From: Maxime Chevallier <maxime.chevallier@bootlin.com>
To: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>,
Kishon Vijay Abraham I <kishon@ti.com>,
Russell King - ARM Linux <linux@armlinux.org.uk>,
<netdev@vger.kernel.org>, Sekhar Nori <nsekhar@ti.com>,
<linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
Tony Lindgren <tony@atomide.com>,
<linux-amlogic@lists.infradead.org>,
<linux-mediatek@lists.infradead.org>,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
Antoine Tenart <antoine.tenart@free-electrons.com>,
Quentin Schulz <quentin.schulz@bootlin.com>,
Vivek Gautam <vivek.gautam@codeaurora.org>,
Maxime Ripard <maxime.ripard@bootlin.com>,
Chen-Yu Tsai <wens@csie.org>, Carlo Caione <carlo@caione.org>,
Chunfeng Yun <chunfeng.yun@mediatek.com>,
Matthias Brugger <matthias.bgg@gmail.com>,
Manu Gaut
Subject: Re: [PATCH v2 4/5] phy: mvebu-cp110-comphy: convert to use eth phy mode and submode
Date: Mon, 19 Nov 2018 09:26:32 +0100 [thread overview]
Message-ID: <20181119092632.7048bc46@bootlin.com> (raw)
In-Reply-To: <20181109234755.21687-5-grygorii.strashko@ti.com>
Hi Grygorii,
On Fri, 9 Nov 2018 17:47:54 -0600
Grygorii Strashko <grygorii.strashko@ti.com> wrote:
>Convert mvebu-cp110-comphy PHY driver to use recently introduced
>PHY_MODE_ETHERNET and phy_set_mode_ext().
Sorry I missed your V2, hopefully I tested the right version this time.
Tested on MCBin, this works just fine.
Thanks,
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
>Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
>---
> drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 19 +-----
> drivers/phy/marvell/phy-mvebu-cp110-comphy.c | 83 ++++++++++++++-----------
> 2 files changed, 48 insertions(+), 54 deletions(-)
>
>diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
>index 7a37a37..731793a 100644
>--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
>+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
>@@ -1165,28 +1165,13 @@ static void mvpp22_gop_setup_irq(struct mvpp2_port *port)
> */
> static int mvpp22_comphy_init(struct mvpp2_port *port)
> {
>- enum phy_mode mode;
> int ret;
>
> if (!port->comphy)
> return 0;
>
>- switch (port->phy_interface) {
>- case PHY_INTERFACE_MODE_SGMII:
>- case PHY_INTERFACE_MODE_1000BASEX:
>- mode = PHY_MODE_SGMII;
>- break;
>- case PHY_INTERFACE_MODE_2500BASEX:
>- mode = PHY_MODE_2500SGMII;
>- break;
>- case PHY_INTERFACE_MODE_10GKR:
>- mode = PHY_MODE_10GKR;
>- break;
>- default:
>- return -EINVAL;
>- }
>-
>- ret = phy_set_mode(port->comphy, mode);
>+ ret = phy_set_mode_ext(port->comphy, PHY_MODE_ETHERNET,
>+ port->phy_interface);
> if (ret)
> return ret;
>
>diff --git a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
>index 79b52c3..7dee72b 100644
>--- a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
>+++ b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
>@@ -9,6 +9,7 @@
> #include <linux/iopoll.h>
> #include <linux/mfd/syscon.h>
> #include <linux/module.h>
>+#include <linux/phy.h>
> #include <linux/phy/phy.h>
> #include <linux/platform_device.h>
> #include <linux/regmap.h>
>@@ -131,26 +132,26 @@ struct mvebu_comhy_conf {
>
> static const struct mvebu_comhy_conf mvebu_comphy_cp110_modes[] = {
> /* lane 0 */
>- MVEBU_COMPHY_CONF(0, 1, PHY_MODE_SGMII, 0x1),
>- MVEBU_COMPHY_CONF(0, 1, PHY_MODE_2500SGMII, 0x1),
>+ MVEBU_COMPHY_CONF(0, 1, PHY_INTERFACE_MODE_SGMII, 0x1),
>+ MVEBU_COMPHY_CONF(0, 1, PHY_INTERFACE_MODE_2500BASEX, 0x1),
> /* lane 1 */
>- MVEBU_COMPHY_CONF(1, 2, PHY_MODE_SGMII, 0x1),
>- MVEBU_COMPHY_CONF(1, 2, PHY_MODE_2500SGMII, 0x1),
>+ MVEBU_COMPHY_CONF(1, 2, PHY_INTERFACE_MODE_SGMII, 0x1),
>+ MVEBU_COMPHY_CONF(1, 2, PHY_INTERFACE_MODE_2500BASEX, 0x1),
> /* lane 2 */
>- MVEBU_COMPHY_CONF(2, 0, PHY_MODE_SGMII, 0x1),
>- MVEBU_COMPHY_CONF(2, 0, PHY_MODE_2500SGMII, 0x1),
>- MVEBU_COMPHY_CONF(2, 0, PHY_MODE_10GKR, 0x1),
>+ MVEBU_COMPHY_CONF(2, 0, PHY_INTERFACE_MODE_SGMII, 0x1),
>+ MVEBU_COMPHY_CONF(2, 0, PHY_INTERFACE_MODE_2500BASEX, 0x1),
>+ MVEBU_COMPHY_CONF(2, 0, PHY_INTERFACE_MODE_10GKR, 0x1),
> /* lane 3 */
>- MVEBU_COMPHY_CONF(3, 1, PHY_MODE_SGMII, 0x2),
>- MVEBU_COMPHY_CONF(3, 1, PHY_MODE_2500SGMII, 0x2),
>+ MVEBU_COMPHY_CONF(3, 1, PHY_INTERFACE_MODE_SGMII, 0x2),
>+ MVEBU_COMPHY_CONF(3, 1, PHY_INTERFACE_MODE_2500BASEX, 0x2),
> /* lane 4 */
>- MVEBU_COMPHY_CONF(4, 0, PHY_MODE_SGMII, 0x2),
>- MVEBU_COMPHY_CONF(4, 0, PHY_MODE_2500SGMII, 0x2),
>- MVEBU_COMPHY_CONF(4, 0, PHY_MODE_10GKR, 0x2),
>- MVEBU_COMPHY_CONF(4, 1, PHY_MODE_SGMII, 0x1),
>+ MVEBU_COMPHY_CONF(4, 0, PHY_INTERFACE_MODE_SGMII, 0x2),
>+ MVEBU_COMPHY_CONF(4, 0, PHY_INTERFACE_MODE_2500BASEX, 0x2),
>+ MVEBU_COMPHY_CONF(4, 0, PHY_INTERFACE_MODE_10GKR, 0x2),
>+ MVEBU_COMPHY_CONF(4, 1, PHY_INTERFACE_MODE_SGMII, 0x1),
> /* lane 5 */
>- MVEBU_COMPHY_CONF(5, 2, PHY_MODE_SGMII, 0x1),
>- MVEBU_COMPHY_CONF(5, 2, PHY_MODE_2500SGMII, 0x1),
>+ MVEBU_COMPHY_CONF(5, 2, PHY_INTERFACE_MODE_SGMII, 0x1),
>+ MVEBU_COMPHY_CONF(5, 2, PHY_INTERFACE_MODE_2500BASEX, 0x1),
> };
>
> struct mvebu_comphy_priv {
>@@ -163,10 +164,12 @@ struct mvebu_comphy_lane {
> struct mvebu_comphy_priv *priv;
> unsigned id;
> enum phy_mode mode;
>+ int submode;
> int port;
> };
>
>-static int mvebu_comphy_get_mux(int lane, int port, enum phy_mode mode)
>+static int mvebu_comphy_get_mux(int lane, int port,
>+ enum phy_mode mode, int submode)
> {
> int i, n = ARRAY_SIZE(mvebu_comphy_cp110_modes);
>
>@@ -177,7 +180,7 @@ static int mvebu_comphy_get_mux(int lane, int port, enum phy_mode mode)
> for (i = 0; i < n; i++) {
> if (mvebu_comphy_cp110_modes[i].lane == lane &&
> mvebu_comphy_cp110_modes[i].port == port &&
>- mvebu_comphy_cp110_modes[i].mode == mode)
>+ mvebu_comphy_cp110_modes[i].mode == submode)
> break;
> }
>
>@@ -187,8 +190,7 @@ static int mvebu_comphy_get_mux(int lane, int port, enum phy_mode mode)
> return mvebu_comphy_cp110_modes[i].mux;
> }
>
>-static void mvebu_comphy_ethernet_init_reset(struct mvebu_comphy_lane *lane,
>- enum phy_mode mode)
>+static void mvebu_comphy_ethernet_init_reset(struct mvebu_comphy_lane *lane)
> {
> struct mvebu_comphy_priv *priv = lane->priv;
> u32 val;
>@@ -206,14 +208,14 @@ static void mvebu_comphy_ethernet_init_reset(struct mvebu_comphy_lane *lane,
> MVEBU_COMPHY_SERDES_CFG0_HALF_BUS |
> MVEBU_COMPHY_SERDES_CFG0_GEN_RX(0xf) |
> MVEBU_COMPHY_SERDES_CFG0_GEN_TX(0xf));
>- if (mode == PHY_MODE_10GKR)
>+ if (lane->submode == PHY_INTERFACE_MODE_10GKR)
> val |= MVEBU_COMPHY_SERDES_CFG0_GEN_RX(0xe) |
> MVEBU_COMPHY_SERDES_CFG0_GEN_TX(0xe);
>- else if (mode == PHY_MODE_2500SGMII)
>+ else if (lane->submode == PHY_INTERFACE_MODE_2500BASEX)
> val |= MVEBU_COMPHY_SERDES_CFG0_GEN_RX(0x8) |
> MVEBU_COMPHY_SERDES_CFG0_GEN_TX(0x8) |
> MVEBU_COMPHY_SERDES_CFG0_HALF_BUS;
>- else if (mode == PHY_MODE_SGMII)
>+ else if (lane->submode == PHY_INTERFACE_MODE_SGMII)
> val |= MVEBU_COMPHY_SERDES_CFG0_GEN_RX(0x6) |
> MVEBU_COMPHY_SERDES_CFG0_GEN_TX(0x6) |
> MVEBU_COMPHY_SERDES_CFG0_HALF_BUS;
>@@ -243,7 +245,7 @@ static void mvebu_comphy_ethernet_init_reset(struct mvebu_comphy_lane *lane,
> /* refclk selection */
> val = readl(priv->base + MVEBU_COMPHY_MISC_CTRL0(lane->id));
> val &= ~MVEBU_COMPHY_MISC_CTRL0_REFCLK_SEL;
>- if (mode == PHY_MODE_10GKR)
>+ if (lane->submode == PHY_INTERFACE_MODE_10GKR)
> val |= MVEBU_COMPHY_MISC_CTRL0_ICP_FORCE;
> writel(val, priv->base + MVEBU_COMPHY_MISC_CTRL0(lane->id));
>
>@@ -261,8 +263,7 @@ static void mvebu_comphy_ethernet_init_reset(struct mvebu_comphy_lane *lane,
> writel(val, priv->base + MVEBU_COMPHY_LOOPBACK(lane->id));
> }
>
>-static int mvebu_comphy_init_plls(struct mvebu_comphy_lane *lane,
>- enum phy_mode mode)
>+static int mvebu_comphy_init_plls(struct mvebu_comphy_lane *lane)
> {
> struct mvebu_comphy_priv *priv = lane->priv;
> u32 val;
>@@ -303,13 +304,13 @@ static int mvebu_comphy_init_plls(struct mvebu_comphy_lane *lane,
> return 0;
> }
>
>-static int mvebu_comphy_set_mode_sgmii(struct phy *phy, enum phy_mode mode)
>+static int mvebu_comphy_set_mode_sgmii(struct phy *phy)
> {
> struct mvebu_comphy_lane *lane = phy_get_drvdata(phy);
> struct mvebu_comphy_priv *priv = lane->priv;
> u32 val;
>
>- mvebu_comphy_ethernet_init_reset(lane, mode);
>+ mvebu_comphy_ethernet_init_reset(lane);
>
> val = readl(priv->base + MVEBU_COMPHY_RX_CTRL1(lane->id));
> val &= ~MVEBU_COMPHY_RX_CTRL1_CLK8T_EN;
>@@ -330,7 +331,7 @@ static int mvebu_comphy_set_mode_sgmii(struct phy *phy, enum phy_mode mode)
> val |= MVEBU_COMPHY_GEN1_S0_TX_EMPH(0x1);
> writel(val, priv->base + MVEBU_COMPHY_GEN1_S0(lane->id));
>
>- return mvebu_comphy_init_plls(lane, PHY_MODE_SGMII);
>+ return mvebu_comphy_init_plls(lane);
> }
>
> static int mvebu_comphy_set_mode_10gkr(struct phy *phy)
>@@ -339,7 +340,7 @@ static int mvebu_comphy_set_mode_10gkr(struct phy *phy)
> struct mvebu_comphy_priv *priv = lane->priv;
> u32 val;
>
>- mvebu_comphy_ethernet_init_reset(lane, PHY_MODE_10GKR);
>+ mvebu_comphy_ethernet_init_reset(lane);
>
> val = readl(priv->base + MVEBU_COMPHY_RX_CTRL1(lane->id));
> val |= MVEBU_COMPHY_RX_CTRL1_RXCLK2X_SEL |
>@@ -469,7 +470,7 @@ static int mvebu_comphy_set_mode_10gkr(struct phy *phy)
> val |= MVEBU_COMPHY_EXT_SELV_RX_SAMPL(0x1a);
> writel(val, priv->base + MVEBU_COMPHY_EXT_SELV(lane->id));
>
>- return mvebu_comphy_init_plls(lane, PHY_MODE_10GKR);
>+ return mvebu_comphy_init_plls(lane);
> }
>
> static int mvebu_comphy_power_on(struct phy *phy)
>@@ -479,7 +480,8 @@ static int mvebu_comphy_power_on(struct phy *phy)
> int ret, mux;
> u32 val;
>
>- mux = mvebu_comphy_get_mux(lane->id, lane->port, lane->mode);
>+ mux = mvebu_comphy_get_mux(lane->id, lane->port,
>+ lane->mode, lane->submode);
> if (mux < 0)
> return -ENOTSUPP;
>
>@@ -492,12 +494,12 @@ static int mvebu_comphy_power_on(struct phy *phy)
> val |= mux << MVEBU_COMPHY_SELECTOR_PHY(lane->id);
> regmap_write(priv->regmap, MVEBU_COMPHY_SELECTOR, val);
>
>- switch (lane->mode) {
>- case PHY_MODE_SGMII:
>- case PHY_MODE_2500SGMII:
>- ret = mvebu_comphy_set_mode_sgmii(phy, lane->mode);
>+ switch (lane->submode) {
>+ case PHY_INTERFACE_MODE_SGMII:
>+ case PHY_INTERFACE_MODE_2500BASEX:
>+ ret = mvebu_comphy_set_mode_sgmii(phy);
> break;
>- case PHY_MODE_10GKR:
>+ case PHY_INTERFACE_MODE_10GKR:
> ret = mvebu_comphy_set_mode_10gkr(phy);
> break;
> default:
>@@ -517,10 +519,17 @@ static int mvebu_comphy_set_mode(struct phy *phy,
> {
> struct mvebu_comphy_lane *lane = phy_get_drvdata(phy);
>
>- if (mvebu_comphy_get_mux(lane->id, lane->port, mode) < 0)
>+ if (mode != PHY_MODE_ETHERNET)
>+ return -EINVAL;
>+
>+ if (submode == PHY_INTERFACE_MODE_1000BASEX)
>+ submode = PHY_INTERFACE_MODE_SGMII;
>+
>+ if (mvebu_comphy_get_mux(lane->id, lane->port, mode, submode) < 0)
> return -EINVAL;
>
> lane->mode = mode;
>+ lane->submode = submode;
> return 0;
> }
>
--
Maxime Chevallier, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com
next prev parent reply other threads:[~2018-11-19 8:26 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-09 23:47 [PATCH v2 0/5] phy: core: rework phy_set_mode to accept phy mode and submode Grygorii Strashko
2018-11-09 23:47 ` [PATCH v2 1/5] " Grygorii Strashko
2018-11-09 23:47 ` [PATCH v2 2/5] phy: core: add PHY_MODE_ETHERNET Grygorii Strashko
2018-11-09 23:47 ` [PATCH v2 3/5] phy: ocelot-serdes: convert to use eth phy mode and submode Grygorii Strashko
2018-11-12 10:42 ` Kishon Vijay Abraham I
2018-11-16 11:15 ` Quentin Schulz
2018-11-16 21:00 ` Grygorii Strashko
2018-11-09 23:47 ` [PATCH v2 4/5] phy: mvebu-cp110-comphy: " Grygorii Strashko
2018-11-12 10:48 ` Kishon Vijay Abraham I
2018-11-19 8:26 ` Maxime Chevallier [this message]
2018-11-19 16:48 ` Antoine Tenart
2018-11-19 17:07 ` Russell King - ARM Linux
2018-11-19 22:42 ` Grygorii Strashko
2018-11-09 23:47 ` [PATCH v2 5/5] phy: core: clean up unused ethernet specific phy modes Grygorii Strashko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181119092632.7048bc46@bootlin.com \
--to=maxime.chevallier@bootlin.com \
--cc=alexandre.belloni@bootlin.com \
--cc=antoine.tenart@free-electrons.com \
--cc=carlo@caione.org \
--cc=chunfeng.yun@mediatek.com \
--cc=davem@davemloft.net \
--cc=grygorii.strashko@ti.com \
--cc=kishon@ti.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux@armlinux.org.uk \
--cc=matthias.bgg@gmail.com \
--cc=maxime.ripard@bootlin.com \
--cc=netdev@vger.kernel.org \
--cc=nsekhar@ti.com \
--cc=quentin.schulz@bootlin.com \
--cc=tony@atomide.com \
--cc=vivek.gautam@codeaurora.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).