Netdev List
 help / color / mirror / Atom feed
From: Jiri Pirko <jiri@resnulli.us>
To: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Ido Schimmel <idosch@mellanox.com>,
	netdev@vger.kernel.org, davem@davemloft.net,
	stephen@networkplumber.org, jiri@mellanox.com,
	yotamg@mellanox.com, mlxsw@mellanox.com,
	bridge@lists.linux-foundation.org
Subject: Re: [PATCH net] bridge: switchdev: Clear forward mark when transmitting packet
Date: Fri, 1 Sep 2017 14:01:20 +0200	[thread overview]
Message-ID: <20170901120120.GA1962@nanopsycho> (raw)
In-Reply-To: <0384baf6-0786-2d07-8919-fdd1ca5d88eb@cumulusnetworks.com>

Fri, Sep 01, 2017 at 01:45:15PM CEST, nikolay@cumulusnetworks.com wrote:
>On 01/09/17 12:22, Ido Schimmel wrote:
>> Commit 6bc506b4fb06 ("bridge: switchdev: Add forward mark support for
>> stacked devices") added the 'offload_fwd_mark' bit to the skb in order
>> to allow drivers to indicate to the bridge driver that they already
>> forwarded the packet in L2.
>> 
>> In case the bit is set, before transmitting the packet from each port,
>> the port's mark is compared with the mark stored in the skb's control
>> block. If both marks are equal, we know the packet arrived from a switch
>> device that already forwarded the packet and it's not re-transmitted.
>> 
>> However, if the packet is transmitted from the bridge device itself
>> (e.g., br0), we should clear the 'offload_fwd_mark' bit as the mark
>> stored in the skb's control block isn't valid.
>> 
>> This scenario can happen in rare cases where a packet was trapped during
>> L3 forwarding and forwarded by the kernel to a bridge device.
>> 
>> Fixes: 6bc506b4fb06 ("bridge: switchdev: Add forward mark support for stacked devices")
>> Signed-off-by: Ido Schimmel <idosch@mellanox.com>
>> Reported-by: Yotam Gigi <yotamg@mellanox.com>
>> Tested-by: Yotam Gigi <yotamg@mellanox.com>
>> Reviewed-by: Jiri Pirko <jiri@mellanox.com>
>> ---
>>  net/bridge/br_device.c | 3 +++
>>  1 file changed, 3 insertions(+)
>> 
>> diff --git a/net/bridge/br_device.c b/net/bridge/br_device.c
>> index 861ae2a165f4..5a7be3bddfa9 100644
>> --- a/net/bridge/br_device.c
>> +++ b/net/bridge/br_device.c
>> @@ -53,6 +53,9 @@ netdev_tx_t br_dev_xmit(struct sk_buff *skb, struct net_device *dev)
>>  	brstats->tx_bytes += skb->len;
>>  	u64_stats_update_end(&brstats->syncp);
>>  
>> +#ifdef CONFIG_NET_SWITCHDEV
>> +	skb->offload_fwd_mark = 0;
>> +#endif
>>  	BR_INPUT_SKB_CB(skb)->brdev = dev;
>>  
>>  	skb_reset_mac_header(skb);
>> 
>
>Good catch, just one minor nit since there is already an ifdef
>switchdev/else in br_private.h, why not make this a helper and avoid the
>ifdef/endif in here ? Currently there is no ifdef switchdev anywhere else.

I think it would be better to convert this to a helper in -net-next and
take the patch as it is for -net

  reply	other threads:[~2017-09-01 12:01 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-09-01  9:22 [PATCH net] bridge: switchdev: Clear forward mark when transmitting packet Ido Schimmel
2017-09-01 11:45 ` Nikolay Aleksandrov
2017-09-01 12:01   ` Jiri Pirko [this message]
2017-09-01 12:03     ` Nikolay Aleksandrov
2017-09-01 17:12 ` David Miller

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20170901120120.GA1962@nanopsycho \
    --to=jiri@resnulli.us \
    --cc=bridge@lists.linux-foundation.org \
    --cc=davem@davemloft.net \
    --cc=idosch@mellanox.com \
    --cc=jiri@mellanox.com \
    --cc=mlxsw@mellanox.com \
    --cc=netdev@vger.kernel.org \
    --cc=nikolay@cumulusnetworks.com \
    --cc=stephen@networkplumber.org \
    --cc=yotamg@mellanox.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox