Re: [PATCH net-next 07/10] r8169: migrate speed_down function to phylib

[Andrew Lunn <andrew@lunn.ch>]

 On Mon, Jul 02, 2018 at 09:37:08PM +0200, Heiner Kallweit wrote:
> Change rtl_speed_down() to use phylib.
> 
> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
> ---
>  drivers/net/ethernet/realtek/r8169.c | 33 +++++++++++++---------------
>  1 file changed, 15 insertions(+), 18 deletions(-)
> 
> diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c
> index 311321ee..807fbc75 100644
> --- a/drivers/net/ethernet/realtek/r8169.c
> +++ b/drivers/net/ethernet/realtek/r8169.c
> @@ -4240,6 +4240,10 @@ static void rtl8169_init_phy(struct net_device *dev, struct rtl8169_private *tp)
>  		rtl_writephy(tp, 0x0b, 0x0000); //w 0x0b 15 0 0
>  	}
>  
> +	/* We may have called rtl_speed_down before */
> +	dev->phydev->advertising = dev->phydev->supported;
> +	genphy_config_aneg(dev->phydev);
> +
>  	genphy_soft_reset(dev->phydev);
>  
>  	rtl8169_set_speed(dev, AUTONEG_ENABLE, SPEED_1000, DUPLEX_FULL,
> @@ -4323,28 +4327,21 @@ static void rtl_init_mdio_ops(struct rtl8169_private *tp)
>  	}
>  }
>  
> +#define BASET10		(ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full)
> +#define BASET100	(ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full)
> +#define BASET1000	(ADVERTISED_1000baseT_Half | ADVERTISED_1000baseT_Full)
> +
>  static void rtl_speed_down(struct rtl8169_private *tp)
>  {
> -	u32 adv;
> -	int lpa;
> +	struct phy_device *phydev = tp->dev->phydev;
> +	u32 adv = phydev->lp_advertising & phydev->supported;
>  
> -	rtl_writephy(tp, 0x1f, 0x0000);
> -	lpa = rtl_readphy(tp, MII_LPA);
> +	if (adv & BASET10)
> +		phydev->advertising &= ~(BASET100 | BASET1000);
> +	else if (adv & BASET100)
> +		phydev->advertising &= ~BASET1000;
>  
> -	if (lpa & (LPA_10HALF | LPA_10FULL))
> -		adv = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full;
> -	else if (lpa & (LPA_100HALF | LPA_100FULL))
> -		adv = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full |
> -		      ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full;
> -	else
> -		adv = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full |
> -		      ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full |
> -		      (tp->mii.supports_gmii ?
> -		       ADVERTISED_1000baseT_Half |
> -		       ADVERTISED_1000baseT_Full : 0);
> -
> -	rtl8169_set_speed(tp->dev, AUTONEG_ENABLE, SPEED_1000, DUPLEX_FULL,
> -			  adv);
> +	genphy_config_aneg(phydev);
>  }

It probably it is me being too tired, but i don't get what this is
doing? Changing the local advertisement based on what the remote is
advertising. Why?

	Andrew