From mboxrd@z Thu Jan 1 00:00:00 1970 From: Linus Walleij Subject: [PATCH 4/4 v1] ARM: dts: Add ethernet and switch to D-Link DIR-685 Date: Sat, 14 Jul 2018 11:45:56 +0200 Message-ID: <20180714094556.30791-4-linus.walleij@linaro.org> References: <20180714094556.30791-1-linus.walleij@linaro.org> Cc: netdev@vger.kernel.org, openwrt-devel@lists.openwrt.org, LEDE Development List , Linus Walleij To: Andrew Lunn , Vivien Didelot , Florian Fainelli Return-path: Received: from mail-lj1-f193.google.com ([209.85.208.193]:37064 "EHLO mail-lj1-f193.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728171AbeGNKGy (ORCPT ); Sat, 14 Jul 2018 06:06:54 -0400 Received: by mail-lj1-f193.google.com with SMTP id v9-v6so15886429ljk.4 for ; Sat, 14 Jul 2018 02:48:21 -0700 (PDT) In-Reply-To: <20180714094556.30791-1-linus.walleij@linaro.org> Sender: netdev-owner@vger.kernel.org List-ID: This adds the Ethernet and Realtek switch device to the D-Link DIR-685 Gemini-based device. Signed-off-by: Linus Walleij --- ChangeLog RFCv2->v1 - Use a fixed link on the ethernet port towards the router chip. ChangeLog RFCv1->RFCv2 - Rebased, use the new DT bindings --- arch/arm/boot/dts/gemini-dlink-dir-685.dts | 140 ++++++++++++++++++++- 1 file changed, 139 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/gemini-dlink-dir-685.dts b/arch/arm/boot/dts/gemini-dlink-dir-685.dts index fb5c954ab95a..6f258b50eb44 100644 --- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts +++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts @@ -156,6 +156,100 @@ }; }; + /* This is a RealTek RTL8366RB switch and PHY using SMI over GPIO */ + switch { + compatible = "realtek,rtl8366rb"; + /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ + mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + realtek,disable-leds; + + switch_intc: interrupt-controller { + /* GPIO 15 provides the interrupt */ + interrupt-parent = <&gpio0>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + phy-handle = <&phy0>; + }; + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy1>; + }; + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy2>; + }; + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy3>; + }; + port@4 { + reg = <4>; + label = "wan"; + phy-handle = <&phy4>; + }; + rtl8366rb_cpu_port: port@5 { + reg = <5>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + + }; + + mdio { + compatible = "realtek,smi-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + phy0: phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc>; + interrupts = <0>; + }; + phy1: phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc>; + interrupts = <1>; + }; + phy2: phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc>; + interrupts = <2>; + }; + phy3: phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc>; + interrupts = <3>; + }; + phy4: phy@4 { + reg = <4>; + interrupt-parent = <&switch_intc>; + interrupts = <12>; + }; + }; + }; + soc { flash@30000000 { /* @@ -223,10 +317,12 @@ * gpio0bgrp cover line 7 used by WPS LED * gpio0cgrp cover line 8, 13 used by keys * and 11, 12 used by the HD LEDs + * and line 14, 15 used by RTL8366 + * RESET and phy ready * gpio0egrp cover line 16 used by VDISP * gpio0fgrp cover line 17 used by TK IRQ * gpio0ggrp cover line 20 used by panel CS - * gpio0hgrp cover line 21,22 used by RTL8366RB + * gpio0hgrp cover line 21,22 used by RTL8366RB MDIO */ gpio0_default_pins: pinctrl-gpio0 { mux { @@ -250,6 +346,32 @@ groups = "gpio1bgrp"; }; }; + pinctrl-gmii { + mux { + function = "gmii"; + groups = "gmii_gmac0_grp"; + }; + conf0 { + pins = "V8 GMAC0 RXDV", "T10 GMAC1 RXDV", + "Y7 GMAC0 RXC", "Y11 GMAC1 RXC", + "T8 GMAC0 TXEN", "W11 GMAC1 TXEN", + "U8 GMAC0 TXC", "V11 GMAC1 TXC", + "W8 GMAC0 RXD0", "V9 GMAC0 RXD1", + "Y8 GMAC0 RXD2", "U9 GMAC0 RXD3", + "T7 GMAC0 TXD0", "U6 GMAC0 TXD1", + "V7 GMAC0 TXD2", "U7 GMAC0 TXD3", + "Y12 GMAC1 RXD0", "V12 GMAC1 RXD1", + "T11 GMAC1 RXD2", "W12 GMAC1 RXD3", + "U10 GMAC1 TXD0", "Y10 GMAC1 TXD1", + "W10 GMAC1 TXD2", "T9 GMAC1 TXD3"; + skew-delay = <7>; + }; + /* Set up drive strength on GMAC0 to 16 mA */ + conf1 { + groups = "gmii_gmac0_grp"; + drive-strength = <16>; + }; + }; }; }; @@ -291,6 +413,22 @@ <0x6000 0 0 4 &pci_intc 2>; }; + ethernet@60000000 { + status = "okay"; + + ethernet-port@0 { + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + ethernet-port@1 { + /* Not used in this platform */ + }; + }; + ata@63000000 { status = "okay"; }; -- 2.17.1