[net-next 0/7][pull request] 100GbE Intel Wired LAN Driver Updates 2018-01-24

[net-next 0/7][pull request] 100GbE Intel Wired LAN Driver Updates 2018-01-24

[Jeff Kirsher]

This series contains updates to fm10k only.

Alex fixes MACVLAN offload for fm10k, where we were not seeing unicast
packets being received because we did not correctly configure the
default VLAN ID for the port and defaulting to 0.

Jake cleans up unnecessary parenthesis in a couple of "if" statements.
Fixed the driver to stop adding VLAN 0 into the VLAN table, since it
would cause the VLAN table to be inconsistent between the PF and VF.
Also fixed an issue where we were assuming that VLAN 1 is enabled when
the default VLAN ID is not set, so resolve by not requesting any filters
for the default_vid if it has not yet been assigned.

Ngai fixes an issue which was generating a dmesg regarding unbale to
kill a particular VLAN ID for the device.  This is due to
ndo_vlan_rx_kill_vid() exits with an error and the handler for this ndo
is fm10k_update_vid() which exits prematurely under PF VLAN management.
So to resolve, we must check the VLAN update action type before exiting
fm10k_update_vid(), and act appropriately based on the action type.
Also corrected code comment typos.

The following are changes since commit 46410c2efa9cb5b2f40c9ce24a75d147f44aedeb:
  Merge branch 'pktgen-Behavior-flags-fixes'
and are available in the git repository at:
  git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue 100GbE

Alexander Duyck (1):
  fm10k: Fix configuration for macvlan offload

Jacob Keller (3):
  fm10k: cleanup unnecessary parenthesis in fm10k_iov.c
  fm10k: stop adding VLAN 0 to the VLAN table
  fm10k: don't assume VLAN 1 is enabled

Ngai-Mint Kwan (3):
  fm10k: fix "failed to kill vid" message for VF
  fm10k: correct typo in fm10k_pf.c
  fm10k: clarify action when updating the VLAN table

 drivers/net/ethernet/intel/fm10k/fm10k_iov.c    |  4 +-
 drivers/net/ethernet/intel/fm10k/fm10k_netdev.c | 54 ++++++++++++++++++-------
 drivers/net/ethernet/intel/fm10k/fm10k_pf.c     |  2 +-
 3 files changed, 43 insertions(+), 17 deletions(-)

-- 
2.14.3

[net-next 1/7] fm10k: Fix configuration for macvlan offload

[Jeff Kirsher]

From: Alexander Duyck <alexander.h.duyck@intel.com>

The fm10k driver didn't work correctly when macvlan offload was enabled.
Specifically what would occur is that we would see no unicast packets being
received. This was traced down to us not correctly configuring the default
VLAN ID for the port and defaulting to 0.

To correct this we either use the default ID provided by the switch or
simply use 1. With that we are able to pass and receive traffic without any
issues.

In addition we were not repopulating the filter table following a reset. To
correct that I have added a bit of code to fm10k_restore_rx_state that will
repopulate the Rx filter configuration for the macvlan interfaces.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/fm10k/fm10k_netdev.c | 25 ++++++++++++++++++++++---
 1 file changed, 22 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c b/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
index adc62fb38c49..6d9088956407 100644
--- a/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
+++ b/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
@@ -1182,9 +1182,10 @@ static void fm10k_set_rx_mode(struct net_device *dev)
 
 void fm10k_restore_rx_state(struct fm10k_intfc *interface)
 {
+	struct fm10k_l2_accel *l2_accel = interface->l2_accel;
 	struct net_device *netdev = interface->netdev;
 	struct fm10k_hw *hw = &interface->hw;
-	int xcast_mode;
+	int xcast_mode, i;
 	u16 vid, glort;
 
 	/* record glort for this interface */
@@ -1234,6 +1235,24 @@ void fm10k_restore_rx_state(struct fm10k_intfc *interface)
 	__dev_uc_sync(netdev, fm10k_uc_sync, fm10k_uc_unsync);
 	__dev_mc_sync(netdev, fm10k_mc_sync, fm10k_mc_unsync);
 
+	/* synchronize macvlan addresses */
+	if (l2_accel) {
+		for (i = 0; i < l2_accel->size; i++) {
+			struct net_device *sdev = l2_accel->macvlan[i];
+
+			if (!sdev)
+				continue;
+
+			glort = l2_accel->dglort + 1 + i;
+
+			hw->mac.ops.update_xcast_mode(hw, glort,
+						      FM10K_XCAST_MODE_MULTI);
+			fm10k_queue_mac_request(interface, glort,
+						sdev->dev_addr,
+						hw->mac.default_vid, true);
+		}
+	}
+
 	fm10k_mbx_unlock(interface);
 
 	/* record updated xcast mode state */
@@ -1490,7 +1509,7 @@ static void *fm10k_dfwd_add_station(struct net_device *dev,
 		hw->mac.ops.update_xcast_mode(hw, glort,
 					      FM10K_XCAST_MODE_MULTI);
 		fm10k_queue_mac_request(interface, glort, sdev->dev_addr,
-					0, true);
+					hw->mac.default_vid, true);
 	}
 
 	fm10k_mbx_unlock(interface);
@@ -1530,7 +1549,7 @@ static void fm10k_dfwd_del_station(struct net_device *dev, void *priv)
 		hw->mac.ops.update_xcast_mode(hw, glort,
 					      FM10K_XCAST_MODE_NONE);
 		fm10k_queue_mac_request(interface, glort, sdev->dev_addr,
-					0, false);
+					hw->mac.default_vid, false);
 	}
 
 	fm10k_mbx_unlock(interface);
-- 
2.14.3

[net-next 2/7] fm10k: cleanup unnecessary parenthesis in fm10k_iov.c

[Jeff Kirsher]

From: Jacob Keller <jacob.e.keller@intel.com>

This fixes a few warnings found by checkpatch.pl --strict

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/fm10k/fm10k_iov.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/fm10k/fm10k_iov.c b/drivers/net/ethernet/intel/fm10k/fm10k_iov.c
index ea3ab24265ee..760cfa52d02c 100644
--- a/drivers/net/ethernet/intel/fm10k/fm10k_iov.c
+++ b/drivers/net/ethernet/intel/fm10k/fm10k_iov.c
@@ -353,7 +353,7 @@ int fm10k_iov_resume(struct pci_dev *pdev)
 		struct fm10k_vf_info *vf_info = &iov_data->vf_info[i];
 
 		/* allocate all but the last GLORT to the VFs */
-		if (i == ((~hw->mac.dglort_map) >> FM10K_DGLORTMAP_MASK_SHIFT))
+		if (i == (~hw->mac.dglort_map >> FM10K_DGLORTMAP_MASK_SHIFT))
 			break;
 
 		/* assign GLORT to VF, and restrict it to multicast */
@@ -511,7 +511,7 @@ int fm10k_iov_configure(struct pci_dev *pdev, int num_vfs)
 		return err;
 
 	/* allocate VFs if not already allocated */
-	if (num_vfs && (num_vfs != current_vfs)) {
+	if (num_vfs && num_vfs != current_vfs) {
 		/* Disable completer abort error reporting as
 		 * the VFs can trigger this any time they read a queue
 		 * that they don't own.
-- 
2.14.3

Re: [net-next 2/7] fm10k: cleanup unnecessary parenthesis in fm10k_iov.c

[Joe Perches]

On Wed, 2018-01-24 at 14:45 -0800, Jeff Kirsher wrote:
> This fixes a few warnings found by checkpatch.pl --strict
[]
> diff --git a/drivers/net/ethernet/intel/fm10k/fm10k_iov.c b/drivers/net/ethernet/intel/fm10k/fm10k_iov.c
[]
> @@ -353,7 +353,7 @@ int fm10k_iov_resume(struct pci_dev *pdev)
>  		struct fm10k_vf_info *vf_info = &iov_data->vf_info[i];
>  
>  		/* allocate all but the last GLORT to the VFs */
> -		if (i == ((~hw->mac.dglort_map) >> FM10K_DGLORTMAP_MASK_SHIFT))
> +		if (i == (~hw->mac.dglort_map >> FM10K_DGLORTMAP_MASK_SHIFT))

Strictly, only the if needs parentheses here, but I
think it reads better before this change.

> @@ -511,7 +511,7 @@ int fm10k_iov_configure(struct pci_dev *pdev, int num_vfs)
>  		return err;
>  
>  	/* allocate VFs if not already allocated */
> -	if (num_vfs && (num_vfs != current_vfs)) {
> +	if (num_vfs && num_vfs != current_vfs) {

RE: [net-next 2/7] fm10k: cleanup unnecessary parenthesis in fm10k_iov.c

[Keller, Jacob E]

> -----Original Message-----
> From: netdev-owner@vger.kernel.org [mailto:netdev-owner@vger.kernel.org]
> On Behalf Of Joe Perches
> Sent: Wednesday, January 31, 2018 3:35 AM
> To: Kirsher, Jeffrey T <jeffrey.t.kirsher@intel.com>; davem@davemloft.net
> Cc: Keller, Jacob E <jacob.e.keller@intel.com>; netdev@vger.kernel.org;
> nhorman@redhat.com; sassmann@redhat.com; jogreene@redhat.com
> Subject: Re: [net-next 2/7] fm10k: cleanup unnecessary parenthesis in
> fm10k_iov.c
> 
> On Wed, 2018-01-24 at 14:45 -0800, Jeff Kirsher wrote:
> > This fixes a few warnings found by checkpatch.pl --strict
> []
> > diff --git a/drivers/net/ethernet/intel/fm10k/fm10k_iov.c
> b/drivers/net/ethernet/intel/fm10k/fm10k_iov.c
> []
> > @@ -353,7 +353,7 @@ int fm10k_iov_resume(struct pci_dev *pdev)
> >  		struct fm10k_vf_info *vf_info = &iov_data->vf_info[i];
> >
> >  		/* allocate all but the last GLORT to the VFs */
> > -		if (i == ((~hw->mac.dglort_map) >>
> FM10K_DGLORTMAP_MASK_SHIFT))
> > +		if (i == (~hw->mac.dglort_map >>
> FM10K_DGLORTMAP_MASK_SHIFT))
> 
> Strictly, only the if needs parentheses here, but I
> think it reads better before this change.
> 

I don't really find the extra paranthesis around ~hw->mac.dglort_map to be that useful here.

Thanks,
Jake

> > @@ -511,7 +511,7 @@ int fm10k_iov_configure(struct pci_dev *pdev, int
> num_vfs)
> >  		return err;
> >
> >  	/* allocate VFs if not already allocated */
> > -	if (num_vfs && (num_vfs != current_vfs)) {
> > +	if (num_vfs && num_vfs != current_vfs) {
> 

[net-next 3/7] fm10k: fix "failed to kill vid" message for VF

[Jeff Kirsher]

From: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>

When a VF is under PF VLAN assignment:

ip link set <pf> vf <#> vlan <vid>

This will remove all previous entries in the VLAN table including those
generated by VLAN interfaces created on the VF. The issue arises when
the VF is under PF VLAN assignment and one or more of these VLAN
interfaces of the VF are deleted. When deleting these VLAN interfaces,
the following message will be generated in "dmesg":

failed to kill vid 0081/<vid> for device <vf>

This is due to the fact that "ndo_vlan_rx_kill_vid" exits with an error.
The handler for this ndo is "fm10k_update_vid". Any calls to this
function while under PF VLAN management will exit prematurely and, thus,
it will generate the failure message.

Additionally, since "fm10k_update_vid" exits prematurely, none of the
VLAN update is performed. So, even though the actual VLAN interfaces of
the VF will be deleted, the active_vlans bitmask is not cleared. When
the VF is no longer under PF VLAN assignment, the driver mistakenly
restores the previous entries of the VLAN table based on an
unsynchronized list of active VLANs.

The solution to this issue involves checking the VLAN update action type
before exiting "fm10k_update_vid". If the VLAN update action type is to
"add", this action will not be permitted while the VF is under PF VLAN
assignment and the VLAN update is abandoned like before.

However, if the VLAN update action type is to "kill", then we need to
also clear the active_vlans bitmask. However, we don't need to actually
queue any messages to the PF, because the MAC and VLAN tables have
already been cleared, and the PF would silently ignore these requests
anyways.

Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/fm10k/fm10k_netdev.c | 14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c b/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
index 6d9088956407..e85e0b077da3 100644
--- a/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
+++ b/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
@@ -934,8 +934,12 @@ static int fm10k_update_vid(struct net_device *netdev, u16 vid, bool set)
 	if (vid >= VLAN_N_VID)
 		return -EINVAL;
 
-	/* Verify we have permission to add VLANs */
-	if (hw->mac.vlan_override)
+	/* Verify that we have permission to add VLANs. If this is a request
+	 * to remove a VLAN, we still want to allow the user to remove the
+	 * VLAN device. In that case, we need to clear the bit in the
+	 * active_vlans bitmask.
+	 */
+	if (set && hw->mac.vlan_override)
 		return -EACCES;
 
 	/* update active_vlans bitmask */
@@ -954,6 +958,12 @@ static int fm10k_update_vid(struct net_device *netdev, u16 vid, bool set)
 			rx_ring->vid &= ~FM10K_VLAN_CLEAR;
 	}
 
+	/* If our VLAN has been overridden, there is no reason to send VLAN
+	 * removal requests as they will be silently ignored.
+	 */
+	if (hw->mac.vlan_override)
+		return 0;
+
 	/* Do not remove default VLAN ID related entries from VLAN and MAC
 	 * tables
 	 */
-- 
2.14.3

[net-next 4/7] fm10k: stop adding VLAN 0 to the VLAN table

[Jeff Kirsher]

From: Jacob Keller <jacob.e.keller@intel.com>

Currently, when the driver loads, it sends a request to add VLAN 0 to the
VLAN table. For the PF, this is honored, and VLAN 0 is indeed set. For
the VF, this request is silently converted into a request for the
default VLAN as defined by either the switch vid or the PF vid.

This results in the odd behavior that the VLAN table doesn't appear
consistent between the PF and the VF.

Furthermore, setting a MAC filter with VLAN 0 is generally considered an
invalid configuration by the switch, and since commit 856dfd69e84f
("fm10k: Fix multicast mode synch issues", 2016-03-03) we've had code
which prevents us from ever sending such a request.

Since there's not really a good reason to keep VLAN 0 in the VLAN table,
stop requesting it in fm10k_restore_rx_state().

This might seem to indicate that we would no longer properly configure
the MAC and VLAN tables for the default vid. However, due to the way
that fm10k_find_next_vlan() behaves, it will always return the
default_vid as enabled.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/fm10k/fm10k_netdev.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c b/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
index e85e0b077da3..4cf68a235318 100644
--- a/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
+++ b/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
@@ -1222,9 +1222,6 @@ void fm10k_restore_rx_state(struct fm10k_intfc *interface)
 	fm10k_queue_vlan_request(interface, FM10K_VLAN_ALL, 0,
 				 xcast_mode == FM10K_XCAST_MODE_PROMISC);
 
-	/* Add filter for VLAN 0 */
-	fm10k_queue_vlan_request(interface, 0, 0, true);
-
 	/* update table with current entries */
 	for (vid = hw->mac.default_vid ? fm10k_find_next_vlan(interface, 0) : 1;
 	     vid < VLAN_N_VID;
-- 
2.14.3

[net-next 5/7] fm10k: don't assume VLAN 1 is enabled

[Jeff Kirsher]

From: Jacob Keller <jacob.e.keller@intel.com>

Since commit 856dfd69e84f ("fm10k: Fix multicast mode synch issues",
2016-03-03) we've incorrectly assumed that VLAN 1 is enabled when the
default VID is not set.

This occurs because we check the default_vid and if it's zero, start
several loops over the active_vlans bitmask at 1, instead of checking to
ensure that that bit is active.

This happened because of commit d9ff3ee8efe9 ("fm10k: Add support for
VLAN 0 w/o default VLAN", 2014-08-07) which mistakenly assumed that we
should send requests for MAC and VLAN filters with VLAN 0 when the
default_vid isn't set.

However, the switch generally considers this an invalid configuration,
so the only time we'd have a default_vid of 0 is when the switch is
down.

Instead, lets just not request any filters for the default_vid if it's
not yet been assigned.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/fm10k/fm10k_netdev.c | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)

diff --git a/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c b/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
index 4cf68a235318..4c9d8e52415b 100644
--- a/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
+++ b/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
@@ -1050,14 +1050,13 @@ static int __fm10k_uc_sync(struct net_device *dev,
 			   const unsigned char *addr, bool sync)
 {
 	struct fm10k_intfc *interface = netdev_priv(dev);
-	struct fm10k_hw *hw = &interface->hw;
 	u16 vid, glort = interface->glort;
 	s32 err;
 
 	if (!is_valid_ether_addr(addr))
 		return -EADDRNOTAVAIL;
 
-	for (vid = hw->mac.default_vid ? fm10k_find_next_vlan(interface, 0) : 1;
+	for (vid = fm10k_find_next_vlan(interface, 0);
 	     vid < VLAN_N_VID;
 	     vid = fm10k_find_next_vlan(interface, vid)) {
 		err = fm10k_queue_mac_request(interface, glort,
@@ -1116,14 +1115,13 @@ static int __fm10k_mc_sync(struct net_device *dev,
 			   const unsigned char *addr, bool sync)
 {
 	struct fm10k_intfc *interface = netdev_priv(dev);
-	struct fm10k_hw *hw = &interface->hw;
 	u16 vid, glort = interface->glort;
 	s32 err;
 
 	if (!is_multicast_ether_addr(addr))
 		return -EADDRNOTAVAIL;
 
-	for (vid = hw->mac.default_vid ? fm10k_find_next_vlan(interface, 0) : 1;
+	for (vid = fm10k_find_next_vlan(interface, 0);
 	     vid < VLAN_N_VID;
 	     vid = fm10k_find_next_vlan(interface, vid)) {
 		err = fm10k_queue_mac_request(interface, glort,
@@ -1223,7 +1221,7 @@ void fm10k_restore_rx_state(struct fm10k_intfc *interface)
 				 xcast_mode == FM10K_XCAST_MODE_PROMISC);
 
 	/* update table with current entries */
-	for (vid = hw->mac.default_vid ? fm10k_find_next_vlan(interface, 0) : 1;
+	for (vid = fm10k_find_next_vlan(interface, 0);
 	     vid < VLAN_N_VID;
 	     vid = fm10k_find_next_vlan(interface, vid)) {
 		fm10k_queue_vlan_request(interface, vid, 0, true);
-- 
2.14.3

[net-next 6/7] fm10k: correct typo in fm10k_pf.c

[Jeff Kirsher]

From: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>

Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/fm10k/fm10k_pf.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/fm10k/fm10k_pf.c b/drivers/net/ethernet/intel/fm10k/fm10k_pf.c
index 425d814aed4d..d6406fc31ffb 100644
--- a/drivers/net/ethernet/intel/fm10k/fm10k_pf.c
+++ b/drivers/net/ethernet/intel/fm10k/fm10k_pf.c
@@ -866,7 +866,7 @@ static s32 fm10k_iov_assign_default_mac_vlan_pf(struct fm10k_hw *hw,
 	/* Determine correct default VLAN ID. The FM10K_VLAN_OVERRIDE bit is
 	 * used here to indicate to the VF that it will not have privilege to
 	 * write VLAN_TABLE. All policy is enforced on the PF but this allows
-	 * the VF to correctly report errors to userspace rqeuests.
+	 * the VF to correctly report errors to userspace requests.
 	 */
 	if (vf_info->pf_vid)
 		vf_vid = vf_info->pf_vid | FM10K_VLAN_OVERRIDE;
-- 
2.14.3

[net-next 7/7] fm10k: clarify action when updating the VLAN table

[Jeff Kirsher]

From: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>

Clarify the comment for when entering promiscuous mode that we update
the VLAN table. Add a comment distinguishing the case where we're
exiting promiscuous mode and need to clear the entire VLAN table.

Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@gmail.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/fm10k/fm10k_netdev.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c b/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
index 4c9d8e52415b..a38ae5c54da3 100644
--- a/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
+++ b/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
@@ -1165,10 +1165,12 @@ static void fm10k_set_rx_mode(struct net_device *dev)
 
 	/* update xcast mode first, but only if it changed */
 	if (interface->xcast_mode != xcast_mode) {
-		/* update VLAN table */
+		/* update VLAN table when entering promiscuous mode */
 		if (xcast_mode == FM10K_XCAST_MODE_PROMISC)
 			fm10k_queue_vlan_request(interface, FM10K_VLAN_ALL,
 						 0, true);
+
+		/* clear VLAN table when exiting promiscuous mode */
 		if (interface->xcast_mode == FM10K_XCAST_MODE_PROMISC)
 			fm10k_clear_unused_vlans(interface);
 
-- 
2.14.3

Re: [net-next 0/7][pull request] 100GbE Intel Wired LAN Driver Updates 2018-01-24

[David Miller]

From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Date: Wed, 24 Jan 2018 14:45:39 -0800

> This series contains updates to fm10k only.
> 
> Alex fixes MACVLAN offload for fm10k, where we were not seeing unicast
> packets being received because we did not correctly configure the
> default VLAN ID for the port and defaulting to 0.
> 
> Jake cleans up unnecessary parenthesis in a couple of "if" statements.
> Fixed the driver to stop adding VLAN 0 into the VLAN table, since it
> would cause the VLAN table to be inconsistent between the PF and VF.
> Also fixed an issue where we were assuming that VLAN 1 is enabled when
> the default VLAN ID is not set, so resolve by not requesting any filters
> for the default_vid if it has not yet been assigned.
> 
> Ngai fixes an issue which was generating a dmesg regarding unbale to
> kill a particular VLAN ID for the device.  This is due to
> ndo_vlan_rx_kill_vid() exits with an error and the handler for this ndo
> is fm10k_update_vid() which exits prematurely under PF VLAN management.
> So to resolve, we must check the VLAN update action type before exiting
> fm10k_update_vid(), and act appropriately based on the action type.
> Also corrected code comment typos.

Looks good, pulled, thanks Jeff.