* [PATCH v3 net-next 2/6] net: dsa: Add Lantiq / Intel GSWIP tag support
2018-09-09 20:16 [PATCH v3 net-next 0/6] Add support for Lantiq / Intel vrx200 network Hauke Mehrtens
2018-09-09 20:16 ` [PATCH v3 net-next 1/6] MIPS: lantiq: Do not enable IRQs in dma open Hauke Mehrtens
@ 2018-09-09 20:16 ` Hauke Mehrtens
2018-09-09 20:16 ` [PATCH v3 net-next 3/6] dt-bindings: net: Add lantiq,xrx200-net DT bindings Hauke Mehrtens
` (2 subsequent siblings)
4 siblings, 0 replies; 9+ messages in thread
From: Hauke Mehrtens @ 2018-09-09 20:16 UTC (permalink / raw)
To: davem
Cc: netdev, andrew, vivien.didelot, f.fainelli, john, linux-mips, dev,
hauke.mehrtens, devicetree, Hauke Mehrtens
This handles the tag added by the PMAC on the VRX200 SoC line.
The GSWIP uses internally a GSWIP special tag which is located after the
Ethernet header. The PMAC which connects the GSWIP to the CPU converts
this special tag used by the GSWIP into the PMAC special tag which is
added in front of the Ethernet header.
This was tested with GSWIP 2.1 found in the VRX200 SoCs, other GSWIP
versions use slightly different PMAC special tags.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
MAINTAINERS | 6 +++
include/net/dsa.h | 1 +
net/dsa/Kconfig | 3 ++
net/dsa/Makefile | 1 +
net/dsa/dsa.c | 3 ++
net/dsa/dsa_priv.h | 3 ++
net/dsa/tag_gswip.c | 109 ++++++++++++++++++++++++++++++++++++++++++++++++++++
7 files changed, 126 insertions(+)
create mode 100644 net/dsa/tag_gswip.c
diff --git a/MAINTAINERS b/MAINTAINERS
index a5b256b25905..4b2ee65f6086 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8166,6 +8166,12 @@ S: Maintained
F: net/l3mdev
F: include/net/l3mdev.h
+LANTIQ / INTEL Ethernet drivers
+M: Hauke Mehrtens <hauke@hauke-m.de>
+L: netdev@vger.kernel.org
+S: Maintained
+F: net/dsa/tag_gswip.c
+
LANTIQ MIPS ARCHITECTURE
M: John Crispin <john@phrozen.org>
L: linux-mips@linux-mips.org
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 461e8a7661b7..23690c44e167 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -35,6 +35,7 @@ enum dsa_tag_protocol {
DSA_TAG_PROTO_BRCM_PREPEND,
DSA_TAG_PROTO_DSA,
DSA_TAG_PROTO_EDSA,
+ DSA_TAG_PROTO_GSWIP,
DSA_TAG_PROTO_KSZ,
DSA_TAG_PROTO_LAN9303,
DSA_TAG_PROTO_MTK,
diff --git a/net/dsa/Kconfig b/net/dsa/Kconfig
index 4183e4ba27a5..48c41918fb35 100644
--- a/net/dsa/Kconfig
+++ b/net/dsa/Kconfig
@@ -38,6 +38,9 @@ config NET_DSA_TAG_DSA
config NET_DSA_TAG_EDSA
bool
+config NET_DSA_TAG_GSWIP
+ bool
+
config NET_DSA_TAG_KSZ
bool
diff --git a/net/dsa/Makefile b/net/dsa/Makefile
index 9e4d3536f977..6e721f7a2947 100644
--- a/net/dsa/Makefile
+++ b/net/dsa/Makefile
@@ -9,6 +9,7 @@ dsa_core-$(CONFIG_NET_DSA_TAG_BRCM) += tag_brcm.o
dsa_core-$(CONFIG_NET_DSA_TAG_BRCM_PREPEND) += tag_brcm.o
dsa_core-$(CONFIG_NET_DSA_TAG_DSA) += tag_dsa.o
dsa_core-$(CONFIG_NET_DSA_TAG_EDSA) += tag_edsa.o
+dsa_core-$(CONFIG_NET_DSA_TAG_GSWIP) += tag_gswip.o
dsa_core-$(CONFIG_NET_DSA_TAG_KSZ) += tag_ksz.o
dsa_core-$(CONFIG_NET_DSA_TAG_LAN9303) += tag_lan9303.o
dsa_core-$(CONFIG_NET_DSA_TAG_MTK) += tag_mtk.o
diff --git a/net/dsa/dsa.c b/net/dsa/dsa.c
index e63c554e0623..81212109c507 100644
--- a/net/dsa/dsa.c
+++ b/net/dsa/dsa.c
@@ -54,6 +54,9 @@ const struct dsa_device_ops *dsa_device_ops[DSA_TAG_LAST] = {
#ifdef CONFIG_NET_DSA_TAG_EDSA
[DSA_TAG_PROTO_EDSA] = &edsa_netdev_ops,
#endif
+#ifdef CONFIG_NET_DSA_TAG_GSWIP
+ [DSA_TAG_PROTO_GSWIP] = &gswip_netdev_ops,
+#endif
#ifdef CONFIG_NET_DSA_TAG_KSZ
[DSA_TAG_PROTO_KSZ] = &ksz_netdev_ops,
#endif
diff --git a/net/dsa/dsa_priv.h b/net/dsa/dsa_priv.h
index 3964c6f7a7c0..824ca07a30aa 100644
--- a/net/dsa/dsa_priv.h
+++ b/net/dsa/dsa_priv.h
@@ -205,6 +205,9 @@ extern const struct dsa_device_ops dsa_netdev_ops;
/* tag_edsa.c */
extern const struct dsa_device_ops edsa_netdev_ops;
+/* tag_gswip.c */
+extern const struct dsa_device_ops gswip_netdev_ops;
+
/* tag_ksz.c */
extern const struct dsa_device_ops ksz_netdev_ops;
diff --git a/net/dsa/tag_gswip.c b/net/dsa/tag_gswip.c
new file mode 100644
index 000000000000..49e9b73f1be3
--- /dev/null
+++ b/net/dsa/tag_gswip.c
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Intel / Lantiq GSWIP V2.0 PMAC tag support
+ *
+ * Copyright (C) 2017 - 2018 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+#include <linux/bitops.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <net/dsa.h>
+
+#include "dsa_priv.h"
+
+#define GSWIP_TX_HEADER_LEN 4
+
+/* special tag in TX path header */
+/* Byte 0 */
+#define GSWIP_TX_SLPID_SHIFT 0 /* source port ID */
+#define GSWIP_TX_SLPID_CPU 2
+#define GSWIP_TX_SLPID_APP1 3
+#define GSWIP_TX_SLPID_APP2 4
+#define GSWIP_TX_SLPID_APP3 5
+#define GSWIP_TX_SLPID_APP4 6
+#define GSWIP_TX_SLPID_APP5 7
+
+/* Byte 1 */
+#define GSWIP_TX_CRCGEN_DIS BIT(7)
+#define GSWIP_TX_DPID_SHIFT 0 /* destination group ID */
+#define GSWIP_TX_DPID_ELAN 0
+#define GSWIP_TX_DPID_EWAN 1
+#define GSWIP_TX_DPID_CPU 2
+#define GSWIP_TX_DPID_APP1 3
+#define GSWIP_TX_DPID_APP2 4
+#define GSWIP_TX_DPID_APP3 5
+#define GSWIP_TX_DPID_APP4 6
+#define GSWIP_TX_DPID_APP5 7
+
+/* Byte 2 */
+#define GSWIP_TX_PORT_MAP_EN BIT(7)
+#define GSWIP_TX_PORT_MAP_SEL BIT(6)
+#define GSWIP_TX_LRN_DIS BIT(5)
+#define GSWIP_TX_CLASS_EN BIT(4)
+#define GSWIP_TX_CLASS_SHIFT 0
+#define GSWIP_TX_CLASS_MASK GENMASK(3, 0)
+
+/* Byte 3 */
+#define GSWIP_TX_DPID_EN BIT(0)
+#define GSWIP_TX_PORT_MAP_SHIFT 1
+#define GSWIP_TX_PORT_MAP_MASK GENMASK(6, 1)
+
+#define GSWIP_RX_HEADER_LEN 8
+
+/* special tag in RX path header */
+/* Byte 7 */
+#define GSWIP_RX_SPPID_SHIFT 4
+#define GSWIP_RX_SPPID_MASK GENMASK(6, 4)
+
+static struct sk_buff *gswip_tag_xmit(struct sk_buff *skb,
+ struct net_device *dev)
+{
+ struct dsa_port *dp = dsa_slave_to_port(dev);
+ int err;
+ u8 *gswip_tag;
+
+ err = skb_cow_head(skb, GSWIP_TX_HEADER_LEN);
+ if (err)
+ return NULL;
+
+ skb_push(skb, GSWIP_TX_HEADER_LEN);
+
+ gswip_tag = skb->data;
+ gswip_tag[0] = GSWIP_TX_SLPID_CPU;
+ gswip_tag[1] = GSWIP_TX_DPID_ELAN;
+ gswip_tag[2] = GSWIP_TX_PORT_MAP_EN | GSWIP_TX_PORT_MAP_SEL;
+ gswip_tag[3] = BIT(dp->index + GSWIP_TX_PORT_MAP_SHIFT) & GSWIP_TX_PORT_MAP_MASK;
+ gswip_tag[3] |= GSWIP_TX_DPID_EN;
+
+ return skb;
+}
+
+static struct sk_buff *gswip_tag_rcv(struct sk_buff *skb,
+ struct net_device *dev,
+ struct packet_type *pt)
+{
+ int port;
+ u8 *gswip_tag;
+
+ if (unlikely(!pskb_may_pull(skb, GSWIP_RX_HEADER_LEN)))
+ return NULL;
+
+ gswip_tag = skb->data - ETH_HLEN;
+
+ /* Get source port information */
+ port = (gswip_tag[7] & GSWIP_RX_SPPID_MASK) >> GSWIP_RX_SPPID_SHIFT;
+ skb->dev = dsa_master_find_slave(dev, 0, port);
+ if (!skb->dev)
+ return NULL;
+
+ /* remove GSWIP tag */
+ skb_pull_rcsum(skb, GSWIP_RX_HEADER_LEN);
+
+ return skb;
+}
+
+const struct dsa_device_ops gswip_netdev_ops = {
+ .xmit = gswip_tag_xmit,
+ .rcv = gswip_tag_rcv,
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH v3 net-next 4/6] net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver
2018-09-09 20:16 [PATCH v3 net-next 0/6] Add support for Lantiq / Intel vrx200 network Hauke Mehrtens
` (2 preceding siblings ...)
2018-09-09 20:16 ` [PATCH v3 net-next 3/6] dt-bindings: net: Add lantiq,xrx200-net DT bindings Hauke Mehrtens
@ 2018-09-09 20:16 ` Hauke Mehrtens
2018-09-13 15:15 ` [PATCH v3 net-next 0/6] Add support for Lantiq / Intel vrx200 network David Miller
4 siblings, 0 replies; 9+ messages in thread
From: Hauke Mehrtens @ 2018-09-09 20:16 UTC (permalink / raw)
To: davem
Cc: netdev, andrew, vivien.didelot, f.fainelli, john, linux-mips, dev,
hauke.mehrtens, devicetree, Hauke Mehrtens
This drives the PMAC between the GSWIP Switch and the CPU in the VRX200
SoC. This is currently only the very basic version of the Ethernet
driver.
When the DMA channel is activated we receive some packets which were
send to the SoC while it was still in U-Boot, these packets have the
wrong header. Resetting the IP cores did not work so we read out the
extra packets at the beginning and discard them.
This also adapts the clock code in sysctrl.c to use the default name of
the device node so that the driver gets the correct clock. sysctrl.c
should be replaced with a proper common clock driver later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
---
MAINTAINERS | 1 +
arch/mips/lantiq/xway/sysctrl.c | 6 +-
drivers/net/ethernet/Kconfig | 7 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/lantiq_xrx200.c | 564 +++++++++++++++++++++++++++++++++++
5 files changed, 576 insertions(+), 3 deletions(-)
create mode 100644 drivers/net/ethernet/lantiq_xrx200.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 4b2ee65f6086..ffff912d31b5 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8171,6 +8171,7 @@ M: Hauke Mehrtens <hauke@hauke-m.de>
L: netdev@vger.kernel.org
S: Maintained
F: net/dsa/tag_gswip.c
+F: drivers/net/ethernet/lantiq_xrx200.c
LANTIQ MIPS ARCHITECTURE
M: John Crispin <john@phrozen.org>
diff --git a/arch/mips/lantiq/xway/sysctrl.c b/arch/mips/lantiq/xway/sysctrl.c
index e0af39b33e28..eeb89a37e27e 100644
--- a/arch/mips/lantiq/xway/sysctrl.c
+++ b/arch/mips/lantiq/xway/sysctrl.c
@@ -505,7 +505,7 @@ void __init ltq_soc_init(void)
clkdev_add_pmu("1a800000.pcie", "msi", 1, 1, PMU1_PCIE2_MSI);
clkdev_add_pmu("1a800000.pcie", "pdi", 1, 1, PMU1_PCIE2_PDI);
clkdev_add_pmu("1a800000.pcie", "ctl", 1, 1, PMU1_PCIE2_CTL);
- clkdev_add_pmu("1e108000.eth", NULL, 0, 0, PMU_SWITCH | PMU_PPE_DP);
+ clkdev_add_pmu("1e10b308.eth", NULL, 0, 0, PMU_SWITCH | PMU_PPE_DP);
clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
} else if (of_machine_is_compatible("lantiq,ar10")) {
@@ -513,7 +513,7 @@ void __init ltq_soc_init(void)
ltq_ar10_fpi_hz(), ltq_ar10_pp32_hz());
clkdev_add_pmu("1e101000.usb", "otg", 1, 0, PMU_USB0);
clkdev_add_pmu("1e106000.usb", "otg", 1, 0, PMU_USB1);
- clkdev_add_pmu("1e108000.eth", NULL, 0, 0, PMU_SWITCH |
+ clkdev_add_pmu("1e10b308.eth", NULL, 0, 0, PMU_SWITCH |
PMU_PPE_DP | PMU_PPE_TC);
clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
clkdev_add_pmu("1f203020.gphy", NULL, 1, 0, PMU_GPHY);
@@ -536,7 +536,7 @@ void __init ltq_soc_init(void)
clkdev_add_pmu(NULL, "ahb", 1, 0, PMU_AHBM | PMU_AHBS);
clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
- clkdev_add_pmu("1e108000.eth", NULL, 0, 0,
+ clkdev_add_pmu("1e10b308.eth", NULL, 0, 0,
PMU_SWITCH | PMU_PPE_DPLUS | PMU_PPE_DPLUM |
PMU_PPE_EMA | PMU_PPE_TC | PMU_PPE_SLL01 |
PMU_PPE_QSB | PMU_PPE_TOP);
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 6fde68aa13a4..885e00d17807 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -108,6 +108,13 @@ config LANTIQ_ETOP
---help---
Support for the MII0 inside the Lantiq SoC
+config LANTIQ_XRX200
+ tristate "Lantiq / Intel xRX200 PMAC network driver"
+ depends on SOC_TYPE_XWAY
+ ---help---
+ Support for the PMAC of the Gigabit switch (GSWIP) inside the
+ Lantiq / Intel VRX200 VDSL SoC
+
source "drivers/net/ethernet/marvell/Kconfig"
source "drivers/net/ethernet/mediatek/Kconfig"
source "drivers/net/ethernet/mellanox/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index b45d5f626b59..7b5bf9682066 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -49,6 +49,7 @@ obj-$(CONFIG_NET_VENDOR_XSCALE) += xscale/
obj-$(CONFIG_JME) += jme.o
obj-$(CONFIG_KORINA) += korina.o
obj-$(CONFIG_LANTIQ_ETOP) += lantiq_etop.o
+obj-$(CONFIG_LANTIQ_XRX200) += lantiq_xrx200.o
obj-$(CONFIG_NET_VENDOR_MARVELL) += marvell/
obj-$(CONFIG_NET_VENDOR_MEDIATEK) += mediatek/
obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
diff --git a/drivers/net/ethernet/lantiq_xrx200.c b/drivers/net/ethernet/lantiq_xrx200.c
new file mode 100644
index 000000000000..c8b6d908f0cc
--- /dev/null
+++ b/drivers/net/ethernet/lantiq_xrx200.c
@@ -0,0 +1,564 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Lantiq / Intel PMAC driver for XRX200 SoCs
+ *
+ * Copyright (C) 2010 Lantiq Deutschland
+ * Copyright (C) 2012 John Crispin <john@phrozen.org>
+ * Copyright (C) 2017 - 2018 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+
+#include <xway_dma.h>
+
+/* DMA */
+#define XRX200_DMA_DATA_LEN 0x600
+#define XRX200_DMA_RX 0
+#define XRX200_DMA_TX 1
+
+/* cpu port mac */
+#define PMAC_RX_IPG 0x0024
+#define PMAC_RX_IPG_MASK 0xf
+
+#define PMAC_HD_CTL 0x0000
+/* Add Ethernet header to packets from DMA to PMAC */
+#define PMAC_HD_CTL_ADD BIT(0)
+/* Add VLAN tag to Packets from DMA to PMAC */
+#define PMAC_HD_CTL_TAG BIT(1)
+/* Add CRC to packets from DMA to PMAC */
+#define PMAC_HD_CTL_AC BIT(2)
+/* Add status header to packets from PMAC to DMA */
+#define PMAC_HD_CTL_AS BIT(3)
+/* Remove CRC from packets from PMAC to DMA */
+#define PMAC_HD_CTL_RC BIT(4)
+/* Remove Layer-2 header from packets from PMAC to DMA */
+#define PMAC_HD_CTL_RL2 BIT(5)
+/* Status header is present from DMA to PMAC */
+#define PMAC_HD_CTL_RXSH BIT(6)
+/* Add special tag from PMAC to switch */
+#define PMAC_HD_CTL_AST BIT(7)
+/* Remove specail Tag from PMAC to DMA */
+#define PMAC_HD_CTL_RST BIT(8)
+/* Check CRC from DMA to PMAC */
+#define PMAC_HD_CTL_CCRC BIT(9)
+/* Enable reaction to Pause frames in the PMAC */
+#define PMAC_HD_CTL_FC BIT(10)
+
+struct xrx200_chan {
+ int tx_free;
+
+ struct napi_struct napi;
+ struct ltq_dma_channel dma;
+ struct sk_buff *skb[LTQ_DESC_NUM];
+
+ struct xrx200_priv *priv;
+};
+
+struct xrx200_priv {
+ struct clk *clk;
+
+ struct xrx200_chan chan_tx;
+ struct xrx200_chan chan_rx;
+
+ struct net_device *net_dev;
+ struct device *dev;
+
+ __iomem void *pmac_reg;
+};
+
+static u32 xrx200_pmac_r32(struct xrx200_priv *priv, u32 offset)
+{
+ return __raw_readl(priv->pmac_reg + offset);
+}
+
+static void xrx200_pmac_w32(struct xrx200_priv *priv, u32 val, u32 offset)
+{
+ __raw_writel(val, priv->pmac_reg + offset);
+}
+
+static void xrx200_pmac_mask(struct xrx200_priv *priv, u32 clear, u32 set,
+ u32 offset)
+{
+ u32 val = xrx200_pmac_r32(priv, offset);
+
+ val &= ~(clear);
+ val |= set;
+ xrx200_pmac_w32(priv, val, offset);
+}
+
+/* drop all the packets from the DMA ring */
+static void xrx200_flush_dma(struct xrx200_chan *ch)
+{
+ int i;
+
+ for (i = 0; i < LTQ_DESC_NUM; i++) {
+ struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc];
+
+ if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) != LTQ_DMA_C)
+ break;
+
+ desc->ctl = LTQ_DMA_OWN | LTQ_DMA_RX_OFFSET(NET_IP_ALIGN) |
+ XRX200_DMA_DATA_LEN;
+ ch->dma.desc++;
+ ch->dma.desc %= LTQ_DESC_NUM;
+ }
+}
+
+static int xrx200_open(struct net_device *net_dev)
+{
+ struct xrx200_priv *priv = netdev_priv(net_dev);
+ int err;
+
+ /* enable clock gate */
+ err = clk_prepare_enable(priv->clk);
+ if (err)
+ return err;
+
+ napi_enable(&priv->chan_tx.napi);
+ ltq_dma_open(&priv->chan_tx.dma);
+ ltq_dma_enable_irq(&priv->chan_tx.dma);
+
+ napi_enable(&priv->chan_rx.napi);
+ ltq_dma_open(&priv->chan_rx.dma);
+ /* The boot loader does not always deactivate the receiving of frames
+ * on the ports and then some packets queue up in the PPE buffers.
+ * They already passed the PMAC so they do not have the tags
+ * configured here. Read the these packets here and drop them.
+ * The HW should have written them into memory after 10us
+ */
+ usleep_range(20, 40);
+ xrx200_flush_dma(&priv->chan_rx);
+ ltq_dma_enable_irq(&priv->chan_rx.dma);
+
+ netif_wake_queue(net_dev);
+
+ return 0;
+}
+
+static int xrx200_close(struct net_device *net_dev)
+{
+ struct xrx200_priv *priv = netdev_priv(net_dev);
+
+ netif_stop_queue(net_dev);
+
+ napi_disable(&priv->chan_rx.napi);
+ ltq_dma_close(&priv->chan_rx.dma);
+
+ napi_disable(&priv->chan_tx.napi);
+ ltq_dma_close(&priv->chan_tx.dma);
+
+ clk_disable_unprepare(priv->clk);
+
+ return 0;
+}
+
+static int xrx200_alloc_skb(struct xrx200_chan *ch)
+{
+ int ret = 0;
+
+ ch->skb[ch->dma.desc] = netdev_alloc_skb_ip_align(ch->priv->net_dev,
+ XRX200_DMA_DATA_LEN);
+ if (!ch->skb[ch->dma.desc]) {
+ ret = -ENOMEM;
+ goto skip;
+ }
+
+ ch->dma.desc_base[ch->dma.desc].addr = dma_map_single(ch->priv->dev,
+ ch->skb[ch->dma.desc]->data, XRX200_DMA_DATA_LEN,
+ DMA_FROM_DEVICE);
+ if (unlikely(dma_mapping_error(ch->priv->dev,
+ ch->dma.desc_base[ch->dma.desc].addr))) {
+ dev_kfree_skb_any(ch->skb[ch->dma.desc]);
+ ret = -ENOMEM;
+ goto skip;
+ }
+
+skip:
+ ch->dma.desc_base[ch->dma.desc].ctl =
+ LTQ_DMA_OWN | LTQ_DMA_RX_OFFSET(NET_IP_ALIGN) |
+ XRX200_DMA_DATA_LEN;
+
+ return ret;
+}
+
+static int xrx200_hw_receive(struct xrx200_chan *ch)
+{
+ struct xrx200_priv *priv = ch->priv;
+ struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc];
+ struct sk_buff *skb = ch->skb[ch->dma.desc];
+ int len = (desc->ctl & LTQ_DMA_SIZE_MASK);
+ struct net_device *net_dev = priv->net_dev;
+ int ret;
+
+ ret = xrx200_alloc_skb(ch);
+
+ ch->dma.desc++;
+ ch->dma.desc %= LTQ_DESC_NUM;
+
+ if (ret) {
+ netdev_err(net_dev, "failed to allocate new rx buffer\n");
+ return ret;
+ }
+
+ skb_put(skb, len);
+ skb->protocol = eth_type_trans(skb, net_dev);
+ netif_receive_skb(skb);
+ net_dev->stats.rx_packets++;
+ net_dev->stats.rx_bytes += len - ETH_FCS_LEN;
+
+ return 0;
+}
+
+static int xrx200_poll_rx(struct napi_struct *napi, int budget)
+{
+ struct xrx200_chan *ch = container_of(napi,
+ struct xrx200_chan, napi);
+ int rx = 0;
+ int ret;
+
+ while (rx < budget) {
+ struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc];
+
+ if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) == LTQ_DMA_C) {
+ ret = xrx200_hw_receive(ch);
+ if (ret)
+ return ret;
+ rx++;
+ } else {
+ break;
+ }
+ }
+
+ if (rx < budget) {
+ napi_complete(&ch->napi);
+ ltq_dma_enable_irq(&ch->dma);
+ }
+
+ return rx;
+}
+
+static int xrx200_tx_housekeeping(struct napi_struct *napi, int budget)
+{
+ struct xrx200_chan *ch = container_of(napi,
+ struct xrx200_chan, napi);
+ struct net_device *net_dev = ch->priv->net_dev;
+ int pkts = 0;
+ int bytes = 0;
+
+ while (pkts < budget) {
+ struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->tx_free];
+
+ if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) == LTQ_DMA_C) {
+ struct sk_buff *skb = ch->skb[ch->tx_free];
+
+ pkts++;
+ bytes += skb->len;
+ ch->skb[ch->tx_free] = NULL;
+ consume_skb(skb);
+ memset(&ch->dma.desc_base[ch->tx_free], 0,
+ sizeof(struct ltq_dma_desc));
+ ch->tx_free++;
+ ch->tx_free %= LTQ_DESC_NUM;
+ } else {
+ break;
+ }
+ }
+
+ net_dev->stats.tx_packets += pkts;
+ net_dev->stats.tx_bytes += bytes;
+ netdev_completed_queue(ch->priv->net_dev, pkts, bytes);
+
+ if (pkts < budget) {
+ napi_complete(&ch->napi);
+ ltq_dma_enable_irq(&ch->dma);
+ }
+
+ return pkts;
+}
+
+static int xrx200_start_xmit(struct sk_buff *skb, struct net_device *net_dev)
+{
+ struct xrx200_priv *priv = netdev_priv(net_dev);
+ struct xrx200_chan *ch = &priv->chan_tx;
+ struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc];
+ u32 byte_offset;
+ dma_addr_t mapping;
+ int len;
+
+ skb->dev = net_dev;
+ if (skb_put_padto(skb, ETH_ZLEN)) {
+ net_dev->stats.tx_dropped++;
+ return NETDEV_TX_OK;
+ }
+
+ len = skb->len;
+
+ if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) || ch->skb[ch->dma.desc]) {
+ netdev_err(net_dev, "tx ring full\n");
+ netif_stop_queue(net_dev);
+ return NETDEV_TX_BUSY;
+ }
+
+ ch->skb[ch->dma.desc] = skb;
+
+ mapping = dma_map_single(priv->dev, skb->data, len, DMA_TO_DEVICE);
+ if (unlikely(dma_mapping_error(priv->dev, mapping)))
+ goto err_drop;
+
+ /* dma needs to start on a 16 byte aligned address */
+ byte_offset = mapping % 16;
+
+ desc->addr = mapping - byte_offset;
+ /* Make sure the address is written before we give it to HW */
+ wmb();
+ desc->ctl = LTQ_DMA_OWN | LTQ_DMA_SOP | LTQ_DMA_EOP |
+ LTQ_DMA_TX_OFFSET(byte_offset) | (len & LTQ_DMA_SIZE_MASK);
+ ch->dma.desc++;
+ ch->dma.desc %= LTQ_DESC_NUM;
+ if (ch->dma.desc == ch->tx_free)
+ netif_stop_queue(net_dev);
+
+ netdev_sent_queue(net_dev, len);
+
+ return NETDEV_TX_OK;
+
+err_drop:
+ dev_kfree_skb(skb);
+ net_dev->stats.tx_dropped++;
+ net_dev->stats.tx_errors++;
+ return NETDEV_TX_OK;
+}
+
+static const struct net_device_ops xrx200_netdev_ops = {
+ .ndo_open = xrx200_open,
+ .ndo_stop = xrx200_close,
+ .ndo_start_xmit = xrx200_start_xmit,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+};
+
+static irqreturn_t xrx200_dma_irq(int irq, void *ptr)
+{
+ struct xrx200_chan *ch = ptr;
+
+ ltq_dma_disable_irq(&ch->dma);
+ ltq_dma_ack_irq(&ch->dma);
+
+ napi_schedule(&ch->napi);
+
+ return IRQ_HANDLED;
+}
+
+static int xrx200_dma_init(struct xrx200_priv *priv)
+{
+ struct xrx200_chan *ch_rx = &priv->chan_rx;
+ struct xrx200_chan *ch_tx = &priv->chan_tx;
+ int ret = 0;
+ int i;
+
+ ltq_dma_init_port(DMA_PORT_ETOP);
+
+ ch_rx->dma.nr = XRX200_DMA_RX;
+ ch_rx->dma.dev = priv->dev;
+ ch_rx->priv = priv;
+
+ ltq_dma_alloc_rx(&ch_rx->dma);
+ for (ch_rx->dma.desc = 0; ch_rx->dma.desc < LTQ_DESC_NUM;
+ ch_rx->dma.desc++) {
+ ret = xrx200_alloc_skb(ch_rx);
+ if (ret)
+ goto rx_free;
+ }
+ ch_rx->dma.desc = 0;
+ ret = devm_request_irq(priv->dev, ch_rx->dma.irq, xrx200_dma_irq, 0,
+ "xrx200_net_rx", &priv->chan_rx);
+ if (ret) {
+ dev_err(priv->dev, "failed to request RX irq %d\n",
+ ch_rx->dma.irq);
+ goto rx_ring_free;
+ }
+
+ ch_tx->dma.nr = XRX200_DMA_TX;
+ ch_tx->dma.dev = priv->dev;
+ ch_tx->priv = priv;
+
+ ltq_dma_alloc_tx(&ch_tx->dma);
+ ret = devm_request_irq(priv->dev, ch_tx->dma.irq, xrx200_dma_irq, 0,
+ "xrx200_net_tx", &priv->chan_tx);
+ if (ret) {
+ dev_err(priv->dev, "failed to request TX irq %d\n",
+ ch_tx->dma.irq);
+ goto tx_free;
+ }
+
+ return ret;
+
+tx_free:
+ ltq_dma_free(&ch_tx->dma);
+
+rx_ring_free:
+ /* free the allocated RX ring */
+ for (i = 0; i < LTQ_DESC_NUM; i++) {
+ if (priv->chan_rx.skb[i])
+ dev_kfree_skb_any(priv->chan_rx.skb[i]);
+ }
+
+rx_free:
+ ltq_dma_free(&ch_rx->dma);
+ return ret;
+}
+
+static void xrx200_hw_cleanup(struct xrx200_priv *priv)
+{
+ int i;
+
+ ltq_dma_free(&priv->chan_tx.dma);
+ ltq_dma_free(&priv->chan_rx.dma);
+
+ /* free the allocated RX ring */
+ for (i = 0; i < LTQ_DESC_NUM; i++)
+ dev_kfree_skb_any(priv->chan_rx.skb[i]);
+}
+
+static int xrx200_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct resource *res;
+ struct xrx200_priv *priv;
+ struct net_device *net_dev;
+ const u8 *mac;
+ int err;
+
+ /* alloc the network device */
+ net_dev = devm_alloc_etherdev(dev, sizeof(struct xrx200_priv));
+ if (!net_dev)
+ return -ENOMEM;
+
+ priv = netdev_priv(net_dev);
+ priv->net_dev = net_dev;
+ priv->dev = dev;
+
+ net_dev->netdev_ops = &xrx200_netdev_ops;
+ SET_NETDEV_DEV(net_dev, dev);
+ net_dev->min_mtu = ETH_ZLEN;
+ net_dev->max_mtu = XRX200_DMA_DATA_LEN;
+
+ /* load the memory ranges */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(dev, "failed to get resources\n");
+ return -ENOENT;
+ }
+
+ priv->pmac_reg = devm_ioremap_resource(dev, res);
+ if (!priv->pmac_reg) {
+ dev_err(dev, "failed to request and remap io ranges\n");
+ return -ENOMEM;
+ }
+
+ priv->chan_rx.dma.irq = platform_get_irq_byname(pdev, "rx");
+ if (priv->chan_rx.dma.irq < 0) {
+ dev_err(dev, "failed to get RX IRQ, %i\n",
+ priv->chan_rx.dma.irq);
+ return -ENOENT;
+ }
+ priv->chan_tx.dma.irq = platform_get_irq_byname(pdev, "tx");
+ if (priv->chan_tx.dma.irq < 0) {
+ dev_err(dev, "failed to get TX IRQ, %i\n",
+ priv->chan_tx.dma.irq);
+ return -ENOENT;
+ }
+
+ /* get the clock */
+ priv->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(priv->clk)) {
+ dev_err(dev, "failed to get clock\n");
+ return PTR_ERR(priv->clk);
+ }
+
+ mac = of_get_mac_address(np);
+ if (mac && is_valid_ether_addr(mac))
+ ether_addr_copy(net_dev->dev_addr, mac);
+ else
+ eth_hw_addr_random(net_dev);
+
+ /* bring up the dma engine and IP core */
+ err = xrx200_dma_init(priv);
+ if (err)
+ return err;
+
+ /* set IPG to 12 */
+ xrx200_pmac_mask(priv, PMAC_RX_IPG_MASK, 0xb, PMAC_RX_IPG);
+
+ /* enable status header, enable CRC */
+ xrx200_pmac_mask(priv, 0,
+ PMAC_HD_CTL_RST | PMAC_HD_CTL_AST | PMAC_HD_CTL_RXSH |
+ PMAC_HD_CTL_AS | PMAC_HD_CTL_AC | PMAC_HD_CTL_RC,
+ PMAC_HD_CTL);
+
+ /* setup NAPI */
+ netif_napi_add(net_dev, &priv->chan_rx.napi, xrx200_poll_rx, 32);
+ netif_napi_add(net_dev, &priv->chan_tx.napi, xrx200_tx_housekeeping, 32);
+
+ platform_set_drvdata(pdev, priv);
+
+ err = register_netdev(net_dev);
+ if (err)
+ goto err_uninit_dma;
+ return err;
+
+err_uninit_dma:
+ xrx200_hw_cleanup(priv);
+
+ return 0;
+}
+
+static int xrx200_remove(struct platform_device *pdev)
+{
+ struct xrx200_priv *priv = platform_get_drvdata(pdev);
+ struct net_device *net_dev = priv->net_dev;
+
+ /* free stack related instances */
+ netif_stop_queue(net_dev);
+ netif_napi_del(&priv->chan_tx.napi);
+ netif_napi_del(&priv->chan_rx.napi);
+
+ /* remove the actual device */
+ unregister_netdev(net_dev);
+
+ /* shut down hardware */
+ xrx200_hw_cleanup(priv);
+
+ return 0;
+}
+
+static const struct of_device_id xrx200_match[] = {
+ { .compatible = "lantiq,xrx200-net" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, xrx200_match);
+
+static struct platform_driver xrx200_driver = {
+ .probe = xrx200_probe,
+ .remove = xrx200_remove,
+ .driver = {
+ .name = "lantiq,xrx200-net",
+ .of_match_table = xrx200_match,
+ },
+};
+
+module_platform_driver(xrx200_driver);
+
+MODULE_AUTHOR("John Crispin <john@phrozen.org>");
+MODULE_DESCRIPTION("Lantiq SoC XRX200 ethernet");
+MODULE_LICENSE("GPL");
--
2.11.0
^ permalink raw reply related [flat|nested] 9+ messages in thread