[PATCH AUTOSEL 4.9 2/9] net sched: fix reporting the first-time use timestamp

[PATCH AUTOSEL 4.9 2/9] net sched: fix reporting the first-time use timestamp

[Sasha Levin]

From: Roman Mashak <mrv@mojatatu.com>

[ Upstream commit b15e62631c5f19fea9895f7632dae9c1b27fe0cd ]

When a new action is installed, firstuse field of 'tcf_t' is explicitly set
to 0. Value of zero means "new action, not yet used"; as a packet hits the
action, 'firstuse' is stamped with the current jiffies value.

tcf_tm_dump() should return 0 for firstuse if action has not yet been hit.

Fixes: 48d8ee1694dd ("net sched actions: aggregate dumping of actions timeinfo")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/net/act_api.h | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/include/net/act_api.h b/include/net/act_api.h
index 82f3c912a5b1..051b90779708 100644
--- a/include/net/act_api.h
+++ b/include/net/act_api.h
@@ -94,7 +94,8 @@ static inline void tcf_tm_dump(struct tcf_t *dtm, const struct tcf_t *stm)
 {
 	dtm->install = jiffies_to_clock_t(jiffies - stm->install);
 	dtm->lastuse = jiffies_to_clock_t(jiffies - stm->lastuse);
-	dtm->firstuse = jiffies_to_clock_t(jiffies - stm->firstuse);
+	dtm->firstuse = stm->firstuse ?
+		jiffies_to_clock_t(jiffies - stm->firstuse) : 0;
 	dtm->expires = jiffies_to_clock_t(stm->expires);
 }
 
-- 
2.25.1

[PATCH AUTOSEL 4.9 4/9] net: bmac: Fix read of MAC address from ROM

[Sasha Levin]

From: Jeremy Kerr <jk@ozlabs.org>

[ Upstream commit ef01cee2ee1b369c57a936166483d40942bcc3e3 ]

In bmac_get_station_address, We're reading two bytes at a time from ROM,
but we do that six times, resulting in 12 bytes of read & writes. This
means we will write off the end of the six-byte destination buffer.

This change fixes the for-loop to only read/write six bytes.

Based on a proposed fix from Finn Thain <fthain@telegraphics.com.au>.

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Reported-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Reported-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/apple/bmac.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/apple/bmac.c b/drivers/net/ethernet/apple/bmac.c
index a65d7a60f116..ffa7e7e6d18d 100644
--- a/drivers/net/ethernet/apple/bmac.c
+++ b/drivers/net/ethernet/apple/bmac.c
@@ -1187,7 +1187,7 @@ bmac_get_station_address(struct net_device *dev, unsigned char *ea)
 	int i;
 	unsigned short data;
 
-	for (i = 0; i < 6; i++)
+	for (i = 0; i < 3; i++)
 		{
 			reset_and_select_srom(dev);
 			data = read_srom(dev, i + EnetAddressOffset/2, SROMAddressBits);
-- 
2.25.1

[PATCH AUTOSEL 4.9 5/9] net/ethernet/freescale: rework quiesce/activate for ucc_geth

[Sasha Levin]

From: Valentin Longchamp <valentin@longchamp.me>

[ Upstream commit 79dde73cf9bcf1dd317a2667f78b758e9fe139ed ]

ugeth_quiesce/activate are used to halt the controller when there is a
link change that requires to reconfigure the mac.

The previous implementation called netif_device_detach(). This however
causes the initial activation of the netdevice to fail precisely because
it's detached. For details, see [1].

A possible workaround was the revert of commit
net: linkwatch: add check for netdevice being present to linkwatch_do_dev
However, the check introduced in the above commit is correct and shall be
kept.

The netif_device_detach() is thus replaced with
netif_tx_stop_all_queues() that prevents any tranmission. This allows to
perform mac config change required by the link change, without detaching
the corresponding netdevice and thus not preventing its initial
activation.

[1] https://lists.openwall.net/netdev/2020/01/08/201

Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Acked-by: Matteo Ghidoni <matteo.ghidoni@ch.abb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/freescale/ucc_geth.c | 13 +++++++------
 1 file changed, 7 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/freescale/ucc_geth.c b/drivers/net/ethernet/freescale/ucc_geth.c
index 714593023bbc..af922bac19ae 100644
--- a/drivers/net/ethernet/freescale/ucc_geth.c
+++ b/drivers/net/ethernet/freescale/ucc_geth.c
@@ -45,6 +45,7 @@
 #include <soc/fsl/qe/ucc.h>
 #include <soc/fsl/qe/ucc_fast.h>
 #include <asm/machdep.h>
+#include <net/sch_generic.h>
 
 #include "ucc_geth.h"
 
@@ -1551,11 +1552,8 @@ static int ugeth_disable(struct ucc_geth_private *ugeth, enum comm_dir mode)
 
 static void ugeth_quiesce(struct ucc_geth_private *ugeth)
 {
-	/* Prevent any further xmits, plus detach the device. */
-	netif_device_detach(ugeth->ndev);
-
-	/* Wait for any current xmits to finish. */
-	netif_tx_disable(ugeth->ndev);
+	/* Prevent any further xmits */
+	netif_tx_stop_all_queues(ugeth->ndev);
 
 	/* Disable the interrupt to avoid NAPI rescheduling. */
 	disable_irq(ugeth->ug_info->uf_info.irq);
@@ -1568,7 +1566,10 @@ static void ugeth_activate(struct ucc_geth_private *ugeth)
 {
 	napi_enable(&ugeth->napi);
 	enable_irq(ugeth->ug_info->uf_info.irq);
-	netif_device_attach(ugeth->ndev);
+
+	/* allow to xmit again  */
+	netif_tx_wake_all_queues(ugeth->ndev);
+	__netdev_watchdog_up(ugeth->ndev);
 }
 
 /* Called every time the controller might need to be made
-- 
2.25.1

[PATCH AUTOSEL 4.9 6/9] net: ethernet: stmmac: Enable interface clocks on probe for IPQ806x

[Sasha Levin]

From: Jonathan McDowell <noodles@earth.li>

[ Upstream commit a96ac8a0045e3cbe3e5af6d1b3c78c6c2065dec5 ]

The ipq806x_gmac_probe() function enables the PTP clock but not the
appropriate interface clocks. This means that if the bootloader hasn't
done so attempting to bring up the interface will fail with an error
like:

[   59.028131] ipq806x-gmac-dwmac 37600000.ethernet: Failed to reset the dma
[   59.028196] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed
[   59.034056] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_open: Hw setup failed

This patch, a slightly cleaned up version of one posted by Sergey
Sergeev in:

https://forum.openwrt.org/t/support-for-mikrotik-rb3011uias-rm/4064/257

correctly enables the clock; we have already configured the source just
before this.

Tested on a MikroTik RB3011.

Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c
index 11a4a81b0397..bcc5d1e16ce2 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c
@@ -330,6 +330,19 @@ static int ipq806x_gmac_probe(struct platform_device *pdev)
 	/* Enable PTP clock */
 	regmap_read(gmac->nss_common, NSS_COMMON_CLK_GATE, &val);
 	val |= NSS_COMMON_CLK_GATE_PTP_EN(gmac->id);
+	switch (gmac->phy_mode) {
+	case PHY_INTERFACE_MODE_RGMII:
+		val |= NSS_COMMON_CLK_GATE_RGMII_RX_EN(gmac->id) |
+			NSS_COMMON_CLK_GATE_RGMII_TX_EN(gmac->id);
+		break;
+	case PHY_INTERFACE_MODE_SGMII:
+		val |= NSS_COMMON_CLK_GATE_GMII_RX_EN(gmac->id) |
+				NSS_COMMON_CLK_GATE_GMII_TX_EN(gmac->id);
+		break;
+	default:
+		/* We don't get here; the switch above will have errored out */
+		unreachable();
+	}
 	regmap_write(gmac->nss_common, NSS_COMMON_CLK_GATE, val);
 
 	if (gmac->phy_mode == PHY_INTERFACE_MODE_SGMII) {
-- 
2.25.1

[PATCH AUTOSEL 4.9 7/9] net: sun: fix missing release regions in cas_init_one().

[Sasha Levin]

From: Qiushi Wu <wu000273@umn.edu>

[ Upstream commit 5a730153984dd13f82ffae93d7170d76eba204e9 ]

In cas_init_one(), "pdev" is requested by "pci_request_regions", but it
was not released after a call of the function “pci_write_config_byte”
failed. Thus replace the jump target “err_write_cacheline” by
"err_out_free_res".

Fixes: 1f26dac32057 ("[NET]: Add Sun Cassini driver.")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/sun/cassini.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/sun/cassini.c b/drivers/net/ethernet/sun/cassini.c
index 062bce9acde6..bfe7b55f9714 100644
--- a/drivers/net/ethernet/sun/cassini.c
+++ b/drivers/net/ethernet/sun/cassini.c
@@ -4980,7 +4980,7 @@ static int cas_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 					  cas_cacheline_size)) {
 			dev_err(&pdev->dev, "Could not set PCI cache "
 			       "line size\n");
-			goto err_write_cacheline;
+			goto err_out_free_res;
 		}
 	}
 #endif
@@ -5151,7 +5151,6 @@ err_out_iounmap:
 err_out_free_res:
 	pci_release_regions(pdev);
 
-err_write_cacheline:
 	/* Try to restore it in case the error occurred after we
 	 * set it.
 	 */
-- 
2.25.1

[PATCH AUTOSEL 4.9 8/9] net/mlx4_core: fix a memory leak bug.

[Sasha Levin]

From: Qiushi Wu <wu000273@umn.edu>

[ Upstream commit febfd9d3c7f74063e8e630b15413ca91b567f963 ]

In function mlx4_opreq_action(), pointer "mailbox" is not released,
when mlx4_cmd_box() return and error, causing a memory leak bug.
Fix this issue by going to "out" label, mlx4_free_cmd_mailbox() can
free this pointer.

Fixes: fe6f700d6cbb ("net/mlx4_core: Respond to operation request by firmware")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/mellanox/mlx4/fw.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/mellanox/mlx4/fw.c b/drivers/net/ethernet/mellanox/mlx4/fw.c
index 9af0887c8a29..fe9dc1b3078c 100644
--- a/drivers/net/ethernet/mellanox/mlx4/fw.c
+++ b/drivers/net/ethernet/mellanox/mlx4/fw.c
@@ -2704,7 +2704,7 @@ void mlx4_opreq_action(struct work_struct *work)
 		if (err) {
 			mlx4_err(dev, "Failed to retrieve required operation: %d\n",
 				 err);
-			return;
+			goto out;
 		}
 		MLX4_GET(modifier, outbox, GET_OP_REQ_MODIFIER_OFFSET);
 		MLX4_GET(token, outbox, GET_OP_REQ_TOKEN_OFFSET);
-- 
2.25.1

[PATCH AUTOSEL 4.9 9/9] net: smsc911x: Fix runtime PM imbalance on error

[Sasha Levin]

From: Dinghao Liu <dinghao.liu@zju.edu.cn>

[ Upstream commit 539d39ad0c61b35f69565a037d7586deaf6d6166 ]

Remove runtime PM usage counter decrement when the
increment function has not been called to keep the
counter balanced.

Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/smsc/smsc911x.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/smsc/smsc911x.c b/drivers/net/ethernet/smsc/smsc911x.c
index 4143659615e1..264136dba674 100644
--- a/drivers/net/ethernet/smsc/smsc911x.c
+++ b/drivers/net/ethernet/smsc/smsc911x.c
@@ -2506,20 +2506,20 @@ static int smsc911x_drv_probe(struct platform_device *pdev)
 
 	retval = smsc911x_init(dev);
 	if (retval < 0)
-		goto out_disable_resources;
+		goto out_init_fail;
 
 	netif_carrier_off(dev);
 
 	retval = smsc911x_mii_init(pdev, dev);
 	if (retval) {
 		SMSC_WARN(pdata, probe, "Error %i initialising mii", retval);
-		goto out_disable_resources;
+		goto out_init_fail;
 	}
 
 	retval = register_netdev(dev);
 	if (retval) {
 		SMSC_WARN(pdata, probe, "Error %i registering device", retval);
-		goto out_disable_resources;
+		goto out_init_fail;
 	} else {
 		SMSC_TRACE(pdata, probe,
 			   "Network interface: \"%s\"", dev->name);
@@ -2560,9 +2560,10 @@ static int smsc911x_drv_probe(struct platform_device *pdev)
 
 	return 0;
 
-out_disable_resources:
+out_init_fail:
 	pm_runtime_put(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
+out_disable_resources:
 	(void)smsc911x_disable_resources(pdev);
 out_enable_resources_fail:
 	smsc911x_free_resources(pdev);
-- 
2.25.1