From: Andrew Lunn <andrew@lunn.ch>
To: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: shuah@kernel.org, davem@davemloft.net,
linux-kselftest@vger.kernel.org, linux-kernel@vger.kernel.org,
netdev@vger.kernel.org
Subject: Re: [PATCH v2] selftests: add a generic testsuite for ethernet device
Date: Tue, 4 Apr 2017 16:24:54 +0200 [thread overview]
Message-ID: <20170404142454.GC1736@lunn.ch> (raw)
In-Reply-To: <20170404133247.28725-1-clabbe.montjoie@gmail.com>
On Tue, Apr 04, 2017 at 03:32:47PM +0200, Corentin Labbe wrote:
> This patch add a generic testsuite for testing ethernet network device driver.
# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAUL0
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFA2
link/ether 94:10:3e:80:bc:f3 brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFA2
link/ether a2:e2:da:92:7e:8c brd ff:ff:ff:ff:ff:ff
4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default0
link/sit 0.0.0.0 brd 0.0.0.0
5: lan4@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state 0
link/ether 94:10:3e:80:bc:f3 brd ff:ff:ff:ff:ff:ff
6: lan3@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT0
link/ether 94:10:3e:80:bc:f3 brd ff:ff:ff:ff:ff:ff
7: lan2@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state 0
link/ether 94:10:3e:80:bc:f3 brd ff:ff:ff:ff:ff:ff
8: lan1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP0
link/ether 94:10:3e:80:bc:f3 brd ff:ff:ff:ff:ff:ff
9: internet@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue st0
link/ether 94:10:3e:80:bc:f3 brd ff:ff:ff:ff:ff:ff
# /home/andrew/netdevice.sh
[ 151.417351] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
PASS: eth0: set interface up
PASS: eth0: set MAC address
SKIP: eth0: set IP address
PASS: eth0: ethtool list features
Cannot get register dump: Operation not supported
SKIP: eth0: ethtool dump not supported
PASS: eth0: ethtool stats
PASS: eth0: stop interface
SKIP: eth1: interface already up
PASS: eth1: ethtool list features
Cannot get register dump: Operation not supported
SKIP: eth1: ethtool dump not supported
PASS: eth1: ethtool stats
SKIP: eth1: interface kept up
PASS: eth0: set interface up
PASS: lan4: set MAC address
inet 192.168.13.2/24 brd 192.168.13.255 scope global lan4
SKIP: lan4: already have an IP
PASS: lan4: ethtool list features
PASS: lan4: ethtool dump
PASS: lan4: ethtool stats
PASS: eth0: stop interface
PASS: eth0: set interface up
PASS: lan3: set MAC address
SKIP: lan3: set IP address
PASS: lan3: ethtool list features
PASS: lan3: ethtool dump
PASS: lan3: ethtool stats
PASS: eth0: stop interface
PASS: eth0: set interface up
PASS: lan2: set MAC address
SKIP: lan2: set IP address
PASS: lan2: ethtool list features
PASS: lan2: ethtool dump
PASS: lan2: ethtool stats
PASS: eth0: stop interface
PASS: eth0: set interface up
PASS: lan1: set MAC address
inet 10.0.0.12/24 brd 10.0.0.255 scope global lan1
SKIP: lan1: already have an IP
PASS: lan1: ethtool list features
PASS: lan1: ethtool dump
PASS: lan1: ethtool stats
PASS: eth0: stop interface
PASS: eth0: set interface up
PASS: internet: set MAC address
inet 192.168.10.2/24 brd 192.168.10.255 scope global internet
SKIP: internet: already have an IP
PASS: internet: ethtool list features
PASS: internet: ethtool dump
PASS: internet: ethtool stats
PASS: eth0: stop interface
Cool
Tested-by: Andrew Lunn <andrew@lunn.ch>
Andrew
next prev parent reply other threads:[~2017-04-04 14:25 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-04-04 13:32 [PATCH v2] selftests: add a generic testsuite for ethernet device Corentin Labbe
2017-04-04 14:24 ` Andrew Lunn [this message]
2017-04-04 14:43 ` Niklas Cassel
2017-04-04 14:50 ` Corentin Labbe
2017-04-04 15:00 ` Andrew Lunn
2017-04-05 15:30 ` David Miller
2017-06-29 8:26 ` Fathi Boudra
2017-07-01 6:42 ` Corentin Labbe
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170404142454.GC1736@lunn.ch \
--to=andrew@lunn.ch \
--cc=clabbe.montjoie@gmail.com \
--cc=davem@davemloft.net \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-kselftest@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=shuah@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).