netdev.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Stephen Hemminger <stephen@networkplumber.org>
To: Salil Mehta <salil.mehta@huawei.com>
Cc: <davem@davemloft.net>, <yisen.zhuang@huawei.com>,
	<huangdaode@hisilicon.com>, <lipeng321@huawei.com>,
	<mehta.salil.lnk@gmail.com>, <netdev@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>, <linuxarm@huawei.com>
Subject: Re: [PATCH V3 net-next 2/8] net: hns3: Add support of the HNAE3 framework
Date: Mon, 19 Jun 2017 09:59:02 -0700	[thread overview]
Message-ID: <20170619095902.5fadbe42@xeon-e3> (raw)
In-Reply-To: <20170617172431.177044-3-salil.mehta@huawei.com>

On Sat, 17 Jun 2017 18:24:25 +0100
Salil Mehta <salil.mehta@huawei.com> wrote:

> +
> +/* This struct defines the operation on the handle.
> + *
> + * init_ae_dev(): (mandatory)
> + *   Get PF configure from pci_dev and initialize PF hardware
> + * uninit_ae_dev()
> + *   Disable PF device and release PF resource
> + * register_client
> + *   Register client to ae_dev
> + * unregister_client()
> + *   Unregister client from ae_dev
> + * start()
> + *   Enable the hardware
> + * stop()
> + *   Disable the hardware
> + * get_status()
> + *   Get the carrier state of the back channel of the handle, 1 for ok, 0 for
> + *   non-ok
> + * get_ksettings_an_result()
> + *   Get negotiation status,speed and duplex
> + * update_speed_duplex_h()
> + *   Update hardware speed and duplex
> + * get_media_type()
> + *   Get media type of MAC
> + * adjust_link()
> + *   Adjust link status
> + * set_loopback()
> + *   Set loopback
> + * set_promisc_mode
> + *   Set promisc mode
> + * set_mtu()
> + *   set mtu
> + * get_pauseparam()
> + *   get tx and rx of pause frame use
> + * set_pauseparam()
> + *   set tx and rx of pause frame use
> + * set_autoneg()
> + *   set auto autonegotiation of pause frame use
> + * get_autoneg()
> + *   get auto autonegotiation of pause frame use
> + * get_coalesce_usecs()
> + *   get usecs to delay a TX interrupt after a packet is sent
> + * get_rx_max_coalesced_frames()
> + *   get Maximum number of packets to be sent before a TX interrupt.
> + * set_coalesce_usecs()
> + *   set usecs to delay a TX interrupt after a packet is sent
> + * set_coalesce_frames()
> + *   set Maximum number of packets to be sent before a TX interrupt.
> + * get_mac_addr()
> + *   get mac address
> + * set_mac_addr()
> + *   set mac address
> + * add_uc_addr
> + *   Add unicast addr to mac table
> + * rm_uc_addr
> + *   Remove unicast addr from mac table
> + * set_mc_addr()
> + *   Set multicast address
> + * add_mc_addr
> + *   Add multicast address to mac table
> + * rm_mc_addr
> + *   Remove multicast address from mac table
> + * update_stats()
> + *   Update Old network device statistics
> + * get_ethtool_stats()
> + *   Get ethtool network device statistics
> + * get_strings()
> + *   Get a set of strings that describe the requested objects
> + * get_sset_count()
> + *   Get number of strings that @get_strings will write
> + * update_led_status()
> + *   Update the led status
> + * set_led_id()
> + *   Set led id
> + * get_regs()
> + *   Get regs dump
> + * get_regs_len()
> + *   Get the len of the regs dump
> + * get_rss_key_size()
> + *   Get rss key size
> + * get_rss_indir_size()
> + *   Get rss indirection table size
> + * get_rss()
> + *   Get rss table
> + * set_rss()
> + *   Set rss table
> + * get_tc_size()
> + *   Get tc size of handle
> + * get_vector()
> + *   Get vector number and vector infomation
> + * map_ring_to_vector()
> + *   Map rings to vector
> + * unmap_ring_from_vector()
> + *   Unmap rings from vector
> + * add_tunnel_udp()
> + *   Add tunnel information to hardware
> + * del_tunnel_udp()
> + *   Delete tunnel information from hardware
> + * reset_queue()
> + *   Reset queue
> + * get_fw_version()
> + *   Get firmware version
> + * get_mdix_mode()
> + *   Get media typr of phy
> + * set_vlan_filter()
> + *   Set vlan filter config of Ports
> + * set_vf_vlan_filter()
> + *   Set vlan filter config of vf
> + */
> +struct hnae3_ae_ops {
> +	int (*init_ae_dev)(struct hnae3_ae_dev *ae_dev);
> +	void (*uninit_ae_dev)(struct hnae3_ae_dev *ae_dev);
> +
> +	int (*register_client)(struct hnae3_client *client,
> +			       struct hnae3_ae_dev *ae_dev);
> +	void (*unregister_client)(struct hnae3_client *client,
> +				  struct hnae3_ae_dev *ae_dev);
> +	int (*start)(struct hnae3_handle *handle);
> +	void (*stop)(struct hnae3_handle *handle);
> +	int (*get_status)(struct hnae3_handle *handle);
> +	void (*get_ksettings_an_result)(struct hnae3_handle *handle,
> +					u8 *auto_neg, u32 *speed, u8 *duplex);
> +
> +	int (*update_speed_duplex_h)(struct hnae3_handle *handle);
> +	int (*cfg_mac_speed_dup_h)(struct hnae3_handle *handle, int speed,
> +				   u8 duplex);
> +
> +	void (*get_media_type)(struct hnae3_handle *handle, u8 *media_type);
> +	void (*adjust_link)(struct hnae3_handle *handle, int speed, int duplex);
> +	int (*set_loopback)(struct hnae3_handle *handle,
> +			    enum hnae3_loop loop_mode, bool en);
> +
> +	void (*set_promisc_mode)(struct hnae3_handle *handle, u32 en);
> +	int (*set_mtu)(struct hnae3_handle *handle, int new_mtu);
> +
> +	void (*get_pauseparam)(struct hnae3_handle *handle,
> +			       u32 *auto_neg, u32 *rx_en, u32 *tx_en);
> +	int (*set_pauseparam)(struct hnae3_handle *handle,
> +			      u32 auto_neg, u32 rx_en, u32 tx_en);
> +
> +	int (*set_autoneg)(struct hnae3_handle *handle, bool enable);
> +	int (*get_autoneg)(struct hnae3_handle *handle);
> +
> +	void (*get_coalesce_usecs)(struct hnae3_handle *handle,
> +				   u32 *tx_usecs, u32 *rx_usecs);
> +	void (*get_rx_max_coalesced_frames)(struct hnae3_handle *handle,
> +					    u32 *tx_frames, u32 *rx_frames);
> +	int (*set_coalesce_usecs)(struct hnae3_handle *handle, u32 timeout);
> +	int (*set_coalesce_frames)(struct hnae3_handle *handle,
> +				   u32 coalesce_frames);
> +	void (*get_coalesce_range)(struct hnae3_handle *handle,
> +				   u32 *tx_frames_low, u32 *rx_frames_low,
> +				   u32 *tx_frames_high, u32 *rx_frames_high,
> +				   u32 *tx_usecs_low, u32 *rx_usecs_low,
> +				   u32 *tx_usecs_high, u32 *rx_usecs_high);
> +
> +	void (*get_mac_addr)(struct hnae3_handle *handle, u8 *p);
> +	int (*set_mac_addr)(struct hnae3_handle *handle, void *p);
> +	int (*add_uc_addr)(struct hnae3_handle *handle,
> +			   const unsigned char *addr);
> +	int (*rm_uc_addr)(struct hnae3_handle *handle,
> +			  const unsigned char *addr);
> +	int (*set_mc_addr)(struct hnae3_handle *handle, void *addr);
> +	int (*add_mc_addr)(struct hnae3_handle *handle,
> +			   const unsigned char *addr);
> +	int (*rm_mc_addr)(struct hnae3_handle *handle,
> +			  const unsigned char *addr);
> +
> +	void (*set_tso_stats)(struct hnae3_handle *handle, int enable);
> +	void (*update_stats)(struct hnae3_handle *handle,
> +			     struct net_device_stats *net_stats);
> +	void (*get_stats)(struct hnae3_handle *handle, u64 *data);
> +
> +	void (*get_strings)(struct hnae3_handle *handle,
> +			    u32 stringset, u8 *data);
> +	int (*get_sset_count)(struct hnae3_handle *handle, int stringset);
> +
> +	void (*get_regs)(struct hnae3_handle *handle, void *data);
> +	int (*get_regs_len)(struct hnae3_handle *handle);
> +
> +	u32 (*get_rss_key_size)(struct hnae3_handle *handle);
> +	u32 (*get_rss_indir_size)(struct hnae3_handle *handle);
> +	int (*get_rss)(struct hnae3_handle *handle, u32 *indir, u8 *key,
> +		       u8 *hfunc);
> +	int (*set_rss)(struct hnae3_handle *handle, const u32 *indir,
> +		       const u8 *key, const u8 hfunc);
> +
> +	int (*get_tc_size)(struct hnae3_handle *handle);
> +
> +	int (*get_vector)(struct hnae3_handle *handle, u16 vector_num,
> +			  struct hnae3_vector_info *vector_info);
> +	int (*map_ring_to_vector)(struct hnae3_handle *handle,
> +				  int vector_num,
> +				  struct hnae3_ring_chain_node *vr_chain);
> +	int (*unmap_ring_from_vector)(struct hnae3_handle *handle,
> +				      int vector_num,
> +				      struct hnae3_ring_chain_node *vr_chain);
> +
> +	int (*add_tunnel_udp)(struct hnae3_handle *handle, u16 port_num);
> +	int (*del_tunnel_udp)(struct hnae3_handle *handle, u16 port_num);
> +
> +	void (*reset_queue)(struct hnae3_handle *handle, u16 queue_id);
> +	u32 (*get_fw_version)(struct hnae3_handle *handle);
> +	void (*get_mdix_mode)(struct hnae3_handle *handle,
> +			      u8 *tp_mdix_ctrl, u8 *tp_mdix);
> +
> +	int (*set_vlan_filter)(struct hnae3_handle *handle, __be16 proto,
> +			       u16 vlan_id, bool is_kill);
> +	int (*set_vf_vlan_filter)(struct hnae3_handle *handle, int vfid,
> +				  u16 vlan, u8 qos, __be16 proto);
> +};
> +


Since ae_ops contains only function pointers. All definitions of it must be const
(and therefore pointers as well).

  parent reply	other threads:[~2017-06-19 16:59 UTC|newest]

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-06-17 17:24 [PATCH V3 net-next 0/8] Hisilicon Network Subsystem 3 Ethernet Driver Salil Mehta
2017-06-17 17:24 ` [PATCH V3 net-next 1/8] net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC Salil Mehta
2017-06-17 17:54   ` Andrew Lunn
2017-07-22 23:17     ` Salil Mehta
2017-06-17 19:41   ` Andrew Lunn
2017-06-19  0:18   ` Bo Yu
2017-07-22 23:34     ` Salil Mehta
2017-06-19  0:57   ` Bo Yu
2017-07-22 23:39     ` Salil Mehta
2017-06-17 17:24 ` [PATCH V3 net-next 2/8] net: hns3: Add support of the HNAE3 framework Salil Mehta
2017-06-17 19:45   ` Andrew Lunn
2017-07-22 23:30     ` Salil Mehta
2017-06-18 15:02   ` Andrew Lunn
2017-07-22 23:32     ` Salil Mehta
2017-06-19  0:40   ` Bo Yu
2017-07-22 23:36     ` Salil Mehta
2017-06-19 16:59   ` Stephen Hemminger [this message]
2017-07-22 23:58     ` Salil Mehta
2017-06-17 17:24 ` [PATCH V3 net-next 3/8] net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd Interface Support Salil Mehta
2017-06-17 17:24 ` [PATCH V3 net-next 4/8] net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support Salil Mehta
2017-06-17 17:24 ` [PATCH V3 net-next 5/8] net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver Salil Mehta
2017-06-18 16:45   ` Richard Cochran
2017-07-22 23:38     ` Salil Mehta
2017-07-23  6:13       ` Richard Cochran
2017-06-17 17:24 ` [PATCH V3 net-next 6/8] net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC Salil Mehta
2017-06-19  3:52   ` Andrew Lunn
2017-07-22 23:53     ` Salil Mehta
2017-06-17 17:24 ` [PATCH V3 net-next 7/8] net: hns3: Add Ethtool support to HNS3 driver Salil Mehta
2017-06-17 17:24 ` [PATCH V3 net-next 8/8] net: hns3: Add HNS3 driver to kernel build framework & MAINTAINERS Salil Mehta
2017-06-18  6:07 ` [PATCH V3 net-next 0/8] Hisilicon Network Subsystem 3 Ethernet Driver Leon Romanovsky

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20170619095902.5fadbe42@xeon-e3 \
    --to=stephen@networkplumber.org \
    --cc=davem@davemloft.net \
    --cc=huangdaode@hisilicon.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linuxarm@huawei.com \
    --cc=lipeng321@huawei.com \
    --cc=mehta.salil.lnk@gmail.com \
    --cc=netdev@vger.kernel.org \
    --cc=salil.mehta@huawei.com \
    --cc=yisen.zhuang@huawei.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).