Re: [patch net-next RFC 04/12] dsa: set devlink port attrs for dsa ports

[Andrew Lunn <andrew@lunn.ch>]

On Thu, May 17, 2018 at 03:06:36PM -0700, Florian Fainelli wrote:
> On 05/17/2018 02:08 PM, Andrew Lunn wrote:
> > On Thu, May 17, 2018 at 10:48:55PM +0200, Jiri Pirko wrote:
> >> Thu, May 17, 2018 at 09:14:32PM CEST, f.fainelli@gmail.com wrote:
> >>> On 05/17/2018 10:39 AM, Jiri Pirko wrote:
> >>>>>> That is compiled inside "fixed_phy", isn't it?
> >>>>>
> >>>>> It matches what CONFIG_FIXED_PHY is, so if it's built-in it also becomes
> >>>>> built-in, if is modular, it is also modular, this was fixed with
> >>>>> 40013ff20b1beed31184935fc0aea6a859d4d4ef ("net: dsa: Fix functional
> >>>>> dsa-loop dependency on FIXED_PHY")
> >>>>
> >>>> Now I have it compiled as module, and after modprobe dsa_loop I see:
> >>>> [ 1168.129202] libphy: Fixed MDIO Bus: probed
> >>>> [ 1168.222716] dsa-loop fixed-0:1f: DSA mockup driver: 0x1f
> >>>>
> >>>> This messages I did not see when I had fixed_phy compiled as buildin.
> >>>>
> >>>> But I still see no netdevs :/
> >>>
> >>> The platform data assumes there is a network device named "eth0" as the
> >>
> >> Oups, I missed, I created dummy device and modprobed again. Now I see:
> >>
> >> $ sudo devlink port
> >> mdio_bus/fixed-0:1f/0: type eth netdev lan1
> >> mdio_bus/fixed-0:1f/1: type eth netdev lan2
> >> mdio_bus/fixed-0:1f/2: type eth netdev lan3
> >> mdio_bus/fixed-0:1f/3: type eth netdev lan4
> >> mdio_bus/fixed-0:1f/4: type notset
> >> mdio_bus/fixed-0:1f/5: type notset
> >> mdio_bus/fixed-0:1f/6: type notset
> >> mdio_bus/fixed-0:1f/7: type notset
> >> mdio_bus/fixed-0:1f/8: type notset
> >> mdio_bus/fixed-0:1f/9: type notset
> >> mdio_bus/fixed-0:1f/10: type notset
> >> mdio_bus/fixed-0:1f/11: type notset
> >>
> >> I wonder why there are ports 4-11
> > 
> > Hi Jiri
> > 
> >         ds = dsa_switch_alloc(&mdiodev->dev, DSA_MAX_PORTS);
> > 
> > It is allocating a switch with 12 ports. However only 4 of them have
> > names. So the core only creates slave devices for those 4.
> > 
> > This is a useful test. Real hardware often has unused ports. A WiFi AP
> > with a 7 port switch which only uses 6 ports is often seen.
> 
> The following patch should fix this:
> 
> 
> diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
> index adf50fbc4c13..a06c29ec91f0 100644
> --- a/net/dsa/dsa2.c
> +++ b/net/dsa/dsa2.c
> @@ -262,13 +262,14 @@ static int dsa_port_setup(struct dsa_port *dp)
> 
>         memset(&dp->devlink_port, 0, sizeof(dp->devlink_port));
> 
> +       if (dp->type == DSA_PORT_TYPE_UNUSED)
> +               return 0;
> +
>         err = devlink_port_register(ds->devlink, &dp->devlink_port,
> dp->index);

Hi Florian, Jiri

Maybe it is better to add a devlink port type unused?

      Andrew