* [PATCH] can: bcm: check timer values before ktime conversion @ 2019-01-12 21:57 Oliver Hartkopp 2019-01-12 21:57 ` Oliver Hartkopp 2019-01-12 22:16 ` Andre Naujoks 0 siblings, 2 replies; 10+ messages in thread From: Oliver Hartkopp @ 2019-01-12 21:57 UTC (permalink / raw) To: davem, netdev Cc: linux-can, lifeasageek, threeearcat, syzkaller, Oliver Hartkopp, Kyungtae Kim, linux-stable Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup() when the conversion into ktime multiplies the given value with NSEC_PER_USEC (1000). Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2 Add a check for the given tv_usec, so that the value stays below one second. Additionally limit the tv_sec value to a reasonable value for CAN related use-cases of 15 minutes. Reported-by: Kyungtae Kim <kt0755@gmail.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26 --- net/can/bcm.c | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/net/can/bcm.c b/net/can/bcm.c index 0af8f0db892a..ff3799be077b 100644 --- a/net/can/bcm.c +++ b/net/can/bcm.c @@ -67,6 +67,9 @@ */ #define MAX_NFRAMES 256 +/* limit timers to 15 minutes for sending/timeouts */ +#define BCM_TIMER_SEC_MAX (15*60) + /* use of last_frames[index].flags */ #define RX_RECV 0x40 /* received data for this element */ #define RX_THR 0x80 /* element not been sent due to throttle feature */ @@ -140,6 +143,18 @@ static inline ktime_t bcm_timeval_to_ktime(struct bcm_timeval tv) return ktime_set(tv.tv_sec, tv.tv_usec * NSEC_PER_USEC); } +/* check limitations for timeval provided by user */ +static int bcm_is_invalid_tv(struct bcm_msg_head *msg_head) +{ + if ((msg_head->ival1.tv_sec > BCM_TIMER_SEC_MAX) || + (msg_head->ival1.tv_usec >= USEC_PER_SEC) || + (msg_head->ival2.tv_sec > BCM_TIMER_SEC_MAX) || + (msg_head->ival2.tv_usec >= USEC_PER_SEC)) + return 1; + + return 0; +} + #define CFSIZ(flags) ((flags & CAN_FD_FRAME) ? CANFD_MTU : CAN_MTU) #define OPSIZ sizeof(struct bcm_op) #define MHSIZ sizeof(struct bcm_msg_head) @@ -873,6 +888,10 @@ static int bcm_tx_setup(struct bcm_msg_head *msg_head, struct msghdr *msg, if (msg_head->nframes < 1 || msg_head->nframes > MAX_NFRAMES) return -EINVAL; + /* check timeval limitations */ + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) + return -EINVAL; + /* check the given can_id */ op = bcm_find_op(&bo->tx_ops, msg_head, ifindex); if (op) { @@ -1053,6 +1072,10 @@ static int bcm_rx_setup(struct bcm_msg_head *msg_head, struct msghdr *msg, (!(msg_head->can_id & CAN_RTR_FLAG)))) return -EINVAL; + /* check timeval limitations */ + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) + return -EINVAL; + /* check the given can_id */ op = bcm_find_op(&bo->rx_ops, msg_head, ifindex); if (op) { -- 2.20.1 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH] can: bcm: check timer values before ktime conversion 2019-01-12 21:57 [PATCH] can: bcm: check timer values before ktime conversion Oliver Hartkopp @ 2019-01-12 21:57 ` Oliver Hartkopp 2019-01-12 22:16 ` Andre Naujoks 1 sibling, 0 replies; 10+ messages in thread From: Oliver Hartkopp @ 2019-01-12 21:57 UTC (permalink / raw) To: davem, netdev Cc: linux-can, lifeasageek, threeearcat, syzkaller, Oliver Hartkopp, Kyungtae Kim, linux-stable Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup() when the conversion into ktime multiplies the given value with NSEC_PER_USEC (1000). Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2 Add a check for the given tv_usec, so that the value stays below one second. Additionally limit the tv_sec value to a reasonable value for CAN related use-cases of 15 minutes. Reported-by: Kyungtae Kim <kt0755@gmail.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26 --- net/can/bcm.c | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/net/can/bcm.c b/net/can/bcm.c index 0af8f0db892a..ff3799be077b 100644 --- a/net/can/bcm.c +++ b/net/can/bcm.c @@ -67,6 +67,9 @@ */ #define MAX_NFRAMES 256 +/* limit timers to 15 minutes for sending/timeouts */ +#define BCM_TIMER_SEC_MAX (15*60) + /* use of last_frames[index].flags */ #define RX_RECV 0x40 /* received data for this element */ #define RX_THR 0x80 /* element not been sent due to throttle feature */ @@ -140,6 +143,18 @@ static inline ktime_t bcm_timeval_to_ktime(struct bcm_timeval tv) return ktime_set(tv.tv_sec, tv.tv_usec * NSEC_PER_USEC); } +/* check limitations for timeval provided by user */ +static int bcm_is_invalid_tv(struct bcm_msg_head *msg_head) +{ + if ((msg_head->ival1.tv_sec > BCM_TIMER_SEC_MAX) || + (msg_head->ival1.tv_usec >= USEC_PER_SEC) || + (msg_head->ival2.tv_sec > BCM_TIMER_SEC_MAX) || + (msg_head->ival2.tv_usec >= USEC_PER_SEC)) + return 1; + + return 0; +} + #define CFSIZ(flags) ((flags & CAN_FD_FRAME) ? CANFD_MTU : CAN_MTU) #define OPSIZ sizeof(struct bcm_op) #define MHSIZ sizeof(struct bcm_msg_head) @@ -873,6 +888,10 @@ static int bcm_tx_setup(struct bcm_msg_head *msg_head, struct msghdr *msg, if (msg_head->nframes < 1 || msg_head->nframes > MAX_NFRAMES) return -EINVAL; + /* check timeval limitations */ + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) + return -EINVAL; + /* check the given can_id */ op = bcm_find_op(&bo->tx_ops, msg_head, ifindex); if (op) { @@ -1053,6 +1072,10 @@ static int bcm_rx_setup(struct bcm_msg_head *msg_head, struct msghdr *msg, (!(msg_head->can_id & CAN_RTR_FLAG)))) return -EINVAL; + /* check timeval limitations */ + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) + return -EINVAL; + /* check the given can_id */ op = bcm_find_op(&bo->rx_ops, msg_head, ifindex); if (op) { -- 2.20.1 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH] can: bcm: check timer values before ktime conversion 2019-01-12 21:57 [PATCH] can: bcm: check timer values before ktime conversion Oliver Hartkopp 2019-01-12 21:57 ` Oliver Hartkopp @ 2019-01-12 22:16 ` Andre Naujoks 2019-01-12 22:16 ` Andre Naujoks 2019-01-12 22:30 ` Oliver Hartkopp 1 sibling, 2 replies; 10+ messages in thread From: Andre Naujoks @ 2019-01-12 22:16 UTC (permalink / raw) To: Oliver Hartkopp, davem, netdev Cc: linux-can, lifeasageek, threeearcat, syzkaller, Kyungtae Kim, linux-stable Hi. The 15 minute limit seems arbitrary to me. I'd be surprised if an (R|T)X_SETUP failed because of a timeout greater than this. Are there any problems with allowing larger timeouts? If not, I do not see a reason to restrict this. Regards Andre On 1/12/19 10:57 PM, Oliver Hartkopp wrote: > Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup() when > the conversion into ktime multiplies the given value with NSEC_PER_USEC (1000). > > Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2 > > Add a check for the given tv_usec, so that the value stays below one second. > Additionally limit the tv_sec value to a reasonable value for CAN related > use-cases of 15 minutes. > > Reported-by: Kyungtae Kim <kt0755@gmail.com> > Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> > Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> > Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26 > --- > net/can/bcm.c | 23 +++++++++++++++++++++++ > 1 file changed, 23 insertions(+) > > diff --git a/net/can/bcm.c b/net/can/bcm.c > index 0af8f0db892a..ff3799be077b 100644 > --- a/net/can/bcm.c > +++ b/net/can/bcm.c > @@ -67,6 +67,9 @@ > */ > #define MAX_NFRAMES 256 > > +/* limit timers to 15 minutes for sending/timeouts */ > +#define BCM_TIMER_SEC_MAX (15*60) > + > /* use of last_frames[index].flags */ > #define RX_RECV 0x40 /* received data for this element */ > #define RX_THR 0x80 /* element not been sent due to throttle feature */ > @@ -140,6 +143,18 @@ static inline ktime_t bcm_timeval_to_ktime(struct bcm_timeval tv) > return ktime_set(tv.tv_sec, tv.tv_usec * NSEC_PER_USEC); > } > > +/* check limitations for timeval provided by user */ > +static int bcm_is_invalid_tv(struct bcm_msg_head *msg_head) > +{ > + if ((msg_head->ival1.tv_sec > BCM_TIMER_SEC_MAX) || > + (msg_head->ival1.tv_usec >= USEC_PER_SEC) || > + (msg_head->ival2.tv_sec > BCM_TIMER_SEC_MAX) || > + (msg_head->ival2.tv_usec >= USEC_PER_SEC)) > + return 1; > + > + return 0; > +} > + > #define CFSIZ(flags) ((flags & CAN_FD_FRAME) ? CANFD_MTU : CAN_MTU) > #define OPSIZ sizeof(struct bcm_op) > #define MHSIZ sizeof(struct bcm_msg_head) > @@ -873,6 +888,10 @@ static int bcm_tx_setup(struct bcm_msg_head *msg_head, struct msghdr *msg, > if (msg_head->nframes < 1 || msg_head->nframes > MAX_NFRAMES) > return -EINVAL; > > + /* check timeval limitations */ > + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) > + return -EINVAL; > + > /* check the given can_id */ > op = bcm_find_op(&bo->tx_ops, msg_head, ifindex); > if (op) { > @@ -1053,6 +1072,10 @@ static int bcm_rx_setup(struct bcm_msg_head *msg_head, struct msghdr *msg, > (!(msg_head->can_id & CAN_RTR_FLAG)))) > return -EINVAL; > > + /* check timeval limitations */ > + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) > + return -EINVAL; > + > /* check the given can_id */ > op = bcm_find_op(&bo->rx_ops, msg_head, ifindex); > if (op) { > ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH] can: bcm: check timer values before ktime conversion 2019-01-12 22:16 ` Andre Naujoks @ 2019-01-12 22:16 ` Andre Naujoks 2019-01-12 22:30 ` Oliver Hartkopp 1 sibling, 0 replies; 10+ messages in thread From: Andre Naujoks @ 2019-01-12 22:16 UTC (permalink / raw) To: Oliver Hartkopp, davem, netdev Cc: linux-can, lifeasageek, threeearcat, syzkaller, Kyungtae Kim, linux-stable Hi. The 15 minute limit seems arbitrary to me. I'd be surprised if an (R|T)X_SETUP failed because of a timeout greater than this. Are there any problems with allowing larger timeouts? If not, I do not see a reason to restrict this. Regards Andre On 1/12/19 10:57 PM, Oliver Hartkopp wrote: > Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup() when > the conversion into ktime multiplies the given value with NSEC_PER_USEC (1000). > > Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2 > > Add a check for the given tv_usec, so that the value stays below one second. > Additionally limit the tv_sec value to a reasonable value for CAN related > use-cases of 15 minutes. > > Reported-by: Kyungtae Kim <kt0755@gmail.com> > Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> > Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> > Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26 > --- > net/can/bcm.c | 23 +++++++++++++++++++++++ > 1 file changed, 23 insertions(+) > > diff --git a/net/can/bcm.c b/net/can/bcm.c > index 0af8f0db892a..ff3799be077b 100644 > --- a/net/can/bcm.c > +++ b/net/can/bcm.c > @@ -67,6 +67,9 @@ > */ > #define MAX_NFRAMES 256 > > +/* limit timers to 15 minutes for sending/timeouts */ > +#define BCM_TIMER_SEC_MAX (15*60) > + > /* use of last_frames[index].flags */ > #define RX_RECV 0x40 /* received data for this element */ > #define RX_THR 0x80 /* element not been sent due to throttle feature */ > @@ -140,6 +143,18 @@ static inline ktime_t bcm_timeval_to_ktime(struct bcm_timeval tv) > return ktime_set(tv.tv_sec, tv.tv_usec * NSEC_PER_USEC); > } > > +/* check limitations for timeval provided by user */ > +static int bcm_is_invalid_tv(struct bcm_msg_head *msg_head) > +{ > + if ((msg_head->ival1.tv_sec > BCM_TIMER_SEC_MAX) || > + (msg_head->ival1.tv_usec >= USEC_PER_SEC) || > + (msg_head->ival2.tv_sec > BCM_TIMER_SEC_MAX) || > + (msg_head->ival2.tv_usec >= USEC_PER_SEC)) > + return 1; > + > + return 0; > +} > + > #define CFSIZ(flags) ((flags & CAN_FD_FRAME) ? CANFD_MTU : CAN_MTU) > #define OPSIZ sizeof(struct bcm_op) > #define MHSIZ sizeof(struct bcm_msg_head) > @@ -873,6 +888,10 @@ static int bcm_tx_setup(struct bcm_msg_head *msg_head, struct msghdr *msg, > if (msg_head->nframes < 1 || msg_head->nframes > MAX_NFRAMES) > return -EINVAL; > > + /* check timeval limitations */ > + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) > + return -EINVAL; > + > /* check the given can_id */ > op = bcm_find_op(&bo->tx_ops, msg_head, ifindex); > if (op) { > @@ -1053,6 +1072,10 @@ static int bcm_rx_setup(struct bcm_msg_head *msg_head, struct msghdr *msg, > (!(msg_head->can_id & CAN_RTR_FLAG)))) > return -EINVAL; > > + /* check timeval limitations */ > + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) > + return -EINVAL; > + > /* check the given can_id */ > op = bcm_find_op(&bo->rx_ops, msg_head, ifindex); > if (op) { > ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH] can: bcm: check timer values before ktime conversion 2019-01-12 22:16 ` Andre Naujoks 2019-01-12 22:16 ` Andre Naujoks @ 2019-01-12 22:30 ` Oliver Hartkopp 2019-01-12 22:30 ` Oliver Hartkopp 2019-01-12 22:45 ` Andre Naujoks 1 sibling, 2 replies; 10+ messages in thread From: Oliver Hartkopp @ 2019-01-12 22:30 UTC (permalink / raw) To: Andre Naujoks, davem, netdev Cc: linux-can, lifeasageek, threeearcat, syzkaller, Kyungtae Kim, linux-stable Hi Andre, just wondered whether it makes sense to limit this value for sending cyclic messages or for detecting a timeout on reception. 4.294.967.295 seconds would be ~136 years - this makes no sense to me and I would assume someone applied some (unintended?) stuff into the timeval. Don't you think? Best, Oliver On 1/12/19 11:16 PM, Andre Naujoks wrote: > Hi. > > The 15 minute limit seems arbitrary to me. I'd be surprised if an > (R|T)X_SETUP failed because of a timeout greater than this. Are there > any problems with allowing larger timeouts? If not, I do not see a > reason to restrict this. > > Regards > Andre > > On 1/12/19 10:57 PM, Oliver Hartkopp wrote: >> Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup() when >> the conversion into ktime multiplies the given value with NSEC_PER_USEC (1000). >> >> Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2 >> >> Add a check for the given tv_usec, so that the value stays below one second. >> Additionally limit the tv_sec value to a reasonable value for CAN related >> use-cases of 15 minutes. >> >> Reported-by: Kyungtae Kim <kt0755@gmail.com> >> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> >> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> >> Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26 >> --- >> net/can/bcm.c | 23 +++++++++++++++++++++++ >> 1 file changed, 23 insertions(+) >> >> diff --git a/net/can/bcm.c b/net/can/bcm.c >> index 0af8f0db892a..ff3799be077b 100644 >> --- a/net/can/bcm.c >> +++ b/net/can/bcm.c >> @@ -67,6 +67,9 @@ >> */ >> #define MAX_NFRAMES 256 >> >> +/* limit timers to 15 minutes for sending/timeouts */ >> +#define BCM_TIMER_SEC_MAX (15*60) >> + >> /* use of last_frames[index].flags */ >> #define RX_RECV 0x40 /* received data for this element */ >> #define RX_THR 0x80 /* element not been sent due to throttle feature */ >> @@ -140,6 +143,18 @@ static inline ktime_t bcm_timeval_to_ktime(struct bcm_timeval tv) >> return ktime_set(tv.tv_sec, tv.tv_usec * NSEC_PER_USEC); >> } >> >> +/* check limitations for timeval provided by user */ >> +static int bcm_is_invalid_tv(struct bcm_msg_head *msg_head) >> +{ >> + if ((msg_head->ival1.tv_sec > BCM_TIMER_SEC_MAX) || >> + (msg_head->ival1.tv_usec >= USEC_PER_SEC) || >> + (msg_head->ival2.tv_sec > BCM_TIMER_SEC_MAX) || >> + (msg_head->ival2.tv_usec >= USEC_PER_SEC)) >> + return 1; >> + >> + return 0; >> +} >> + >> #define CFSIZ(flags) ((flags & CAN_FD_FRAME) ? CANFD_MTU : CAN_MTU) >> #define OPSIZ sizeof(struct bcm_op) >> #define MHSIZ sizeof(struct bcm_msg_head) >> @@ -873,6 +888,10 @@ static int bcm_tx_setup(struct bcm_msg_head *msg_head, struct msghdr *msg, >> if (msg_head->nframes < 1 || msg_head->nframes > MAX_NFRAMES) >> return -EINVAL; >> >> + /* check timeval limitations */ >> + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) >> + return -EINVAL; >> + >> /* check the given can_id */ >> op = bcm_find_op(&bo->tx_ops, msg_head, ifindex); >> if (op) { >> @@ -1053,6 +1072,10 @@ static int bcm_rx_setup(struct bcm_msg_head *msg_head, struct msghdr *msg, >> (!(msg_head->can_id & CAN_RTR_FLAG)))) >> return -EINVAL; >> >> + /* check timeval limitations */ >> + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) >> + return -EINVAL; >> + >> /* check the given can_id */ >> op = bcm_find_op(&bo->rx_ops, msg_head, ifindex); >> if (op) { >> > ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH] can: bcm: check timer values before ktime conversion 2019-01-12 22:30 ` Oliver Hartkopp @ 2019-01-12 22:30 ` Oliver Hartkopp 2019-01-12 22:45 ` Andre Naujoks 1 sibling, 0 replies; 10+ messages in thread From: Oliver Hartkopp @ 2019-01-12 22:30 UTC (permalink / raw) To: Andre Naujoks, davem, netdev Cc: linux-can, lifeasageek, threeearcat, syzkaller, Kyungtae Kim, linux-stable Hi Andre, just wondered whether it makes sense to limit this value for sending cyclic messages or for detecting a timeout on reception. 4.294.967.295 seconds would be ~136 years - this makes no sense to me and I would assume someone applied some (unintended?) stuff into the timeval. Don't you think? Best, Oliver On 1/12/19 11:16 PM, Andre Naujoks wrote: > Hi. > > The 15 minute limit seems arbitrary to me. I'd be surprised if an > (R|T)X_SETUP failed because of a timeout greater than this. Are there > any problems with allowing larger timeouts? If not, I do not see a > reason to restrict this. > > Regards > Andre > > On 1/12/19 10:57 PM, Oliver Hartkopp wrote: >> Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup() when >> the conversion into ktime multiplies the given value with NSEC_PER_USEC (1000). >> >> Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2 >> >> Add a check for the given tv_usec, so that the value stays below one second. >> Additionally limit the tv_sec value to a reasonable value for CAN related >> use-cases of 15 minutes. >> >> Reported-by: Kyungtae Kim <kt0755@gmail.com> >> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> >> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> >> Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26 >> --- >> net/can/bcm.c | 23 +++++++++++++++++++++++ >> 1 file changed, 23 insertions(+) >> >> diff --git a/net/can/bcm.c b/net/can/bcm.c >> index 0af8f0db892a..ff3799be077b 100644 >> --- a/net/can/bcm.c >> +++ b/net/can/bcm.c >> @@ -67,6 +67,9 @@ >> */ >> #define MAX_NFRAMES 256 >> >> +/* limit timers to 15 minutes for sending/timeouts */ >> +#define BCM_TIMER_SEC_MAX (15*60) >> + >> /* use of last_frames[index].flags */ >> #define RX_RECV 0x40 /* received data for this element */ >> #define RX_THR 0x80 /* element not been sent due to throttle feature */ >> @@ -140,6 +143,18 @@ static inline ktime_t bcm_timeval_to_ktime(struct bcm_timeval tv) >> return ktime_set(tv.tv_sec, tv.tv_usec * NSEC_PER_USEC); >> } >> >> +/* check limitations for timeval provided by user */ >> +static int bcm_is_invalid_tv(struct bcm_msg_head *msg_head) >> +{ >> + if ((msg_head->ival1.tv_sec > BCM_TIMER_SEC_MAX) || >> + (msg_head->ival1.tv_usec >= USEC_PER_SEC) || >> + (msg_head->ival2.tv_sec > BCM_TIMER_SEC_MAX) || >> + (msg_head->ival2.tv_usec >= USEC_PER_SEC)) >> + return 1; >> + >> + return 0; >> +} >> + >> #define CFSIZ(flags) ((flags & CAN_FD_FRAME) ? CANFD_MTU : CAN_MTU) >> #define OPSIZ sizeof(struct bcm_op) >> #define MHSIZ sizeof(struct bcm_msg_head) >> @@ -873,6 +888,10 @@ static int bcm_tx_setup(struct bcm_msg_head *msg_head, struct msghdr *msg, >> if (msg_head->nframes < 1 || msg_head->nframes > MAX_NFRAMES) >> return -EINVAL; >> >> + /* check timeval limitations */ >> + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) >> + return -EINVAL; >> + >> /* check the given can_id */ >> op = bcm_find_op(&bo->tx_ops, msg_head, ifindex); >> if (op) { >> @@ -1053,6 +1072,10 @@ static int bcm_rx_setup(struct bcm_msg_head *msg_head, struct msghdr *msg, >> (!(msg_head->can_id & CAN_RTR_FLAG)))) >> return -EINVAL; >> >> + /* check timeval limitations */ >> + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) >> + return -EINVAL; >> + >> /* check the given can_id */ >> op = bcm_find_op(&bo->rx_ops, msg_head, ifindex); >> if (op) { >> > ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH] can: bcm: check timer values before ktime conversion 2019-01-12 22:30 ` Oliver Hartkopp 2019-01-12 22:30 ` Oliver Hartkopp @ 2019-01-12 22:45 ` Andre Naujoks 2019-01-12 22:45 ` Andre Naujoks 2019-01-13 8:18 ` Oliver Hartkopp 1 sibling, 2 replies; 10+ messages in thread From: Andre Naujoks @ 2019-01-12 22:45 UTC (permalink / raw) To: Oliver Hartkopp, davem, netdev Cc: linux-can, lifeasageek, threeearcat, syzkaller, Kyungtae Kim, linux-stable I really don't know. That's why I'd be hesitant to restrict this. Maybe limit it to something really out of the ordinary, like a year? I am not sure that for example one hour would be out of the question for some edge cases. Maybe someone wants to do a heartbeat for his/her system with a very low priority. This would mean a TX_SETUP with a timeout of an hour and a RX_SETUP with a timeout of a bit more. If the system allow timeouts in those ranges, I think it should be allowed. If someone wants to wait a year for a CAN frame, however unlikely that might be, why not? Andre. On 1/12/19 11:30 PM, Oliver Hartkopp wrote: > Hi Andre, > > just wondered whether it makes sense to limit this value for sending > cyclic messages or for detecting a timeout on reception. > > 4.294.967.295 seconds would be ~136 years - this makes no sense to me > and I would assume someone applied some (unintended?) stuff into the > timeval. > > Don't you think? > > Best, > Oliver > > On 1/12/19 11:16 PM, Andre Naujoks wrote: >> Hi. >> >> The 15 minute limit seems arbitrary to me. I'd be surprised if an >> (R|T)X_SETUP failed because of a timeout greater than this. Are there >> any problems with allowing larger timeouts? If not, I do not see a >> reason to restrict this. >> >> Regards >> Andre >> >> On 1/12/19 10:57 PM, Oliver Hartkopp wrote: >>> Kyungtae Kim detected a potential integer overflow in >>> bcm_[rx|tx]_setup() when >>> the conversion into ktime multiplies the given value with >>> NSEC_PER_USEC (1000). >>> >>> Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2 >>> >>> Add a check for the given tv_usec, so that the value stays below one >>> second. >>> Additionally limit the tv_sec value to a reasonable value for CAN >>> related >>> use-cases of 15 minutes. >>> >>> Reported-by: Kyungtae Kim <kt0755@gmail.com> >>> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> >>> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> >>> Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26 >>> --- >>> net/can/bcm.c | 23 +++++++++++++++++++++++ >>> 1 file changed, 23 insertions(+) >>> >>> diff --git a/net/can/bcm.c b/net/can/bcm.c >>> index 0af8f0db892a..ff3799be077b 100644 >>> --- a/net/can/bcm.c >>> +++ b/net/can/bcm.c >>> @@ -67,6 +67,9 @@ >>> */ >>> #define MAX_NFRAMES 256 >>> +/* limit timers to 15 minutes for sending/timeouts */ >>> +#define BCM_TIMER_SEC_MAX (15*60) >>> + >>> /* use of last_frames[index].flags */ >>> #define RX_RECV 0x40 /* received data for this element */ >>> #define RX_THR 0x80 /* element not been sent due to throttle >>> feature */ >>> @@ -140,6 +143,18 @@ static inline ktime_t >>> bcm_timeval_to_ktime(struct bcm_timeval tv) >>> return ktime_set(tv.tv_sec, tv.tv_usec * NSEC_PER_USEC); >>> } >>> +/* check limitations for timeval provided by user */ >>> +static int bcm_is_invalid_tv(struct bcm_msg_head *msg_head) >>> +{ >>> + if ((msg_head->ival1.tv_sec > BCM_TIMER_SEC_MAX) || >>> + (msg_head->ival1.tv_usec >= USEC_PER_SEC) || >>> + (msg_head->ival2.tv_sec > BCM_TIMER_SEC_MAX) || >>> + (msg_head->ival2.tv_usec >= USEC_PER_SEC)) >>> + return 1; >>> + >>> + return 0; >>> +} >>> + >>> #define CFSIZ(flags) ((flags & CAN_FD_FRAME) ? CANFD_MTU : CAN_MTU) >>> #define OPSIZ sizeof(struct bcm_op) >>> #define MHSIZ sizeof(struct bcm_msg_head) >>> @@ -873,6 +888,10 @@ static int bcm_tx_setup(struct bcm_msg_head >>> *msg_head, struct msghdr *msg, >>> if (msg_head->nframes < 1 || msg_head->nframes > MAX_NFRAMES) >>> return -EINVAL; >>> + /* check timeval limitations */ >>> + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) >>> + return -EINVAL; >>> + >>> /* check the given can_id */ >>> op = bcm_find_op(&bo->tx_ops, msg_head, ifindex); >>> if (op) { >>> @@ -1053,6 +1072,10 @@ static int bcm_rx_setup(struct bcm_msg_head >>> *msg_head, struct msghdr *msg, >>> (!(msg_head->can_id & CAN_RTR_FLAG)))) >>> return -EINVAL; >>> + /* check timeval limitations */ >>> + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) >>> + return -EINVAL; >>> + >>> /* check the given can_id */ >>> op = bcm_find_op(&bo->rx_ops, msg_head, ifindex); >>> if (op) { >>> >> ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH] can: bcm: check timer values before ktime conversion 2019-01-12 22:45 ` Andre Naujoks @ 2019-01-12 22:45 ` Andre Naujoks 2019-01-13 8:18 ` Oliver Hartkopp 1 sibling, 0 replies; 10+ messages in thread From: Andre Naujoks @ 2019-01-12 22:45 UTC (permalink / raw) To: Oliver Hartkopp, davem, netdev Cc: linux-can, lifeasageek, threeearcat, syzkaller, Kyungtae Kim, linux-stable I really don't know. That's why I'd be hesitant to restrict this. Maybe limit it to something really out of the ordinary, like a year? I am not sure that for example one hour would be out of the question for some edge cases. Maybe someone wants to do a heartbeat for his/her system with a very low priority. This would mean a TX_SETUP with a timeout of an hour and a RX_SETUP with a timeout of a bit more. If the system allow timeouts in those ranges, I think it should be allowed. If someone wants to wait a year for a CAN frame, however unlikely that might be, why not? Andre. On 1/12/19 11:30 PM, Oliver Hartkopp wrote: > Hi Andre, > > just wondered whether it makes sense to limit this value for sending > cyclic messages or for detecting a timeout on reception. > > 4.294.967.295 seconds would be ~136 years - this makes no sense to me > and I would assume someone applied some (unintended?) stuff into the > timeval. > > Don't you think? > > Best, > Oliver > > On 1/12/19 11:16 PM, Andre Naujoks wrote: >> Hi. >> >> The 15 minute limit seems arbitrary to me. I'd be surprised if an >> (R|T)X_SETUP failed because of a timeout greater than this. Are there >> any problems with allowing larger timeouts? If not, I do not see a >> reason to restrict this. >> >> Regards >> Andre >> >> On 1/12/19 10:57 PM, Oliver Hartkopp wrote: >>> Kyungtae Kim detected a potential integer overflow in >>> bcm_[rx|tx]_setup() when >>> the conversion into ktime multiplies the given value with >>> NSEC_PER_USEC (1000). >>> >>> Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2 >>> >>> Add a check for the given tv_usec, so that the value stays below one >>> second. >>> Additionally limit the tv_sec value to a reasonable value for CAN >>> related >>> use-cases of 15 minutes. >>> >>> Reported-by: Kyungtae Kim <kt0755@gmail.com> >>> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> >>> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> >>> Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26 >>> --- >>> net/can/bcm.c | 23 +++++++++++++++++++++++ >>> 1 file changed, 23 insertions(+) >>> >>> diff --git a/net/can/bcm.c b/net/can/bcm.c >>> index 0af8f0db892a..ff3799be077b 100644 >>> --- a/net/can/bcm.c >>> +++ b/net/can/bcm.c >>> @@ -67,6 +67,9 @@ >>> */ >>> #define MAX_NFRAMES 256 >>> +/* limit timers to 15 minutes for sending/timeouts */ >>> +#define BCM_TIMER_SEC_MAX (15*60) >>> + >>> /* use of last_frames[index].flags */ >>> #define RX_RECV 0x40 /* received data for this element */ >>> #define RX_THR 0x80 /* element not been sent due to throttle >>> feature */ >>> @@ -140,6 +143,18 @@ static inline ktime_t >>> bcm_timeval_to_ktime(struct bcm_timeval tv) >>> return ktime_set(tv.tv_sec, tv.tv_usec * NSEC_PER_USEC); >>> } >>> +/* check limitations for timeval provided by user */ >>> +static int bcm_is_invalid_tv(struct bcm_msg_head *msg_head) >>> +{ >>> + if ((msg_head->ival1.tv_sec > BCM_TIMER_SEC_MAX) || >>> + (msg_head->ival1.tv_usec >= USEC_PER_SEC) || >>> + (msg_head->ival2.tv_sec > BCM_TIMER_SEC_MAX) || >>> + (msg_head->ival2.tv_usec >= USEC_PER_SEC)) >>> + return 1; >>> + >>> + return 0; >>> +} >>> + >>> #define CFSIZ(flags) ((flags & CAN_FD_FRAME) ? CANFD_MTU : CAN_MTU) >>> #define OPSIZ sizeof(struct bcm_op) >>> #define MHSIZ sizeof(struct bcm_msg_head) >>> @@ -873,6 +888,10 @@ static int bcm_tx_setup(struct bcm_msg_head >>> *msg_head, struct msghdr *msg, >>> if (msg_head->nframes < 1 || msg_head->nframes > MAX_NFRAMES) >>> return -EINVAL; >>> + /* check timeval limitations */ >>> + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) >>> + return -EINVAL; >>> + >>> /* check the given can_id */ >>> op = bcm_find_op(&bo->tx_ops, msg_head, ifindex); >>> if (op) { >>> @@ -1053,6 +1072,10 @@ static int bcm_rx_setup(struct bcm_msg_head >>> *msg_head, struct msghdr *msg, >>> (!(msg_head->can_id & CAN_RTR_FLAG)))) >>> return -EINVAL; >>> + /* check timeval limitations */ >>> + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) >>> + return -EINVAL; >>> + >>> /* check the given can_id */ >>> op = bcm_find_op(&bo->rx_ops, msg_head, ifindex); >>> if (op) { >>> >> ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH] can: bcm: check timer values before ktime conversion 2019-01-12 22:45 ` Andre Naujoks 2019-01-12 22:45 ` Andre Naujoks @ 2019-01-13 8:18 ` Oliver Hartkopp 2019-01-13 10:45 ` Andre Naujoks 1 sibling, 1 reply; 10+ messages in thread From: Oliver Hartkopp @ 2019-01-13 8:18 UTC (permalink / raw) To: Andre Naujoks, davem, netdev Cc: linux-can, lifeasageek, threeearcat, syzkaller, Kyungtae Kim, linux-stable Hi Andre, On 1/12/19 11:45 PM, Andre Naujoks wrote: > I really don't know. That's why I'd be hesitant to restrict this. Maybe > limit it to something really out of the ordinary, like a year? :-) The intention was to send and monitor cyclic CAN frames within a range of 5 to 5000ms. Even if you want to ping a satellite over CAN in the deep space network ... I would like to introduce some kind of restriction after all. The question is whether e.g. low power use-cases would require some very seldom pings to be monitored. > I am not sure that for example one hour would be out of the question for > some edge cases. Maybe someone wants to do a heartbeat for his/her > system with a very low priority. This would mean a TX_SETUP with a > timeout of an hour and a RX_SETUP with a timeout of a bit more. > > If the system allow timeouts in those ranges, I think it should be > allowed. If someone wants to wait a year for a CAN frame, however > unlikely that might be, why not? That's scary. IMO you would go for another technical approach if you want to communicate over this period of time. Anyway if it's ok for you I would limit the timer to 400 days to have a least a limitation when sending the V2 patch after getting feedback from Kyungtae Kim. Thanks for stepping in! Best, Oliver > > Andre. > > On 1/12/19 11:30 PM, Oliver Hartkopp wrote: >> Hi Andre, >> >> just wondered whether it makes sense to limit this value for sending >> cyclic messages or for detecting a timeout on reception. >> >> 4.294.967.295 seconds would be ~136 years - this makes no sense to me >> and I would assume someone applied some (unintended?) stuff into the >> timeval. >> >> Don't you think? >> >> Best, >> Oliver >> >> On 1/12/19 11:16 PM, Andre Naujoks wrote: >>> Hi. >>> >>> The 15 minute limit seems arbitrary to me. I'd be surprised if an >>> (R|T)X_SETUP failed because of a timeout greater than this. Are there >>> any problems with allowing larger timeouts? If not, I do not see a >>> reason to restrict this. >>> >>> Regards >>> Andre >>> >>> On 1/12/19 10:57 PM, Oliver Hartkopp wrote: >>>> Kyungtae Kim detected a potential integer overflow in >>>> bcm_[rx|tx]_setup() when >>>> the conversion into ktime multiplies the given value with >>>> NSEC_PER_USEC (1000). >>>> >>>> Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2 >>>> >>>> Add a check for the given tv_usec, so that the value stays below one >>>> second. >>>> Additionally limit the tv_sec value to a reasonable value for CAN >>>> related >>>> use-cases of 15 minutes. >>>> >>>> Reported-by: Kyungtae Kim <kt0755@gmail.com> >>>> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> >>>> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> >>>> Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26 >>>> --- >>>> net/can/bcm.c | 23 +++++++++++++++++++++++ >>>> 1 file changed, 23 insertions(+) >>>> >>>> diff --git a/net/can/bcm.c b/net/can/bcm.c >>>> index 0af8f0db892a..ff3799be077b 100644 >>>> --- a/net/can/bcm.c >>>> +++ b/net/can/bcm.c >>>> @@ -67,6 +67,9 @@ >>>> */ >>>> #define MAX_NFRAMES 256 >>>> +/* limit timers to 15 minutes for sending/timeouts */ >>>> +#define BCM_TIMER_SEC_MAX (15*60) >>>> + >>>> /* use of last_frames[index].flags */ >>>> #define RX_RECV 0x40 /* received data for this element */ >>>> #define RX_THR 0x80 /* element not been sent due to throttle >>>> feature */ >>>> @@ -140,6 +143,18 @@ static inline ktime_t >>>> bcm_timeval_to_ktime(struct bcm_timeval tv) >>>> return ktime_set(tv.tv_sec, tv.tv_usec * NSEC_PER_USEC); >>>> } >>>> +/* check limitations for timeval provided by user */ >>>> +static int bcm_is_invalid_tv(struct bcm_msg_head *msg_head) >>>> +{ >>>> + if ((msg_head->ival1.tv_sec > BCM_TIMER_SEC_MAX) || >>>> + (msg_head->ival1.tv_usec >= USEC_PER_SEC) || >>>> + (msg_head->ival2.tv_sec > BCM_TIMER_SEC_MAX) || >>>> + (msg_head->ival2.tv_usec >= USEC_PER_SEC)) >>>> + return 1; >>>> + >>>> + return 0; >>>> +} >>>> + >>>> #define CFSIZ(flags) ((flags & CAN_FD_FRAME) ? CANFD_MTU : CAN_MTU) >>>> #define OPSIZ sizeof(struct bcm_op) >>>> #define MHSIZ sizeof(struct bcm_msg_head) >>>> @@ -873,6 +888,10 @@ static int bcm_tx_setup(struct bcm_msg_head >>>> *msg_head, struct msghdr *msg, >>>> if (msg_head->nframes < 1 || msg_head->nframes > MAX_NFRAMES) >>>> return -EINVAL; >>>> + /* check timeval limitations */ >>>> + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) >>>> + return -EINVAL; >>>> + >>>> /* check the given can_id */ >>>> op = bcm_find_op(&bo->tx_ops, msg_head, ifindex); >>>> if (op) { >>>> @@ -1053,6 +1072,10 @@ static int bcm_rx_setup(struct bcm_msg_head >>>> *msg_head, struct msghdr *msg, >>>> (!(msg_head->can_id & CAN_RTR_FLAG)))) >>>> return -EINVAL; >>>> + /* check timeval limitations */ >>>> + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) >>>> + return -EINVAL; >>>> + >>>> /* check the given can_id */ >>>> op = bcm_find_op(&bo->rx_ops, msg_head, ifindex); >>>> if (op) { >>>> >>> > ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH] can: bcm: check timer values before ktime conversion 2019-01-13 8:18 ` Oliver Hartkopp @ 2019-01-13 10:45 ` Andre Naujoks 0 siblings, 0 replies; 10+ messages in thread From: Andre Naujoks @ 2019-01-13 10:45 UTC (permalink / raw) To: Oliver Hartkopp, davem, netdev Cc: linux-can, lifeasageek, threeearcat, syzkaller, Kyungtae Kim, linux-stable On 1/13/19 9:18 AM, Oliver Hartkopp wrote: > Hi Andre, > > On 1/12/19 11:45 PM, Andre Naujoks wrote: >> I really don't know. That's why I'd be hesitant to restrict this. Maybe >> limit it to something really out of the ordinary, like a year? > > :-) > > The intention was to send and monitor cyclic CAN frames within a range > of 5 to 5000ms. Even if you want to ping a satellite over CAN in the > deep space network ... I would like to introduce some kind of > restriction after all. Hi Oliver, The intended use-case is what I am using the BCM for. The 15 minutes just caught my eye as very close to those 5 seconds in the big scheme of things. The restriction is then there to do what? The kernel, I think, has no problem with these kinds of timeouts. The only justification I see is to avoid accidentally setting high values as timeouts? To catch typos? > > The question is whether e.g. low power use-cases would require some very > seldom pings to be monitored. > >> I am not sure that for example one hour would be out of the question for >> some edge cases. Maybe someone wants to do a heartbeat for his/her >> system with a very low priority. This would mean a TX_SETUP with a >> timeout of an hour and a RX_SETUP with a timeout of a bit more. >> >> If the system allow timeouts in those ranges, I think it should be >> allowed. If someone wants to wait a year for a CAN frame, however >> unlikely that might be, why not? > > That's scary. IMO you would go for another technical approach if you > want to communicate over this period of time. Definitely! > > Anyway if it's ok for you I would limit the timer to 400 days to have a > least a limitation when sending the V2 patch after getting feedback from > Kyungtae Kim. > 400 days seems way less likely to occur than 15 minutes. I give you that :-). I wouldn't want to to be the one responsible for a deep space probe not to wake up, because someone else thought it was a good idea to tunnel CAN over interplanetary IP. If there needs to be a restriction, 400 days would be reasonable in my eyes. Still arbitrary though. > Thanks for stepping in! Don't mention it :-) Regards Andre > > Best, > Oliver> >> >> Andre. >> >> On 1/12/19 11:30 PM, Oliver Hartkopp wrote: >>> Hi Andre, >>> >>> just wondered whether it makes sense to limit this value for sending >>> cyclic messages or for detecting a timeout on reception. >>> >>> 4.294.967.295 seconds would be ~136 years - this makes no sense to me >>> and I would assume someone applied some (unintended?) stuff into the >>> timeval. >>> >>> Don't you think? >>> >>> Best, >>> Oliver >>> >>> On 1/12/19 11:16 PM, Andre Naujoks wrote: >>>> Hi. >>>> >>>> The 15 minute limit seems arbitrary to me. I'd be surprised if an >>>> (R|T)X_SETUP failed because of a timeout greater than this. Are there >>>> any problems with allowing larger timeouts? If not, I do not see a >>>> reason to restrict this. >>>> >>>> Regards >>>> Andre >>>> >>>> On 1/12/19 10:57 PM, Oliver Hartkopp wrote: >>>>> Kyungtae Kim detected a potential integer overflow in >>>>> bcm_[rx|tx]_setup() when >>>>> the conversion into ktime multiplies the given value with >>>>> NSEC_PER_USEC (1000). >>>>> >>>>> Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2 >>>>> >>>>> Add a check for the given tv_usec, so that the value stays below one >>>>> second. >>>>> Additionally limit the tv_sec value to a reasonable value for CAN >>>>> related >>>>> use-cases of 15 minutes. >>>>> >>>>> Reported-by: Kyungtae Kim <kt0755@gmail.com> >>>>> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> >>>>> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> >>>>> Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26 >>>>> --- >>>>> net/can/bcm.c | 23 +++++++++++++++++++++++ >>>>> 1 file changed, 23 insertions(+) >>>>> >>>>> diff --git a/net/can/bcm.c b/net/can/bcm.c >>>>> index 0af8f0db892a..ff3799be077b 100644 >>>>> --- a/net/can/bcm.c >>>>> +++ b/net/can/bcm.c >>>>> @@ -67,6 +67,9 @@ >>>>> */ >>>>> #define MAX_NFRAMES 256 >>>>> +/* limit timers to 15 minutes for sending/timeouts */ >>>>> +#define BCM_TIMER_SEC_MAX (15*60) >>>>> + >>>>> /* use of last_frames[index].flags */ >>>>> #define RX_RECV 0x40 /* received data for this element */ >>>>> #define RX_THR 0x80 /* element not been sent due to throttle >>>>> feature */ >>>>> @@ -140,6 +143,18 @@ static inline ktime_t >>>>> bcm_timeval_to_ktime(struct bcm_timeval tv) >>>>> return ktime_set(tv.tv_sec, tv.tv_usec * NSEC_PER_USEC); >>>>> } >>>>> +/* check limitations for timeval provided by user */ >>>>> +static int bcm_is_invalid_tv(struct bcm_msg_head *msg_head) >>>>> +{ >>>>> + if ((msg_head->ival1.tv_sec > BCM_TIMER_SEC_MAX) || >>>>> + (msg_head->ival1.tv_usec >= USEC_PER_SEC) || >>>>> + (msg_head->ival2.tv_sec > BCM_TIMER_SEC_MAX) || >>>>> + (msg_head->ival2.tv_usec >= USEC_PER_SEC)) >>>>> + return 1; >>>>> + >>>>> + return 0; >>>>> +} >>>>> + >>>>> #define CFSIZ(flags) ((flags & CAN_FD_FRAME) ? CANFD_MTU : CAN_MTU) >>>>> #define OPSIZ sizeof(struct bcm_op) >>>>> #define MHSIZ sizeof(struct bcm_msg_head) >>>>> @@ -873,6 +888,10 @@ static int bcm_tx_setup(struct bcm_msg_head >>>>> *msg_head, struct msghdr *msg, >>>>> if (msg_head->nframes < 1 || msg_head->nframes > MAX_NFRAMES) >>>>> return -EINVAL; >>>>> + /* check timeval limitations */ >>>>> + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) >>>>> + return -EINVAL; >>>>> + >>>>> /* check the given can_id */ >>>>> op = bcm_find_op(&bo->tx_ops, msg_head, ifindex); >>>>> if (op) { >>>>> @@ -1053,6 +1072,10 @@ static int bcm_rx_setup(struct bcm_msg_head >>>>> *msg_head, struct msghdr *msg, >>>>> (!(msg_head->can_id & CAN_RTR_FLAG)))) >>>>> return -EINVAL; >>>>> + /* check timeval limitations */ >>>>> + if ((msg_head->flags & SETTIMER) && bcm_is_invalid_tv(msg_head)) >>>>> + return -EINVAL; >>>>> + >>>>> /* check the given can_id */ >>>>> op = bcm_find_op(&bo->rx_ops, msg_head, ifindex); >>>>> if (op) { >>>>> >>>> >> ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2019-01-13 10:45 UTC | newest] Thread overview: 10+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2019-01-12 21:57 [PATCH] can: bcm: check timer values before ktime conversion Oliver Hartkopp 2019-01-12 21:57 ` Oliver Hartkopp 2019-01-12 22:16 ` Andre Naujoks 2019-01-12 22:16 ` Andre Naujoks 2019-01-12 22:30 ` Oliver Hartkopp 2019-01-12 22:30 ` Oliver Hartkopp 2019-01-12 22:45 ` Andre Naujoks 2019-01-12 22:45 ` Andre Naujoks 2019-01-13 8:18 ` Oliver Hartkopp 2019-01-13 10:45 ` Andre Naujoks
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).