From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: Ido Schimmel <idosch@mellanox.com>,
"David S . Miller" <davem@davemloft.net>,
Sasha Levin <sashal@kernel.org>,
netdev@vger.kernel.org
Subject: [PATCH AUTOSEL 4.19 65/73] mlxsw: spectrum_switchdev: Fix VLAN device deletion via ioctl
Date: Wed, 12 Dec 2018 23:28:30 -0500 [thread overview]
Message-ID: <20181213042838.75160-65-sashal@kernel.org> (raw)
In-Reply-To: <20181213042838.75160-1-sashal@kernel.org>
From: Ido Schimmel <idosch@mellanox.com>
[ Upstream commit 993107fea5eefdfdfde1ca38d3f01f0bebf76e77 ]
When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.
The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.
Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
.../net/ethernet/mellanox/mlxsw/spectrum_switchdev.c | 10 ++++++++--
1 file changed, 8 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
index 7715f1ed2bcb..4eb64cb0d9a1 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
@@ -286,7 +286,13 @@ static bool
mlxsw_sp_bridge_port_should_destroy(const struct mlxsw_sp_bridge_port *
bridge_port)
{
- struct mlxsw_sp *mlxsw_sp = mlxsw_sp_lower_get(bridge_port->dev);
+ struct net_device *dev = bridge_port->dev;
+ struct mlxsw_sp *mlxsw_sp;
+
+ if (is_vlan_dev(dev))
+ mlxsw_sp = mlxsw_sp_lower_get(vlan_dev_real_dev(dev));
+ else
+ mlxsw_sp = mlxsw_sp_lower_get(dev);
/* In case ports were pulled from out of a bridged LAG, then
* it's possible the reference count isn't zero, yet the bridge
@@ -2020,7 +2026,7 @@ mlxsw_sp_bridge_8021d_port_leave(struct mlxsw_sp_bridge_device *bridge_device,
vid = is_vlan_dev(dev) ? vlan_dev_vlan_id(dev) : 1;
mlxsw_sp_port_vlan = mlxsw_sp_port_vlan_find_by_vid(mlxsw_sp_port, vid);
- if (WARN_ON(!mlxsw_sp_port_vlan))
+ if (!mlxsw_sp_port_vlan)
return;
mlxsw_sp_port_vlan_bridge_leave(mlxsw_sp_port_vlan);
--
2.19.1
next prev parent reply other threads:[~2018-12-13 4:28 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-12-13 4:27 [PATCH AUTOSEL 4.19 01/73] mac80211_hwsim: fix module init error paths for netlink Sasha Levin
2018-12-13 4:27 ` [PATCH AUTOSEL 4.19 06/73] tools/bpf: fix two test_btf unit test cases Sasha Levin
2018-12-13 4:27 ` [PATCH AUTOSEL 4.19 07/73] tools/bpf: add addition type tests to test_btf Sasha Levin
2018-12-13 4:27 ` [PATCH AUTOSEL 4.19 08/73] net: ethernet: ave: Replace NET_IP_ALIGN with AVE_FRAME_HEADROOM Sasha Levin
2018-12-13 4:27 ` [PATCH AUTOSEL 4.19 09/73] net: phy: sfp: correct store of detected link modes Sasha Levin
2018-12-13 4:27 ` [PATCH AUTOSEL 4.19 20/73] net: stmmac: Move debugfs init/exit to ->probe()/->remove() Sasha Levin
2018-12-13 4:27 ` [PATCH AUTOSEL 4.19 21/73] net: aquantia: fix rx checksum offload bits Sasha Levin
2018-12-13 4:27 ` [PATCH AUTOSEL 4.19 22/73] bonding: fix 802.3ad state sent to partner when unbinding slave Sasha Levin
2018-12-13 4:27 ` [PATCH AUTOSEL 4.19 23/73] bpf: Fix verifier log string check for bad alignment Sasha Levin
2018-12-13 4:27 ` [PATCH AUTOSEL 4.19 24/73] liquidio: read sc->iq_no before release sc Sasha Levin
2018-12-13 4:27 ` [PATCH AUTOSEL 4.19 26/73] SUNRPC: Fix leak of krb5p encode pages Sasha Levin
2018-12-13 4:27 ` [PATCH AUTOSEL 4.19 27/73] SUNRPC: Fix a potential race in xprt_connect() Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 42/73] net: phy: don't allow __set_phy_supported to add unsupported modes Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 43/73] net: 8139cp: fix a BUG triggered by changing mtu with network traffic Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 44/73] net: phy: Fix not to call phy_resume() if PHY is not attached Sasha Levin
2018-12-13 4:48 ` Yoshihiro Shimoda
2018-12-19 13:43 ` Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 45/73] net: phy: micrel: add toggling phy reset " Sasha Levin
2018-12-13 4:44 ` Yoshihiro Shimoda
2018-12-19 13:43 ` Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 46/73] macvlan: return correct error value Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 47/73] mv88e6060: disable hardware level MAC learning Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 48/73] net/mlx4_en: Change min MTU size to ETH_MIN_MTU Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 49/73] net/mlx4_en: Fix build break when CONFIG_INET is off Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 50/73] bpf: check pending signals while verifying programs Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 54/73] ethernet: fman: fix wrong of_node_put() in probe function Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 56/73] net: mvpp2: fix detection of 10G SFP modules Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 57/73] net: mvpp2: fix phylink handling of invalid PHY modes Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 64/73] vhost/vsock: fix reset orphans race with close timeout Sasha Levin
2018-12-13 4:28 ` Sasha Levin [this message]
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 72/73] Revert "net/ibm/emac: wrong bit is used for STA control" Sasha Levin
2018-12-13 4:28 ` [PATCH AUTOSEL 4.19 73/73] net/mlx4_core: Correctly set PFC param if global pause is turned off Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181213042838.75160-65-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=davem@davemloft.net \
--cc=idosch@mellanox.com \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).