From: Marc Kleine-Budde <mkl@pengutronix.de>
To: netdev@vger.kernel.org
Cc: davem@davemloft.net, linux-can@vger.kernel.org,
kernel@pengutronix.de,
"Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>,
linux-stable <stable@vger.kernel.org>,
"Marc Kleine-Budde" <mkl@pengutronix.de>
Subject: [PATCH 2/7] can: flexcan: fix endianess detection
Date: Tue, 8 May 2018 11:28:26 +0200 [thread overview]
Message-ID: <20180508092831.28247-3-mkl@pengutronix.de> (raw)
In-Reply-To: <20180508092831.28247-1-mkl@pengutronix.de>
From: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
In commit 88462d2a7830 ("can: flexcan: Remodel FlexCAN register r/w APIs
for big endian FlexCAN controllers.") the following logic was
implemented:
if the dt property "big-endian" is given or
the device is compatible to "fsl,p1010-flexcan":
use big-endian mode;
else
use little-endian mode;
This relies on commit d50f4630c2e1 ("arm: dts: Remove p1010-flexcan
compatible from imx series dts") which was applied a few commits later.
Without this commit (or an old device tree used for booting a new
kernel) the flexcan devices on i.MX25, i.MX28, i.MX35 and i.MX53 match
the 'the device is compatible to "fsl,p1010-flexcan"' test and so are
switched erroneously to big endian mode.
Instead of the check above put a quirk in devtype data and rely on
of_match_device yielding the most compatible match
Fixes: 88462d2a7830 ("can: flexcan: Remodel FlexCAN register r/w APIs for big endian FlexCAN controllers.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Gavin Schenk <g.schenk@eckelmann.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.16
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
---
drivers/net/can/flexcan.c | 26 ++++++++++++++------------
1 file changed, 14 insertions(+), 12 deletions(-)
diff --git a/drivers/net/can/flexcan.c b/drivers/net/can/flexcan.c
index 634c51e6b8ae..d53a45bf2a72 100644
--- a/drivers/net/can/flexcan.c
+++ b/drivers/net/can/flexcan.c
@@ -200,6 +200,7 @@
#define FLEXCAN_QUIRK_DISABLE_MECR BIT(4) /* Disable Memory error detection */
#define FLEXCAN_QUIRK_USE_OFF_TIMESTAMP BIT(5) /* Use timestamp based offloading */
#define FLEXCAN_QUIRK_BROKEN_PERR_STATE BIT(6) /* No interrupt for error passive */
+#define FLEXCAN_QUIRK_DEFAULT_BIG_ENDIAN BIT(7) /* default to BE register access */
/* Structure of the message buffer */
struct flexcan_mb {
@@ -287,6 +288,12 @@ struct flexcan_priv {
};
static const struct flexcan_devtype_data fsl_p1010_devtype_data = {
+ .quirks = FLEXCAN_QUIRK_BROKEN_WERR_STATE |
+ FLEXCAN_QUIRK_BROKEN_PERR_STATE |
+ FLEXCAN_QUIRK_DEFAULT_BIG_ENDIAN,
+};
+
+static const struct flexcan_devtype_data fsl_imx25_devtype_data = {
.quirks = FLEXCAN_QUIRK_BROKEN_WERR_STATE |
FLEXCAN_QUIRK_BROKEN_PERR_STATE,
};
@@ -1251,9 +1258,9 @@ static void unregister_flexcandev(struct net_device *dev)
static const struct of_device_id flexcan_of_match[] = {
{ .compatible = "fsl,imx6q-flexcan", .data = &fsl_imx6q_devtype_data, },
{ .compatible = "fsl,imx28-flexcan", .data = &fsl_imx28_devtype_data, },
- { .compatible = "fsl,imx53-flexcan", .data = &fsl_p1010_devtype_data, },
- { .compatible = "fsl,imx35-flexcan", .data = &fsl_p1010_devtype_data, },
- { .compatible = "fsl,imx25-flexcan", .data = &fsl_p1010_devtype_data, },
+ { .compatible = "fsl,imx53-flexcan", .data = &fsl_imx25_devtype_data, },
+ { .compatible = "fsl,imx35-flexcan", .data = &fsl_imx25_devtype_data, },
+ { .compatible = "fsl,imx25-flexcan", .data = &fsl_imx25_devtype_data, },
{ .compatible = "fsl,p1010-flexcan", .data = &fsl_p1010_devtype_data, },
{ .compatible = "fsl,vf610-flexcan", .data = &fsl_vf610_devtype_data, },
{ .compatible = "fsl,ls1021ar2-flexcan", .data = &fsl_ls1021a_r2_devtype_data, },
@@ -1337,18 +1344,13 @@ static int flexcan_probe(struct platform_device *pdev)
priv = netdev_priv(dev);
- if (of_property_read_bool(pdev->dev.of_node, "big-endian")) {
+ if (of_property_read_bool(pdev->dev.of_node, "big-endian") ||
+ devtype_data->quirks & FLEXCAN_QUIRK_DEFAULT_BIG_ENDIAN) {
priv->read = flexcan_read_be;
priv->write = flexcan_write_be;
} else {
- if (of_device_is_compatible(pdev->dev.of_node,
- "fsl,p1010-flexcan")) {
- priv->read = flexcan_read_be;
- priv->write = flexcan_write_be;
- } else {
- priv->read = flexcan_read_le;
- priv->write = flexcan_write_le;
- }
+ priv->read = flexcan_read_le;
+ priv->write = flexcan_write_le;
}
priv->can.clock.freq = clock_freq;
--
2.17.0
next prev parent reply other threads:[~2018-05-08 9:28 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-08 9:28 pull-request: can 2018-05-08 Marc Kleine-Budde
2018-05-08 9:28 ` [PATCH 1/7] can: dev: increase bus-off message severity Marc Kleine-Budde
2018-05-08 9:28 ` Marc Kleine-Budde [this message]
2018-05-08 9:28 ` [PATCH 3/7] arm: dts: imx[35]*: declare flexcan devices to be compatible to imx25's flexcan Marc Kleine-Budde
2018-05-08 9:28 ` [PATCH 4/7] can: kvaser_usb: Increase correct stats counter in kvaser_usb_rx_can_msg() Marc Kleine-Budde
2018-05-08 9:28 ` [PATCH 5/7] dt-bindings: can: rcar_can: Fix R8A7796 SoC name Marc Kleine-Budde
2018-05-08 9:28 ` [PATCH 6/7] DT: net: can: rcar_canfd: document R8A77970 bindings Marc Kleine-Budde
2018-05-08 9:28 ` [PATCH 7/7] DT: net: can: rcar_canfd: document R8A77980 bindings Marc Kleine-Budde
2018-05-08 14:20 ` pull-request: can 2018-05-08 David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180508092831.28247-3-mkl@pengutronix.de \
--to=mkl@pengutronix.de \
--cc=davem@davemloft.net \
--cc=kernel@pengutronix.de \
--cc=linux-can@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=stable@vger.kernel.org \
--cc=u.kleine-koenig@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).