe_mbox_api_12:
+		/* promisc introduced in 1.3 version */
+		if (xcast_mode == IXGBEVF_XCAST_MODE_PROMISC)
+			return -EOPNOTSUPP;
+		/* Fall threw */
+	case ixgbe_mbox_api_13:
 		break;
 	default:
 		return -EOPNOTSUPP;
@@ -1102,17 +1120,34 @@ static int ixgbe_update_vf_xcast_mode(struct ixgbe_adapter *adapter,
 
 	switch (xcast_mode) {
 	case IXGBEVF_XCAST_MODE_NONE:
-		disable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE | IXGBE_VMOLR_MPE;
+		disable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE |
+			  IXGBE_VMOLR_MPE | IXGBE_VMOLR_UPE | IXGBE_VMOLR_VPE;
 		enable = 0;
 		break;
 	case IXGBEVF_XCAST_MODE_MULTI:
-		disable = IXGBE_VMOLR_MPE;
+		disable = IXGBE_VMOLR_MPE | IXGBE_VMOLR_UPE | IXGBE_VMOLR_VPE;
 		enable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE;
 		break;
 	case IXGBEVF_XCAST_MODE_ALLMULTI:
-		disable = 0;
+		disable = IXGBE_VMOLR_UPE | IXGBE_VMOLR_VPE;
 		enable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE | IXGBE_VMOLR_MPE;
 		break;
+	case IXGBEVF_XCAST_MODE_PROMISC:
+		if (hw->mac.type <= ixgbe_mac_82599EB)
+			return -EOPNOTSUPP;
+
+		fctrl = IXGBE_READ_REG(hw, IXGBE_FCTRL);
+		if (!(fctrl & IXGBE_FCTRL_UPE)) {
+			/* VF promisc requires PF in promisc */
+			e_warn(drv,
+			       "Enabling VF promisc requires PF in promisc\n");
+			return -EPERM;
+		}
+
+		disable = 0;
+		enable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE |
+			 IXGBE_VMOLR_MPE | IXGBE_VMOLR_UPE | IXGBE_VMOLR_VPE;
+		break;
 	default:
 		return -EOPNOTSUPP;
 	}
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
index b2cd8d4..1d07f2e 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
@@ -1501,6 +1501,8 @@ enum {
 #define IXGBE_VT_CTL_POOL_MASK  (0x3F << IXGBE_VT_CTL_POOL_SHIFT)
 
 /* VMOLR bitmasks */
+#define IXGBE_VMOLR_UPE		0x00400000 /* unicast promiscuous */
+#define IXGBE_VMOLR_VPE		0x00800000 /* VLAN promiscuous */
 #define IXGBE_VMOLR_AUPE        0x01000000 /* accept untagged packets */
 #define IXGBE_VMOLR_ROMPE       0x02000000 /* accept packets in MTA tbl */
 #define IXGBE_VMOLR_ROPE        0x04000000 /* accept packets in UC tbl */
-- 
2.9.3