[PATCH net-next v2 1/1] net: stmmac: use GPIO descriptors in stmmac_mdio_reset

[Martin Blumenstingl <martin.blumenstingl@googlemail.com>]

Switch stmmac_mdio_reset to use GPIO descriptors. GPIO core handles the
"snps,reset-gpio" for GPIO descriptors so we don't need to take care of
it inside the driver anymore.

The advantage of this is that we now preserve the GPIO flags which are
passed via devicetree. This is required on some newer Amlogic boards
which use an Open Drain pin for the reset GPIO. This pin can only output
a LOW signal or switch to input mode but it cannot output a HIGH signal.
There are already devicetree bindings for these special cases and GPIO
core already takes care of them but only if we use GPIO descriptors
instead of GPIO numbers.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c | 27 +++++++++----------
 include/linux/stmmac.h                        |  2 +-
 2 files changed, 14 insertions(+), 15 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 093a223fe408..f1c39dd048e7 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -20,11 +20,11 @@
   Maintainer: Giuseppe Cavallaro <peppe.cavallaro@st.com>
 *******************************************************************************/
 
+#include <linux/gpio/consumer.h>
 #include <linux/io.h>
 #include <linux/iopoll.h>
 #include <linux/mii.h>
 #include <linux/of.h>
-#include <linux/of_gpio.h>
 #include <linux/of_mdio.h>
 #include <linux/phy.h>
 #include <linux/slab.h>
@@ -251,37 +251,36 @@ int stmmac_mdio_reset(struct mii_bus *bus)
 
 #ifdef CONFIG_OF
 	if (priv->device->of_node) {
+		struct gpio_desc *reset_gpio;
+
 		if (data->reset_gpio < 0) {
 			struct device_node *np = priv->device->of_node;
 
 			if (!np)
 				return 0;
 
-			data->reset_gpio = of_get_named_gpio(np,
-						"snps,reset-gpio", 0);
-			if (data->reset_gpio < 0)
-				return 0;
+			reset_gpio = devm_gpiod_get_optional(priv->device,
+							     "snps,reset",
+							     GPIOD_OUT_LOW);
+			if (IS_ERR(reset_gpio))
+				return PTR_ERR(reset_gpio);
 
-			data->active_low = of_property_read_bool(np,
-						"snps,reset-active-low");
 			of_property_read_u32_array(np,
 				"snps,reset-delays-us", data->delays, 3);
+		} else {
+			reset_gpio = gpio_to_desc(data->reset_gpio);
 
-			if (devm_gpio_request(priv->device, data->reset_gpio,
-					      "mdio-reset"))
-				return 0;
+			gpiod_direction_output(reset_gpio, 0);
 		}
 
-		gpio_direction_output(data->reset_gpio,
-				      data->active_low ? 1 : 0);
 		if (data->delays[0])
 			msleep(DIV_ROUND_UP(data->delays[0], 1000));
 
-		gpio_set_value(data->reset_gpio, data->active_low ? 0 : 1);
+		gpiod_set_value_cansleep(reset_gpio, 1);
 		if (data->delays[1])
 			msleep(DIV_ROUND_UP(data->delays[1], 1000));
 
-		gpio_set_value(data->reset_gpio, data->active_low ? 1 : 0);
+		gpiod_set_value_cansleep(reset_gpio, 0);
 		if (data->delays[2])
 			msleep(DIV_ROUND_UP(data->delays[2], 1000));
 	}
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index 4335bd771ce5..816edb545592 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -97,7 +97,7 @@ struct stmmac_mdio_bus_data {
 	int *irqs;
 	int probed_phy_irq;
 #ifdef CONFIG_OF
-	int reset_gpio, active_low;
+	int reset_gpio;
 	u32 delays[3];
 #endif
 };
-- 
2.22.0