[PATCH AUTOSEL 4.4 01/53] ath10k: Do not send probe response template for mesh

[PATCH AUTOSEL 4.4 01/53] ath10k: Do not send probe response template for mesh

[Sasha Levin]

From: Surabhi Vishnoi <svishnoi@codeaurora.org>

[ Upstream commit 97354f2c432788e3163134df6bb144f4b6289d87 ]

Currently mac80211 do not support probe response template for
mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host
driver tries to configure probe response template for mesh, but
it fails because the interface type is not NL80211_IFTYPE_AP but
NL80211_IFTYPE_MESH_POINT.

To avoid this failure, skip sending probe response template to
firmware for mesh point.

Tested HW: WCN3990/QCA6174/QCA9984

Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/mac.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 398068ad0b62..5a0138c1c045 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -1502,6 +1502,10 @@ static int ath10k_mac_setup_prb_tmpl(struct ath10k_vif *arvif)
 	if (arvif->vdev_type != WMI_VDEV_TYPE_AP)
 		return 0;
 
+	 /* For mesh, probe response and beacon share the same template */
+	if (ieee80211_vif_is_mesh(vif))
+		return 0;
+
 	prb = ieee80211_proberesp_get(hw, vif);
 	if (!prb) {
 		ath10k_warn(ar, "failed to get probe resp template from mac80211\n");
-- 
2.20.1

[PATCH AUTOSEL 4.4 02/53] ath9k: Check for errors when reading SREV register

[Sasha Levin]

From: Tim Schumacher <timschumi@gmx.de>

[ Upstream commit 2f90c7e5d09437a4d8d5546feaae9f1cf48cfbe1 ]

Right now, if an error is encountered during the SREV register
read (i.e. an EIO in ath9k_regread()), that error code gets
passed all the way to __ath9k_hw_init(), where it is visible
during the "Chip rev not supported" message.

    ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
    ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath9k_htc: Failed to initialize the device

Check for -EIO explicitly in ath9k_hw_read_revisions() and return
a boolean based on the success of the operation. Check for that in
__ath9k_hw_init() and abort with a more debugging-friendly message
if reading the revisions wasn't successful.

    ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
    ath: phy2: Failed to read SREV register
    ath: phy2: Could not read hardware revision
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath9k_htc: Failed to initialize the device

This helps when debugging by directly showing the first point of
failure and it could prevent possible errors if a 0x0f.3 revision
is ever supported.

Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath9k/hw.c | 32 +++++++++++++++++++++--------
 1 file changed, 23 insertions(+), 9 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index 4435c7bbb625..d50e2e8bd998 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -250,8 +250,9 @@ void ath9k_hw_get_channel_centers(struct ath_hw *ah,
 /* Chip Revisions */
 /******************/
 
-static void ath9k_hw_read_revisions(struct ath_hw *ah)
+static bool ath9k_hw_read_revisions(struct ath_hw *ah)
 {
+	u32 srev;
 	u32 val;
 
 	if (ah->get_mac_revision)
@@ -267,25 +268,33 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)
 			val = REG_READ(ah, AR_SREV);
 			ah->hw_version.macRev = MS(val, AR_SREV_REVISION2);
 		}
-		return;
+		return true;
 	case AR9300_DEVID_AR9340:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9340;
-		return;
+		return true;
 	case AR9300_DEVID_QCA955X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9550;
-		return;
+		return true;
 	case AR9300_DEVID_AR953X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9531;
-		return;
+		return true;
 	case AR9300_DEVID_QCA956X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9561;
-		return;
+		return true;
 	}
 
-	val = REG_READ(ah, AR_SREV) & AR_SREV_ID;
+	srev = REG_READ(ah, AR_SREV);
+
+	if (srev == -EIO) {
+		ath_err(ath9k_hw_common(ah),
+			"Failed to read SREV register");
+		return false;
+	}
+
+	val = srev & AR_SREV_ID;
 
 	if (val == 0xFF) {
-		val = REG_READ(ah, AR_SREV);
+		val = srev;
 		ah->hw_version.macVersion =
 			(val & AR_SREV_VERSION2) >> AR_SREV_TYPE2_S;
 		ah->hw_version.macRev = MS(val, AR_SREV_REVISION2);
@@ -304,6 +313,8 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)
 		if (ah->hw_version.macVersion == AR_SREV_VERSION_5416_PCIE)
 			ah->is_pciexpress = true;
 	}
+
+	return true;
 }
 
 /************************************/
@@ -556,7 +567,10 @@ static int __ath9k_hw_init(struct ath_hw *ah)
 	struct ath_common *common = ath9k_hw_common(ah);
 	int r = 0;
 
-	ath9k_hw_read_revisions(ah);
+	if (!ath9k_hw_read_revisions(ah)) {
+		ath_err(common, "Could not read hardware revisions");
+		return -EOPNOTSUPP;
+	}
 
 	switch (ah->hw_version.macVersion) {
 	case AR_SREV_VERSION_5416_PCI:
-- 
2.20.1

[PATCH AUTOSEL 4.4 03/53] ath6kl: add some bounds checking

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit 5d6751eaff672ea77642e74e92e6c0ac7f9709ab ]

The "ev->traffic_class" and "reply->ac" variables come from the network
and they're used as an offset into the wmi->stream_exist_for_ac[] array.
Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[]
array only has WMM_NUM_AC (4) elements.  We need to add a couple bounds
checks to prevent array overflows.

I also modified one existing check from "if (traffic_class > 3) {" to
"if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent.

Fixes: bdcd81707973 (" Add ath6kl cleaned up driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath6kl/wmi.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath6kl/wmi.c b/drivers/net/wireless/ath/ath6kl/wmi.c
index a5e1de75a4a3..b2ec254f154e 100644
--- a/drivers/net/wireless/ath/ath6kl/wmi.c
+++ b/drivers/net/wireless/ath/ath6kl/wmi.c
@@ -1178,6 +1178,10 @@ static int ath6kl_wmi_pstream_timeout_event_rx(struct wmi *wmi, u8 *datap,
 		return -EINVAL;
 
 	ev = (struct wmi_pstream_timeout_event *) datap;
+	if (ev->traffic_class >= WMM_NUM_AC) {
+		ath6kl_err("invalid traffic class: %d\n", ev->traffic_class);
+		return -EINVAL;
+	}
 
 	/*
 	 * When the pstream (fat pipe == AC) timesout, it means there were
@@ -1519,6 +1523,10 @@ static int ath6kl_wmi_cac_event_rx(struct wmi *wmi, u8 *datap, int len,
 		return -EINVAL;
 
 	reply = (struct wmi_cac_event *) datap;
+	if (reply->ac >= WMM_NUM_AC) {
+		ath6kl_err("invalid AC: %d\n", reply->ac);
+		return -EINVAL;
+	}
 
 	if ((reply->cac_indication == CAC_INDICATION_ADMISSION_RESP) &&
 	    (reply->status_code != IEEE80211_TSPEC_STATUS_ADMISS_ACCEPTED)) {
@@ -2631,7 +2639,7 @@ int ath6kl_wmi_delete_pstream_cmd(struct wmi *wmi, u8 if_idx, u8 traffic_class,
 	u16 active_tsids = 0;
 	int ret;
 
-	if (traffic_class > 3) {
+	if (traffic_class >= WMM_NUM_AC) {
 		ath6kl_err("invalid traffic class: %d\n", traffic_class);
 		return -EINVAL;
 	}
-- 
2.20.1

[PATCH AUTOSEL 4.4 04/53] ath: DFS JP domain W56 fixed pulse type 3 RADAR detection

[Sasha Levin]

From: Anilkumar Kolli <akolli@codeaurora.org>

[ Upstream commit d8792393a783158cbb2c39939cb897dc5e5299b6 ]

Increase pulse width range from 1-2usec to 0-4usec.
During data traffic HW occasionally fails detecting radar pulses,
so that SW cannot get enough radar reports to achieve the success rate.

Tested ath10k hw and fw:
	* QCA9888(10.4-3.5.1-00052)
	* QCA4019(10.4-3.2.1.1-00017)
	* QCA9984(10.4-3.6-00104)
	* QCA988X(10.2.4-1.0-00041)

Tested ath9k hw: AR9300

Tested-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/dfs_pattern_detector.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/dfs_pattern_detector.c b/drivers/net/wireless/ath/dfs_pattern_detector.c
index 2303ef96299d..0835828ffed7 100644
--- a/drivers/net/wireless/ath/dfs_pattern_detector.c
+++ b/drivers/net/wireless/ath/dfs_pattern_detector.c
@@ -111,7 +111,7 @@ static const struct radar_detector_specs jp_radar_ref_types[] = {
 	JP_PATTERN(0, 0, 1, 1428, 1428, 1, 18, 29, false),
 	JP_PATTERN(1, 2, 3, 3846, 3846, 1, 18, 29, false),
 	JP_PATTERN(2, 0, 1, 1388, 1388, 1, 18, 50, false),
-	JP_PATTERN(3, 1, 2, 4000, 4000, 1, 18, 50, false),
+	JP_PATTERN(3, 0, 4, 4000, 4000, 1, 18, 50, false),
 	JP_PATTERN(4, 0, 5, 150, 230, 1, 23, 50, false),
 	JP_PATTERN(5, 6, 10, 200, 500, 1, 16, 50, false),
 	JP_PATTERN(6, 11, 20, 200, 500, 1, 12, 50, false),
-- 
2.20.1

[PATCH AUTOSEL 4.4 05/53] batman-adv: fix for leaked TVLV handler.

[Sasha Levin]

From: Jeremy Sowden <jeremy@azazel.net>

[ Upstream commit 17f78dd1bd624a4dd78ed5db3284a63ee807fcc3 ]

A handler for BATADV_TVLV_ROAM was being registered when the
translation-table was initialized, but not unregistered when the
translation-table was freed.  Unregister it.

Fixes: 122edaa05940 ("batman-adv: tvlv - convert roaming adv packet to use tvlv unicast packets")
Reported-by: syzbot+d454a826e670502484b8@syzkaller.appspotmail.com
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/batman-adv/translation-table.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/net/batman-adv/translation-table.c b/net/batman-adv/translation-table.c
index f2079acb555d..ffd49b40e76a 100644
--- a/net/batman-adv/translation-table.c
+++ b/net/batman-adv/translation-table.c
@@ -3158,6 +3158,8 @@ static void batadv_tt_purge(struct work_struct *work)
 
 void batadv_tt_free(struct batadv_priv *bat_priv)
 {
+	batadv_tvlv_handler_unregister(bat_priv, BATADV_TVLV_ROAM, 1);
+
 	batadv_tvlv_container_unregister(bat_priv, BATADV_TVLV_TT, 1);
 	batadv_tvlv_handler_unregister(bat_priv, BATADV_TVLV_TT, 1);
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 10/53] net: stmmac: dwmac1000: Clear unused address entries

[Sasha Levin]

From: Jose Abreu <Jose.Abreu@synopsys.com>

[ Upstream commit 9463c445590091202659cdfdd44b236acadfbd84 ]

In case we don't use a given address entry we need to clear it because
it could contain previous values that are no longer valid.

Found out while running stmmac selftests.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
index 371a669d69fd..1df84c8de9d7 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
@@ -187,6 +187,12 @@ static void dwmac1000_set_filter(struct mac_device_info *hw,
 					    GMAC_ADDR_LOW(reg));
 			reg++;
 		}
+
+		while (reg <= perfect_addr_number) {
+			writel(0, ioaddr + GMAC_ADDR_HIGH(reg));
+			writel(0, ioaddr + GMAC_ADDR_LOW(reg));
+			reg++;
+		}
 	}
 
 #ifdef FRAME_FILTER_DEBUG
-- 
2.20.1

[PATCH AUTOSEL 4.4 13/53] af_key: fix leaks in key_pol_get_resp and dump_sp.

[Sasha Levin]

From: Jeremy Sowden <jeremy@azazel.net>

[ Upstream commit 7c80eb1c7e2b8420477fbc998971d62a648035d9 ]

In both functions, if pfkey_xfrm_policy2msg failed we leaked the newly
allocated sk_buff.  Free it on error.

Fixes: 55569ce256ce ("Fix conversion between IPSEC_MODE_xxx and XFRM_MODE_xxx.")
Reported-by: syzbot+4f0529365f7f2208d9f0@syzkaller.appspotmail.com
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/key/af_key.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/net/key/af_key.c b/net/key/af_key.c
index 3ba903ff2bb0..36db179d848e 100644
--- a/net/key/af_key.c
+++ b/net/key/af_key.c
@@ -2463,8 +2463,10 @@ static int key_pol_get_resp(struct sock *sk, struct xfrm_policy *xp, const struc
 		goto out;
 	}
 	err = pfkey_xfrm_policy2msg(out_skb, xp, dir);
-	if (err < 0)
+	if (err < 0) {
+		kfree_skb(out_skb);
 		goto out;
+	}
 
 	out_hdr = (struct sadb_msg *) out_skb->data;
 	out_hdr->sadb_msg_version = hdr->sadb_msg_version;
@@ -2717,8 +2719,10 @@ static int dump_sp(struct xfrm_policy *xp, int dir, int count, void *ptr)
 		return PTR_ERR(out_skb);
 
 	err = pfkey_xfrm_policy2msg(out_skb, xp, dir);
-	if (err < 0)
+	if (err < 0) {
+		kfree_skb(out_skb);
 		return err;
+	}
 
 	out_hdr = (struct sadb_msg *) out_skb->data;
 	out_hdr->sadb_msg_version = pfk->dump.msg_version;
-- 
2.20.1

[PATCH AUTOSEL 4.4 14/53] xfrm: Fix xfrm sel prefix length validation

[Sasha Levin]

From: Anirudh Gupta <anirudhrudr@gmail.com>

[ Upstream commit b38ff4075a80b4da5cb2202d7965332ca0efb213 ]

Family of src/dst can be different from family of selector src/dst.
Use xfrm selector family to validate address prefix length,
while verifying new sa from userspace.

Validated patch with this command:
ip xfrm state add src 1.1.6.1 dst 1.1.6.2 proto esp spi 4260196 \
reqid 20004 mode tunnel aead "rfc4106(gcm(aes))" \
0x1111016400000000000000000000000044440001 128 \
sel src 1011:1:4::2/128 sel dst 1021:1:4::2/128 dev Port5

Fixes: 07bf7908950a ("xfrm: Validate address prefix lengths in the xfrm selector.")
Signed-off-by: Anirudh Gupta <anirudh.gupta@sophos.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/xfrm/xfrm_user.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/net/xfrm/xfrm_user.c b/net/xfrm/xfrm_user.c
index b04c03043976..10fda9a39cc2 100644
--- a/net/xfrm/xfrm_user.c
+++ b/net/xfrm/xfrm_user.c
@@ -150,6 +150,22 @@ static int verify_newsa_info(struct xfrm_usersa_info *p,
 
 	err = -EINVAL;
 	switch (p->family) {
+	case AF_INET:
+		break;
+
+	case AF_INET6:
+#if IS_ENABLED(CONFIG_IPV6)
+		break;
+#else
+		err = -EAFNOSUPPORT;
+		goto out;
+#endif
+
+	default:
+		goto out;
+	}
+
+	switch (p->sel.family) {
 	case AF_INET:
 		if (p->sel.prefixlen_d > 32 || p->sel.prefixlen_s > 32)
 			goto out;
-- 
2.20.1

[PATCH AUTOSEL 4.4 15/53] e1000e: start network tx queue only when link is up

[Sasha Levin]

From: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>

[ Upstream commit d17ba0f616a08f597d9348c372d89b8c0405ccf3 ]

Driver does not want to keep packets in Tx queue when link is lost.
But present code only reset NIC to flush them, but does not prevent
queuing new packets. Moreover reset sequence itself could generate
new packets via netconsole and NIC falls into endless reset loop.

This patch wakes Tx queue only when NIC is ready to send packets.

This is proper fix for problem addressed by commit 0f9e980bf5ee
("e1000e: fix cyclic resets at link up with active tx").

Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 6b1cacd86c6e..7d64edeb1830 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -4171,7 +4171,7 @@ int e1000e_up(struct e1000_adapter *adapter)
 		e1000_configure_msix(adapter);
 	e1000_irq_enable(adapter);
 
-	netif_start_queue(adapter->netdev);
+	/* Tx queue started by watchdog timer when link is up */
 
 	/* fire a link change interrupt to start the watchdog */
 	if (adapter->msix_entries)
@@ -4539,6 +4539,7 @@ static int e1000_open(struct net_device *netdev)
 	pm_runtime_get_sync(&pdev->dev);
 
 	netif_carrier_off(netdev);
+	netif_stop_queue(netdev);
 
 	/* allocate transmit descriptors */
 	err = e1000e_setup_tx_resources(adapter->tx_ring);
@@ -4599,7 +4600,6 @@ static int e1000_open(struct net_device *netdev)
 	e1000_irq_enable(adapter);
 
 	adapter->tx_hang_recheck = false;
-	netif_start_queue(netdev);
 
 	hw->mac.get_link_status = true;
 	pm_runtime_put(&pdev->dev);
@@ -5226,6 +5226,7 @@ static void e1000_watchdog_task(struct work_struct *work)
 			if (phy->ops.cfg_on_link_up)
 				phy->ops.cfg_on_link_up(hw);
 
+			netif_wake_queue(netdev);
 			netif_carrier_on(netdev);
 
 			if (!test_bit(__E1000_DOWN, &adapter->state))
@@ -5239,6 +5240,7 @@ static void e1000_watchdog_task(struct work_struct *work)
 			/* Link status message must follow this format */
 			pr_info("%s NIC Link is Down\n", adapter->netdev->name);
 			netif_carrier_off(netdev);
+			netif_stop_queue(netdev);
 			if (!test_bit(__E1000_DOWN, &adapter->state))
 				mod_timer(&adapter->phy_info_timer,
 					  round_jiffies(jiffies + 2 * HZ));
-- 
2.20.1

[PATCH AUTOSEL 4.4 17/53] net: phy: Check against net_device being NULL

[Sasha Levin]

From: Ioana Ciornei <ioana.ciornei@nxp.com>

[ Upstream commit 82c76aca81187b3d28a6fb3062f6916450ce955e ]

In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/phy/phy_device.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 70f26b30729c..c6a87834723d 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -472,6 +472,9 @@ int phy_connect_direct(struct net_device *dev, struct phy_device *phydev,
 {
 	int rc;
 
+	if (!dev)
+		return -EINVAL;
+
 	rc = phy_attach_direct(dev, phydev, phydev->dev_flags, interface);
 	if (rc)
 		return rc;
@@ -704,6 +707,9 @@ struct phy_device *phy_attach(struct net_device *dev, const char *bus_id,
 	struct device *d;
 	int rc;
 
+	if (!dev)
+		return ERR_PTR(-EINVAL);
+
 	/* Search the list of PHY devices on the mdio bus for the
 	 * PHY with the requested name
 	 */
-- 
2.20.1

[PATCH AUTOSEL 4.4 22/53] net: fec: Do not use netdev messages too early

[Sasha Levin]

From: Fabio Estevam <festevam@gmail.com>

[ Upstream commit a19a0582363b9a5f8ba812f34f1b8df394898780 ]

When a valid MAC address is not found the current messages
are shown:

fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa

Since the network device has not been registered at this point, it is better
to use dev_err()/dev_info() instead, which will provide cleaner log
messages like these:

fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa

Tested on a imx6dl-pico-pi board.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/freescale/fec_main.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index ae8e4fc22e7b..0ee164d09f39 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -1699,10 +1699,10 @@ static void fec_get_mac(struct net_device *ndev)
 	 */
 	if (!is_valid_ether_addr(iap)) {
 		/* Report it and use a random ethernet address instead */
-		netdev_err(ndev, "Invalid MAC address: %pM\n", iap);
+		dev_err(&fep->pdev->dev, "Invalid MAC address: %pM\n", iap);
 		eth_hw_addr_random(ndev);
-		netdev_info(ndev, "Using random MAC address: %pM\n",
-			    ndev->dev_addr);
+		dev_info(&fep->pdev->dev, "Using random MAC address: %pM\n",
+			 ndev->dev_addr);
 		return;
 	}
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 23/53] net: axienet: Fix race condition causing TX hang

[Sasha Levin]

From: Robert Hancock <hancock@sedsystems.ca>

[ Upstream commit 7de44285c1f69ccfbe8be1d6a16fcd956681fee6 ]

It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in axienet_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.

To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../net/ethernet/xilinx/xilinx_axienet_main.c | 20 ++++++++++++++++---
 1 file changed, 17 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
index 58ba579793f8..f1e969128a4e 100644
--- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
@@ -613,6 +613,10 @@ static void axienet_start_xmit_done(struct net_device *ndev)
 
 	ndev->stats.tx_packets += packets;
 	ndev->stats.tx_bytes += size;
+
+	/* Matches barrier in axienet_start_xmit */
+	smp_mb();
+
 	netif_wake_queue(ndev);
 }
 
@@ -667,9 +671,19 @@ static int axienet_start_xmit(struct sk_buff *skb, struct net_device *ndev)
 	cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
 
 	if (axienet_check_tx_bd_space(lp, num_frag)) {
-		if (!netif_queue_stopped(ndev))
-			netif_stop_queue(ndev);
-		return NETDEV_TX_BUSY;
+		if (netif_queue_stopped(ndev))
+			return NETDEV_TX_BUSY;
+
+		netif_stop_queue(ndev);
+
+		/* Matches barrier in axienet_start_xmit_done */
+		smp_mb();
+
+		/* Space might have just been freed - check again */
+		if (axienet_check_tx_bd_space(lp, num_frag))
+			return NETDEV_TX_BUSY;
+
+		netif_wake_queue(ndev);
 	}
 
 	if (skb->ip_summed == CHECKSUM_PARTIAL) {
-- 
2.20.1

[PATCH AUTOSEL 4.4 29/53] bpf: silence warning messages in core

[Sasha Levin]

From: Valdis Klētnieks <valdis.kletnieks@vt.edu>

[ Upstream commit aee450cbe482a8c2f6fa5b05b178ef8b8ff107ca ]

Compiling kernel/bpf/core.c with W=1 causes a flood of warnings:

kernel/bpf/core.c:1198:65: warning: initialized field overwritten [-Woverride-init]
 1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true
      |                                                                 ^~~~
kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL'
 1087 |  INSN_3(ALU, ADD,  X),   \
      |  ^~~~~~
kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP'
 1202 |   BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL),
      |   ^~~~~~~~~~~~
kernel/bpf/core.c:1198:65: note: (near initialization for 'public_insntable[12]')
 1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true
      |                                                                 ^~~~
kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL'
 1087 |  INSN_3(ALU, ADD,  X),   \
      |  ^~~~~~
kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP'
 1202 |   BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL),
      |   ^~~~~~~~~~~~

98 copies of the above.

The attached patch silences the warnings, because we *know* we're overwriting
the default initializer. That leaves bpf/core.c with only 6 other warnings,
which become more visible in comparison.

Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 kernel/bpf/Makefile | 1 +
 1 file changed, 1 insertion(+)

diff --git a/kernel/bpf/Makefile b/kernel/bpf/Makefile
index 13272582eee0..677991f29d66 100644
--- a/kernel/bpf/Makefile
+++ b/kernel/bpf/Makefile
@@ -1,4 +1,5 @@
 obj-y := core.o
+CFLAGS_core.o += $(call cc-disable-warning, override-init)
 
 obj-$(CONFIG_BPF_SYSCALL) += syscall.o verifier.o inode.o helpers.o
 obj-$(CONFIG_BPF_SYSCALL) += hashtab.o arraymap.o
-- 
2.20.1

[PATCH AUTOSEL 4.4 31/53] xfrm: fix sa selector validation

[Sasha Levin]

From: Nicolas Dichtel <nicolas.dichtel@6wind.com>

[ Upstream commit b8d6d0079757cbd1b69724cfd1c08e2171c68cee ]

After commit b38ff4075a80, the following command does not work anymore:
$ ip xfrm state add src 10.125.0.2 dst 10.125.0.1 proto esp spi 34 reqid 1 \
  mode tunnel enc 'cbc(aes)' 0xb0abdba8b782ad9d364ec81e3a7d82a1 auth-trunc \
  'hmac(sha1)' 0xe26609ebd00acb6a4d51fca13e49ea78a72c73e6 96 flag align4

In fact, the selector is not mandatory, allow the user to provide an empty
selector.

Fixes: b38ff4075a80 ("xfrm: Fix xfrm sel prefix length validation")
CC: Anirudh Gupta <anirudh.gupta@sophos.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/xfrm/xfrm_user.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/net/xfrm/xfrm_user.c b/net/xfrm/xfrm_user.c
index 10fda9a39cc2..8cc2a9df84fd 100644
--- a/net/xfrm/xfrm_user.c
+++ b/net/xfrm/xfrm_user.c
@@ -166,6 +166,9 @@ static int verify_newsa_info(struct xfrm_usersa_info *p,
 	}
 
 	switch (p->sel.family) {
+	case AF_UNSPEC:
+		break;
+
 	case AF_INET:
 		if (p->sel.prefixlen_d > 32 || p->sel.prefixlen_s > 32)
 			goto out;
-- 
2.20.1

[PATCH AUTOSEL 4.4 33/53] vhost_net: disable zerocopy by default

[Sasha Levin]

From: Jason Wang <jasowang@redhat.com>

[ Upstream commit 098eadce3c622c07b328d0a43dda379b38cf7c5e ]

Vhost_net was known to suffer from HOL[1] issues which is not easy to
fix. Several downstream disable the feature by default. What's more,
the datapath was split and datacopy path got the support of batching
and XDP support recently which makes it faster than zerocopy part for
small packets transmission.

It looks to me that disable zerocopy by default is more
appropriate. It cold be enabled by default again in the future if we
fix the above issues.

[1] https://patchwork.kernel.org/patch/3787671/

Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/vhost/net.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/vhost/net.c b/drivers/vhost/net.c
index 645b2197930e..f46317135224 100644
--- a/drivers/vhost/net.c
+++ b/drivers/vhost/net.c
@@ -30,7 +30,7 @@
 
 #include "vhost.h"
 
-static int experimental_zcopytx = 1;
+static int experimental_zcopytx = 0;
 module_param(experimental_zcopytx, int, 0444);
 MODULE_PARM_DESC(experimental_zcopytx, "Enable Zero Copy TX;"
 		                       " 1 -Enable; 0 - Disable");
-- 
2.20.1

[PATCH AUTOSEL 4.4 41/53] mt7601u: do not schedule rx_tasklet when the device has been disconnected

[Sasha Levin]

From: Lorenzo Bianconi <lorenzo@kernel.org>

[ Upstream commit 4079e8ccabc3b6d1b503f2376123cb515d14921f ]

Do not schedule rx_tasklet when the usb dongle is disconnected.
Moreover do not grub rx_lock in mt7601u_kill_rx since usb_poison_urb
can run concurrently with urb completion and we can unlink urbs from rx
ring in any order.
This patch fixes the common kernel warning reported when
the device is removed.

[   24.921354] usb 3-14: USB disconnect, device number 7
[   24.921593] ------------[ cut here ]------------
[   24.921594] RX urb mismatch
[   24.921675] WARNING: CPU: 4 PID: 163 at drivers/net/wireless/mediatek/mt7601u/dma.c:200 mt7601u_complete_rx+0xcb/0xd0 [mt7601u]
[   24.921769] CPU: 4 PID: 163 Comm: kworker/4:2 Tainted: G           OE     4.19.31-041931-generic #201903231635
[   24.921770] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./Z97 Extreme4, BIOS P1.30 05/23/2014
[   24.921782] Workqueue: usb_hub_wq hub_event
[   24.921797] RIP: 0010:mt7601u_complete_rx+0xcb/0xd0 [mt7601u]
[   24.921800] RSP: 0018:ffff9bd9cfd03d08 EFLAGS: 00010086
[   24.921802] RAX: 0000000000000000 RBX: ffff9bd9bf043540 RCX: 0000000000000006
[   24.921803] RDX: 0000000000000007 RSI: 0000000000000096 RDI: ffff9bd9cfd16420
[   24.921804] RBP: ffff9bd9cfd03d28 R08: 0000000000000002 R09: 00000000000003a8
[   24.921805] R10: 0000002f485fca34 R11: 0000000000000000 R12: ffff9bd9bf043c1c
[   24.921806] R13: ffff9bd9c62fa3c0 R14: 0000000000000082 R15: 0000000000000000
[   24.921807] FS:  0000000000000000(0000) GS:ffff9bd9cfd00000(0000) knlGS:0000000000000000
[   24.921808] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   24.921808] CR2: 00007fb2648b0000 CR3: 0000000142c0a004 CR4: 00000000001606e0
[   24.921809] Call Trace:
[   24.921812]  <IRQ>
[   24.921819]  __usb_hcd_giveback_urb+0x8b/0x140
[   24.921821]  usb_hcd_giveback_urb+0xca/0xe0
[   24.921828]  xhci_giveback_urb_in_irq.isra.42+0x82/0xf0
[   24.921834]  handle_cmd_completion+0xe02/0x10d0
[   24.921837]  xhci_irq+0x274/0x4a0
[   24.921838]  xhci_msi_irq+0x11/0x20
[   24.921851]  __handle_irq_event_percpu+0x44/0x190
[   24.921856]  handle_irq_event_percpu+0x32/0x80
[   24.921861]  handle_irq_event+0x3b/0x5a
[   24.921867]  handle_edge_irq+0x80/0x190
[   24.921874]  handle_irq+0x20/0x30
[   24.921889]  do_IRQ+0x4e/0xe0
[   24.921891]  common_interrupt+0xf/0xf
[   24.921892]  </IRQ>
[   24.921900] RIP: 0010:usb_hcd_flush_endpoint+0x78/0x180
[   24.921354] usb 3-14: USB disconnect, device number 7

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt7601u/dma.c | 33 +++++++++++----------
 1 file changed, 18 insertions(+), 15 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt7601u/dma.c b/drivers/net/wireless/mediatek/mt7601u/dma.c
index 57a80cfa39b1..6ba30129a3d8 100644
--- a/drivers/net/wireless/mediatek/mt7601u/dma.c
+++ b/drivers/net/wireless/mediatek/mt7601u/dma.c
@@ -193,10 +193,23 @@ static void mt7601u_complete_rx(struct urb *urb)
 	struct mt7601u_rx_queue *q = &dev->rx_q;
 	unsigned long flags;
 
-	spin_lock_irqsave(&dev->rx_lock, flags);
+	/* do no schedule rx tasklet if urb has been unlinked
+	 * or the device has been removed
+	 */
+	switch (urb->status) {
+	case -ECONNRESET:
+	case -ESHUTDOWN:
+	case -ENOENT:
+		return;
+	default:
+		dev_err_ratelimited(dev->dev, "rx urb failed: %d\n",
+				    urb->status);
+		/* fall through */
+	case 0:
+		break;
+	}
 
-	if (mt7601u_urb_has_error(urb))
-		dev_err(dev->dev, "Error: RX urb failed:%d\n", urb->status);
+	spin_lock_irqsave(&dev->rx_lock, flags);
 	if (WARN_ONCE(q->e[q->end].urb != urb, "RX urb mismatch"))
 		goto out;
 
@@ -363,19 +376,9 @@ int mt7601u_dma_enqueue_tx(struct mt7601u_dev *dev, struct sk_buff *skb,
 static void mt7601u_kill_rx(struct mt7601u_dev *dev)
 {
 	int i;
-	unsigned long flags;
 
-	spin_lock_irqsave(&dev->rx_lock, flags);
-
-	for (i = 0; i < dev->rx_q.entries; i++) {
-		int next = dev->rx_q.end;
-
-		spin_unlock_irqrestore(&dev->rx_lock, flags);
-		usb_poison_urb(dev->rx_q.e[next].urb);
-		spin_lock_irqsave(&dev->rx_lock, flags);
-	}
-
-	spin_unlock_irqrestore(&dev->rx_lock, flags);
+	for (i = 0; i < dev->rx_q.entries; i++)
+		usb_poison_urb(dev->rx_q.e[i].urb);
 }
 
 static int mt7601u_submit_rx_buf(struct mt7601u_dev *dev,
-- 
2.20.1

[PATCH AUTOSEL 4.4 43/53] mt7601u: fix possible memory leak when the device is disconnected

[Sasha Levin]

From: Lorenzo Bianconi <lorenzo@kernel.org>

[ Upstream commit 23377c200b2eb48a60d0f228b2a2e75ed6ee6060 ]

When the device is disconnected while passing traffic it is possible
to receive out of order urbs causing a memory leak since the skb linked
to the current tx urb is not removed. Fix the issue deallocating the skb
cleaning up the tx ring. Moreover this patch fixes the following kernel
warning

[   57.480771] usb 1-1: USB disconnect, device number 2
[   57.483451] ------------[ cut here ]------------
[   57.483462] TX urb mismatch
[   57.483481] WARNING: CPU: 1 PID: 32 at drivers/net/wireless/mediatek/mt7601u/dma.c:245 mt7601u_complete_tx+0x165/00
[   57.483483] Modules linked in:
[   57.483496] CPU: 1 PID: 32 Comm: kworker/1:1 Not tainted 5.2.0-rc1+ #72
[   57.483498] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.12.0-2.fc30 04/01/2014
[   57.483502] Workqueue: usb_hub_wq hub_event
[   57.483507] RIP: 0010:mt7601u_complete_tx+0x165/0x1e0
[   57.483510] Code: 8b b5 10 04 00 00 8b 8d 14 04 00 00 eb 8b 80 3d b1 cb e1 00 00 75 9e 48 c7 c7 a4 ea 05 82 c6 05 f
[   57.483513] RSP: 0000:ffffc900000a0d28 EFLAGS: 00010092
[   57.483516] RAX: 000000000000000f RBX: ffff88802c0a62c0 RCX: ffffc900000a0c2c
[   57.483518] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff810a8371
[   57.483520] RBP: ffff88803ced6858 R08: 0000000000000000 R09: 0000000000000001
[   57.483540] R10: 0000000000000002 R11: 0000000000000000 R12: 0000000000000046
[   57.483542] R13: ffff88802c0a6c88 R14: ffff88803baab540 R15: ffff88803a0cc078
[   57.483548] FS:  0000000000000000(0000) GS:ffff88803eb00000(0000) knlGS:0000000000000000
[   57.483550] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   57.483552] CR2: 000055e7f6780100 CR3: 0000000028c86000 CR4: 00000000000006a0
[   57.483554] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   57.483556] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   57.483559] Call Trace:
[   57.483561]  <IRQ>
[   57.483565]  __usb_hcd_giveback_urb+0x77/0xe0
[   57.483570]  xhci_giveback_urb_in_irq.isra.0+0x8b/0x140
[   57.483574]  handle_cmd_completion+0xf5b/0x12c0
[   57.483577]  xhci_irq+0x1f6/0x1810
[   57.483581]  ? lockdep_hardirqs_on+0x9e/0x180
[   57.483584]  ? _raw_spin_unlock_irq+0x24/0x30
[   57.483588]  __handle_irq_event_percpu+0x3a/0x260
[   57.483592]  handle_irq_event_percpu+0x1c/0x60
[   57.483595]  handle_irq_event+0x2f/0x4c
[   57.483599]  handle_edge_irq+0x7e/0x1a0
[   57.483603]  handle_irq+0x17/0x20
[   57.483607]  do_IRQ+0x54/0x110
[   57.483610]  common_interrupt+0xf/0xf
[   57.483612]  </IRQ>

Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt7601u/dma.c | 21 ++++++++++++++++-----
 drivers/net/wireless/mediatek/mt7601u/tx.c  |  4 ++--
 2 files changed, 18 insertions(+), 7 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt7601u/dma.c b/drivers/net/wireless/mediatek/mt7601u/dma.c
index 6ba30129a3d8..3d0b9324d5bf 100644
--- a/drivers/net/wireless/mediatek/mt7601u/dma.c
+++ b/drivers/net/wireless/mediatek/mt7601u/dma.c
@@ -241,14 +241,25 @@ static void mt7601u_complete_tx(struct urb *urb)
 	struct sk_buff *skb;
 	unsigned long flags;
 
-	spin_lock_irqsave(&dev->tx_lock, flags);
+	switch (urb->status) {
+	case -ECONNRESET:
+	case -ESHUTDOWN:
+	case -ENOENT:
+		return;
+	default:
+		dev_err_ratelimited(dev->dev, "tx urb failed: %d\n",
+				    urb->status);
+		/* fall through */
+	case 0:
+		break;
+	}
 
-	if (mt7601u_urb_has_error(urb))
-		dev_err(dev->dev, "Error: TX urb failed:%d\n", urb->status);
+	spin_lock_irqsave(&dev->tx_lock, flags);
 	if (WARN_ONCE(q->e[q->start].urb != urb, "TX urb mismatch"))
 		goto out;
 
 	skb = q->e[q->start].skb;
+	q->e[q->start].skb = NULL;
 	trace_mt_tx_dma_done(dev, skb);
 
 	__skb_queue_tail(&dev->tx_skb_done, skb);
@@ -448,10 +459,10 @@ static void mt7601u_free_tx_queue(struct mt7601u_tx_queue *q)
 {
 	int i;
 
-	WARN_ON(q->used);
-
 	for (i = 0; i < q->entries; i++)  {
 		usb_poison_urb(q->e[i].urb);
+		if (q->e[i].skb)
+			mt7601u_tx_status(q->dev, q->e[i].skb);
 		usb_free_urb(q->e[i].urb);
 	}
 }
diff --git a/drivers/net/wireless/mediatek/mt7601u/tx.c b/drivers/net/wireless/mediatek/mt7601u/tx.c
index a0a33dc8f6bc..a1b6db2a8937 100644
--- a/drivers/net/wireless/mediatek/mt7601u/tx.c
+++ b/drivers/net/wireless/mediatek/mt7601u/tx.c
@@ -117,9 +117,9 @@ void mt7601u_tx_status(struct mt7601u_dev *dev, struct sk_buff *skb)
 	info->status.rates[0].idx = -1;
 	info->flags |= IEEE80211_TX_STAT_ACK;
 
-	spin_lock(&dev->mac_lock);
+	spin_lock_bh(&dev->mac_lock);
 	ieee80211_tx_status(dev->hw, skb);
-	spin_unlock(&dev->mac_lock);
+	spin_unlock_bh(&dev->mac_lock);
 }
 
 static int mt7601u_skb_rooms(struct mt7601u_dev *dev, struct sk_buff *skb)
-- 
2.20.1

[PATCH AUTOSEL 4.4 44/53] ath10k: fix PCIE device wake up failed

[Sasha Levin]

From: Miaoqing Pan <miaoqing@codeaurora.org>

[ Upstream commit 011d4111c8c602ea829fa4917af1818eb0500a90 ]

Observed PCIE device wake up failed after ~120 iterations of
soft-reboot test. The error message is
"ath10k_pci 0000:01:00.0: failed to wake up device : -110"

The call trace as below:
ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait ->
ath10k_pci_is_awake

Once trigger the device to wake up, we will continuously check the RTC
state until it returns RTC_STATE_V_ON or timeout.

But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON.
Occasionally, we get 0x7 on the fist read, we thought as a failure
case, but actually is the right value, also verified with the spec.
So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed
~2000 iterations.

Tested HW: QCA9984

Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/hw.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath10k/hw.c b/drivers/net/wireless/ath/ath10k/hw.c
index 7b84d08a5154..12d6549e45a1 100644
--- a/drivers/net/wireless/ath/ath10k/hw.c
+++ b/drivers/net/wireless/ath/ath10k/hw.c
@@ -128,7 +128,7 @@ const struct ath10k_hw_values qca6174_values = {
 };
 
 const struct ath10k_hw_values qca99x0_values = {
-	.rtc_state_val_on		= 5,
+	.rtc_state_val_on		= 7,
 	.ce_count			= 12,
 	.msi_assign_ce_max		= 12,
 	.num_target_ce_config_wlan	= 10,
-- 
2.20.1

[PATCH AUTOSEL 4.4 47/53] ixgbe: Check DDM existence in transceiver before access

[Sasha Levin]

From: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>

[ Upstream commit 655c91414579d7bb115a4f7898ee726fc18e0984 ]

Some transceivers may comply with SFF-8472 but not implement the Digital
Diagnostic Monitoring (DDM) interface described in it. The existence of
such area is specified by bit 6 of byte 92, set to 1 if implemented.

Currently, due to not checking this bit ixgbe fails trying to read SFP
module's eeprom with the follow message:

ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error

Because it fails to read the additional 256 bytes in which it was assumed
to exist the DDM data.

This issue was noticed using a Mellanox Passive DAC PN 01FT738. The eeprom
data was confirmed by Mellanox as correct and present in other Passive
DACs in from other manufacturers.

Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c | 3 ++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h     | 1 +
 2 files changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
index d681273bd39d..9d38634071a4 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
@@ -3133,7 +3133,8 @@ static int ixgbe_get_module_info(struct net_device *dev,
 		page_swap = true;
 	}
 
-	if (sff8472_rev == IXGBE_SFF_SFF_8472_UNSUP || page_swap) {
+	if (sff8472_rev == IXGBE_SFF_SFF_8472_UNSUP || page_swap ||
+	    !(addr_mode & IXGBE_SFF_DDM_IMPLEMENTED)) {
 		/* We have a SFP, but it does not support SFF-8472 */
 		modinfo->type = ETH_MODULE_SFF_8079;
 		modinfo->eeprom_len = ETH_MODULE_SFF_8079_LEN;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
index 5abd66c84d00..7b7dc6d7d159 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
@@ -70,6 +70,7 @@
 #define IXGBE_SFF_SOFT_RS_SELECT_10G		0x8
 #define IXGBE_SFF_SOFT_RS_SELECT_1G		0x0
 #define IXGBE_SFF_ADDRESSING_MODE		0x4
+#define IXGBE_SFF_DDM_IMPLEMENTED		0x40
 #define IXGBE_SFF_QSFP_DA_ACTIVE_CABLE		0x1
 #define IXGBE_SFF_QSFP_DA_PASSIVE_CABLE		0x8
 #define IXGBE_SFF_QSFP_CONNECTOR_NOT_SEPARABLE	0x23
-- 
2.20.1

[PATCH AUTOSEL 4.4 51/53] Bluetooth: 6lowpan: search for destination address in all peers

[Sasha Levin]

From: Josua Mayer <josua.mayer@jm0.eu>

[ Upstream commit b188b03270b7f8568fc714101ce82fbf5e811c5a ]

Handle overlooked case where the target address is assigned to a peer
and neither route nor gateway exist.

For one peer, no checks are performed to see if it is meant to receive
packets for a given address.

As soon as there is a second peer however, checks are performed
to deal with routes and gateways for handling complex setups with
multiple hops to a target address.
This logic assumed that no route and no gateway imply that the
destination address can not be reached, which is false in case of a
direct peer.

Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Tested-by: Michael Scott <mike@foundries.io>
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/bluetooth/6lowpan.c | 14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)

diff --git a/net/bluetooth/6lowpan.c b/net/bluetooth/6lowpan.c
index 795ddd8b2f77..4cd6b8d811ff 100644
--- a/net/bluetooth/6lowpan.c
+++ b/net/bluetooth/6lowpan.c
@@ -184,10 +184,16 @@ static inline struct lowpan_peer *peer_lookup_dst(struct lowpan_dev *dev,
 	}
 
 	if (!rt) {
-		nexthop = &lowpan_cb(skb)->gw;
-
-		if (ipv6_addr_any(nexthop))
-			return NULL;
+		if (ipv6_addr_any(&lowpan_cb(skb)->gw)) {
+			/* There is neither route nor gateway,
+			 * probably the destination is a direct peer.
+			 */
+			nexthop = daddr;
+		} else {
+			/* There is a known gateway
+			 */
+			nexthop = &lowpan_cb(skb)->gw;
+		}
 	} else {
 		nexthop = rt6_nexthop(rt, daddr);
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 52/53] Bluetooth: Check state in l2cap_disconnect_rsp

[Sasha Levin]

From: Matias Karhumaa <matias.karhumaa@gmail.com>

[ Upstream commit 28261da8a26f4915aa257d12d506c6ba179d961f ]

Because of both sides doing L2CAP disconnection at the same time, it
was possible to receive L2CAP Disconnection Response with CID that was
already freed. That caused problems if CID was already reused and L2CAP
Connection Request with same CID was sent out. Before this patch kernel
deleted channel context regardless of the state of the channel.

Example where leftover Disconnection Response (frame #402) causes local
device to delete L2CAP channel which was not yet connected. This in
turn confuses remote device's stack because same CID is re-used without
properly disconnecting.

Btmon capture before patch:
** snip **
> ACL Data RX: Handle 43 flags 0x02 dlen 8                #394 [hci1] 10.748949
      Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
      RFCOMM: Disconnect (DISC) (0x43)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x53 poll/final 1
         Length: 0
         FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8                #395 [hci1] 10.749062
      Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
      RFCOMM: Unnumbered Ack (UA) (0x63)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x73 poll/final 1
         Length: 0
         FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #396 [hci1] 10.749073
      L2CAP: Disconnection Request (0x06) ident 17 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5    #397 [hci1] 10.752391
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5    #398 [hci1] 10.753394
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #399 [hci1] 10.756499
      L2CAP: Disconnection Request (0x06) ident 26 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #400 [hci1] 10.756548
      L2CAP: Disconnection Response (0x07) ident 26 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #401 [hci1] 10.757459
      L2CAP: Connection Request (0x02) ident 18 len 4
        PSM: 1 (0x0001)
        Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #402 [hci1] 10.759148
      L2CAP: Disconnection Response (0x07) ident 17 len 4
        Destination CID: 65
        Source CID: 65
= bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o..   10.759447
> HCI Event: Number of Completed Packets (0x13) plen 5    #403 [hci1] 10.759386
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #404 [hci1] 10.760397
      L2CAP: Connection Request (0x02) ident 27 len 4
        PSM: 3 (0x0003)
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16               #405 [hci1] 10.760441
      L2CAP: Connection Response (0x03) ident 27 len 8
        Destination CID: 65
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27               #406 [hci1] 10.760449
      L2CAP: Configure Request (0x04) ident 19 len 19
        Destination CID: 65
        Flags: 0x0000
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 1013
        Option: Retransmission and Flow Control (0x04) [mandatory]
          Mode: Basic (0x00)
          TX window size: 0
          Max transmit: 0
          Retransmission timeout: 0
          Monitor timeout: 0
          Maximum PDU size: 0
> HCI Event: Number of Completed Packets (0x13) plen 5    #407 [hci1] 10.761399
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 16               #408 [hci1] 10.762942
      L2CAP: Connection Response (0x03) ident 18 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
*snip*

Similar case after the patch:
*snip*
> ACL Data RX: Handle 43 flags 0x02 dlen 8            #22702 [hci0] 1664.411056
      Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
      RFCOMM: Disconnect (DISC) (0x43)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x53 poll/final 1
         Length: 0
         FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8            #22703 [hci0] 1664.411136
      Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
      RFCOMM: Unnumbered Ack (UA) (0x63)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x73 poll/final 1
         Length: 0
         FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22704 [hci0] 1664.411143
      L2CAP: Disconnection Request (0x06) ident 11 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22705 [hci0] 1664.414009
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22706 [hci0] 1664.415007
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22707 [hci0] 1664.418674
      L2CAP: Disconnection Request (0x06) ident 17 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22708 [hci0] 1664.418762
      L2CAP: Disconnection Response (0x07) ident 17 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22709 [hci0] 1664.421073
      L2CAP: Connection Request (0x02) ident 12 len 4
        PSM: 1 (0x0001)
        Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22710 [hci0] 1664.421371
      L2CAP: Disconnection Response (0x07) ident 11 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22711 [hci0] 1664.424082
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22712 [hci0] 1664.425040
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22713 [hci0] 1664.426103
      L2CAP: Connection Request (0x02) ident 18 len 4
        PSM: 3 (0x0003)
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16           #22714 [hci0] 1664.426186
      L2CAP: Connection Response (0x03) ident 18 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27           #22715 [hci0] 1664.426196
      L2CAP: Configure Request (0x04) ident 13 len 19
        Destination CID: 65
        Flags: 0x0000
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 1013
        Option: Retransmission and Flow Control (0x04) [mandatory]
          Mode: Basic (0x00)
          TX window size: 0
          Max transmit: 0
          Retransmission timeout: 0
          Monitor timeout: 0
          Maximum PDU size: 0
> ACL Data RX: Handle 43 flags 0x02 dlen 16           #22716 [hci0] 1664.428804
      L2CAP: Connection Response (0x03) ident 12 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
*snip*

Fix is to check that channel is in state BT_DISCONN before deleting the
channel.

This bug was found while fuzzing Bluez's OBEX implementation using
Synopsys Defensics.

Reported-by: Matti Kamunen <matti.kamunen@synopsys.com>
Reported-by: Ari Timonen <ari.timonen@synopsys.com>
Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/bluetooth/l2cap_core.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/net/bluetooth/l2cap_core.c b/net/bluetooth/l2cap_core.c
index 46afd560f242..c25f1e4846cd 100644
--- a/net/bluetooth/l2cap_core.c
+++ b/net/bluetooth/l2cap_core.c
@@ -4363,6 +4363,12 @@ static inline int l2cap_disconnect_rsp(struct l2cap_conn *conn,
 
 	l2cap_chan_lock(chan);
 
+	if (chan->state != BT_DISCONN) {
+		l2cap_chan_unlock(chan);
+		mutex_unlock(&conn->chan_lock);
+		return 0;
+	}
+
 	l2cap_chan_hold(chan);
 	l2cap_chan_del(chan, 0);
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 53/53] Bluetooth: validate BLE connection interval updates

[Sasha Levin]

From: csonsino <csonsino@gmail.com>

[ Upstream commit c49a8682fc5d298d44e8d911f4fa14690ea9485e ]

Problem: The Linux Bluetooth stack yields complete control over the BLE
connection interval to the remote device.

The Linux Bluetooth stack provides access to the BLE connection interval
min and max values through /sys/kernel/debug/bluetooth/hci0/
conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval.
These values are used for initial BLE connections, but the remote device
has the ability to request a connection parameter update. In the event
that the remote side requests to change the connection interval, the Linux
kernel currently only validates that the desired value is within the
acceptable range in the Bluetooth specification (6 - 3200, corresponding to
7.5ms - 4000ms). There is currently no validation that the desired value
requested by the remote device is within the min/max limits specified in
the conn_min_interval/conn_max_interval configurations. This essentially
leads to Linux yielding complete control over the connection interval to
the remote device.

The proposed patch adds a verification step to the connection parameter
update mechanism, ensuring that the desired value is within the min/max
bounds of the current connection. If the desired value is outside of the
current connection min/max values, then the connection parameter update
request is rejected and the negative response is returned to the remote
device. Recall that the initial connection is established using the local
conn_min_interval/conn_max_interval values, so this allows the Linux
administrator to retain control over the BLE connection interval.

The one downside that I see is that the current default Linux values for
conn_min_interval and conn_max_interval typically correspond to 30ms and
50ms respectively. If this change were accepted, then it is feasible that
some devices would no longer be able to negotiate to their desired
connection interval values. This might be remedied by setting the default
Linux conn_min_interval and conn_max_interval values to the widest
supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same
behavior as the current implementation, where the remote device could
request to change the connection interval value to any value that is
permitted by the Bluetooth specification, and Linux would accept the
desired value.

Signed-off-by: Carey Sonsino <csonsino@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/bluetooth/hci_event.c  | 5 +++++
 net/bluetooth/l2cap_core.c | 9 ++++++++-
 2 files changed, 13 insertions(+), 1 deletion(-)

diff --git a/net/bluetooth/hci_event.c b/net/bluetooth/hci_event.c
index 37fe2b158c2a..c4e94f34d048 100644
--- a/net/bluetooth/hci_event.c
+++ b/net/bluetooth/hci_event.c
@@ -5062,6 +5062,11 @@ static void hci_le_remote_conn_param_req_evt(struct hci_dev *hdev,
 		return send_conn_param_neg_reply(hdev, handle,
 						 HCI_ERROR_UNKNOWN_CONN_ID);
 
+	if (min < hcon->le_conn_min_interval ||
+	    max > hcon->le_conn_max_interval)
+		return send_conn_param_neg_reply(hdev, handle,
+						 HCI_ERROR_INVALID_LL_PARAMS);
+
 	if (hci_check_conn_params(min, max, latency, timeout))
 		return send_conn_param_neg_reply(hdev, handle,
 						 HCI_ERROR_INVALID_LL_PARAMS);
diff --git a/net/bluetooth/l2cap_core.c b/net/bluetooth/l2cap_core.c
index c25f1e4846cd..8cfba78d26f6 100644
--- a/net/bluetooth/l2cap_core.c
+++ b/net/bluetooth/l2cap_core.c
@@ -5266,7 +5266,14 @@ static inline int l2cap_conn_param_update_req(struct l2cap_conn *conn,
 
 	memset(&rsp, 0, sizeof(rsp));
 
-	err = hci_check_conn_params(min, max, latency, to_multiplier);
+	if (min < hcon->le_conn_min_interval ||
+	    max > hcon->le_conn_max_interval) {
+		BT_DBG("requested connection interval exceeds current bounds.");
+		err = -EINVAL;
+	} else {
+		err = hci_check_conn_params(min, max, latency, to_multiplier);
+	}
+
 	if (err)
 		rsp.result = cpu_to_le16(L2CAP_CONN_PARAM_REJECTED);
 	else
-- 
2.20.1