[RFC PATCH v2 2/2] Documentation: net: dsa: b53: Describe b53 configuration

[Benedikt Spranger <b.spranger@linutronix.de>]

Document the different needs of documentation for the b53 driver.

Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
---
 Documentation/networking/dsa/b53.rst   | 174 +++++++++++++++++++++++++
 Documentation/networking/dsa/index.rst |   1 +
 2 files changed, 175 insertions(+)
 create mode 100644 Documentation/networking/dsa/b53.rst

diff --git a/Documentation/networking/dsa/b53.rst b/Documentation/networking/dsa/b53.rst
new file mode 100644
index 000000000000..23f1d79a6258
--- /dev/null
+++ b/Documentation/networking/dsa/b53.rst
@@ -0,0 +1,174 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==========================================
+Broadcom RoboSwitch Ethernet switch driver
+==========================================
+
+The Broadcom RoboSwitch Ethernet switch family is used in quite a range of
+xDSL router, cable modems and other multimedia devices.
+
+The actual implementation supports the devices BCM5325E, BCM5365, BCM539x,
+BCM53115 and BCM53125 as well as BCM63XX.
+
+Implementation details
+======================
+
+The driver is located in ``drivers/net/dsa/b53/`` and is implemented as a
+DSA driver; see ``Documentation/networking/dsa/dsa.rst`` for details on the
+subsystem and what it provides.
+
+The switch is, if possible, configured to enable a Broadcom specific 4-bytes
+switch tag which gets inserted by the switch for every packet forwarded to the
+CPU interface, conversely, the CPU network interface should insert a similar
+tag for packets entering the CPU port. The tag format is described in
+``net/dsa/tag_brcm.c``.
+
+The configuration of the device depends on whether or not tagging is
+supported.
+
+The interface names and example network configuration are used according the
+configuration described in the :ref:`dsa-config-showcases`.
+
+Configuration with tagging support
+----------------------------------
+
+The tagging based configuration is desired. It is not specific to the b53
+DSA driver and will work like all DSA drivers which supports tagging.
+
+See :ref:`dsa-tagged-configuration`.
+
+Configuration without tagging support
+-------------------------------------
+
+Older models (5325, 5365) support a different tag format that is not supported
+yet. 539x and 531x5 require managed mode and some special handling, which is
+also not yet supported. The tagging support is disabled in these cases and the
+switch need a different configuration.
+
+The configuration slightly differ from the :ref:`dsa-vlan-configuration`.
+
+single port
+~~~~~~~~~~~
+The configuration can only be set up via VLAN tagging and bridge setup.
+By default packages are tagged with vid 1:
+
+.. code-block:: sh
+
+  # tag traffic on CPU port
+  ip link add link eth0 name eth0.1 type vlan id 1
+  ip link add link eth0 name eth0.2 type vlan id 2
+  ip link add link eth0 name eth0.3 type vlan id 3
+
+  # The master interface needs to be brought up before the slave ports.
+  ip link set eth0 up
+  ip link set eth0.1 up
+  ip link set eth0.2 up
+  ip link set eth0.3 up
+
+  # bring up the slave interfaces
+  ip link set wan up
+  ip link set lan1 up
+  ip link set lan2 up
+
+  # create bridge
+  ip link add name br0 type bridge
+
+  # activate VLAN filtering
+  ip link set dev br0 type bridge vlan_filtering 1
+
+  # add ports to bridges
+  ip link set dev wan master br0
+  ip link set dev lan1 master br0
+  ip link set dev lan2 master br0
+
+  # tag traffic on ports
+  bridge vlan add dev lan1 vid 2 pvid untagged
+  bridge vlan del dev lan1 vid 1
+  bridge vlan add dev lan2 vid 3 pvid untagged
+  bridge vlan del dev lan2 vid 1
+
+  # configure the VLANs
+  ip addr add 192.0.2.1/30 dev eth0.1
+  ip addr add 192.0.2.5/30 dev eth0.2
+  ip addr add 192.0.2.9/30 dev eth0.3
+
+  # bring up the bridge devices
+  ip link set br0 up
+
+
+bridge
+~~~~~~
+
+.. code-block:: sh
+
+  # tag traffic on CPU port
+  ip link add link eth0 name eth0.1 type vlan id 1
+
+  # The master interface needs to be brought up before the slave ports.
+  ip link set eth0 up
+  ip link set eth0.1 up
+
+  # bring up the slave interfaces
+  ip link set wan up
+  ip link set lan1 up
+  ip link set lan2 up
+
+  # create bridge
+  ip link add name br0 type bridge
+
+  # activate VLAN filtering
+  ip link set dev br0 type bridge vlan_filtering 1
+
+  # add ports to bridge
+  ip link set dev wan master br0
+  ip link set dev lan1 master br0
+  ip link set dev lan2 master br0
+  ip link set eth0.1 master br0
+
+  # configure the bridge
+  ip addr add 192.0.2.129/25 dev br0
+
+  # bring up the bridge
+  ip link set dev br0 up
+
+gateway
+~~~~~~~
+
+.. code-block:: sh
+
+  # tag traffic on CPU port
+  ip link add link eth0 name eth0.1 type vlan id 1
+  ip link add link eth0 name eth0.2 type vlan id 2
+
+  # The master interface needs to be brought up before the slave ports.
+  ip link set eth0 up
+  ip link set eth0.1 up
+  ip link set eth0.2 up
+
+  # bring up the slave interfaces
+  ip link set wan up
+  ip link set lan1 up
+  ip link set lan2 up
+
+  # create bridge
+  ip link add name br0 type bridge
+
+  # activate VLAN filtering
+  ip link set dev br0 type bridge vlan_filtering 1
+
+  # add ports to bridges
+  ip link set dev wan master br0
+  ip link set eth0.1 master br0
+  ip link set dev lan1 master br0
+  ip link set dev lan2 master br0
+
+  # tag traffic on ports
+  bridge vlan add dev wan vid 2 pvid untagged
+  bridge vlan del dev wan vid 1
+
+  # configure the VLANs
+  ip addr add 192.0.2.1/30 dev eth0.2
+  ip addr add 192.0.2.129/25 dev br0
+
+  # bring up the bridge devices
+  ip link set br0 up
diff --git a/Documentation/networking/dsa/index.rst b/Documentation/networking/dsa/index.rst
index c279cfbf9083..ee631e2d646f 100644
--- a/Documentation/networking/dsa/index.rst
+++ b/Documentation/networking/dsa/index.rst
@@ -6,6 +6,7 @@ Distributed Switch Architecture
    :maxdepth: 1
 
    dsa
+   b53
    bcm_sf2
    lan9303
    sja1105
-- 
2.20.1