From: Andrew Lunn <andrew@lunn.ch>
To: Simon Horman <horms@verge.net.au>
Cc: David Miller <davem@davemloft.net>,
netdev <netdev@vger.kernel.org>,
Florian Fainelli <f.fainelli@gmail.com>,
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>,
linux-renesas-soc@vger.kernel.org
Subject: Re: [PATCH v3 net-next 07/12] net: ethernet: Add helper to remove a supported link mode
Date: Thu, 20 Sep 2018 14:51:06 +0200 [thread overview]
Message-ID: <20180920125106.GA13632@lunn.ch> (raw)
In-Reply-To: <20180920080506.qxiy2zeg6xd3xxfz@verge.net.au>
> eth0: no link
> registers for MII PHY 0:
> 1140 7949 0022 1622 0981 c1e1 000d 0000
Hi Simon
The ID registers 0022 1622 indicate this is a Micrel KSZ9031.
Are you using the micrel PHY driver?
> I note a difference in the 3rd line of hex output: 7002 vs 6002
> but I am unsure if that is relevant.
Register 20, or 0x14. The datasheet says "Reserved" and there is no
description given :-(
I will decode the other registers and see if i can find anything.
Andrew
next prev parent reply other threads:[~2018-09-20 18:34 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-09-11 23:53 [PATCH v3 net-next 00/12] Preparing for phylib limkmodes Andrew Lunn
2018-09-11 23:53 ` [PATCH v3 net-next 01/12] net: phy: ste10Xp: Remove wrong SUPPORTED_Pause Andrew Lunn
2018-09-11 23:53 ` [PATCH v3 net-next 02/12] net: phy: et1011c: Remove incorrect missing 1000 Half Andrew Lunn
2018-09-11 23:53 ` [PATCH v3 net-next 03/12] net: phy: bcm63xx: Allow to be built with COMPILE_TEST Andrew Lunn
2018-09-11 23:53 ` [PATCH v3 net-next 04/12] net: ethernet: Use phy_set_max_speed() to limit advertised speed Andrew Lunn
2018-11-22 10:40 ` Anssi Hannula
2018-11-22 18:33 ` Andrew Lunn
2018-09-11 23:53 ` [PATCH v3 net-next 05/12] net: bcmgenet: Fix speed selection for reverse MII Andrew Lunn
2018-09-11 23:53 ` [PATCH v3 net-next 06/12] net: ethernet: Fix up drivers masking pause support Andrew Lunn
2018-09-11 23:53 ` [PATCH v3 net-next 07/12] net: ethernet: Add helper to remove a supported link mode Andrew Lunn
2018-09-17 15:13 ` Simon Horman
2018-09-17 15:38 ` Andrew Lunn
2018-09-18 10:58 ` Simon Horman
2018-09-18 13:02 ` Andrew Lunn
2018-09-19 7:45 ` Simon Horman
2018-09-19 12:32 ` Andrew Lunn
2018-09-20 8:05 ` Simon Horman
2018-09-20 12:51 ` Andrew Lunn [this message]
2018-09-21 8:17 ` Simon Horman
2018-09-24 15:36 ` Simon Horman
2018-09-24 15:50 ` Andrew Lunn
2018-09-25 7:38 ` Simon Horman
2018-09-27 3:08 ` David Miller
2018-10-01 12:43 ` Simon Horman
2018-09-20 13:25 ` Andrew Lunn
2018-09-21 8:13 ` Simon Horman
2018-09-21 13:01 ` Andrew Lunn
2018-09-25 8:40 ` Simon Horman
2018-09-11 23:53 ` [PATCH v3 net-next 08/12] net: ethernet: Add helper for MACs which support asym pause Andrew Lunn
2018-09-11 23:53 ` [PATCH v3 net-next 09/12] net: ethernet: Add helper for MACs which support pause Andrew Lunn
2018-09-11 23:53 ` [PATCH v3 net-next 10/12] net: ethernet: Add helper for set_pauseparam for Asym Pause Andrew Lunn
2018-09-11 23:53 ` [PATCH v3 net-next 11/12] net: ethernet: Add helper for set_pauseparam for Pause Andrew Lunn
2018-09-11 23:53 ` [PATCH v3 net-next 12/12] net: ethernet: Add helper to determine if pause configuration is supported Andrew Lunn
2018-09-13 3:24 ` [PATCH v3 net-next 00/12] Preparing for phylib limkmodes David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180920125106.GA13632@lunn.ch \
--to=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=horms@verge.net.au \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=sergei.shtylyov@cogentembedded.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).